Detailed Instructions For Making A Master TV. LG Electronics 26-3DCH-UA, 32-3DCH-UA
Add to my manuals52 Pages
advertisement
TV Camport Auto Sense Operation
The CAMPORT Auto Sense function is enabled when:
1. Installer Menu Item 34, CAMPORT EN is set to 1 AND
2. Installer Menu Item 40, AUTO CAMPORT is enabled (1).
Selectable= Can be accessed with INPUT key, direct access, etc.
Auto Sense= Switches to this input when connector is inserted.
The camport (Front Video) has the highest priority and will override any commands including tuning to the Start Channel.
CAMPORT (Front Video) Functionality Control
Item 34 Item 40
CAMPORT EN AUTO CAMPORT
0 0
0 1
1
1
0
1
Front Video
Operation
Disabled
Disabled
Selectable
Auto Sense
CAMPORT Operation (Stand-Alone)
When Camport Auto Sense is enabled as above, the TV’s source will switch to the front video whenever a plug is inserted into any of the front panel video inputs (either composite Video or
S-Video).
When the plug is removed, the TV will switch back to the previous channel or input source that the TV was using before the plug was inserted. However, if any direct access to an RF channel or Aux channel is requested while the camport is active, then, when the camport plug is removed, the TV will switch to the last requested channel. Source changes using any Source
Keys (INPUT) are ignored. Channel Up, Channel Down and
Flashback Commands are not direct access tuning commands and they are also ignored.
Previous State Operation
Before Inserting While CAMPORT
CAMPORT
Aux or RF Channel
Is Active
None
Direct Access Aux or RF Channel
Aux or RF Channel Ch Up/Down,
Flashback and TV/AV Keys
State
Upon Removal
Of CAMPORT
Previous Aux or RF Channel
Last Requested
RF or Aux Channel
Previous Aux or RF Channel
CAMPORT Operation (PPV)
The operation will be similar to that of the Stand-Alone mode.
However, the PPV providers may send different commands to the TV for the same user commands. For instance, some providers will always send a direct tune command when it receives a channel up/down or a flashback command while other PPV providers will just send a key command.
Previous State Operation
Before Inserting While CAMPORT
CAMPORT
Aux or RF Channel
Is Active
None
Aux or RF Channel
Aux or RF Channel
Direct Access
Ch Up/Down,
Flashback and TV/AV Keys
State
Upon Removal
Of CAMPORT
Previous Aux or RF Channel
Last Requested RF or Aux Channel
Last Requested
Channel if PPV translates it to direct access tuning command. Otherwise, goes to Previous Aux or RF Channel
P A G E 4 4
206-4071
TV Aux Input Configuration
DIRECT ACCESS
Tuning
TV
OLD_OCV
=0
OLD_OCV=
1
Source Input Source Mode Number
ENABLE
Installer Menu
Labeling
MPI DATA
MPI DATA
STATUS TYPE
0x41 SOURCES
ENABLED (R/W)
DATA STATUS
TYPE 0xD2
CURRENT AV
SOURCE (R)
DATA
STATUS
TYPE 0X0D
START AUX
SOURCE
AUX SOURCE
ASSIGNMENT
(R)
Value Labeling Value Labeling
130
131
133
90
91
93
Video2 (Side) CV/SVIDEO
Video1 (Rear) CV/SVIDEO
HDMI1/DVI
DTV
PC
DTV
34
39
35
35
87
CAMPORT_EN 0x01
Video Front
(Camport)
REAR_AUX_EN 0x02
COMPPORT EN = 1 0x08
COMPPORT EN = 2 0x08
Rear Video
(Aux)
Front
Computer
Front
Computer
REAR RGB EN = 1 0x10
SVGA Rear
Computer
0
1
3
3
4
Video Front
(Camport)
0 (VIDE0)
Rear Video
(Aux)
Front
Computer
Front
Computer
0 (VIDE0)
0 (VIDE0)
2
(COMPUTER)
SVGA Rear
Computer
0 (VIDE0)
2
1
3
3
4
134 94 RGB
136 96 Component
PC 87
38
REAR RGB EN = 2 0x10
SVGA Rear
Computer
YPrPb EN 0x40
Y/UV
Component
4
6
SVGA Rear
Computer
2
(COMPUTER)
Rear
Y/PrPb
Component video
0 (VIDE0)
4
6
Power Savings Setup
Installer Item 118 Power Saving: set to 001, enabled (Default).
Installer Item 099 Backlighting: value set as shown below. (Default value is 200)
Item 099
Backlighting
(Static)
100
90
80
70
60
50
40
30
20
10
1
Picture Power
Lumin.
Consumption
217
202
188
172
157
128
124
109
95
78
64
(Watts)
122
114
109
102
95
89
82
75
69
62
56
Power
Savings
Rating
0 %
7 %
11 %
76 %
22 %
27 %
33 %
39 %
43 %
49 %
54 %
Note: Values are results of controlled experiments under laboratory conditions.
Item 099
Backlighting
(Dynamic)
200
190
180
170
160
150
140
130
120
110
101
Picture Power
Lumin.
Consumption
130
123
117
109
101
94
86
79
72
63
57
(Watts)
86
83
80
76
74
70
67
64
61
58
56
Power
Savings
Rating
30 %
32 %
34 %
38 %
39 %
43 %
45 %
48 %
50 %
52 %
54 %
206-4071
P A G E 4 5
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 6 Warnings
- 8 Important Safety Instructions
- 9 Table of Contents
- 12 Installer Overview
- 13 TV Overview
- 14 Typical Installer’s Remote Control
- 16 Rear Connections Panel
- 18 MPI Card Slot / PPV Card Installation
- 19 Vesa Standard TV Mounts
- 20 Pillow Speaker Connections
- 21 Features Setup Menus Overview
- 22 Channel Menu
- 23 Picture Menu
- 24 Audio Menu
- 25 Time Menu
- 26 Option Menu
- 27 Lock Menu
- 31 Channel Banks Setup
- 32 USB Software Upgrades
- 33 USB Learn / Teach
- 34 TLL-1100A Cloning Instructions
- 37 LT2002 Cloning Instructions
- 43 Installer Menus
- 44 Detailed Instructions For Making A Master TV
- 46 Clonable Menu Features Chart
- 46 Checking Software Version
- 47 USB Cloning Troubleshooting
- 48 TV Camport Auto Sense Operation
- 49 TV Aux Input Configuration / Power Savings Setup
- 50 Troubleshooting
- 51 Cloning Troubleshooting
- 52 Channel Banks Setup Troubleshooting