[POSITION] menu. Panasonic PT-MZ680

Add to my manuals
210 Pages

advertisement

[POSITION] menu. Panasonic PT-MZ680 | Manualzz

Chapter 4   Settings — [POSITION] menu

[POSITION] menu

On the menu screen, select [POSITION] from the main menu, and select an item from the sub-menu.

Refer to “Navigating through the menu” ( x page 74) for the operation of the menu screen.

Note f When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the <DIGITAL LINK/

LAN> terminal, adjust the shift, aspect, and clock phase from the menu of DIGITAL LINK output supported device at first.

[SHIFT]

Move the image position vertically or horizontally if the image projected on the screen is still out of position even when the positions of the projector and screen are correct.

1) Press as to select [SHIFT].

2) Press the <ENTER> button.

f The [SHIFT] screen is displayed.

3) Press asqw

to adjust the position.

Orientation Operation Adjustment

Press a .

The image position moves up.

Vertical (up and down) adjustment

Press s

.

The image position moves down.

Press w .

The image position moves to the right.

Horizontal (right and left) adjustment

Press q .

The image position moves to the left.

Note f For the portrait setting, image position is moved horizontally when “Vertical (up and down) adjustment” is made. Image position is moved vertically when “Horizontal (right and left) adjustment” is made.

[ASPECT]

You can switch the aspect ratio of the image.

The aspect ratio is switched within the screen range selected in the [DISPLAY OPTION] menu → [SCREEN

SETTING] → [SCREEN FORMAT]. Set [SCREEN FORMAT] first. ( x page 97)

1) Press as to select [ASPECT].

2) Press qw

or the <ENTER> button.

f The [ASPECT] individual adjustment screen is displayed.

3) Press qw

to switch the item.

f The items will switch each time you press the button.

ENGLISH - 85

Chapter 4   Settings — [POSITION] menu

[NORMAL]

[NATIVE]

[WIDE]

[4:3]

[H FIT]

[V FIT]

[FULL]

Displays images without changing the aspect ratio of the input signals.

Displays images without changing the resolution of the input signals.

Display images by converting the aspect ratio to 16:9 when the standard signal is input *1 signal is input *2 , the images are displayed with the input aspect ratio.

. When wide

Displays images with the input aspect ratio when the standard signal is input *1 is input *2

. When the wide signal

, the images are displayed with the input signal but reduced to fit into the 4:3 screen.

Displays images using the entire width of the screen range selected in [SCREEN FORMAT]. When signals have the aspect ratio vertically longer than the screen aspect ratio selected in [SCREEN

FORMAT], the images are displayed with the top and bottom parts cut off.

Displays images using the entire height of the screen range selected in [SCREEN FORMAT]. When signals have the aspect ratio horizontally longer than the aspect ratio of the screen selected in

[SCREEN FORMAT], the images are displayed with the right and left parts cut off.

Displays images in the entire screen range selected in [SCREEN FORMAT]. When the aspect ratio of the input signals differs from that of the screen range, the images are displayed with the aspect ratio converted to that of the screen selected in [SCREEN FORMAT].

*1 Standard signals are input signals with an aspect ratio of 4:3 or 5:4.

*2 Wide-screen signals are input signals with an aspect ratio of 16:10, 16:9, 15:9 or 15:10.

Note f Some size modes are not available for certain types of input signals. [NATIVE] cannot be selected for a 4K video signal (resolution of

3 840 x 2 160 or 4 096 x 2 160).

f If an aspect ratio which is different from the aspect ratio for the input signals is selected, the images will appear differently from the originals.

Be careful of this when selecting the aspect ratio.

f If using the projector in places such as cafes or hotels to display programs for a commercial purpose or for public presentation, note that adjusting the aspect ratio or using the zoom function to change the screen images may be an infringement of the rights of the original copyright owner for that program under copyright protection laws. Take care when using a function of the projector such as the aspect ratio adjustment and zoom function.

f If conventional (normal) 4:3 images which are not wide-screen images are displayed on a wide screen, the edges of the images may not be visible or they may become distorted. Such images should be viewed as with an aspect ratio of 4:3 in the original format intended by the creator of the images.

[ZOOM]

You can adjust the image size.

The adjustments in [ZOOM] will differ depending on the setting of the [POSITION] menu → [ASPECT].

When [ASPECT] is set to other than [NORMAL] and [NATIVE]

1) Press as to select [ZOOM].

2) Press the <ENTER> button.

f The [ZOOM] screen is displayed.

3) Press as

to select [INTERLOCKED].

4) Press qw

to switch the item.

[OFF]

[ON]

Sets the [VERTICAL] and [HORIZONTAL] zoom ratio.

Uses [BOTH] to set zoom ratio. Image can be enlarged or reduced vertically and horizontally at the same magnification.

5) Press as to select [VERTICAL] or [HORIZONTAL].

f

If [ON] is selected, select [BOTH].

6) Press qw to adjust.

Note f When the [POSITION] menu → [ASPECT] is set to [NATIVE], [ZOOM] cannot be adjusted.

When [ASPECT] is set to [NORMAL]

1) Press as to select [ZOOM].

2) Press the <ENTER> button.

f The [ZOOM] screen is displayed.

86 - ENGLISH

3) Press as to select [MODE].

4) Press qw to switch the item.

Chapter 4   Settings — [POSITION] menu

[INTERNAL]

[FULL]

[OFF]

[ON]

Enlarges the size within the aspect range set with [SCREEN FORMAT].

Enlarges or reduces the size using the entire display area set with [SCREEN FORMAT].

5) Press as

to select [INTERLOCKED].

6) Press qw

to switch the item.

Sets the [VERTICAL] and [HORIZONTAL] zoom ratio.

Uses [BOTH] to set zoom ratio. Image can be enlarged or reduced vertically and horizontally at the same magnification.

7) Press as to select [VERTICAL] or [HORIZONTAL].

f

If [ON] is selected, select [BOTH].

8) Press qw to adjust.

Note f When the [POSITION] menu → [ASPECT] is set to anything other than [NORMAL], [MODE] is not displayed.

[CLOCK PHASE]

You can adjust the image to achieve an optimal image when there is a flickering image or smeared outlines.

1) Press as to select [CLOCK PHASE].

2) Press qw or the <ENTER> button.

f The [CLOCK PHASE] individual adjustment screen is displayed.

3) Press qw

to adjust.

f Adjustment value will change between [0] and [+31]. Adjust the image so that the amount of interference is at a minimum.

Note f Adjustment may not be possible depending on the signal.

f There may be no optimal value if the output from the input computer is unstable.

f There may be no optimal value when the total dot number is shifted.

f [CLOCK PHASE] can be adjusted only when the YC

B

C

R

/YP

B

P

R

signal or the analog RGB signal is input to the <COMPUTER IN> terminal.

f [CLOCK PHASE] cannot be adjusted when a digital signal is input.

f The adjustment value will change to [0] when w is pressed while it was at [+31]. Also, the adjustment value will change to [+31] when q is pressed while it was at [0].

[REALTIME KEYSTONE]

The keystone distortion that occurs when the projector is installed tilted is adjusted automatically.

1) Press as to select [REALTIME KEYSTONE].

2) Press qw

to select the item to adjust.

[OFF]

[ON]

The real-time keystone distortion correction function is not executed automatically.

The real-time keystone distortion correction function is executed automatically.

Note f

The keystone distortion may not be corrected fully depending on the installation condition. In such case, adjust it with the [POSITION] menu

→ [SCREEN ADJUSTMENT].

f

[REALTIME KEYSTONE] cannot be set in following cases.

g

When the [PROJECTOR SETUP] menu → [PROJECTION METHOD] → [FLOOR/CEILING] is set to [CEILING] g

When the [PROJECTOR SETUP] menu → [PROJECTION METHOD] → [FLOOR/CEILING] is set to [AUTO], and the actual installation status is ceiling mount f

When [REALTIME KEYSTONE] and [SCREEN ADJUSTMENT] are both set to [OFF] and [REALTIME KEYSTONE] is changed to [ON],

[SCREEN ADJUSTMENT] is changed to [KEYSTONE].

ENGLISH - 87

Chapter 4   Settings — [POSITION] menu

[SCREEN ADJUSTMENT]

You can correct various types of distortion in a projected image.

Unique image processing technology enables projection of a square image on a special screen shape.

1) Press as to select [SCREEN ADJUSTMENT].

2) Press qw to switch the item.

f The items will switch each time you press the button.

[OFF]

[KEYSTONE]

Does not perform [SCREEN ADJUSTMENT].

Adjusts any trapezoidal distortion in the projected image.

[CORNER CORRECTION] Adjusts any distortion in the four corners of the projected image.

[CURVED CORRECTION] Adjusts any curved distortion in the projected image.

[PC-1]

[PC-2]

[PC-3]

Select this item when performing correction using a computer and “Geometric & Setup Management

Software”* 1 . Up to three correction data can be saved.

*1 “Geometric & Setup Management Software” can be downloaded from the website (https://panasonic.net/cns/projector/pass/). It is necessary to register and login to PASS to download.

Setting [KEYSTONE] or [CURVED CORRECTION]

1) Press as

to select [SCREEN ADJUSTMENT].

2) Press qw to select [KEYSTONE] or [CURVED CORRECTION].

3) Press the <ENTER> button.

f The [KEYSTONE] or [CURVED CORRECTION] screen is displayed.

4) Press as to select the item to adjust.

5) Press qw

to adjust.

[KEYSTONE]

[LENS THROW RATIO]

Set the throw ratio.

Select the value close to the actual projection distance divided by projected image width here.

For details of the projection distance and the projected image width, refer to “Projected image and throw distance” ( x

page 38).

[VERTICAL KEYSTONE] [HORIZONTAL KEYSTONE]

[VERTICAL BALANCE] [HORIZONTAL BALANCE]

Adjust the setting according to the lens shift range in the vertical direction.

Adjust the setting according to the lens shift range in the horizontal direction.

[CURVED CORRECTION]

[LENS THROW RATIO]

Set the throw ratio.

Select the value close to the actual projection distance divided by projected image width here.

For details of the projection distance and the projected image width, refer to “Projected image and throw distance” ( x

page 38).

88 - ENGLISH

[VERTICAL KEYSTONE]

Chapter 4   Settings — [POSITION] menu

[CURVED CORRECTION]

[HORIZONTAL KEYSTONE]

[VERTICAL ARC] [HORIZONTAL ARC]

[VERTICAL BALANCE] [HORIZONTAL BALANCE]

[MAINTAIN ASPECT RATIO]

Select [ON] to correct while keeping the aspect ratio.

Setting [CORNER CORRECTION]

1) Press as to select [SCREEN ADJUSTMENT].

2) Press qw

to select [CORNER CORRECTION].

3) Press the <ENTER> button.

f The [CORNER CORRECTION] screen is displayed.

4) Press as to select the item to adjust, and press the <ENTER> button.

f

When [LINEARITY] is selected, press

Select [AUTO] normally.

qw

to select either adjustment method ([AUTO] or [MANUAL]).

For details of operation when [MANUAL] is selected, refer to “Adjusting to desired linearity” ( x page 90).

5) Press asqw to adjust.

[UPPER LEFT] [UPPER RIGHT]

[CORNER CORRECTION]

[LOWER LEFT] [LOWER RIGHT]

[LINEARITY]

Horizontal direction Vertical direction

ENGLISH - 89

Adjusting to desired linearity

Chapter 4   Settings — [POSITION] menu

1) Press as to select [SCREEN ADJUSTMENT].

2) Press qw

to select [CORNER CORRECTION].

3) Press the <ENTER> button.

f The [CORNER CORRECTION] screen is displayed.

4) Press as to select [LINEARITY].

5) Press qw to select [MANUAL].

6) Press the <ENTER> button.

f The [LINEARITY] screen is displayed.

7) Press asqw

to adjust.

Note f

Depending on the correction value, the aspect ratio of the image may change.

f

The picture quality will degrade more when the correction for [SCREEN ADJUSTMENT] increases, making it harder to focus. Install the projector so that the correction will be as small as possible.

f

Image size will also change when [SCREEN ADJUSTMENT] is used to perform various adjustments.

f

If [SCREEN ADJUSTMENT] and the adjustment in the [ADVANCED MENU] menu → [EDGE BLENDING] are used together, the edge blending may not be adjusted correctly depending on the environment.

f

The image may disappear for a moment or may be disrupted while performing adjustment, but this is not a malfunction.

90 - ENGLISH

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents