[PICTURE] menu. Panasonic PT-MZ680

Add to my manuals
210 Pages

advertisement

[PICTURE] menu. Panasonic PT-MZ680 | Manualzz

Chapter 4   Settings — [PICTURE] menu

[PICTURE] menu

On the menu screen, select [PICTURE] from the main menu, and select an item from the sub-menu.

Refer to “Navigating through the menu” ( x page 74) for the operation of the menu screen.

[PICTURE MODE]

You can switch to the desired picture mode suitable for the image source and the environment in which the projector is used.

1) Press as to select [PICTURE MODE].

2) Press qw

or the <ENTER> button.

f The [PICTURE MODE] individual adjustment screen is displayed.

3) Press qw

to switch the item.

f The items will switch each time you press the button.

[STANDARD]

[DYNAMIC]

[DICOM SIM.]

[WHITE BOARD]

[CINEMA]

[NATURAL]

The image becomes suitable for moving images in general.

The image becomes suitable for use in bright areas.

The image becomes similar to that of DICOM Part 14 Grayscale Standard.

The image becomes appropriate to project on a whiteboard.

The image becomes suitable for movie contents.

The image becomes appropriate to use in a dark room.

Note f

DICOM is an abbreviation of “Digital Imaging and COmmunication in Medicine” and is a standard for medical imaging devices. Although the

DICOM name is used, the projector is not a medical device, and display images should not be used for medical purposes such as diagnosis.

[CONTRAST]

You can adjust the contrast of the colors.

1) Press as

to select [CONTRAST].

2) Press qw

or the <ENTER> button.

f The [CONTRAST] individual adjustment screen is displayed.

3) Press qw to adjust the level.

Operation

Press w .

Press q

.

Adjustment

The screen becomes brighter.

The screen becomes darker.

Range of adjustment

-31 - +31

Attention f When it is necessary to adjust [CONTRAST] and [BRIGHTNESS], adjust the [PICTURE] menu → [BRIGHTNESS] first.

[BRIGHTNESS]

You can adjust the dark (black) part of the projected image.

1) Press as to select [BRIGHTNESS].

2) Press qw

or the <ENTER> button.

f The [BRIGHTNESS] individual adjustment screen is displayed.

3) Press qw

to adjust the level.

Operation

Press w

.

Press q

.

Adjustment

Increases the brightness of the dark (black) parts of the screen.

Reduces the brightness of the dark (black) parts of the screen.

Range of adjustment

-31 - +31

ENGLISH - 79

Chapter 4   Settings — [PICTURE] menu

[COLOR]

You can adjust the color saturation of the projected image.

1) Press as to select [COLOR].

2) Press qw or the <ENTER> button.

f The [COLOR] individual adjustment screen is displayed.

3) Press qw

to adjust the level.

Operation

Press w

.

Press q .

Deepens colors.

Weakens colors.

Adjustment

[TINT]

You can adjust the skin tone in the projected image.

1) Press as to select [TINT].

2) Press qw or the <ENTER> button.

f The [TINT] individual adjustment screen is displayed.

3) Press qw

to adjust the level.

Operation

Press w

.

Press q .

Adjustment

Adjusts skin tone toward greenish color.

Adjusts skin tone toward reddish purple.

Range of adjustment

-31 - +31

Range of adjustment

-31 - +31

[COLOR TEMPERATURE]

You can switch the color temperature if the white areas of the projected image are bluish or reddish.

Adjusting with color temperature

1) Press as to select [COLOR TEMPERATURE].

2) Press qw or the <ENTER> button.

f The [COLOR TEMPERATURE] individual adjustment screen is displayed.

3) Press qw to switch the item.

f The items will switch each time you press the button.

[DEFAULT]

[USER]

[LOW]/[HIGH]

Factory default setting.

Adjusts white balance as desired. Refer to “Adjusting desired white balance” ( x

page 80) for details.

Select an item so that images become natural.

Note f

[DEFAULT] cannot be selected when the [PICTURE] menu → [PICTURE MODE] is set to [DICOM SIM.].

f

This item is fixed to [USER] when the [DISPLAY OPTION] menu → [COLOR ADJUSTMENT] is set to anything other than [OFF].

Adjusting desired white balance

1) Press as to select [COLOR TEMPERATURE].

2) Press qw or the <ENTER> button.

f The [COLOR TEMPERATURE] individual adjustment screen is displayed.

3) Press qw to select [USER].

4) Press the <ENTER> button.

f The [COLOR TEMPERATURE] screen is displayed.

80 - ENGLISH

Chapter 4   Settings — [PICTURE] menu

5) Press as to select [WHITE BALANCE].

6) Press the <ENTER> button.

f The [WHITE BALANCE] screen is displayed.

7) Press as to select [WHITE BALANCE HIGH] or [WHITE BALANCE LOW].

8) Press the <ENTER> button.

f The [WHITE BALANCE HIGH] screen or the [WHITE BALANCE LOW] screen is displayed.

9) Press as

to select [RED], [GREEN], or [BLUE].

10) Press qw to adjust the level.

Item

[RED]

[GREEN]

[BLUE]

Operation

Press w .

Press q

.

Press w .

Press q

.

Press w .

Press q

.

Adjustment

Deepens red.

Weakens red.

Deepens green.

Weakens green.

Deepens blue.

Weakens blue.

Range of adjustment

[WHITE BALANCE HIGH]: 0 - +255 (factory default is

+255)

[WHITE BALANCE LOW]: 127 - +127 (factory default is 0)

Note f

Adjust [COLOR TEMPERATURE] correctly. All colors will not be displayed properly unless adequate adjustment is made. If the adjustment does not look suitable, you can press the <DEFAULT> button on the remote control to return the setting for the selected item only to the factory default setting.

Changing the [USER] name

1) Press as

to select [COLOR TEMPERATURE].

2) Press qw

or the <ENTER> button.

f The [COLOR TEMPERATURE] individual adjustment screen is displayed.

3) Press qw to select [USER].

4) Press the <ENTER> button.

f The [COLOR TEMPERATURE] screen is displayed.

5) Press as to select [COLOR TEMPERATURE NAME CHANGE].

6) Press the <ENTER> button.

f The [COLOR TEMPERATURE NAME CHANGE] screen is displayed.

7) Press asqw

to select the text, and press the <ENTER> button to enter the text.

8) Press asqw to select [OK], and press the <ENTER> button.

f

The name set to color temperature is changed.

Note f

When a name is changed, display of [USER] is also changed.

[GAMMA]

You can switch gamma mode.

1) Press as

to select [GAMMA].

2) Press qw or the <ENTER> button.

f

The [GAMMA] individual adjustment screen is displayed.

3) Press qw to adjust the level.

ENGLISH - 81

Operation

Press w .

Press q

.

Chapter 4   Settings — [PICTURE] menu

Adjustment

The intermediate tome becomes brighter.

The intermediate tone becomes darker.

Range of adjustment

-8 - +7

[DAYLIGHT VIEW]

You can correct the image to the optimal vividness even if it is projected under a bright light.

1) Press as

to select [DAYLIGHT VIEW].

2) Press qw or the <ENTER> button.

f

The [DAYLIGHT VIEW] individual adjustment screen is displayed.

3) Press qw to switch the item.

f

The items will switch each time you press the button.

[AUTO]

[OFF]

[1]

[2]

[3]

Detects the brightness of the installed environment by the luminance sensor, and automatically corrects the vividness of the image.

No correction.

Corrects the image to weaken vividness.

Corrects the image to medium vividness.

Corrects the image to high vividness.

Note f [AUTO] cannot be selected when the [PROJECTOR SETUP] menu → [FRONT/REAR] of [PROJECTION METHOD] is set to [REAR].

f The luminance may not be detected correctly when an object is placed on top of the projector, blocking the luminance sensor. In such a case, this function may not operate properly even if it is set to [AUTO].

f When the [PICTURE] menu → [PICTURE MODE] is set to [DICOM SIM.], the factory default value is [OFF].

[SHARPNESS]

You can adjust the sharpness of the projected image.

1) Press as to select [SHARPNESS].

2) Press qw

or the <ENTER> button.

f The [SHARPNESS] individual adjustment screen is displayed.

3) Press qw

to adjust the level.

Operation

Press w

.

Press q .

Contours become sharper.

Contours become softer.

Adjustment Range of adjustment

0 - +15

[NOISE REDUCTION]

You can reduce noises when the input image is degraded and noise is occurring in the image signal.

1) Press as to select [NOISE REDUCTION].

2) Press qw

or the <ENTER> button.

f The [NOISE REDUCTION] individual adjustment screen is displayed.

3) Press qw

to switch the item.

f The items will switch each time you press the button.

[OFF]

[1]

[2]

[3]

No correction.

Slightly corrects the noise.

Moderately corrects the noise.

Strongly corrects the noise.

Attention f

When this is set for an input signal with less noise, the image may look different from the original image. In such a case, set it to [OFF].

82 - ENGLISH

Chapter 4   Settings — [PICTURE] menu

[DYNAMIC CONTRAST]

Light adjustment of the light source and signal compensation are performed automatically according to the image to make the contrast optimum for the image.

1) Press as to select [DYNAMIC CONTRAST].

2) Press qw or the <ENTER> button.

f The [DYNAMIC CONTRAST] individual adjustment screen is displayed.

3) Press qw to switch the item.

f The items will switch each time you press the button.

[OFF]

[1]

[2]

[USER]

Disables the dynamic contrast function.

Adjusts the light source and compensates signals to a small extent.

Adjusts the light source and compensates signals to a large extent.

The light source can be set to turn off when the brightness level of the input video signal falls below a certain value.

Refer to “Setting the light off condition of the light source” ( x

page 83) for details.

Setting the light off condition of the light source

1) Press as

to select [DYNAMIC CONTRAST].

2) Press qw

or the <ENTER> button.

f The [DYNAMIC CONTRAST] individual adjustment screen is displayed.

3) Press qw to select [USER].

4) Press the <ENTER> button.

f The [DYNAMIC CONTRAST] screen is displayed.

5) Press as to select the item to set.

f The items in the detailed setting will switch each time you press qw .

Setting item

[LIGHTS OUT TIMER]

(Setting of the waiting time before turning off the light)

[LIGHTS OUT SIGNAL LEVEL]

(Setting of the brightness level of the signal to turn off the light)

[DISABLE]

[0.5s] ~ [10.0s]

[0%] ~ [5%]

Details

Does not turn off the light source.

Turns off the light source when the brightness level of the video signal being input goes under the value set in [LIGHTS OUT SIGNAL LEVEL].

Select an item from [0.5s] - [4.0s], [5.0s], [7.0s], or [10.0s].

[0.5s] - [4.0s] can be selected in increments of 0.5.

Sets the level of the brightness of the video signal to turn off the light source with [LIGHTS OUT TIMER].

Can be set in increments of 1%. (Factory setting: 0%)

Note f

[LIGHTS OUT SIGNAL LEVEL] cannot be set when [LIGHTS OUT TIMER] is set to [DISABLE].

f

When [LIGHTS OUT TIMER] is set to anything other than [DISABLE], the following are the conditions to turn the light source back on again from the state that the light source has turned off by this function.

g

When the brightness level of the video signal being input has exceeded the value set in [LIGHTS OUT SIGNAL LEVEL] g

When the input signal is gone g

When on-screen display such as menu screen (OSD) or input guide, a test pattern, or a warning message is displayed f

When the image of analog signal is projected, the image may be affected by the signal noise while the brightness level of the video signal is detected. In such case, it is determined that the signal has not fallen below even when the brightness level of the image falls below the value set in [LIGHTS OUT SIGNAL LEVEL].

[SYSTEM SELECTOR]

The projector will automatically detect the input signal, but you can set the system method manually when an unstable signal is input. Set the system method matching the input signal.

1) Press as

to select [SYSTEM SELECTOR].

2) Press the <ENTER> button.

ENGLISH - 83

Chapter 4   Settings — [PICTURE] menu

3) Press as to select a system format.

f

Available system formats vary depending on the input signal.

Terminal

<COMPUTER IN> terminal

<HDMI IN 1> terminal, <HDMI

IN 2> terminal, <HDMI IN 3> terminal, <DIGITAL LINK/

LAN> terminal

System format

576/50p signal Select [RGB] or [YC

B

C

R

].

640 x 480/60 or 480/60p signal Select [640x480/60], [480/60p YC

B

C

R

], or [480/60p RGB].

Other moving image signals Select [RGB] or [YP

B

P

R

].

480/60p or 576/50p signal Select [AUTO], [RGB], or [YC

B

C

R

].

Other moving image signals Select [AUTO], [RGB], or [YP

B

P

R

].

4) Press the <ENTER> button.

Note f

For details of the types of video signals that can be used with the projector, refer to “List of compatible signals” ( x

page 205).

f

This may not function properly for some connected external devices.

84 - ENGLISH

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents