advertisement
NOTE:
B You can also turn off the power by pressing the POWER button twice or by holding down it for at least 0.5 seconds.
B When the projector is in standby mode (the power indicator on the projector is illuminated red), the projector will still draw a maximum 7 W of power, even when the cooling fan has stopped.
(PT-L735NTE only)
B When the WEB STANDBY is set to “ON”, the cooling fan operates and the power indicator on the projector flashes slowly in red and the projector draw a maximum 30 W of power. (page 48)
B Do not turn off the power while the SD card is being accessed and “SD
CARD IN USE.” is displayed on the screen.
Power indicator
Power indicator status
Red
Green
Orange
Illuminated
Flashing slowly
Flashing
Illuminated
Illuminated
Flashing
Projector status
The projector is in standby mode and image projection is possible by pressing the POWER button.
WEB STANDBY in the NETWORK menu is set to
“ON”. The projector can be controlled with personal computers by means of a wireless network.
(The cooling fan is operating.) : PT-L735NTE only.
The projector is preparing for projection after the power is turned on while the power indicator is illuminated red. (After a short period, a picture will be projected.)
A picture is being projected.
The lamp is cooling down after the power is turned off. (The cooling fan is operating.)
The projector is preparing for projection after the power is turned on while the power indicator is illuminated orange. (After a short period, a picture will be projected.)
RGB INPUT indicator
RGB INPUT indicator status
Illuminated during standby mode
Illuminated during projection
Projector status
A signal is being input to either the RGB1 IN or
RGB2 IN connector.
A signal is being input to the connector selected using the input select buttons.
26-E
NGLISH
Correcting keystone distortion and automatic positioning (AUTO SETUP)
This projector detects its degree of tilt and the input signal. Keystone distortion and the position of the image can then be corrected automatically in accordance with the input signal.
Press the AUTO SETUP button.
(When the projected image has caused keystone distortion)
RGB LASER
VIDEO MENU
PAGE
Screen
Projected image
B Automatic positioning will be carried out.
[
Projector control panel
If you press the AUTO SETUP button, the items given in the table below will be set automatically in addition to keystone distortion being corrected. The setting details change according to the signal which is being input.
Input signal
RGB signals
Contents set up automatically
POSITION, DOT CLOCK, CLOCK PHASE
(If the dot clock frequency is 100 MHz or higher, the DOT
CLOCK and CLOCK PHASE will not be set automatically.)
Page
40,
41
NOTE:
B If the edges of the projected picture are indistinct, or if a dark picture is being projected, the automatic setup processing may stop automatically before it is complete. If this happens, project a different picture and then press the AUTO
SETUP button once more, or make the above adjustments manually.
B Set AUTO KEYSTONE in the OPTION menu to “OFF” to prevent any deterioration of the picture as a result of keystone correction. (Refer to page 45.)
B Keystone distortion may not be corrected enough depending on the adjustment of the zoom ring. In this case, adjust the KEYSTONE option. (Refer to page 41.)
E
NGLISH
-27
Turning off the picture and sound momentarily (SHUTTER)
The shutter function can be used to momentarily turn off the picture and sound from the projector when the projector is not being used for short periods of time, such as during breaks in meetings or when carrying out preparation. The projector uses less power in shutter mode than it does in normal projection mode.
R-CLICK
ENTER
Press the SHUTTER button.
B The picture and sound will be turned off.
B Press any button on either the projector or remote control unit to return to normal operating mode.
FUNC1 STD
Computer
Projector
Pausing a picture (FREEZE)
Press the FREEZE button.
R-CLICK
ENTER
Still picture
FUNC1 STD
Computer Projector
28-E
NGLISH
B The picture being projected will be paused.
B Press the FREEZE button again to cancel the still picture.
Enlarging the picture (D.ZOOM)
Press a D.ZOOM +/- button.
POWER AUTO SETUP
RGB LASER
VIDEO MENU
PAGE
B The picture will then be enlarged to 1.5
times the normal size.
[
R-CLICK ENTER
FREEZE SHUTTER
FUNC1 STD
The remote control unit functions during D.ZOOM (digital zoom)
Use the F,G,IandHbuttons to move the enlarged area which you want to project.
Use the D.ZOOM +/- buttons to change the enlargement ratio.
Press the MENU button to return to the normal screen.
NOTE:
B The enlargement ratio can be changed within the range of x1 to x4, by 30 steps.
B If the type of signal being input changes while the digital zoom function is being used, the digital zoom function will be cancelled.
Adjusting the volume (VOLUME)
FREEZE SHUTTER
Press the VOLUME +/- button.
B Press the + button to raise the volume.
B Press the - button to lower the volume.
FUNC1 STD
NOTE:
B You can also select “VOLUME” from the
AUDIO menu to adjust the volume.
Computer
Projector
E
NGLISH
-29
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 1 safety
- 5 Accessories
- 6 Before use
- 13 Inserting the wireless card
- 14 Setting-up
- 16 Connections
- 18 control unit
- 19 Turning on the power
- 21 Turning off the power
- 23 and automatic positioning
- 24 momentarily
- 24 Pausing a picture
- 25 Enlarging the picture
- 25 Adjusting the volume
- 26 control unit
- 28 On-screen menus
- 33 Adjusting the picture
- 21 Adjusting the position
- 23 Audio adjustment
- 23 Option settings
- 25 Network setup
- 25 SD card setup
- 25 function
- 27 the air filter
- 28 Replacing the lamp unit
- 30 Before calling for service
- 30 Cleaning and maintenance
- 31 Specifications
- 32 Appendix
- 32 Dimensions