[NETWORK] menu. Panasonic PT-MZ680

Add to my manuals
210 Pages

advertisement

[NETWORK] menu. Panasonic PT-MZ680 | Manualzz

Chapter 4   Settings — [NETWORK] menu

[NETWORK] menu

On the menu screen, select [NETWORK] from the main menu, and select an item from the sub-menu.

Refer to “Navigating through the menu” ( x page 74) for the operation of the menu screen.

[ETHERNET TYPE]

Set the path for transmitting the Ethernet signal.

1) Press as to select [ETHERNET TYPE].

2) Press the <ENTER> button.

f The [ETHERNET TYPE] screen is displayed.

3) Press as

to switch the item.

f The items will switch each time you press the button.

[LAN]

[DIGITAL LINK]

[LAN & DIGITAL LINK]

Select this item when using only the <LAN> terminal to transmit the Ethernet signal.

Select this item when using only the <DIGITAL LINK/LAN> terminal to transmit the Ethernet signal.

Select this item when using the <DIGITAL LINK/LAN> terminal and the <LAN> terminal to transmit the

Ethernet signal.

4) Press the <ENTER> button.

Note f When [ETHERNET TYPE] is set to [LAN], the Ethernet and serial control signals cannot be transmitted via the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) connected to the <DIGITAL LINK/LAN> terminal.

f When [ETHERNET TYPE] is set to [LAN & DIGITAL LINK], the <DIGITAL LINK/LAN> terminal and the <LAN> terminal are connected inside the projector. Do not directly connect the <DIGITAL LINK/LAN> terminal and the <LAN> terminal using a LAN cable. Construct the system so that it is not connected to the same network via the peripherals such as the switching hub or the twisted-pair-cable transmitter.

[DIGITAL LINK]

Make settings and operations related to DIGITAL LINK .

[DIGITAL LINK MODE]

Switch the communication method of the <DIGITAL LINK/LAN> terminal of the projector.

1) Press as to select [DIGITAL LINK].

2) Press the <ENTER> button.

f The [DIGITAL LINK] screen is displayed.

3) Press as

to select [DIGITAL LINK MODE].

4) Press qw

to switch the item.

f The items will switch each time you press the button.

[AUTO]

[DIGITAL LINK]

[LONG REACH]

[ETHERNET]

Switches the communication method automatically to DIGITAL LINK, long reach, or Ethernet.

Fixes the communication method to DIGITAL LINK.

Fixes the communication method to long reach.

Fixes the communication method to Ethernet.

ENGLISH - 137

Chapter 4   Settings — [NETWORK] menu

Possible communication modes l : Communication possible

―: Communication not possible

[AUTO]

Setting

[DIGITAL LINK]

[LONG REACH]

[ETHERNET]

For DIGITAL LINK

For long reach

For Ethernet

Video transfer

(100 m (328'1")) l

― l

Communication possible

Video transfer

(150 m (492'2"))

Ethernet l l

― l l

*1 l l

― l l *1

*1 Communication via a twisted-pair-cable transmitter is not available. Connect the projector to the network directly.

Note

RS-232C l l

― l l

― f

The maximum transmission distance between the twisted-pair-cable transmitter and the projector is 100 m (328'1") for the signal with resolution of 1 920 x 1 200 dots or less. For the signal with the resolution exceeding 1 920 x 1 200 dots, the maximum transmission distance will be 50 m (164'1"). f

The maximum transmission distance when connected with the long-reach communication method is 150 m (492'2"). In this case, the signal that the projector can receive is only up to 1080/60p (1 920 x 1 080 dots, dot clock frequency 148.5 MHz).

f

When the communication method of the twisted-pair-cable transmitter is set to long reach, the projector will connect with long-reach communication method when [DIGITAL LINK MODE] is set to [AUTO]. To connect with the optional DIGITAL LINK Switcher (Model No.:

ET-YFB200G) with the long-reach communication method, set [DIGITAL LINK MODE] to [LONG REACH].

f

Connection will not be made correctly if the twisted-pair-cable transmitter is not supporting the long-reach communication method even if

[DIGITAL LINK MODE] is set to [LONG REACH].

[DIGITAL LINK STATUS]

Display the DIGITAL LINK connection environment.

1) Press as

to select [DIGITAL LINK].

2) Press the <ENTER> button.

f The [DIGITAL LINK] screen is displayed.

3) Press as to select [DIGITAL LINK STATUS].

4) Press the <ENTER> button.

f

The [DIGITAL LINK STATUS] screen is displayed.

[LINK STATUS]

[HDCP STATUS]

[SIGNAL QUALITY]

One of [NO LINK], [DIGITAL LINK], [LONG REACH], or [ETHERNET] is displayed.

One of [NO SIGNAL], [OFF], or [ON] is displayed.

[SIGNAL QUALITY] is a numerical value of the amount of error, and the display color changes to green, yellow, or red depending on that value.

Check the signal quality level while receiving a signal from the twisted-pair-cable transmitter.

f

[MAX]/[MIN]: Maximum/minimum value of the amount of error f

Green ( -12 dB or lower) → normal signal quality level.

f Yellow ( -11 to -8 dB) → caution level that noise may appear on the screen.

f Red ( -7 dB or more) → abnormal level that synchronization is disrupted or not possible to receive.

[DIGITAL LINK MENU]

When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the <DIGITAL LINK/LAN> terminal, the main menu of the connected DIGITAL LINK output supported device is displayed. Refer to the Operating Instructions of the DIGITAL LINK output supported device for details.

Note f

[DIGITAL LINK MENU] cannot be selected when the [NETWORK] menu → [DIGITAL LINK] → [EXTRON XTP] is set to [ON].

[EXTRON XTP]

Make connection setting for the "XTP transmitter" of Extron Electronics.

1) Press as to select [DIGITAL LINK].

138 - ENGLISH

Chapter 4   Settings — [NETWORK] menu

2) Press the <ENTER> button.

f

The [DIGITAL LINK] screen is displayed.

3) Press as to select [EXTRON XTP].

4) Press qw to switch the item.

f The items will switch each time you press the button.

[OFF]

[ON]

Select this item when connecting the optional DIGITAL LINK output supported device (Model No.:

ET-YFB100G, ET-YFB200G) to the <DIGITAL LINK/LAN> terminal.

Select this item when connecting the “XTP transmitter” of Extron Electronics to the <DIGITAL LINK/

LAN> terminal.

Note f

For details of the “XTP transmitter”, visit the website of Extron Electronics.

URL http://www.extron.com/

[WIRED LAN]

Perform the connection setting to use the wired LAN.

1) Press as to select [WIRED LAN].

2) Press the <ENTER> button.

f The [WIRED LAN] screen is displayed.

3) Press as to select an item, and change the settings according to the operation instructions of the menu.

[DHCP]

[IP ADDRESS]

[SUBNET MASK]

[DEFAULT GATEWAY]

[ON]

[OFF]

If a DHCP server exists in the network where the projector is to be connected, obtains the IP address automatically.

If a DHCP server does not exist in the network where the projector is to be connected, set [IP ADDRESS], [SUBNET MASK], and [DEFAULT GATEWAY].

Enter the IP address when a DHCP server is not used.

Enter the subnet mask when a DHCP server is not used.

Enter the default gateway address when a DHCP server is not used.

4) Press as to select [STORE], and press the <ENTER> button.

f

The confirmation screen is displayed.

5) Press qw to select [OK], and press the <ENTER> button.

Note f When using a DHCP server, confirm that the DHCP server is running.

f Consult your network administrator regarding the IP address, subnet mask, and default gateway.

f The network setting is common for the <LAN> terminal and the <DIGITAL LINK/LAN> terminal.

f

[WIRED LAN] cannot be selected when the [NETWORK] menu → [Art-Net] → [Art-Net SETUP] is set to [ON(2.X.X.X)] or [ON(10.X.X.X)].

[PROJECTOR NAME]

Name of the projector can be changed. Enter if a host name is required when using the DHCP server, etc.

1) Press as to select [PROJECTOR NAME].

2) Press the <ENTER> button.

f The [PROJECTOR NAME CHANGE] screen is displayed.

3) Press asqw

to select the character, and press the <ENTER> button to enter the character.

f Up to 12 characters can be entered.

4) Once the entry of the projector name is completed, press asqw

to select [OK], and press the

<ENTER> button.

f To cancel, select [CANCEL].

ENGLISH - 139

Chapter 4   Settings — [NETWORK] menu

Note f

The factory default of the projector name is “Namexxxx”. xxxx is the four digit number assigned for each product.

[NETWORK STATUS]

Display the status of the projector network.

1) Press as

to select [NETWORK STATUS].

2) Press the <ENTER> button.

f

The [NETWORK STATUS] screen is displayed.

[DHCP]

[IP ADDRESS]

[SUBNET MASK]

[DEFAULT GATEWAY]

[DNS1]

[DNS2]

[MAC ADDRESS]

Displays the status of use of DHCP server.

Displays the [IP ADDRESS].

Displays the [SUBNET MASK].

Displays the [DEFAULT GATEWAY].

Displays the address of the preferred DNS server.

Displays the address of the alternate DNS server.

Displays the [MAC ADDRESS] of wired LAN.

Note f

The network setting is common for the <LAN> terminal and the <DIGITAL LINK/LAN> terminal.

[ADMINISTRATOR ACCOUNT]

Set the user name and password of the administrator account.

[PASSWORD POLICY]

Display the policies about the password for the administrator account.

1) Press as

to select [ADMINISTRATOR ACCOUNT].

2) Press the <ENTER> button.

f

The [ADMINISTRATOR ACCOUNT] screen is displayed.

3) Press as to select [PASSWORD POLICY], and press the <ENTER> button.

f The [PASSWORD POLICY] screen is displayed.

PASSWORD POLICY

Reusing passwords is not recommended.

Password cannot be blank.

A password consisting of at least eight half-width characters and contaning characters of at least three of the following four types is recommended.

Uppercase letters

Lowercase letters

Digits

Symbols(~!@#$%^&*()_+\|}{][<>.,/?`)

RETURN

RETURN

Setting the administrator account for the first time

Set the user name and password of the administrator account.

1) Press as to select [ADMINISTRATOR ACCOUNT].

2) Press the <ENTER> button.

f The [ADMINISTRATOR ACCOUNT] screen is displayed.

3) Press as to select [USER NAME], and press the <ENTER> button.

f The [USER NAME] screen is displayed.

f The factory default setting of user name is "dispadmin".

140 - ENGLISH

Chapter 4   Settings — [NETWORK] menu

4) Press asqw to select a character, and press the <ENTER> button.

f

Up to 16 characters can be entered.

5) After entering the user name, press asqw to select [OK], and press the <ENTER> button.

f The [ADMINISTRATOR ACCOUNT] screen is displayed.

6) Press as to select [PASSWORD], and press the <ENTER> button.

f The [PASSWORD] screen is displayed.

7) Press asqw to select a character, and press the <ENTER> button.

f Up to 16 characters can be entered.

f The password cannot be blank.

8) After entering the password, press asqw to select [OK], and press the <ENTER> button.

f The [ADMINISTRATOR ACCOUNT] screen is displayed.

9) Press as

to select [PASSWORD CONFIRM], and press the <ENTER> button.

f The [PASSWORD CONFIRM] screen is displayed.

10) Enter the password entered in Step 7).

11) After entering the password, press asqw to select [OK], and press the <ENTER> button.

f

The [ADMINISTRATOR ACCOUNT] screen is displayed.

12) Press as to select [STORE], and press the <ENTER> button.

f

The confirmation screen is displayed.

13) Press qw to select [OK], and press the <ENTER> button.

Note f For restrictions on character strings that can be set for password, refer to [PASSWORD POLICY] ( x page 140) .

f If the password of the administrator account has not been set, that is, if it is left blank, the network function of this projector cannot be used.

Set a password before using the web control function or the communication control (including operation with application software) via LAN.

f The user name and password of a standard user account without administrator rights can be set on the [Set up password] page ( x page 162) of the web control screen.

Changing settings of the administrator account

Change the user name and password of the administrator account.

1) Press as to select [ADMINISTRATOR ACCOUNT].

2) Press the <ENTER> button.

f The [ADMINISTRATOR ACCOUNT] screen is displayed.

3) Press as

to select [USER NAME] under [CURRENT], and press the <ENTER> button.

f The [USER NAME] screen is displayed.

4) Press asqw

to select a character, and press the <ENTER> button.

f Enter the current user name.

5) After entering the user name, press asqw

to select [OK], and press the <ENTER> button.

f The [ADMINISTRATOR ACCOUNT] screen is displayed.

6) Press as

to select [PASSWORD] under [CURRENT], and press the <ENTER> button.

f The [PASSWORD] screen is displayed.

7) Press asqw to select a character, and press the <ENTER> button.

f

Enter the current password.

8) After entering the password, press asqw to select [OK], and press the <ENTER> button.

f

The [ADMINISTRATOR ACCOUNT] screen is displayed.

9) Press as to select [USER NAME] under [NEW], and press the <ENTER> button.

f The [USER NAME] screen is displayed.

10) Press asqw to select a character, and press the <ENTER> button.

ENGLISH - 141

Chapter 4   Settings — [NETWORK] menu f Enter a new user name.

f Enter the current user name if you do not want to change it.

f

Up to 16 characters can be entered.

11) After entering the user name, press asqw to select [OK], and press the <ENTER> button.

f The [ADMINISTRATOR ACCOUNT] screen is displayed.

12) Press as to select [PASSWORD] under [NEW], and press the <ENTER> button.

f The [PASSWORD] screen is displayed.

13) Press asqw to select a character, and press the <ENTER> button.

f Enter a new password.

f Up to 16 characters can be entered.

f Enter the current password if you do not want to change it.

14) After entering the password, press asqw to select [OK], and press the <ENTER> button.

f The [ADMINISTRATOR ACCOUNT] screen is displayed.

15) Press as to select [PASSWORD CONFIRM] under [NEW], and press the <ENTER> button.

f The [PASSWORD CONFIRM] screen is displayed.

16) Enter the password entered in Step 13).

17) After entering the password, press asqw

to select [OK], and press the <ENTER> button.

f The [ADMINISTRATOR ACCOUNT] screen is displayed.

18) Press as to select [STORE], and press the <ENTER> button.

f The confirmation screen is displayed.

19) Press qw to select [OK], and press the <ENTER> button.

Note f

For restrictions on character strings that can be set for password, refer to [PASSWORD POLICY] ( x

page 140) .

f

The user name and password of the administrator account can also be changed on the [Set up password] page ( x

page 162) of the web control screen.

f

The user name and password of a standard user account without administrator rights can be set on the [Set up password] page ( x

page 162) of the web control screen.

[NETWORK SECURITY]

Make settings to protect the projector from external attacks via LAN and unauthorized use.

Setting the password of the administrator account ( x page 140) is required for setting the [NETWORK

SECURITY] menu.

[COMMAND PROTECT]

Make settings for the connection authentication when using the command control function.

1) Press as

to select [NETWORK SECURITY].

2) Press the <ENTER> button.

f The [NETWORK SECURITY] screen is displayed.

3) Press qw to switch the [COMMAND PROTECT] setting.

[ENABLE]

[DISABLE]

Connect to the projector in protected mode.

The user name and password of the administrator account are required for the connection authentication.

Connect to the projector in non-protected mode.

Connection authentication is not performed.

f The confirmation screen is displayed once the setting is switched.

4) Press qw to select [OK], and press the <ENTER> button.

f The [COMMAND PROTECT] screen is displayed.

5) Press as to select [PASSWORD], and press the <ENTER> button.

142 - ENGLISH

Chapter 4   Settings — [NETWORK] menu f The [PASSWORD] screen is displayed.

6) Press asqw to select a character, and press the <ENTER> button.

f Enter the password of the administrator account.

7) After entering the password, press asqw

to select [OK], and press the <ENTER> button.

f The [COMMAND PROTECT] screen is displayed.

8) Press asqw

to select [OK], and press the <ENTER> button.

Note f

When [COMMAND PROTECT] is set to [DISABLE], connection authentication is not performed, making it vulnerable to threats on the network. Be aware of the risks before making settings.

f

For details on how to use the command control function, refer to "Control commands via LAN". ( x

page 191)

[NETWORK CONTROL]

Set the network control of this projector.

Setting the password of the administrator account ( x page 140) is required for using the network function of the projector.

1) Press as

to select [NETWORK CONTROL].

2) Press the <ENTER> button.

f The [NETWORK CONTROL] screen is displayed.

3) Press as to select an item, and press qw to change the setting.

[WEB CONTROL]

[COMMAND CONTROL]

Set to [ON] to control with the web browser.

Set to [ON] to control with the control command format ( x

page 197) for the <SERIAL/MULTI SYNC

IN> terminal. Refer to “Control commands via LAN” ( x

page 191).

[COMMAND PORT] Set the port number used for command control.

[Crestron Connected(TM)] Set to [ON] to control with Crestron Connected of Crestron Electronics, Inc.

[AMX D.D.]

Set to [ON] to control with the controller of AMX Corporation.

Setting this function to [ON] enables detection through “AMX Device Discovery”. For details, visit the website of AMX Corporation.

URL http://www.amx.com/

4) Press as

to select [STORE], and press the <ENTER> button.

f The confirmation screen is displayed.

5) Press qw

to select [OK], and press the <ENTER> button.

Note f

If the password of the administrator account has not been set, that is, if it is left blank, the network function of this projector cannot be used.

Set a password before using the web control function or the communication control (including operation with application software) via LAN.

[PJLink]

Set the PJLink function to control and monitor the projector using the PJLink protocol.

Setting the password of the administrator account ( x page 140) is required for using the PJLink function of the projector.

Note f If the password of the administrator account has not been set, that is, if it is left blank, the network function of this projector cannot be used.

Set a password before using the web control function or the communication control (including operation with application software) via LAN.

[PJLink PASSWORD]

Set the password for security authentication which is required when connecting to the projector.

1) Press as to select [PJLink].

2) Press the <ENTER> button.

f The [PJLink] screen is displayed.

3) Press as

to select [PJLink PASSWORD], and press the <ENTER> button.

ENGLISH - 143

Chapter 4   Settings — [NETWORK] menu f The [PJLink PASSWORD] screen is displayed.

4) Press as to select [PASSWORD] under [CURRENT], and press the <ENTER> button.

f The [PASSWORD] screen is displayed.

5) Press asqw

to select a character, and press the <ENTER> button.

f Enter the current password.

f The factory default setting of password is blank.

6) After entering the password, press asqw

to select [OK], and press the <ENTER> button.

f The [PJLink PASSWORD] screen is displayed.

7) Press as

to select [PASSWORD] under [NEW], and press the <ENTER> button.

f The [PASSWORD] screen is displayed.

8) Press asqw

to select a character, and press the <ENTER> button.

f Enter a new password.

f Up to 32 alphanumeric characters can be entered.

9) After entering the password, press asqw

to select [OK], and press the <ENTER> button.

f The [PJLink PASSWORD] screen is displayed.

10) Press as to select [PASSWORD CONFIRM], and press the <ENTER> button.

f

The [PASSWORD CONFIRM] screen is displayed.

11) Enter the password entered in Step 8).

12) After entering the password, press asqw to select [OK], and press the <ENTER> button.

f The [PJLink PASSWORD] screen is displayed.

13) Press as to select [STORE], and press the <ENTER> button.

f The confirmation screen is displayed.

14) Press qw

to select [OK], and press the <ENTER> button.

Note f

The PJLink password can also be changed on the [Set up password] page ( x

page 162) of the web control screen.

[PJLink CONTROL]

Set to enable or disable the PJLink protocol control function.

1) Press as

to select [PJLink].

2) Press the <ENTER> button.

f The [PJLink] screen is displayed.

3) Press as

to select [PJLink CONTROL].

4) Press qw to switch the item.

f

The items will switch each time you press the button.

[ON]

[OFF]

Enables PJLink protocol control function.

Disables PJLink protocol control function.

[PJLink NOTIFICATION]

Set to enable or disable the PJLink notification function.

1) Press as to select [PJLink].

2) Press the <ENTER> button.

f The [PJLink] screen is displayed.

3) Press as to select [PJLink NOTIFICATION].

144 - ENGLISH

Chapter 4   Settings — [NETWORK] menu

4) Press qw to switch the item.

f

The items will switch each time you press the button.

[OFF]

[ON]

Disables the PJLink notification function.

Enables the PJLink notification function.

f

If [ON] is selected, proceed to Step 5) .

5) Press as to select [NOTIFIED IP ADDRESS 1] or [NOTIFIED IP ADDRESS 2].

f

Enter the IP address of the computer to notify the status of the projector.

[Art-Net]

Set the Art-Net function.

Setting the password of the administrator account ( x page 140) is required for using the Art-Net function of the projector.

Note f If the password of the administrator account has not been set, that is, if it is left blank, the network function of this projector cannot be used.

Set a password before using the web control function or the communication control (including operation with application software) via LAN.

[Art-Net SETUP]

Make settings to use the Art-Net function.

1) Press as to select [Art-Net].

2) Press the <ENTER> button.

f The [Art-Net] screen is displayed.

3) Press as

to select [Art-Net SETUP].

4) Press qw to switch the item.

f

The items will switch each time you press the button.

[OFF]

[ON(2.X.X.X)]

[ON(10.X.X.X)]

[ON(MANUAL)]

Disables the Art-Net function.

Enables the Art-Net function and sets the IP address to 2.X.X.X.

Enables the Art-Net function and sets the IP address to 10.X.X.X.

Enables the Art-Net function and uses the IP address set in [WIRED LAN].

f Proceed to Step 5) when anything other than [OFF] is selected.

5) Press the <ENTER> button.

f

The [Art-Net SETUP] screen is displayed.

6) Press as to select an item, and press qw to switch the setting.

[NET]

[SUB NET]

[UNIVERSE]

[START ADDRESS]

Enter [NET] to be used when the projector processes Art-Net.

Enter [SUB NET] to be used when the projector processes Art-Net.

Enter [UNIVERSE] to be used when the projector processes Art-Net.

Enter [START ADDRESS] to be used when the projector processes Art-Net.

7) Press as to select [STORE], and press the <ENTER> button.

f The confirmation screen is displayed.

8) Press qw to select [OK], and press the <ENTER> button.

Note f If [ON(2.X.X.X)] or [ON(10.X.X.X)] is selected, IP address is calculated and set automatically.

f The network setting is common for the <LAN> terminal and the <DIGITAL LINK/LAN> terminal.

[Art-Net CHANNEL SETTING]

Set the assignment of the channel.

ENGLISH - 145

Chapter 4   Settings — [NETWORK] menu

For the channel definitions used for controlling the projector with the Art-Net function, refer to “Using Art-Net function” ( x page 187).

1) Press as to select [Art-Net].

2) Press the <ENTER> button.

f The [Art-Net] screen is displayed.

3) Press as

to select [Art-Net CHANNEL SETTING].

4) Press qw to switch the item.

[2]

[USER]

[1]

Uses the channel assignment in standard setting.

Changes the channel assignment.

Uses the channel assignment with DZ21K series compatible.

DZ21K series: DZ21K series, DS20K series, DW17K series, DZ16K series f When [2] or [1] is selected, the function assigned to the channel is displayed by pressing the <ENTER> button.

f When [USER] is selected, proceed to Step 5) .

5) Press the <ENTER> button.

f The [CHANNEL SETUP] screen is displayed.

6) Press as

to select the channel to set, and press qw

to switch the item.

[LIGHT OUTPUT]

[INPUT SELECT]

[LENS POSITION]

Adjusts the amount of light.

Switches the input.

[LENS H SHIFT]

[LENS V SHIFT]

[LENS FOCUS]

[LENS ZOOM]

Moves the lens position.

Adjusts the lens shift in the horizontal direction.

Adjusts the lens shift in the vertical direction.

Adjusts the focus.

[POWER]

[SHUTTER]

[FADE-IN]

[FADE-OUT]

Adjusts the zoom.

Controls the power status.

Controls the shutter function.

Sets the fade-in time.

[SCREEN ADJUSTMENT] Performs screen correction.

[FREEZE] Freezes the projected image, and turns off the audio.

[COLOR]

[TINT]

[RASTER PATTERN]

Sets the fade-out time.

Adjusts the color saturation.

Adjusts the tint.

Displays the raster pattern.

[AUDIO VOLUME]

[ENABLE / DISABLE]

[NONE]

Adjusts the volume.

Enables/disables the control of the projector with the Art-Net function.

No definition f

The setting can be also made by pressing as

to select the channel, pressing the <ENTER> button to display the item list, pressing asqw

to select the item, and pressing the <ENTER> button.

f

Same item cannot be set for multiple channels, except for [NONE].

[Art-Net STATUS]

Display the content of control assigned to each channel and the received data of that channel.

1) Press as to select [Art-Net].

2) Press the <ENTER> button.

f The [Art-Net] screen is displayed.

3) Press as to select [Art-Net STATUS].

4) Press the <ENTER> button.

f The [Art-Net STATUS] screen is displayed

146 - ENGLISH

Chapter 5

Operations

This chapter describes how to use each function.

ENGLISH - 147

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents