FIGURES. Fujitsu C141-E090-02EN

Add to My manuals
189 Pages

advertisement

FIGURES. Fujitsu C141-E090-02EN | Manualzz

FIGURES

1.1

2.1

2.2

2.3

3.1

3.2

3.3

3.4

3.5

3.6

3.7

3.8

3.9

page

Current fluctuation (Typ.) when power is turned on....................................................... 1 - 7

Disk drive outerview ...................................................................................................... 2 - 1

1 drive system configuration .......................................................................................... 2 - 3

2 drives configuration..................................................................................................... 2 - 3

Dimensions..................................................................................................................... 3 - 2

Orientation...................................................................................................................... 3 - 3

Limitation of side-mounting........................................................................................... 3 - 4

Mounting frame structure ............................................................................................... 3 - 4

Surface temperature measurement points ....................................................................... 3 - 5

Service area .................................................................................................................... 3 - 6

Connector locations ........................................................................................................ 3 - 7

Cable connections........................................................................................................... 3 - 8

Power supply connector pins (CN1)............................................................................... 3 - 9

3.10

Cable configuration ........................................................................................................ 3 - 10

3.11

Cable type detection using CBLID- signal

(Host sensing the condition of the CBLID- signal) ........................................................ 3 - 11

3.12

Cable type detection using IDENTIFY DEVICE data

(Device sensing the condition of the CBLID- signal)..................................................... 3 - 11

3.13

Jumper location .............................................................................................................. 3 - 12

3.14

Factory default setting .................................................................................................... 3 - 13

3.15

Jumper setting of master or slave device ........................................................................ 3 - 13

3.16

Jumper setting of Cable Select ....................................................................................... 3 - 14

3.17

Example (1) of Cable Select ........................................................................................... 3 - 14

4.4

4.5

4.6

5.1

3.18

Example (2) of Cable Select ........................................................................................... 3 - 14

4.1

Head structure................................................................................................................. 4 - 2

4.2

4.3

MPE3xxxAH Block diagram.......................................................................................... 4 - 5

Power-on operation sequence ......................................................................................... 4 - 7

5.2

5.3

Block diagram of servo control circuit ........................................................................... 4 - 13

Physical sector servo configuration on disk surface ....................................................... 4 - 14

72 servo frames in each track ......................................................................................... 4 - 17

Execution example of READ MULTIPLE command .................................................... 5 - 19

Read Sector(s) command protocol.................................................................................. 5 - 68

Protocol for command abort ........................................................................................... 5 - 69

C141-E090-01EN xi

5.4

5.5

5.6

5.7

WRITE SECTOR(S) command protocol........................................................................ 5 - 70

Protocol for the command execution without data transfer ............................................ 5 - 71

Normal DMA data transfer ............................................................................................. 5 - 73

Ultra DMA termination with pull-up or pull-down ........................................................ 5 - 84

5.8

5.9

PIO data transfer timing.................................................................................................. 5 - 85

Multiword DMA data transfer timing (mode 2) ............................................................. 5 - 86

5.10

Initiating an Ultra DMA data in burst............................................................................. 5 - 87

5.11

Sustained Ultra DMA data in burst................................................................................. 5 - 90

5.12

Host pausing an Ultra DMA data in burst ...................................................................... 5 - 91

5.13

Device terminating an Ultra DMA data in burst ............................................................. 5 - 92

5.14

Host terminating an Ultra DMA data in burst................................................................. 5 - 93

5.15

Initiating an Ultra DMA data out burst........................................................................... 5 - 94

5.16

Sustained Ultra DMA data out burst............................................................................... 5 - 95

5.17

Device pausing an Ultra DMA data out burst................................................................. 5 - 96

5.18

Host terminating an Ultra DMA data out burst............................................................... 5 - 97

5.19

Device terminating an Ultra DMA data out burst ........................................................... 5 - 98

6.4

6.5

6.6

6.7

5.20

Power-on Reset Timing .................................................................................................. 5 - 99

6.1 Response to power-on .................................................................................................... 6 - 2

6.2

6.3

Response to hardware reset ............................................................................................ 6 - 3

Response to software reset.............................................................................................. 6 - 4

6.8

6.9

Response to diagnostic command .................................................................................. 6 - 5

Address translation (example in CHS mode).................................................................. 6 - 7

Address translation (example in LBA mode) ................................................................. 6 - 8

Sector slip processing ..................................................................................................... 6 - 11

Alternate cylinder assignment ........................................................................................ 6 - 12

Data buffer configuration ............................................................................................... 6 - 13 xii C141-E090-01EN

advertisement

Related manuals

Download PDF

advertisement

Table of contents