[SECURITY] menu. Panasonic PT-MZ680

Add to my manuals
210 Pages

advertisement

[SECURITY] menu. Panasonic PT-MZ680 | Manualzz

Chapter 4   Settings — [SECURITY] menu

[SECURITY] menu

On the menu screen, select [SECURITY] from the main menu, and select an item from the sub-menu.

Refer to “Navigating through the menu” ( x page 74) for the operation of the menu screen.

f When the projector is used for the first time

Initial password: Press awsqawsq in order, and press the <ENTER> button.

Attention f When you select the [SECURITY] menu and press the <ENTER> button, entering a password is prompted. Enter the preset password and then continue operations of the [SECURITY] menu.

f When the password has been changed previously, enter the changed password, and press the <ENTER> button.

Note f

The entered password is displayed with * marks on the screen.

f

An error message is displayed on the screen when the entered password is incorrect. Re-enter the correct password.

[SECURITY PASSWORD]

Display the [SECURITY PASSWORD] screen when the power is turned on with the <MAIN POWER> switch set to the <OFF> side. When the entered password is incorrect, the operation will be restricted to the power < v / b > button.

1) Press as to select [SECURITY PASSWORD].

2) Press qw to switch the item.

f The items will switch each time you press the button.

[OFF]

[ON]

Disables the security password entry.

Enables the security password entry.

Note f

This item is set to [OFF] in the factory default setting or when the [PROJECTOR SETUP] menu → [INITIALIZE] → [ALL USER DATA] is executed. Set it to [ON] as necessary.

f

Change the password periodically that is hard to guess.

f

The security password is enabled after setting the item to [ON] and setting the <MAIN POWER> switch to <OFF>.

[SECURITY PASSWORD CHANGE]

Change the security password.

1) Press as to select [SECURITY PASSWORD CHANGE].

2) Press the <ENTER> button.

f The [SECURITY PASSWORD CHANGE] screen is displayed.

3) Press asqw and the number (<0> - <9>) buttons to set the password.

f Up to eight button operations can be set.

4) Press the <ENTER> button.

5) Re-enter the password for the confirmation.

6) Press the <ENTER> button.

Note f

The entered password is displayed with * marks on the screen.

f

When numerical values are used for the security password, the security password is required to be initialized if the remote control is lost.

Consult your dealer for the method of initialization.

[DISPLAY SETTING]

Overlap the security message (text or image) over the projecting image.

1) Press as to select [DISPLAY SETTING].

ENGLISH - 133

Chapter 4   Settings — [SECURITY] menu

2) Press qw to switch the item.

f

The items will switch each time you press the button.

[OFF]

[TEXT]

[USER LOGO]

Hides the security message.

Displays the text set in the [SECURITY] menu → [TEXT CHANGE].

Displays the image registered by the user.

Note f To create and register the [USER LOGO] image, use “Logo Transfer Software”. The software can be downloaded from the website (https:// panasonic.net/cns/projector/).

[TEXT CHANGE]

Edit the text to be displayed when [TEXT] is selected in [DISPLAY SETTING].

1) Press as to select [TEXT CHANGE].

2) Press the <ENTER> button.

f The [TEXT CHANGE] screen is displayed.

3) Press asqw

to select the text, and press the <ENTER> button to enter the text.

4) Press asqw to select [OK], and press the <ENTER> button.

f

The text is changed.

[MENU LOCK]

Press the <MENU> button to display the menu, and set if menu operation is enabled or not.

1) Press as to select [MENU LOCK].

2) Press qw to switch the item.

f The items will switch each time you press the button.

[OFF]

[ON]

Enables the menu operation.

Disables the menu operation.

Note f This function is set to [OFF] as the factory default setting or after the [PROJECTOR SETUP] menu → [INITIALIZE] → [ALL USER DATA] is executed. Set it to [ON] as necessary.

f When [MENU LOCK] is set to [ON], the [MENU LOCK PASSWORD] screen is displayed by pressing the <MENU> button. Menu operation is enabled by entering the set menu lock password. In this case, enabling of the menu operation is maintained until the projector goes into the standby mode.

[MENU LOCK PASSWORD]

Change the menu lock password.

1) Press as to select [MENU LOCK PASSWORD].

2) Press the <ENTER> button.

f The [MENU LOCK PASSWORD] screen is displayed.

3) Press asqw to select the character, and press the <ENTER> button to enter the character.

f Up to 16 characters can be entered.

4) Press asqw

to select [OK], and press the <ENTER> button.

f To cancel, select [CANCEL].

Attention f The initial password is AAAA as the factory default or after the [PROJECTOR SETUP] menu → [INITIALIZE] → [ALL USER DATA] is executed.

f Change the password periodically and make it hard to guess.

f To initialize your password, consult your distributor.

134 - ENGLISH

Chapter 4   Settings — [SECURITY] menu

[CONTROL DEVICE SETUP]

Enable/disable the button operations on the control panel and the remote control.

1) Press as to select [CONTROL DEVICE SETUP].

2) Press the <ENTER> button.

f The [CONTROL DEVICE SETUP] screen is displayed.

3) Press as

to select [CONTROL PANEL] or [REMOTE CONTROL].

[CONTROL PANEL]

[REMOTE CONTROL]

Sets the limitation on the control from the control panel.

Sets the limitation on the control from the remote control.

4) Press the <ENTER> button.

f The [CONTROL PANEL] screen or the [REMOTE CONTROL] screen is displayed.

5) Press as to select [CONTROL PANEL] or [REMOTE CONTROL].

6) Press qw to switch the item.

f You can set the operation restriction from the control panel or the remote control.

[ENABLE]

[DISABLE]

[USER]

Enables all button operations.

Disables all button operations.

Operation of all buttons can be enabled/disabled separately.

Refer to “Enabling/disabling any button” ( x

page 135) for details.

7) Press as

to select [APPLY], and press the <ENTER> button.

f The confirmation screen is displayed.

8) Press qw

to select [OK], and press the <ENTER> button.

Enabling/disabling any button

1) Press as to select [CONTROL DEVICE SETUP].

2) Press the <ENTER> button.

f The [CONTROL DEVICE SETUP] screen is displayed.

3) Press as to select [CONTROL PANEL] or [REMOTE CONTROL].

4) Press the <ENTER> button.

f The [CONTROL PANEL] screen or the [REMOTE CONTROL] screen is displayed.

5) Press as

to select [CONTROL PANEL] or [REMOTE CONTROL].

6) Press qw to switch [USER].

7) Press as to select the button item to set.

f When [INPUT SELECT BUTTON] is selected in [REMOTE CONTROL], press the <ENTER> button, and then press as to select the button to set.

Buttons that can be set

[REMOTE CONTROL]

[POWER BUTTON] Power < v

/ b

[CONTROL PANEL]

>button

[INPUT SELECT BUTTON] <INPUT SELECT> button

[MENU BUTTON]

[LENS BUTTON]

[AUTO SETUP BUTTON]

[SHUTTER BUTTON]

[ON SCREEN BUTTON]

[OTHER BUTTON]

<MENU> button

<LENS/CANCEL> button

<SHUTTER> button

― asqw , <ENTER> button

<COMPUTER> button, <HDMI 1> button, <HDMI 2> button, <HDMI 3> button, <DIGITAL LINK> button

Lens buttons (<FOCUS>, <ZOOM>, <SHIFT>)

<AUTO SETUP/CANCEL> button

<ON SCREEN> button

Buttons not listed above

ENGLISH - 135

8) Press qw to switch the item.

Chapter 4   Settings — [SECURITY] menu

[ENABLE]

[DISABLE]

Enables button operations.

Disables button operations.

f

When [INPUT SELECT BUTTON] is selected in Step 7) , pressing the <MENU> button returns to the

[CONTROL PANEL] screen or the [REMOTE CONTROL] screen once the item is switched.

9) Press as to select [APPLY], and press the <ENTER> button.

f The confirmation screen is displayed.

10) Press qw to select [OK], and press the <ENTER> button.

Note f When a button operation is performed on the the control panel or remote control where [DISABLE] is set, the [CONTROL DEVICE

PASSWORD] screen is displayed.

Enter the control device password.

f The [CONTROL DEVICE PASSWORD] screen will disappear when there is no operation for approx. 10 seconds.

f When the setting has completed, the menu screen will disappear. To operate continuously, press the <MENU> button to display the main menu.

f Even when you set button operations on the remote control disabled, operations of the <ID SET> and <ID ALL> buttons on the remote control are kept enabled.

[CONTROL DEVICE PASSWORD CHANGE]

The control device password can be changed.

1) Press as to select [CONTROL DEVICE PASSWORD CHANGE].

2) Press the <ENTER> button.

f The [CONTROL DEVICE PASSWORD CHANGE] screen is displayed.

3) Press asqw

to select the text, and press the <ENTER> button to enter the text.

4) Press asqw to select [OK], and press the <ENTER> button.

f To cancel, select [CANCEL].

Attention f

The initial password is “AAAA” as the factory default or when the [PROJECTOR SETUP] menu → [INITIALIZE] → [ALL USER DATA] is executed.

f

Change the password periodically that is hard to guess.

f

To initialize your password, consult your distributor.

136 - ENGLISH

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents