Installation Tab. Sony SNC-DH180, SNC-CH140, CH280, SNC-DH140, CH240, Ipela SNC-CH180, Ipela SNC-CH240, Ipela SNC-CH280, DH280, CH180

Superimpose format

Click Edit to edit the content to superimpose over each display position.

Only one Date and one Camera ID can be specified for the Superimpose format.

You can set the content to superimpose in the “Lower left”, “Lower right”, “Upper left”, “Upper right”,

“Center”, “Top” and “Bottom” parts, respectively.

However, if you specify the “Top”, superimposed content will not appear on the upper left or upper right.

Similarly, if you specify “Bottom”, superimposed content will not appear on the lower left or lower right.

If the Lower left/Lower right or Upper left/Upper

right are displayed at the same time, the maximum image size that can be used for a logo is 624 × 120.

Click Date & Time, Camera ID, Codec, Zoom,

Camera direction or Event to insert the corresponding tag into the string.

Display sample: Lower left

OK/Cancel

See “Buttons common to every menu” on page 32.

Installation Tab

You can perform settings related to installation.

Maximum image size

SNC-CH140/CH180/DH140/DH180

1280 × 720: Image will have an aspect ratio of 16:9, and an image size up to 1280 × 720 can be specified for the video codec.

1280 × 1024: Image will have an aspect ratio of 5:4, and an image size up to 1280 × 1024 can be specified for the video codec.

SNC-CH240/DH240/CH280/DH280

1920 × 1080: Image will have an aspect ratio of 16:9, and an image size up to 1920 × 1080 can be specified for the video codec.

1920 × 1440: Image will have an aspect ratio of 4:3, and an image size up to 1920 × 1440 can be specified for the video codec.

Notes

• The camera restarts when the Maximum image size is changed. It takes about 2 minutes.

• The settings below are changed when the Maximum image size is changed.

– Camera menu-privacy mask tab: returns to the factory setting.

– Camera menu-video codec tab: returns to the factory setting except:

SNC-CH140/CH180/DH140/DH180

– Image size of image1: to be 1280 × 720 when set to 1280 × 720, or 1280 × 1024 when set to

1280 × 1024.

– Frame rate of image1: to be 30fps when set to

1280 × 720, or 20fps when set to 1280 × 1024

SNC-CH240/DH240/CH280/DH280

– Image size of image1: 1920 × 1080 (when set to

1920 × 1080), or 1920 × 1440 (when set to

1920 × 1440).

– Frame rate of image1: 30fps (when set to

1920 × 1080), or 20fps (when set to 1920 × 1440).

– Preset position menu: returns to the factory setting.

– Alarm buffer menu: returns to the factory setting.

– Event detection menu- motion detection tab: returns to the factory setting except:

SNC-CH140/CH180/DH140/DH180

– Maximum detection size of motion diction: to be width of 1280 and height of 720 when set to

1280 × 720, or 1280 and height of 1024 when set to 1280 × 1024.

– Maximum detection size of VMF: to be width of

1280 and height of 720 when set to 1280 × 720 or

1280 and height of 1024 when set to 1280 × 1024.

SNC-CH240/DH240/CH280/DH280

– Maximum detection size of motion detection: width 1920, height 1080 (when set to

1920 × 1080), or 1920 and 1440 (when set to

1920 × 1440).

– Maximum detection size of VMF: width 1920, height 1080 (when set to 1920 × 1080) or 1920 and 1440 (when set to 1920 × 1440).

• Once the maximum image size has been changed, full panorama image will not be displayed in the optimum aspect ratio. To return to the optimum aspect ratio, capture the full image again in Initial tab - Capture

full image.

Video out

You can configure the output setting for the analog image output terminal of the camera. Select On to output an NTSC or PAL signal.

Note

The output signal format is determined according to the setting of the camera’s NTSC/PAL switch.

Configuring the System — System Menu

37