Advertisement
Advertisement
18
Using the dishwasher
Add detergent
Follow the instructions on the detergent packaging.
Too much detergent can result in less effective dishwashing and lead to greater environmental impact.
Detergent compartment
The detergent compartment must be dry when adding detergent.
If powder or liquid dishwasher detergent is used, add a small amount of the detergent to the compartment for prewash detergent.
Prewash detergent Main wash detergent
Press to open Close the lid
NOTE!
Use only dishwasher detergent. Liquid hand-washing detergent must not be used as the foam that forms prevents the dishwasher from operating effectively.
All-in-one detergent
There are many types of all-in-one detergents on the market. Read through the directions for these products carefully.
Activate the TAB setting when using an all-in-one detergent that contains rinse aid.
Dishwasher tablets are not recommended for short programs (less than 75 minutes). Use powder or liquid dishwasher detergent instead.
NOTE!
Optimal washing and drying results are achieved by using normal dishwasher detergent together with separately dispensed rinse aid.
Contact the detergent manufacturer if you have questions about the detergent.
Using the dishwasher
Start/Stop On/Off
Select program Select program mode Select option
On/Off
Open the door and press . Also turn on the water supply valve if it is turned off.
Select program
To select a program, press until the desired program is shown on the display.
Select a program to suit the type of dishes and how dirty they are.
Normal
This program is recommended for daily, regular, or typical use to completely wash a full load of normally soiled dishes, such as plates, serving dishes, cups, and glasses.
Auto
The dishwasher can measure how dirty the dishes are and adjust water consumption and temperature accordingly. When newly installed, the program needs to be run five times before it is fully adapted and can provide the best results.
Intensive
A program with a high temperature for dissolving grease on heavily soiled dishes, such as pans, casserole dishes, and oven dishes. If these dishes do not completely fill the dishwasher, you can add plates and other dishes.
Quick pro 2)
A fast and effective program for slightly dried leftovers. (This program is not intended for burnt food, such as on oven dishes.)
The Auto door open option is important for ensuring the best drying results.
2)
When combined with Speed, the program is shortened (39 minutes).
19
Using the dishwasher
20
Time
The program adapts to the specified running time or finish time. With this program, it is important to choose a time suited to how dirty the dishes are.
Press to set the desired program time.
0:15-0:45
1:00-1:30
2:00-2:30
Lightly soiled dishes
Normally soiled dishes
Heavily soiled dishes
Sanitize
This program is recommended for baby bottles and cutting boards when additional sanitation is required. The temperature is high in the main wash and in the final rinse.
Rinse and hold
Use to rinse dishes while you wait for the dishwasher to become fully loaded.
Self-cleaning
Self-cleaning program for sanitizing the dishwasher tub, spray arms, and spray pipes.
This program should be run (with no dishes in the machine) using regular dishwasher detergent or citric acid. Special dishwasher cleaners are also available in stores. For the removal of limescale deposits, see
in the chapter
Care and maintenance instructions .
Anti-odor 3)
This program prevents bad odors from dirty dishes left in the dishwasher. Only the dishwasher's fan is activated (at regular intervals over a period of 72 hours).
Select program mode
Press to scroll through the available program modes. The symbol is dimly lit in available program modes and glows brighter when a program mode has been activated. (The program modes you can select vary between programs.)
Speed
The program time is shortened, but the dishwasher uses more energy.
Green
The dishwasher uses less energy and water.
Night
Lower noise level during the dishwashing program. The program time is extended.
Heat boost
The higher temperature dissolves grease on very dirty dishes, but the dishwasher consumes more energy and water. The program time is extended.
3)
Activate Odor control in the dishwasher's Settings menu. See the Settings chapter.
Using the dishwasher
Select option
Available options are dimly lit. Select the options ( , ) to activate them. The options glow brighter when activated. (The options you can select vary between programs.)
Auto door open
The dishwasher door opens automatically, which shortens the program time and improves the drying results. Wait until the dishwasher indicates that the program has ended and the dishes have cooled before unloading the dishwasher.
The drying time of the Auto door open option varies (from 5 to 90 minutes) depending on the model, program, and temperature of the final rinse.
The Auto door open option is pre-selected for some programs.
NOTE!
For the best drying results, do not close the door before the drying phase has finished and the machine has automatically switched off.
WARNING!
The dishwasher door must not be blocked or closed when opened automatically. Doing so may damage the door lock mechanism. Wait at least 5 minutes before closing the door.
Delayed start
When you select Delayed start, the dishwasher will start 1-24 hours after you have pressed closed the door.
and
1. Press once to activate Delayed start. Press several times, or hold it in, to set the desired number of hours.
2. Press delay.
and close the door. The timer counts down and the dishwasher starts after the selected
If you want to cancel the Delayed start option, open the door then press and hold seconds.
for three
Start/Stop
Press until the display shows "Program started, close door in 4 sec". This indicates that the dishwasher is ready to start. Close the door properly within four seconds, otherwise the dishwasher will not start.
If the dishwasher is not started or the door is not closed within 2 minutes of the last time the control panel was pressed, the machine switches off.
To remote start the dishwasher, see the chapter
.
Cancel or changing a program
If you want to change the program after starting the dishwasher, open the door then press and hold for three seconds. Add more detergent if the lid of the detergent dispenser has opened. Then choose a new program, press , and close the door within four seconds.
21
Using the dishwasher
Time remaining
Once you have chosen a program, program mode, and options, the time the program took when last used is displayed.
Status light
The status light at the bottom on the dishwasher provides information by means of 3 different colors.
Status light
Blue - Load more
The program has started, but you can still load more dishes.
Red - Do not load
You should not load more dishes (can result in poor dishwashing).
A flashing light indicates that the door has been opened while a program is in progress. If it flashes
when the door is closed, an error has occurred. See the chapter Troubleshooting .
Green - Unload
The dishwashing program is finished. The status light stays on for 30 minutes.
Flashing blue/green
The status light flashes blue/green to indicate that remote start is activated.
If you want to load more dishes
4)
Open the door. The dishwasher stops automatically. Add the dishes. Press within four seconds.
and close the door
If the dishwashing program was remote started, the program will be paused. Press and close the door within four seconds and the interrupted program will continue. You can monitor the dishwasher using the ConnectLife app and remote stop the program, although you will not be able to remote start it again.
WARNING!
If the door is open, "Program paused" is shown on the display. If you want the dishwashing program to continue, press and close the door immediately. If you want to cancel the dishwashing program, press and hold for three seconds.
22
4)
You should not load more dishes if the status light is red.
Using the dishwasher
Power failure
If the dishwasher is turned off due to a power failure when a dishwashing program is running, the program continues when power is restored. If the power is lost during drying, the program is interrupted.
If the dishwashing program was remote started and has not ended, the program will continue once the power is restored. You can monitor the dishwasher using the ConnectLife app and remote stop the program, although you will not be able to remote start it again.
If you open the door for more than 2 minutes during drying, the program will be interrupted.
Once the program has finished
The end of the program is indicated by one short signal from the buzzer. The chapter
describes how to change this function.
Moreover, the end of the program is indicated by the status light turning green.
Once the dishwasher door is opened and the program has finished, "Program done" appears on the display.
The dishwasher switches off automatically after the program ends.
To minimize the risk of leaks, we recommend that you turn off the water supply valve if away from home for an extended period of time.
The best drying results
• Fully load the dishwasher.
• Angle dishes with hollows, such as cups, so that the rinse water will run off. This is also important for plastic items.
• Fill up the rinse aid compartment or increase the rinse aid dosage setting.
• Activate the Auto door open option.
• Allow the dishes to cool before unloading the dishwasher.
Unloading the dishwasher
Hot porcelain is more fragile. Leave the dishes to cool in the dishwasher before unloading them.
Unload the lower basket first to avoid any water drops from the upper basket falling onto the dishes in the lower basket.
23

Public link updated
The public link to your chat has been updated.
Advertisement