CHaPTer 10: Treadmill SPeCifiCaTioNS aNd aSSembly GUide
10.3 aSSembly iNSTrUCTioNS
aTTeNTioN
After assembly and installation is complete, the treadmill will need to be calibrated using the auto-calibration procedure outlined in Section 3.5.
do NoT stand on the belt while the auto-calibration sequence is in progress.
Prior to assembling the treadmill, unpack all of the contents of the box and make sure that all necessary components are present. Review the contents of the hardware package for completeness. Contact Matrix customer service at 866.693.4863 to report any missing items.
aSSembly iNSTrUCTioNS
Please make sure that the power cord is not plugged into the wall outlet while completing the following procedure.
To ensure correct assembly of the treadmill, carefully read and follow these steps:
STeP 1
STeP 2
66
Remove the motor cover(s) and set aside. The motor cover(s) need to be removed to gain access to the motor compartment so that wire harness connections can occur.
Open Black Assembly Bag. Assemble both the left and right console masts to the treadmill base using item 10 socket head cap screw and item 14 washer. Thread the console cable through the right console mast as you attach it.
CHaPTer 10: Treadmill SPeCifiCaTioNS aNd aSSembly GUide
10.3 aSSembly iNSTrUCTioNS - CoNTiNUed
STeP 3
STeP 4
Open White Assembly Bag. Assemble the left and right bracket
(items 20 and 21) to the console base using item 12 socket head cap screw, item 14 flat washer and item 11 socket head cap screw.
Assembly Tip: It is much easier to accomplish this task if the console base is left inside its shipping container.
Open Blue Assembly Bag. Slide the urethane arms over the steel tubes on the console base. Fasten the urethane arms to the steel tubes using item 17 socket head cap screw and item 19 spacer.
67
CHaPTer 10: Treadmill SPeCifiCaTioNS aNd aSSembly GUide
10.3 aSSembly iNSTrUCTioNS - CoNTiNUed
STeP 5 STeP 6
68
Open Red Assembly Bag. Assemble the console base to the console masts using item 15 button head cap screw and item 14 flat washer. Be sure to route the console cables down the console mast through the larger opening in the mast which is closest to the running belt. Make all appropriate wire connections within the motor compartment.
Open Yellow Assembly Bag. Make appropriate wire connections to the faceplate and then assemble to the console base using item
13 socket head cap screw, item 23 lock washers, and item 16 socket head cap screw. Item 16 is a shorter socket head cap screw and gets assembled into the holes closest to the running surface.
All holes applicable to the assembly step can be noted by the embossed arrow next to the hole. See pages 66-67 for detailed instructions on wire connections.
CHaPTer 10: Treadmill SPeCifiCaTioNS aNd aSSembly GUide
10.3 aSSembly iNSTrUCTioNS - CoNTiNUed
J1 and P3 connections at the Motor Control Board with the wire connectors oriented in the correct position (with the tabs pointing up).
J1 and P3 connections correctly made at the Motor Control Board.
5 connections need to be made at the Console. The picture above shows the 5 wire connectors before being connected.
5 connections need to be made at the Console. The picture above shows the 5 wire connectors after being connected.
69
CHaPTer 10: Treadmill SPeCifiCaTioNS aNd aSSembly GUide
10.3 aSSembly iNSTrUCTioNS - CoNTiNUed
2 connections needs to be made to the wires coming out near the power switch. These are an 8 pin connector for CSafe and a coax cable connection.
All of the daughter board connections should already be made.
The picture above shows the daughter board with all the correct connections.
70
The picture above shows a treadmill with the electrical connections completed at the lower end.
CHaPTer 10: Treadmill SPeCifiCaTioNS aNd aSSembly GUide
10.3 aSSembly iNSTrUCTioNS - CoNTiNUed
STeP 7 STeP 8
Open Green Assembly Bag. Install the power cord and assemble item 18 power cord holder with item 22 button head screw. If your hardware pack is missing item 22, check to see if the screws are already assembled on the treadmill.
aSSembly ComPleTe
Assembly is complete, the running belt should be adjusted as needed and the auto calibration sequence must now be run as outlined in sections 3.5 and 3.6
Replace the motor cover(s) and power the treadmill on. The power button is located next to the power cord inlet.
71
