Storage. Toshiba SATELLITE A60, a65

Add to my manuals
262 Pages

advertisement

Storage. Toshiba SATELLITE A60, a65 | Manualzz

3 Diagnostic Programs 3.7 Storage

3.7 Storage

Subtest 01 HDD

This test item runs on IDE hard disks. It checks the functions and performance of IDE hard disk.

1. Sequential/Random R/W

This test item is to check the HDD’s Read/Write function through data writing and reading to HDD.

This test item needs user to submit the parameters:

IDE HDD Test Range-- Specify the test coverage range of IDE HDD. If user chooses Total Size, it means that the whole IDE HDD will be tested. Although user can input the parameter into other select box, but the selected result is invalid. If user chooses Special Size, the test of IDE HDD will be taken according to the coverage range that user chooses or time.

LBA Start, LBA End--Specify the start and end byte in LBA (Large Block

Address).

Percent—Specify the coverage rate in percentage of the total disk.

Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested.

Time Limit(m): Choose or Input the time (minute) of the defined range of the total disk to be tested.

Test Mode —Choose test mode from the following options:

40 dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual

3.7 Storage 3 Diagnostic Programs

(1) Read & Write –Write data on the disk, then read it out and compare the two value;

(2) Read Verify —Read data only;

(3) Unprotected Write—Write data on the disk without backup original data.

Option—Select sequential test or random test

2. Sequential/Random Seek

The test item is to check the correctness of the HDD’s sector’s seeking function.

This test item involves the following parameters:

IDE HDD Test Range—is same as the description of the upper item.

LBA Start, LBA End-- specify start and finish byte in LBA(Large Block

Address);

Option-- Select sequential test or random test;

Percent -- Specify the coverage rate in percentage of the total disk.

Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested;

Time Limit(m): Choose or Input the time (minute) of the defined range of the total disk to be tested.

3. Performance

Check the HDD’s seeking speed and transfer the data rate.

4. Controller Check

dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual 41

3 Diagnostic Programs 3.7 Storage

Check the HDD controller’s status, including HDD interrupt and unexpected interrupt.

5. Diagnostic Read/Write

This test item is a quick test to verify whether the HDD could be correctly accessed and the user could specify the percentage in the below dialog.

Percent (1-100)-- Specify the coverage rate in percentage of the total disk.

Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested;

Time Limit(m): Choose or Input the time (minute) of the defined range of the total disk to be tested;

6. SMART Test

SMART stands for Self-Monitoring, Analysis and Reporting Technology.

SMART test will compare the attribute values with the threshold value in the

HDD’s controller to confirm whether there is any failure in the HDD

Subtest 02 ODD

The ODD test runs on IDE CDROM/DVD-ROM & CD-RW. It will check the ODD driver’s functionality and performance.

1. Controller Test

Check the CDROM controller’s status.

2. Data Transfer Rate

Check the data transfer rate of the ODD drive. It will read data from the ODD disc and calculate the data transfer rate. This test needs a data CD.

3. Data CD Butterfly Seek

42 dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual

3.7 Storage 3 Diagnostic Programs

Check the seek function of the ODD drive. It will perform a serial of seeking operations. First, locate the minimum LBA address, then the maximum, the subminimum, the sub- maximum and meet at center point. This test needs a data CD.

4. Data CD Random Seek

Check the random seek function of ODD drive. Random access will reflect the performance of the heads’ random movement and seek. It tests for 1000 times.

5. Data CD Sequence Seek

Check the sequential seek function of ODD drive. Perform location test to CD-

RW under LBA mode with the location address increasing in sequence.

6. Tray Eject Test

Check the eject function of the ODD. It will eject the ODD and ask the user to confirm if the operation succeeds.

dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual 43

3 Diagnostic Programs 3.8 Video

3.8 Video

This test item tests the video by:

1. displaying the figures in different graphic modes.

2. displaying the property and color of the characters in different text modes.

User will confirm whether each video mode works normally by judging whether the display is correct. It checks whether the video memory works normally by writing data into the video memory, then reading it out and comparing the two value.

Subtest 01 Text Mode

1. Character Test

Tests two types of font patterns.

Font 9*14

Font 9*16

It requires the user to check whether all characters of each font type displayed correctly by answering the questions prompted on screen. It will be displayed as follows:.

2. Text Attribute

This test item is to check whether the text attribute of normal, hi- intensity, inverse, and blinking in VGA text mode could be correctly displayed on the screen.

44 dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual

3.8 Video 3 Diagnostic Programs

It would display the below texts of the different attributes in the screen:

1. Text in normal attribute;

2. Text in blinking normal attribute;

3. Text in inverse attribute;

4. Text in blinking inverse attribute;

5. Text in hi- intensity attribute;

6. Text in blinking hi- intensity attribute;

Users need to check whether all texts displayed correctly in the above six attributes and key in the answer ‘Y’ or ‘N’ to the prompts ‘Is this display OK?

[Y/N<Enter=Y> ]’.

Below is the test screen of Text Attribute.

3. Text Page Selection

This test item is to check whether the video memory could be correctly written and read in VGA text mode. According to the comparison of written data with read data, the program would report PASS or FAIL.

dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual 45

3 Diagnostic Programs 3.8 Video

4. Text Color

This test item is to check whether all 16 colors foreground and all 8 colors background works normally in VGA text mode.

The bit4-6 of the attribute byte of a character defines 8 background colors (black, blue, green, cyan, red, brown, magenta, and light gray), and the bit0-3 defines 16 foreground colors (dark gray, light blue, light green, light cyan, light red, light magenta, yellow, and white besides the above 8 colors).

In the test, user is required to respond according to the instruction in the screen.

5. 80 * 25 Text Mode

This test item is to check whether 80*25 Text Mode works normally.

46 dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual

3.8 Video 3 Diagnostic Programs

In the test, user is required to respond according to the instruction in the screen.

Subtest 02 640 * 480 VGA Mode

This test item is to check whether 680*480 VGA Text mode works normally.

In the test, user is required to respond according to the instruction in the screen.

Subtest 03 VESA Video Modes

This test item is to check whether all the video modes supported by the video card works normally.

In the test, user is required to respond following the instruc tion in the screen.

dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual 47

3 Diagnostic Programs

1. 640X480 Video Modes Test

3.8 Video

p

2. 800X600 Video Modes Test

3. 1024X768 Video Modes Test

4. 1280 x1024 Video Modes Test

5. 1400 X1050 Video Modes Test

6. 1600 X1200 Video Modes Test

Subtest 04 VESA Video Memory

This test item is to check whether VESA video memory could be correctly accessed (write data & read data). Below is the test item’s parameter dialog window:

48 dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual

3.8 Video 3 Diagnostic Programs

Subtest 05 DDC Test

This test item is to check whether the video card and the video display support

DDC (Display Data Channel).

Subtest 06 AGP Test

This test item is to report the system’s Accelerated Graphics Port status and check whether AGP registers works normally.

Subtest 07 LCD Panel Test

This test item is to check whether there is any fault in its resolution by displaying the RGB gradient color screens.

dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual 49

3 Diagnostic Programs 3.8 Video

Subtest 08 Register Test

This test item is to check whether the registers of the video adapter works normally.

Subtest 09 Color Purity Test

This test item is to check whether the system (the video adapter and the display) could display the purity color of red, green, blue, black and white.

In the test, user is required to respond according to the instruction in the screen.

Subtest 10 Direct Color Test

This test item is to check the video adapter’s composing ability of direct color in high and true color mode.

In the test, user is required to respond according to the instruction in the screen.

50 dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual

3.8 Video 3 Diagnostic Programs

Subtest 11 DAC/Palette Address

This test item is to check the function of DAC registers and Palette registers.

In the test, user is required to respond according to the instruction in the screen.

dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual 51

3 Diagnostic Programs 3.8 Video

Subtest 12 BitBlt Engine Test

This test item is to check whether the BitBlt engine works normally.

BitBlt is the abbreviation of ‘Bit Block Translate’, that means the copy of data block for 3 types, from video memory to video memory, from video memory to system memory, and from system memory to video memory.

What should be done is to write the data of the type of BitBLT operation and the location of BitBLT source area and destination area into the BitBLT registers, and all those operations will be completed automatically by BitBLT engine with minimum CPU intervention.

52 dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual

3 Diagnostic Programs 3.9 Communication

3.9 Communication (COMM)

Subtest 01 LPT

This test item is to check whether there is open or short circuit issue in the external pins by looping back the external pins, controlling the voltage of each data pin, control pin and status pin.

The test requires an external connector to insert into the tested LPT port. Below is the connector's description.

Fixture Description:

(9) + PD7

(8) + PD6

(7) + PD5

(6) + PD4

(5) + PD3

(15) -ERROR

(14) -AUTFD

(13)

(16) -PINIT

(1) - STRO BE

(4) + PD2

(3) + PD1

(2) +PD0

Note: (1)~(17) -------- Pin number

PD0~ PD7--------Data Line

(10) - ACK

(12) + PE

(17) - SLIN

(11)+ BUSY

Status Line -------- –ERROR(S3), +SELECT(S4), –ACK(S6), +PE(S5), +BUSY(S7)

Control Line -------- –AUTFD(C1), –PINIT(C2), -STROBE(C0), –SLIN(C3)

1. Register Check

Check whether the data register and control register works normally.

2. IRQ Check

Check whether LPT interrupt works normally.

3. External Loop back

Check whether there is open or short circuit issue.

4. ECP Mode

54 dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual

3.9 Communication 3 Diagnostic Programs

Check whether it supports ECP (Extended Capabilities Port) feature.

Subtest 02 IrDA

This test item is divided into Fast IR (FIR) and Slow IR (SIR). FIR supports the transfer rates of 0.576Mbps, 1.152Mbps and 4.000Mbps; SIR supports the transfer rates of 2400bps, 4800bps, 9600bps, 19200bps, 38400bps, 57600bps, and 115200bps.

The unit under testing (UUT) is called Slave. It requires a unit whose IrDA works normally(that is called Master) for transferring data between Slave and Master. Below is the parameter dialog window of IrDA test.

Connect Timeout: Define the time that slave connecting to master (in seconds);

Test Timeout: Define the time that testing each transfer rate(in seconds);

SIR Test: Choose the transfer rates to be checked in Slow IR;

FIR Test: Choose the transfer rates to be checked in Fast IR.

Below are the operation steps:

? Prepare a Master whose IrDA works normally, then run the test item in

‘Comm/IrMaster’ under Diagnostics menu; the master stays here to wait for slave requesting.

? Prepare a slave. User should choose the test item ‘Comm/IrSlave’ and set parameters.

Below is the Slave Testing window.

dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual 55

3 Diagnostic Programs 3.9 Communication

Below is the Master Testing window:

Subtest 03 LAN Card

This test item is to check whether the module can detect the existence of the network card and display its related information.

1. Device ID Detection

Detect the device ID of the network card.

2. Vendor ID Detection

56 dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual

3.9 Communication 3 Diagnostic Programs

Detect the vendor ID of the network card.

3. MAC Address Detection

Detect the MAC address of the network card.

Subtest 04 1394

GUID Detection

This test item is used to read and display GUID from 1394 register.

dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual 57

3 Diagnostic Programs

3.10 Peripheral

Subtest 01 Keyboard

This test item is to check whether the keyboard works normally.

1. Keyboard Data Line Test

Check whether the keyboard data line works normally.

2. Keyboard Led Test

Check whether the keyboard led works normally.

3.10 Peripheral

3. Keyboard Clock Line Test

Check whether the keyboard clock line works normally.

Subtest 02 Mouse Test

Check whether the point devices work normally.

1. Touch Pad

Before test Touch Pad’s function, user should set a timeout time at below screen:

58 dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual

3.10 Peripheral 3 Diagnostic Programs

At the below screen of Touc h Pad test, user can press the left button, right button, and move the mouse to verify its functions for times, and the test will end either by user break or test time is out.

dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual 59

3 Diagnostic Programs 3.11Error Codes and Description

3.11 Error Codes and description

The format of ‘Error Code’ is ‘ddxxee’, and ‘dd’ is the device ID (1~2 chars), ‘xx’ is test function

ID of device (2 chars), ‘ee’ is the error code of device (2 chars); the range of error code is from 01 to 99 in each device (the common error codes in all device are set to 99 and spanned).

Device

Error

Code

Description ddxx ee Common Error

01xx

02xx

Cause Action

94 Interactive Mode Needed

The test is not under interactive mode.

Check whether the interactive test mode is adopted.

CPU

01

02

03

04

05

CPU General Function

Error

CPU Arithmetic Error

CPU Logic Error

CPU Type Error

CPU Speed Error

The CPU General Function register is damaged.

Replace the CPU.

The CPU Arithmetic Register is damaged.

As above.

The CPU Logic Register is damaged.

The CPU Type is not supportable.

As above.

Check whether the CPU is Intel

CPU.

The CPU speed differs from the expected value.

Check the CPU speed and the set expected speed.

06

NPU General Function

Error

07 NPU Interrupt Error

08

10

11

CPU Information Error

Does not Support CPU

Speedstep

CPU Speedstep Power

Change Error

The NPU arithmetic unit is damaged.

The NPU is damaged.

Information of the CPU cannot be acquired.

09 Protected Instruction Error The CPU is damaged.

The CPU does not support

Speedstep.

Replace the CPU.

As above.

Check whether the CPU is Intel

CPU.

Replace the CPU.

Check whether the power change mode is correct.

The power mode is not correctly changed.

As above.

12

21

01

CPU Speedstep Speed

Change Error

MMX Test Error

Memory

Read Error

The CPU frequency cannot alternate normally with the change of power mode.

The CPU MMX register is damaged.

The ROM BIOS has Physical problems.

Confirm with the same type CPU.

Replace the CPU.

Test this unit on multiple machines.

60 dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual

3.11Error Codes and Description 3 Diagnostic Programs

03xx

02

03

Write-Protect Error

Base Memory Error

Address

The ROM BIOS has Physical problems.

As above.

The test pattern read out from the base memory is different from Test this memory chip on the one that has been written in multiple machines. this address.

04 (XMS)Memory Problem

The test pattern read out from the extension memory is different

As above. from the one that has been written in this address.

05 (XMS) Out Of Range Wrong parameters setup.

06 Address Test Error

Interference between different address channels.

Check and reset the parameters.

Test this memory chip on multiple machines.

07 Toggle Bit Error Errors with the timer chip. As above.

08

09

12

14

01

04

05

Interval Error

L1 Cache test Error

Data Bus Error

Speed Error

Board

DMA Test Error

Interval Timer Error

Periodic Faster Error

06 Periodic Slower Error

07

Update-ended Interrupt

Error

The acquired refreshing frequency is out of the estimated range.

Reset the estimated range.

The pattern read out from the L1

Cache is different from the one that has been written in the same machines. address.

Test this unit on multiple

Interference between different data channels.

As above.

Failure during the transfer speed test.

As above.

DMA channel cannot transfer data normally.

Repeat multiple times. Whether there is always the same error, replace the board.

The difference between the actual precision of the interval timer and its theory value is out of the permitted range. The timer

As above. counts imprecisely.

The frequency is beyond the standard.

The frequency is below the standard.

R/W errors with the RTC refreshing interrupt controller.

As above.

As above.

As above.

dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual 61

3 Diagnostic Programs 3.11Error Codes and Description

08 RTC Alarm Error

PCI Config Verification

Error

The PC speaker's sound source --

-counter/timer 8253 cannot produce corresponding timing signal.

As above.

13 PCI Bus Error

14 PCI Bus Scan Error

No PCI.

PCI test fails.

15 PCI Device Access Error PCI access fails.

16

17

Wrong PCI configuration.

PCI to ISA Bridge Error PCI-ISA bridge errors.

Check the board.

As above.

As above.

Check PCI configuration on main board or PCI Device configuration.

Repeat multiple times. If there is always the same error, replace the board.

18 ESCD Error ESCD errors. As above.

34xx

53 ACPI Table Test Error Errors with the ACPI table test. As above.

FAN

01 Fan Slow Speed Test Fail The fan slow speed test fails. Check the FAN connection.

04xx

02 Fan Stop Test Fail The fan stop test fails. As above.

03 Fan Fast Speed Test Fail The fan fast speed test fails. As above.

Video

01 Text Attribute Error

Physical problems with the video

Check whether there is any card. physical problem with the video card.

02 Text Page Selection Error As above. As above.

03 Text Color Error As above. As above.

04 Text Mode Error As above. As above.

05

06

07

VGA Mode Error

Character Test Error

1) Physical problems with the video card.

2) Physical problems with the monitor.

1) Check whether there is any physical problem with the video card.

2) Check whether there is any physical problem with the monitor.

Physical problems with the video

Check whether there is any card. physical problem with the video card.

DAC/Palette Address Test

As above.

Error

As above.

62 dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual

3.11Error Codes and Description 3 Diagnostic Programs

08 Color Purity Test Error

Physical problems with the video

Check whether there is any card or the monitor. physical problem with the video card or the monitor.

09

10

11

12

VESA Mode 15bits Direct

As above.

Color Test Error

VESA Mode 16bits Direct

As above.

Color Test Error

As above.

As above.

VESA Mode 24bits Direct

As above.

Color Test Error

Get the PCX graphics map Failure in getting PCX graphics

Error map.

As above.

Check for the PCX graphics map.

13 Bitblt Engine Test Error

Physical problems with the video Check and see whether the video card. card has any physical problem.

14

VESA Video Memory

Test Error

As above. As above.

15 VESA VRAM Test Error

16 AGP Test Error

Physical proble ms with the video

Check whether there is any card or the monitor. physical problem with the video card or the monitor.

AGP configuration register errors.

Check and see whether the AGP video card has any physical problem.

17 LCD Panel Test Error Lower LCD color resolution. Replace the LCD.

19 Register Test Error

Physical problems with the video Check and see whether the video card. card has any physical problem.

20 Adapter not support DDC

The video card doesn't support

DDC.

21 Monitor not support DDC

The monitor doesn't support

DDC.

21

8bits Text and Attribute

Test Error

1) Physical problems with the video card.

2) Physical problems with the monitor.

1) Check and see whether the video card has any physical problem.

2) Check and see whether the monitor has any physical problem.

26

27

8bits Video Mode Test

Error

15bits Video Mode Test

Error

As above.

As above.

As above.

As above.

28

29

16bits Video Mode Test

Error

As above.

24bits Video Mode Test

Error

As above.

As above.

As above.

dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual 63

3 Diagnostic Programs 3.11Error Codes and Description

31xx

11xx

08xx

09xx

30

32bits Video Mode Test

Error

Audio

As above. As above.

01 Audio Play Fail

02 Record Fail

Cannot play music.

Cannot record.

Check the Audio connection, replace the external fixture, and repeat the test.

As above.

LPT

01

02

03

04

05

Data Register Error

Control Register Error

Does not Support ECP

Mode(Ver3.20)

FIFO Test Error

IRQ Active Error

The data register can not perform Check the external fixture and normally. BIOS setup, and repeat the test.

The control register can not perform normally.

As above.

LPT does not support ECP mode.

Check the BIOS setup, and repeat the test.

LPT cannot perform normally under FIF0 TEST mode (ECP internal mode).

1.LPT IRQ cannot be activated.

2. The external fixture does not match with the chosen version.

As above.

Check the external fixture and

BIOS setup, and repeat the test.

06 No Fixture On The Port No external fixtures on LPT port. As above.

09

CTR/STR Connection

Error

1. There is OC (Open Circuit) or

SC (Short Circuit) on the LPT port CTR/STR.2. The external fixture does not match with the chosen version.

Check the external fixture and the port pins, and repeat the test.

10

DTR/STR Connection

Error

As above.

11 Toshiba Fixture Error As above.

As above.

As above.

LAN Card

01

02

03

PCI bus Error during device ID test

PCI Ethernet card not present during device ID test

Intel PCI Ethernet card not present during MAC test

Don’t Scan PCI device

Don’t find Net card

Keyboard

Don’t support PCI BIOS

Please insert Net cad

Don’t found Net Card, This Card

Please update net card or use can’t be Read MAC by this method other method

01

Keyboard Map & Stroke

Test Fail

Keyboard Map & Stroke Test fails.

Check the KBD connection and repeat the test.

03 Clock Line Test Fail Clock Line Test fails. As above.

64 dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual

3.11Error Codes and Description 3 Diagnostic Programs

05xx

14xx

04 Data Line Test Fail

Mouse

01 Touch Pad Test Fail

01

IrDA Test

2400BPS Test Error

02 4800BPS Test Error

03 9600BPS Test Error

04 19200BPS Test Error

05 38400BPS Test Error

Data Line Test fails. As above.

Touch Pad Test Fail

Check the mouse connection and repeat the test.

Failure with the infrared port or the configuration program is not executed.

Rerun the configuration program or check the infrared port.

As above. As above.

As above.

As above.

As above.

As above.

As above.

As above.

06 57600BPS Test Error As above.

07 115200BPS Test Error As above.

08 0.576MBPS Test Error As above.

As above.

As above.

As above.

09 1.152MBPS Test Error As above. As above.

30xx

10 4.000MBPS Test Error As above.

11

08

Connect time out

MemoryCard

Check PCI Device Fail

As above.

Failure with the infrared port or the configuration program is not executed.

Rerun the configuration program or check the infrared port. Check the master.

No Memory Card is inserted or the Memory Card is damaged.

Replace the Memory Card and repeat the test.

09

Start Flash Media Tests

Fail

As above. As above.

10

Verifying Firmware loaded Fail

As above.

11

MMC or SD Media Card

Present Fail

As above.

As above.

As above.

dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual 65

3 Diagnostic Programs 3.11Error Codes and Description

21xx

28xx

20xx

1394

01

IDE-HDD

01 Get Parameter Fail !

Can not find IEEE1394 controller

Wrong test parameters are input by user.

Don’t support 1394.

Reinput the correct parameters.

HD is damaged. Send the HD for repair. 02 Write Pattern Error

03 Data Compare Error HD is damaged. As above.

04 Read Verify Error HD is damaged. As above.

05 Seek Error

06

07

09

10

Disk Controller Self Test

Failed

Disk Controller Test unexpected interrupt

Failed

Disk Controller action

Test Failed

Disk dos not support

SMART

HD is damaged.

Disk dos not support SMART

As above.

The HD controller is damaged. As above.

The HD controller is damaged. As above.

The HD controller is damaged. As above.

Change HD which supported

SMART and test again

11

Disk read attribute threshold error

Send the HD for repair.

12

13

Disk read attribute threshold error

Disk read attribute value error

Disk SMART attribute value error

Disk read attribute value error

Disk SMART attribute value error

As above.

As above.

ODD

01

02

03

04

07

No Disk in CDROM

The Disk in CDROM is not Data Disk

No disk is found in the CD-

ROM.

The disk in the CD-ROM is not

Data Disk.

IDE-CD Controller Error Functional errors with the CD-

ROM.

CD Read Error Either the disk or the CD-ROM is damaged.

CD Seek Error

Eject Error

Either the disk or the CD-ROM is damaged.

Wrong CD-ROM drive.

Insert a disk into the CD-ROM.

Insert a DATA CD.

Send the CD-ROM for repair.

Replace the disk or send the CD-

ROM for repair.

Replace the disk or send the CD-

ROM for repair.

Exit from the wrong drive.

09

66 dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual

3.12 Quick Test Item List

Device

CPU

Memory

Board

FAN

Video

HDD

LAN Card

3.12 Quick Test Item List

Test Items

Basic Functionality

NPU Basic Functions

CPU Information

BIOS ROM

Cache Memory

Bit Stuck High Test

Bit Stuck Low Test

Address Test

Interval Timer

Clock / Calendar

ACPI Test

FAN Speed

1024X768 Video Modes Test:

VESA 1024x768x64K Mode

VESA 1024x768x32bit Mode

VESA Video Memory

Color Purity Test

Direct Color Test

LCD Panel

Sequential/Random R/W

SMART Check

Device ID Detection

Vendor ID Detection

Mac Address Detection

3 Diagnostic Programs

Comment

10% or 3 minutes

10% or 3 minutes

10% or 3 minutes

25% or 3 minutes

dynabook AX/Satellite AW2/Equium A60/Satellite A60/ Satellite Pro A60 A65 Maintenance Manual 67

Chapter 4

4

Replacement Procedures

1

4 Replacement Procedures

4-ii Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual

4 Replacement Procedures

Chapter 4 Contents

4.1 General........................................................................................................................ 4-1

Safety Precautions.................................................................................................. 4-2

Before You Begin .................................................................................................. 4-4

Disassembly Procedures......................................................................................... 4-5

Assembly Procedures............................................................................................. 4-5

Tools and Equipment.............................................................................................. 4-6

Screw Tightening Torque........................................................................................ 4-6

Colors of Screw Shanks......................................................................................... 4-7

Symbols of Screws on the Computer Body............................................................. 4-7

Symbol examples................................................................................................... 4-7

Removing the Battery Pack .................................................................................... 4-8

Installing the Battery Pack ...................................................................................... 4-9

Removing the Optional PC Card .......................................................................... 4-10

Installing the Optional PC Card ............................................................................ 4-11

Removing the Optional Memory........................................................................... 4-12

Installing the Optional Memory............................................................................. 4-14

Removing the MDC Card .................................................................................... 4-15

Installing the MDC Card ...................................................................................... 4-17

4.2 Wireless LAN Card................................................................................................... 4-18

Removing the Wireless LAN Card ....................................................................... 4-18

Installing the Wireless LAN Card ......................................................................... 4-19

4.3 HDD ......................................................................................................................... 4-20

Removing the HDD.............................................................................................. 4-20

Installing the HDD................................................................................................ 4-22

4.4 Switch Cover and Hotkey Board................................................................................ 4-23

Removing the Switch Cover and Hotkey Board .................................................... 4-23

Installing the Switch Cover and Hotkey Board ...................................................... 4-24

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual 4-iii

4 Replacement Procedures

4.5 Keyboard .................................................................................................................. 4-25

Removing the Keyboard....................................................................................... 4-25

Installing the Keyboard......................................................................................... 4-26

4.6 ODD Bay Module ..................................................................................................... 4-27

Removing the ODD Bay Module.......................................................................... 4-27

Installing the ODD Bay Module............................................................................ 4-28

Disassembling the ODD Bay Module.................................................................... 4-29

Assembling the ODD Bay Module........................................................................ 4-29

4.7 Display Assembly....................................................................................................... 4-30

Removing the Display Assembly........................................................................... 4-30

Installing the Display Assembly............................................................................. 4-31

4.8 Top Cover................................................................................................................. 4-32

Removing the Top Cover ..................................................................................... 4-32

Installing the Top Cover ....................................................................................... 4-34

4.9 Speakers ................................................................................................................... 4-35

Removing the Speakers........................................................................................ 4-35

Installing the Speakers.......................................................................................... 4-36

4.10 Cooling Module ......................................................................................................... 4-37

Removing the Cooling Module.............................................................................. 4-37

Installing the Cooling Module................................................................................ 4-38

4.11 CPU.......................................................................................................................... 4-40

Removing the CPU .............................................................................................. 4-40

Installing the CPU................................................................................................ 4-41

4.12 System Board ............................................................................................................ 4-43

Removing the System Board................................................................................. 4-43

Installing the System Board................................................................................... 4-44

4.13 North Bridge Cooling Module and MDC cable........................................................... 4-45

Removing the North Bridge Cooling Module and MDC cable ............................... 4-45

Installing the North Bridge Cooling Module and MDC cable ................................. 4-46

4.14 Display Mask............................................................................................................. 4-47

4-iv Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual

4 Replacement Procedures

Removing the Display Mask................................................................................. 4-47

Installing the Display Mask................................................................................... 4-48

4.15 FL Inverter Board...................................................................................................... 4-49

Removing the FL Inverter Board .......................................................................... 4-49

Installing the FL Inverter Board ............................................................................ 4-50

4.16 LCD Modules............................................................................................................ 4-51

Removing the 15.0-inch LCD module................................................................... 4-51

Installing the 15.0-inch LCD Module .................................................................... 4-53

Removing the 14.0-inch LCD module................................................................... 4-54

Installing the 14.0-inch LCD Module .................................................................... 4-56

4.17 LED Board................................................................................................................ 4-57

Removing the LED Board .................................................................................... 4-57

Installing the LED Board……………………………………………………....4-58

4.18 Touch Pad Board....................................................................................................... 4-59

Removing the Touch Pad Board ........................................................................... 4-59

Installing the Touch Pad Board ............................................................................. 4-59

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual 4-v

4 Replacement Procedures

Figures

Figure 4-1 Removing the battery pack ..................................................................................... 4-8

Figure 4-2 Removing the battery pack ..................................................................................... 4-9

Figure 4-3 Removing the PC card ......................................................................................... 4-10

Figure 4-4 Removing the memory cover ................................................................................ 4-12

Figure 4-5 Removing the optional memory............................................................................. 4-13

Figure 4-6 Removing the MDC cover.................................................................................... 4-15

Figure 4-7 Removing the MDC card ..................................................................................... 4-16

Figure 4-8 Removing the wireless LAN card cover................................................................. 4-18

Figure 4-9 Removing the wireless LAN card ......................................................................... 4-19

Figure 4-10 Removing the HDD pack ................................................................................... 4-20

Figure 4-11 Removing the HDD pack cover.......................................................................... 4-21

Figure 4-12 Removing the HDD chassis ................................................................................ 4-21

Figure 4-13 Removing the switch cover ................................................................................ 4-23

Figure 4-14 Removing the hotkey board................................................................................ 4-24

Figure 4-15 Removing the keyboard...................................................................................... 4-25

Figure 4-16 Removing the ODD bay module ......................................................................... 4-27

Figure 4-17 Removing the ODD bay module ......................................................................... 4-28

Figure 4-18 Removing the breaket from the ODD drive ......................................................... 4-29

Figure 4-19 Removing the screws from the bottom of the computer........................................ 4-30

Figure 4-20 Removing the display assembly........................................................................... 4-31

Figure 4-21 Removing the screws from the bottom of the computer........................................ 4-32

Figure 4-22 Removing the top cover...................................................................................... 4-33

Figure 4-23 Removing the speakers....................................................................................... 4-35

Figure 4-24 Removing the cooling module ............................................................................. 4-37

Figure 4-25 Applying silicon greases ..................................................................................... 4-38

Figure 4-26 Removing the CPU ............................................................................................ 4-40

Figure 4-27 Installing the CPU .............................................................................................. 4-41

Figure 4-28 Fixing the CPU .................................................................................................. 4-42

4-vi Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual

4 Replacement Procedures

Figure 4-29 Removing the system board................................................................................ 4-43

Figure 4-30 Removing the north bridge thermal module.......................................................... 4-45

Figure 4-31 Removing the MDC cable .................................................................................. 4-46

Figure 4-32 Removing the display mask................................................................................ 4-47

Figure 4-33 Removing the FL inverter board ......................................................................... 4-49

Figure 4-34 Disconnecting the cables...................................................................................... 4-50

Figure 4-35 Removing the 15.0-inch LCD module and screws............................................... 4-51

Figure 4-36 Removing the 15.0-inch LCD module................................................................. 4-52

Figure 4-37 Removing the 15.0-inch LCD module................................................................. 4-52

Figure 4-38 Removing the 14.0-inch LCD module and screws............................................... 4-54

Figure 4-39 Removing the 14.0-inch LCD module................................................................. 4-55

Figure 4-40 Removing the 14.0-inch LCD module................................................................. 4-55

Figure 4-41 Removing the LED board................................................................................... 4-57

Figure 4-42 Removing the touch pad board ........................................................................... 4-59

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual 4-vii

4.1 General 4 Replacement Procedures

4 1

4.1 General

This chapter explains how to disassemble the computer and replace Field Replaceable Units

(FRUs). Some replacement procedures may not require you to remove all the surrounding FRUs to replace only one FRU. The chart below shows the FRUs in the order in which they should be removed in a top-down manner, irrespective of their physical locations. The FRUs shown in the top area of the chart should normally be removed before removing the FRUs shown in the bottom area.

To replace the FRUs, first identify the suspect FRU for the system failure. Next, according to this chart, determine the FRUs that need to be removed before removing the suspect FRU. After you determined those FRUs, go to the appropriate sections according to the section numbers shown in the boxes. Then start removal and replacement

4. 2

Wireless LAN Card

4. 5

Keyboard

4. 3

HDD

4. 6

ODD Bay Module

4. 4

Switch cover and

Hotkey Board

4. 7

Display Assembly

4. 14

Display Mask

4.8

Top Cover

4. 15

FL Inverter Board

4. 9

Speakers

4. 10

Cooling Module

4. 12

System Board

4. 17

LED Board

4. 16

LCD Modules

4. 11

CPU

4.13

Cooling Module

4. 18

Touch Pad Board

How to use the chart (two examples):

4. 2

Wireless LAN Card

?

For removing the System Board

4. 5

Keyboard

First, remove the top cover with the

4.8

display assembly. Then, remove the

Top Cover

HDD, selectable bay module, Bluetooth card, keyboard, and wireless LAN card, all of which are shown above the

4. 9

Speakers top cover with the display assembly.

4. 3

HDD

4. 6

ODD Bay Module

4. 10

Cooling Module

4. 11

CPU

4. 12

System Board

4.13

North Bridge

THermal Module

4. 4

Switch cover and

Hotkey Board

4. 7

Display Assembly

4. 17

LED Board

4. 18

Touch Pad Board

?

For removing the LCD Module

First, remove the display mask and FL inverter board, both of which are shown above the LCD module.

4. 14

Display Mask

4. 15

FL Inverter Board

4. 16

LCD Modules

System Board

LCD Module

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual 4-1

4 Replacement Procedures 4.1 General

Safety Precautions

Before you begin disassembling, read the following safety precautions carefully. Be sure to follow them while you are working.

DANGER:

1. Always use the genuine batteries or replacement batteries authorized by Toshiba.

Batteries other than those differ in specifications and are incompatible with the computer. They may burst or explode. Never heat or disassemble the battery packs to avoid leakage of alkaline solutions. Never throw the battery packs into a fire. If this is

violated, they will explode.

2. The components such as the power supply and FL inverter carry high voltages. When you partially disassemble the computer and turn on the components, use extreme care not to touch the connectors and components to avoid the risk of electrical shock. Do not

disassemble individual components during first-level maintenance.

WARNING:

1. To avoid the risk of electrical shock, turn the computer off and remove the AC adapter

from the electrical outlet.

2. Because the battery in the computer is left charged, the risk of electrical shock remains even after the AC adapter is removed from the electrical outlet. To avoid the risk of electrical shock, be sure to put off any metal jewelry or accessories such as necklaces,

bracelets, and rings before starting work. Never work with your hands wet or damped.

3.

To avoid personal injury, use care to the sharp edges or corners of the components.

4-2

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual

4.1 General 4 Replacement Procedures

CAUTION:

1. Before replacing a component, make sure that the replacement component meets the required specifications. To avoid computer failures, never use components that do not

meet the specifications.

2. To avoid internal damage such as short circuits and fire, never drop metal objects such as screws, pins, paper clips, etc. into the components. When a screw is removed, be sure to replace a screw that is the same size as the original screw. Make sure that all the screws are fastened securely. Loose screws can cause short circuits, overheating, smoke,

or fire.

3. Before raising an FRU or other component, make sure that all the component cables have been disconnected to avoid the risk of electrical shock caused by accidental

contact with the energized components.

4. For AC input, be sure to use the AC adapter and AC power cable that come with your

computer or Toshiba-recommended equivalents.

5. To avoid the risk of electrical shock, make sure that all the replacement components meet the specifications of the computer and that all the cables and connectors are

fastened securely.

6. Inside the PC are components that become hot during operation (such as the CPU and cooling module). To avoid burns, let the hot components cool down before starting inspection or repair task.

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual 4-3

4 Replacement Procedures 4.1 General

Before You Begin

Before you begin disassembling the computer, keep in mind the precautions and advice in this section. Always begin disassembling from removing the AC adapter and battery pack. Remove the optional parts and accessories as well. The procedures for removing the batteries will be explained later.

Disassemble the computer only when an abnormality has occurred.

Use only the recommended tools.

To run and store the computer, be sure to prepare a working environment that is free from:

? Dust and contaminants

? Static electricity

? Extremely high or low temperatures and extremely high humidity

Run the diagnostic tests explained in Chapter 2 of this manual to identify the FRU that has probably caused the system failure.

Perform only the required machine operations. Use only the disassembly and reinstallation procedures described in this manual.

Place the removed components in a safe place away from the computer so that they may not be damaged or get in the way of you doing your work.

Normally, a number of screws need to be removed or replaced during disassembling. Place the removed screws in a safe place so that you can easily find the right screws for the right components.

When assembling the computer, use the specified screws to fasten the parts to the specified locations. See the appropriate explanations and figures for screw sizes.

To avoid personal injury, use care to handle components that have sharp edges or corners.

After you have replaced an FRU, check that the FRU works correctly to ensure normal computer operation.

4-4

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual

4.1 General 4 Replacement Procedures

Disassembly Procedures

The cable connectors come in these two basic types:

? Pressure plate connectors

? Normal pin connectors

To remove a pressure plate connector, pull up the tabs on either side of the connector's plastic pressure plate and gently pull the cable out of the connector. To reconnect the cable to the pressure plate's connector, raise the pressure plate up to a satisfactory height and slide the cable into the connector. Fix the cable to the correct position by pressing down the sides of the pressure plate so that the plate can be flush with the sides of the connector. Grasp and pull the cable gently to check that the cable is connected firmly. If the cable came off the connector, reinsert the cable by raising the pressure plate up to a satisfactory height.

Normal pin connectors are used for all the other types of cables. These connectors can be installed or removed by simply inserting them or pulling them out.

Assembly Procedures

You have to reassemble the computer after you disassembled the computer and fixed the component that caused the problem.

When reassembling the computer, keep the following general guidelines in mind:

? Take your time to carry out the suggested instructions completely. Hurried reassembling can often cause problems.

? Check that all the cable and connectors are fastened securely.

? Before fixing the FRUs or other parts, check that the cables are not caught by the screws or

FRUs.

? Check that all the latches are closed securely.

? Check that all the required screws are used to fix the FRUs. Using wrong screws can damage the threads or heads of the screws or does not ensure firm FRU fixing.

After installing an FRU, make sure that the FRU and computer can work normally.

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual 4-5

4 Replacement Procedures 4.1 General

Tools and Equipment

For the safety of you and other people in the working environment, it is strongly recommended to use electrostatic discharge (ESD) equipment. The proper use of this equipment will ensure successful repair work and reduce the costs for fixing damaged components. The equipment and tools required for disassembling and reassembling are:

? One 2 mm Phillips screwdriver

? One 4 mm flat-blade screwdriver

? Torx screwdriver

? Tweezers (for pulling out screws)

? ESD mats (for the floor and work desks)

? An ESD wrist strap or heel grounder

? Anti-static carpets or flooring

? Air ionizers (for highly electrostatic sensitive areas)

? A plastic card (in credit card size)

Screw Tightening Torque

To fasten screws, follow the torque values listed below. Overtightening can damage components and screws. Undertightening can loosen the fastening or make screws come off, which may result in short circuits or other damage.

? M2 (2 mm)

? M2.5 (2.5 mm)

0.22 N?m (2.2 kgf?cm)

0.36 N?m (3.5 kgf?cm)

? M3 (3 mm)

0.51 N?m (5.0 kgf?cm)

? M2.5x4 PSP TITE screws

0.204 N?m (2.0 kgf?cm)

? M2.5x6 GIZA TITE screws 0.36 N?m (3.5 kgf?cm)

4-6

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual

4.1 General 4 Replacement Procedures

Colors of Screw Shanks

For easy identification of the correct screws, the screw shanks are colored according to their lengths, as follows:

? Screws of an even-numbered length

Brown

? Screws of an odd-numbered length

White

? Screws of a special length

Black

Screws of a special length are those of a length having decimal places, such as 2.5 mm and

2.6 mm.

Symbols of Screws on the Computer Body

For easy maintenance, the screw types are shown on the computer body as symbols. A symbol consists of a letter representing the screw type and a numeral representing the screw length.

? Screw type

? Bind screw

? Flat-head screw

? Super flat-head screw

? Tapping screw

? Other screws

Letter

B (stands for bind)

F (stands for flat-head)

S (stands for super flat-head)

T (stands for tapping)

U (stands for unique-pan head screws, studs, etc.)

Symbol examples

? 6 mm bind screw

? 12 mm bind screw

B6

B12

? 5 mm stud

U5

(The numeral represents the rounded length of the threaded portion irrespective of the entire stud length.)

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual 4-7

4 Replacement Procedures 4.1 General

Removing the Battery Pack

Remove the battery pack according to the following procedures and Figures 4-1, 4-2.

CAUTION: When handling the battery packs, use care not to short circuit the terminals.

Do not drop, hit, twist, or bend the battery packs. Do not scratch or break up their casing.

1. Turn the computer upside down so that its front can face you.

2. Slide out the battery lock 1 and 2.

3. Slide the battery release latch 3 and remove the battery pack from the computer.

Figure 4-1 Removing the battery pack

NOTE: Dispose of the used battery packs as required by local ordinances or regulations.

4-8

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual

4.1 General 4 Replacement Procedures

Battery pack

Figure 4-2 Removing the battery pack

Installing the Battery Pack

Install the battery pack according to the following procedures and Figures 4-1, 4-2.

CAUTION: The battery packs contain a lithium ion battery, which can explode by improper replacement, use, handling, or disposal. Always dispose of the battery packs as required by local ordinances or regulations. Use only replacement batteries recommended by Toshiba.

NOTE: Visually check the battery's terminals. If they are dirty, clean them with a dry cloth.

1. Gently insert a new or recharged battery pack into place. Check that the battery release latch slides in and stops with a click.

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual 4-9

4 Replacement Procedures 4.1 General

Removing the Optional PC Card

Remove the optional PC card according to the following procedures and Figure 4-3, after checking that computer is turned off in boot mode.

CAUTION: Install or remove the PC card correctly, according the manuals of the PC card and the operating system you are using.

1. Push the eject button for the PC card to be removed until it stops and release the button.

2. When the eject button popped out slightly, push it again.

3. When the PC card popped out, grasp it and pull it out.

PC card

Eject button

Figure 4-3 Removing the PC card

4-10

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual

4.1 General 4 Replacement Procedures

Installing the Optional PC Card

Install the optional PC card according to the following procedures and Figure 4-3, after checking that the computer is turned off in boot mode.

1. Insert the PC card gently until it stops and is seated securely.

2. After checking that the PC card is seated securely, push the PC card release lever slightly.

After the PC card is installed, check the hardware configuration in the Hardware Setup or TSETUP program to make sure that the PC card in compatible with the current hardware configuration.

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual 4-11

4 Replacement Procedures 4.1 General

Removing the Optional Memory

Remove the optional memory (module) according to the following procedures and Figures 4-4 and

4-5, after checking that the computer is turned off in boot mode.

CAUTION: Remove the optional memory after turning off the computer. If this is violated, the computer or memory can be damaged.

1. Turn the computer upside down.

2. Release one M2.5x4 black bind screw.

3. Remove the memory cover.

CAUTION: Do not touch the connectors on the memory modules or in the computer.

Contaminated connectors can cause memory access problems.

M2.5x4 black bind screw

Memonry cover

Figure 4-4 Removing the memory cover

4-12

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual

4.1 General 4 Replacement Procedures

4. Spread out the two memory lock stoppers so that the memory module can be raised.

5. Pull the memory module up and out at an angle, using care to the connectors.

Stoper

Slot

Menory

Memory

Figure 4-5 Removing the optional memory

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual 4-13

4 Replacement Procedures 4.1 General

Installing the Optional Memory

Install the optional memory (module) according to the following procedures and Figures 4-4 and 4-

5, after checking that the computer is turned off in boot mode.

CAUTION: Install the optional memory after turning off the computer. If this is violated, the computer or memory can be damaged.

1. Insert the memory module into the connector at an angle of 45 degrees.

2. Tilt the memory module so that it can be fixed with both memory lock stoppers.

3. Reinstall the memory cover.

4. Secure the cover with the M2.5x4 black bind screw.

After the computer is turned on, check the hardware configuration in the Hardware Setup or

TSETUP program to make sure that the installed memory module has been recognized by the system. If it has not been recognized yet, check the connections.

CAUTION: To prevent system malfunctions, always use Slot A first to insert the memory modules.

4-14

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual

4.1 General 4 Replacement Procedures

Removing the MDC Card

Remove the MDC Card (Modem Daughter Card) according to the following procedures and

Figures 4-6 and 4-7, after checking that the computer is turned off in boot mode.

CAUTION: Remove the MDC card after turning off the computer. If this is violated, the computer or MDC card can be damaged.

1. Turn the computer upside down.

2. Release the M2.5x4 black bind screws.

3. Remove the MDC cover.

CAUTION: Do not touch the connectors on the MDC card or in the computer.

Contaminated connectors can cause MDC card failures.

M2.5x4 black bind screw

MDC cover

Figure 4-6 Removing the MDC cover

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual 4-15

4 Replacement Procedures

4. Remove the two M2x3 white bind screws for securing the MDC card.

5. Raise the MDC card and disconnect it from CN502 on the system board.

6. Disconnect the MDC cable from the connector JP1 on the MDC card.

M2X3 white bind screw

J P 2

MDC card

J P 1

CN5002

MDC cable

4.1 General

Figure 4-7 Removing the MDC card

4-16

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual

4.1 General 4 Replacement Procedures

Installing the MDC Card

Install the MDC card according to the following procedures and Figures 4-6 and 4-7, after checking that the computer is turned off in boot mode.

CAUTION: Install the MDC card after turning off the computer. If this is violated, the computer or MDC card can be damaged.

CAUTION: Do not touch the connectors on the MDC card or in the computer.

Contaminated connectors can cause MDC card failures.

1. Connect the MDC cable to the connector JP1 on the MDC card.

2. Connect the MDC card to CN502 on the system board.

3. Securing the MDC card with the two M2x3 white bind screws.

4. Install the MDC cover.

5. Securing the MDC cover by one M2.5x4 black bind screw.

After the computer is turned on, check the hardware configuration in the Hardware Setup or

TSETUP program to make sure that the installed MDC card has been recognized by the system. If it has not been recognized yet, check the connections.

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual 4-17

4 Replacement Procedures

4.2 Wireless LAN Card

4.2 Wireless LAN Card

Removing the Wireless LAN Card

Remove the wireless LAN card according to the following procedures and Figures 4-8 and 4-9.

CAUTION: Do not touch the connectors on the wireless LAN card and in the computer with bare hands. Wireless LAN cards can fail if they are contaminated with sweat, natural oils, etc. from your hands.

1. Turn the computer upside down.

2. Release the M2.5x4 black LHSTIX screws.

3. Remove the Wireless LAN cover.

4. Disconnect the two antenna cables with the tweezers.

5. Spread out both the left and right stoppers for fixing the wireless LAN card until the card can be raised.

6. Pull the wireless LAN card up and out at an angle.

M2.5x4 screw

Wireless cover

4-18

Figure 4-8 Removing the wireless LAN card cover

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual

4.2 Wireless LAN Card

Black wire

Antenna cable

4 Replacement Procedures

Stopper

White wire

Wireless LAN card

Figure 4-9 Removing the wireless LAN card

Installing the Wireless LAN Card

Install the wireless LAN card according to the following procedures and Figures 4-22.

1. Insert the wireless LAN card into the connector at angle of 45 degrees.

2. Tilt the wireless LAN card and fix it with the left and right stoppers.

3. Connect the two antenna cables with the tweezers.

4. Install the wireless LAN cover.

5. Securing the wireless LAN cover by one M2.5x4 black LHSTIX screw.

CAUTION: Do not touch the connectors on the wireless LAN card and in the computer with bare hands. Wireless LAN cards can fail if they are contaminated with sweat, natural oils, etc. from your hands.

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual 4-19

4 Replacement Procedures 4.3 HDD

4.3 HDD

Removing the HDD

CAUTION: Do not press the top or bottom of the drive.

Applying such pressure can corrupt the data in the drive or damage the drive.

Remove the HDD (hard disk drive) according to the following procedures and Figures 4-10, 4-11 and 4-12.

1. Remove one M2.5x6 black flat-head screw for fixing the HDD cover.

2. Remove the HDD cover.

3. Remove the HDD pack sliding it in the direction of the arrows.

M2.5x6 black bind screw

HDD cover

Figure 4-10 Removing the HDD pack cover

4-20

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual

4.3 HDD 4 Replacement Procedures

HDD pack

Figure 4-11 Removing the HDD pack

4. Remove the HDD pack by pulling the HDD tap attached to the HDD pack.

NOTE: Do not disassemble the HDD pack when it is working normally. Disassemble or replace the HDD pack only if it failed.

5. Place the HDD pack on a flat surface (such as a desk), and remove the two M3x4 black flat-head screws.

6. Remove the HDD bracket.

HDD

M3x4 black flat-head screw

HDD bracket

Figure 4-12 Removing the HDD chassis

CAUTION: Do not apply pressure to the top or bottom of the drive.

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual 4-21

4 Replacement Procedures 4.3 HDD

Installing the HDD

Install the HDD according to the following procedures and Figures 4-10, 4-11 and 4-12.

CAUTION: To avoid damage, always hold the HDD only by its sides.

1. Secure the HDD and its bracket with the two M3x4 black flat-head screws.

CAUTION: When installing the HDD pack into the computer, do not press the center of the HDD pack to prevent the HDD bracket from being distorted. Always hold the HDD pack by its sides.

2. Install the HDD pack into the correct position in the computer. Connect the HDD pack to the computer, holding the HDD pack by its sides.

3. Insert the HDD pack.

4. Secure the HDD cover with one M2.5x6 black flat-head screw.

4-22

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual

4.4 Switch Cover and Hotkey board 4 Replacement Procedures

4.4 Switch Cover and Hotkey Board

Removing the Switcher

Remove the switch cover and hotkey board according to the following procedures and Figures 4-

13, 4-14.

1. Open the display panel.

2. Release the following 11 latches on the switch cover, in that order:

- Six bottom latches

- One latch on the left and right sides

- Three front latches

3. Remove the switch cover.

4. Disconnect the SUMI-card (flat cable) from CN2001 on hotkey board.

Latch

5.

6.

Figure 4-13 Removing the switch cover screw

Remove the two M2.5 x4 black flat-head screws for securing the hotkey board.

Remove the hotkey board.

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual 4-23

4 Replacement Procedures 4.4 Switch Cover and Hotkey board

SUMI-card

CN2001

M2.5x4 black flat-head screw

Hotkey board

Figure 4-14 Removing the hotkey board

Installing the Switch Cover and Hotkey Board

Install the switch cover and hotkey board according to the following procedures and Figures 4-13,

4-14.

1. Connect the SUMI-card to CN2000 on the hotkey board.

2. Place the hotkey board in the correct position.

3. Secure the hotkey board with the two M2.5x4 black flat-head screws.

4. Place the switch cover in the correct position and fasten the following 11 latches, in that order:

- Six bottom latches

- One latch on the left and right sides

- Three front latch

4-24

Equium A60/ Satellite A60/ Pro A60/ A65

Maintenance Manual

4.5 Keyboard 4 Replacement Procedures

4 1

4.5 Keyboard

Removing the Keyboard

Remove the keyboard according to the following procedures and Figures 4-15.

1. Remove two M2.5x2.6 black bind screws.

Figure 4-15 Removing the keyboard

2. Move the keyboard in the direction of the arrow until the keyboard connector appears.

3. Turn the keyboard upside down.

4. Disconnect the keyboard cable from CN16 on the system board and remove the keyboard.

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual 4-25

4 Replacement Procedures 4.5 Keyboard

Installing the Keyboard

Install the keyboard according to the following procedures and Figures 4-15.

1. Connect the keyboard cable to CN16 on the system board.

2. Align the latches on the rear of the keyboard with the latch holes on the top cover.

3. Secure the keyboard with the two M2.5x2.6 black bind screws.

4-26 Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual

4.6 ODD Bay Module 4 Replacement Procedures

4.6 ODD Bay Modules

Removing the ODD Bay Module

NOTE: The installation and removal procedures are the same for all the modules that can be installed in the ODD bays. See the appropriate sections for the disassembly procedures of the specific modules.

Remove the ODD bay module according to the following procedures and Figure 4-16, 4-17.

1. Turn the computer upside down.

2. Remove the M2x8 black bind screw.

3. Turn the computer over and open the display.

4. Push out the ODD bay module in the direction of the arrow.

CAUTION: Handle the ODD bay module carefully, because it becomes hot during operation.

M2x8 black bind screw

Figure 4-16 Removing the ODD bay module

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual 4-27

4 Replacement Procedures

Push here

4.6 ODD Bay Module

ODD bay module

Figure 4-16 Removing the ODD bay module

Installing the ODD Bay Module

Install the ODD bay module according to the following procedures and Figure 4-16, 4-17.

1. Place the ODD bay module in the correct position and slide it in.

2. Push it until it clicks into place.

3. Close the display and turn the computer over.

4. Fix the ODD bay module with one M2x8 black bind screw.

4-28 Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual

4.6 ODD Bay Module 4 Replacement Procedures

Disassembling the ODD Drive

NOTE: Do not disassemble the ODD drive when it is working normally. Disassemble or replace the ODD drive only if it failed.

Disassemble the ODD drive according to the following procedures and Figures 4-18.

1. Remove the two M2x3 white flat-head screws.

2. Remove the bracket.

ODD bay module

Breaket

M2x3 white flat-head screw

Figure 4-18 Removing the bracket from the ODD drive

Assembling the ODD Drive

Assemble the ODD drive according to the following procedures and Figures 4-18.

1. Secure the bracket with the two M2x3 white flat-head screws.

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual 4-29

4 Replacement Procedures 4.7 Display Assembly

4.7 Display Assembly

Removing the Display Assembly

CAUTION: Use care to avoid that the antenna cable for antenna is caught between the display assembly and computer.

Remove the display assembly with the top cover according to the following procedures and Figures

4-19, 4-20.

1. Turn the computer upside down, and remove two M2.5x20 black bind screws.

2. Remove the wireless LAN cable core.

4-30

Figure 4-19 Removing the screws from the bottom of the computer

3. Restore the normal computer placement and open the display panel.

4. Remove four M2.5x5 black flat-head screws and M2x3 white flat-head screw .

5. Disconnect the LCD/FL cable from CN13 on the system board.

6. Remove the wireless antenna cables from the hole.

7. Remove the display module.

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual

4.7 Display Assembly 4 Replacement Procedures

Figure 4-20 Removing the display assembly

Installing the Display Assembly

Install the display assembly according to the following procedures and Figures 4-19, 4-20.

1. Place the display panel in the correct position and push the wireless antenna cable into the hole.

2. Connect the LCD/FL cable to CN13 on the system board and fix it with one M2x3 white flat-head screw.

3. Securing display assembly with four M2.5x5 black flat-head screws.

4. Close the display panel and turn the computer upside down and fix it with two M2.5x20 black bind screws.

5. Push the wireless LAN cable through the core and place the core in the correct position.

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual 4-31

4 Replacement Procedures 4.8 Top Cover

4.8 Top Cover

Removing the Top Cover

Remove the top cover according to the following procedures and Figures 4-21 and 4-22.

1. Turn the computer upside down, and remove the following 25 screws:

- Two M2.5x14 black bind screws

- Twelve M2.5x8 black bind screws

- Eleven M2.5x3 black flat-head screws

4-32

Figure 4-21 Removing the screws from the bottom of the computer

2. Restore the normal computer placement.

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual

4.8 Top Cover

LID switch cable

LED SUMI-card

4 Replacement Procedures

Top cover

CN23

CN17

Figure 4-22 Removing the top cover

3. Disconnect the LED board flat cable from CN17.

4. Lift up the top cover.

5. Disconnect the lid switch cable from CN23.

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual 4-33

4 Replacement Procedures 4.8 Top Cover

Installing the Top cover

Install the top cover with the display assembly according to the following procedures and Figures 4-

21, 4-22.

1. Connect the lid switch flat cables to CN23 on the system board.

2. Place the top cover, adjusting its position.

CAUTION: Use care to avoid that the lid switch cable for lid switch is caught between the top cover and base body.

3. Connect the LED board flat cable to CN17 on the system board.

4. Turn the computer upside down and fix it with the following 25 screws:

- Two M2.5x14 black bind screws

- Twelve M2.5x8 black bind screws

- Eleven M2.5x3 black flat-head screws

4-34 Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual

4.9 Speakers 4 Replacement Procedures

4.9 Speakers

Removing the Speakers

Remove the speakers according to the following procedures and Figure 4-23.

1. Remove the speaker cables fix tape.

2. Remove the speaker cables from the guides (grooves) on the bottom cover.

3. Disconnect the speaker cables from CN20 on the system board.

4. Remove the left and right speakers.

Tape

Figure 4-23 Removing the speakers

CN20

Speaker

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual 4-35

4 Replacement Procedures 4.9 Speakers

Installing the Speakers

Install the speakers according to the following procedures and Figure 4-23.

1. Connect the speaker cables to CN20 on the system board.

2. Place the left and right speakers in their correct position and push the speaker cables into the guides on the top cover.

3. Stick the speaker cables by the tape.

4-36 Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual

4.10 Cooling Module 4 Replacement Procedures

4.10 Cooling Module

CAUTION: When removing the cooling module, keep the following in mind:

1. The cooling module can become very hot during operation. Be sure to let it cool down

before starting the repair work.

2.

Do not touch or give shock to the fan in the cooling module.

NOTE: The screws for Steps 2 and 3 cannot be removed, only loosened.

Removing the Cooling Module

Remove the cooling module according to the following procedures and Figure 4-24.

1. Disconnect the cable of the cooling module from CN14 on the system board.

2. Release the one screw next to the fan.

3. Release the four screws on the cooling module using the numbered order shown to the screw.

4. Remove the cooling module.

Cooling module fix screw

Cooling module

CN14

C P U

Figure 4-24 Removing the cooling module

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual 4-37

4 Replacement Procedures

4.10 Cooling Module

Installing the Cooling Module

Install the cooling module according to the following procedures and Figures 4-24, 4-25.

CAUTION: When installing the cooling module, keep the following in mind:

1.

Be sure to confirm the correct position for the module.

2. Route the cooling module cable between the module and MDC card.

3. Please according to the number sequence sealed on heat sink module and secures the relevant screws on the main board.

NOTE: Apply silicon greases with a special syringe to cover the surface of the CPU chip completely.

4-38

Figure 4-25 Applying silicon greases

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual

4.10 Cooling Module 4 Replacement Procedures

1. If silicon greases are already applied to the CPU and fan module, wipe them off with a cloth.

By using a special syringe, apply silicon greases to the CPU chip center so that the entire

CPU chip can be covered with the greases.

2. Place the cooling module in the correct position.

3. Secure the four screws on the cooling module using the numbered order shown on the screws.

4. Secure one screw next to the fan.

5. Connect the cooling module cable to CN14 on the system board.

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual 4-39

4 Replacement Procedures

4.11 CPU

4.11 CPU

CAUTION: When removing the CPU, keep the following in mind:

The CPU can become very hot during operation. Be sure to let it cool down before starting repair work.

Removing the CPU

Remove the CPU according to the following procedures and Figure 4-26.

CAUTION: Remove the CPU by aligning the triangle with the shaded area.

1. Unlock the CPU by rotating the bar on the CPU socket 90 degrees to the up with hand (in the order shown in the figure below).

2. Remove the CPU.

NOTE: After the CPU is removed, should lower the bar before proceeding to prevent damage.

4-40

Figure 4-26 Removing the CPU

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual

4.11 CPU 4 Replacement Procedures

Installing the CPU

Install the CPU according to the following procedures and Figures 4-26, 4-27 and 4-28.

1. Check that the triangle on the cam is in the unlocking position.

2. Attach the CPU to the correct position in the CPU socket. Align the CPU with the CPU socket by using the triangle as a guide.

CPU socket

Figure 4-27 Installing the CPU

C P U

CAUTION: Place the CPU by aligning the triangle with the shaded area.

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual 4-41

4 Replacement Procedures

3. Secure the CPU by rotating the bar 90 degrees to the down with hand.

4.11 CPU

Figure 4-28 Securing the CPU

4-42 Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual

4.12 System Board 4 Replacement Procedures

4.12 System Board

Removing the System Board

NOTE: Be careful of the eject button for the PC card. It can be damage when removing the board. Make sure it is pushed in.

Remove the system board according to the following procedures and Figures 4-29.

1. Remove the M2.5x5 black flat-head screws for securing the HDD tray.

2. Remove the HDD tray.

3. Remove the hotkey board SUMI-card from CN8.

NOTE: The switch can be easily removed if you tweeze the prongs on the button together.

4. Remove the lever of the wireless kill switch.

5. Remove two M2.5x4 black flat-head screws for securing the system board.

6. Remove the system board.

Figure 4-29 Removing the system board

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual 4-43

4 Replacement Procedures

4.12 System Board

Installing the System Board

Install the touch pad according to the following procedures and figure 4-29.

1. Place the slider for the kill switch on the system board.

2. Seat the system board and secure it with two M2.5x4 black flat-head screws.

3. Connect the hotkey board SUMI-card to CN8 on the system board.

4. Seat the HDD tray and secure it with one M2.5x5 black flat-head screw.

5. Press the kill switch button through the opening in the side. Be sure the prongs are fully engaged.

4-44 Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual

4.13 North Bridge Thermal Module 4 Replacement Procedures

4.13 North Bridge thermal module and MDC cable

Removing North Bridge thermal module and MDC cable

Remove the North Bridge thermal module according to the following procedures and Figure 4-30,

4-31.

1. Disconnect the cable of the North Bridge thermal module from CN15 on the system board.

2. Turn the system board upside down.

3. Remove two M2x3 black bind screws and washers.

4. Remove North Bridge thermal module.

5. Remove the black sheet.

6. Remove one M2.5x2.5 white bind screws.

7. Removing the CD tray.

CD tray

North bridge thermal module

Black sheet

Washer

M2x3 black bind screw

M2.5x2.5 white band screw

System board

Figure 4 -30 Removing the North Bridge thermal module

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual 4-45

4 Replacement Procedures 4.13 North Bridge Thermal Module

8. Remove two pieces of sticky Mylar securing the MDC cable.

9. Disconnect the MDC cable from CN500 on the system board.

10. Remove the MDC cable.

MDC cable

CN500

Mylar

Figure 4-31 Removing the MDC cable

Installing the Removing North Bridge thermal module and MDC cable

Install the Removing North Bridge thermal module according to the following procedures and Figure

4-30, 4-31.

1. Place the MDC cable in the correct position...

2. Connect the MDC cable from CN500 on the system board.

3. Stick two pieces of sticky Mylar securing the MDC cable.

4. Connect the North Bridge thermal module cable to the CN15 on the system board.

5. Place the North Bridge thermal module in the correct position.

6. Secure the two washers and M2x3 black bind screws.

7. Place the CD tray in the correct position.

8. Secure the one M2.5x2.5 white bind screws.

4-46 Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual

4.13 North Bridge Thermal Module

9. Stick the black sheet in the correct position.

4 Replacement Procedures

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual 4-47

4 Replacement Procedures 4.14 Display Mask

4.14 Display Mask

Removing the Display Mask

Remove the display mask according to the following procedures and Figure 4-32.

1. Remove the following 8 seals on the display module in that order:

- Four black seals on the bottom

- Four black seals on the top

2. Remove the following 8 screw on the display module, in that order:

- Four M2.5x7 black flat-head screws on the top and bottom

- Four M2.5x7 black flat-head screws on each of the top and bottom of left and right sides

3. Release the following 18 latches on the display mask, in that order:

- Four bottom latches

- Five latches on each of the left and right sides

- Six top latches

4-48

Figure 4-32 Removing the display mask

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual

4.14 Display Mask 4 Replacement Procedures

Installing the Display Mask

Install the display mask according to the following procedures and Figure 4-32.

1. Place the display mask in the correct position and fasten the following 18 latches, in that order:

- Six top latches

- Five latches on each of the left and right sides

- Four bottom latches

2. Place the display module in the correct position and fasten the following 8 screws, in that order:

- Two M2.5x7 black flat-head screws on the top

- Four M2.5x7 black flat-head screws on each of the top and bottom of left and right sides

3. Place the display mask in the correct position and fasten the following 8 seals, in that order:

- Four black seals on the bottom

- Four black seals on the top

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual 4-49

4 Replacement Procedures 4.15 FL Inverter Board

4.15 FL Inverter Board

Removing the FL Inverter Board

Remove the FL inverter board according to the following procedures and Figures 4-33 and 4-34.

1. Remove the M2.5x4.5 black flat-head screw.

M2.5x4.5 black flat-head screw

FL inverter board

Figure 4-33 Removing the FL inverter board

2. Raise the FL inverter board and disconnect the LCD/FL cable from LCD/FL connecter.

3. Disconnect the HV cable from HV connecter and remove the FL inverter board.

4-50 Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual

4.15 FL Inverter Board 4 Replacement Procedures

FL inverter board

HV cable

LCD/FL cable

Figure 4-34 disconnecting the cables

Installing the FL Inverter Board

Install the FL inverter board according to the following procedures and Figures 4-33 and 4-34.

1. Connect the LCD/FL cable to LCD/FL connecter, and connect the HV cable to HV connecter.

2. Place the FL inverter board in the correct position.

3. Fasten the M2.5x4.5 black flat-head screw to secure the FL inverter board.

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual 4-51

4 Replacement Procedures

4.16 LCD Modules

4.16 LCD Module

NOTE: ICs are fragile. Use extreme care not to apply pressure to the ICs along the edges of the LCD module.

NOTE: Dispose of used LCD panels (fluorescent (FL) tubes) as required by local ordinances or regulations.

NOTE: LCD/FL cable must be carefully peeled away before disconnecting it from the module.

Removing the 15.0-inch LCD module

Remove the 15.0-inch LCD module according to the following procedures and Figures 4-35, 4-36 and 4-37.

1. Remove the two M2.5x4.5 black flat-head screws and two M2x5 white bind screws for fixing the LCD module.

2. Carefully tilt the LCD module toward you.

3. Remove the three M2x3 black bind screws on each of the left and right sides for fixing the

LCD bracket.

4-52 Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual

4.16 LCD Module 4 Replacement Procedures

M2x5 white bind screw

M2.5x4.5 black flat-head screw

Figure 4-35 Removing the 15.0-inch LCD module and screws

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual 4-53

4 Replacement Procedures 4.16 LCD Module

4. Remove the LCD brackets.

5. Turn the LCD upside down.

6. Remove the tape and LCD/FL cable connector. Then disconnect the LCD/FL cable.

Right LCD bracker

M2x3 black bind screw

LCD module

Left LCD bracker

M2x3 black bind screw

Figure 4-36 Removing the 15.0-inch LCD module

4-54

Figure 4-37 Removing the 15.0-inch LCD module

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual

4.16 LCD Module 4 Replacement Procedures

Installing the 15.0-inch LCD Module

NOTE: LCD/FL cable must be carefully peeled away before disconnecting it from the module.

Install the 15.0-inch LCD module according to the following procedures and Figures 4-35, 4-36 and 4-37.

1. Turn the LCD upside down.

2. Connect the LCD/FL cable to the LCD module then stick tape for securing the LCD connector.

3. Return the normal LCD placement.

4. Place the LCD bracket in the correct position and secure it with the three M2x3 black bind screws on each of the left and right sides.

5. Place the LCD module in the correct position and secure it with the two M2.5x4.5 black flat-head screws and two M2x5 white bind screws.

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual 4-55

4 Replacement Procedures 4.16 LCD Module

Removing the 14.1-inch LCD Module

NOTE: LCD/FL cable must be carefully peeled away before disconnecting it from the module.

Remove the 14.1-inch LCD module according to the following procedures and Figures 4-38, 4-39 and 4-40.

1. Remove the two M2.5x4.5 black flat-head screws and two M2x5 white bind screws for fixing the LCD module.

2. Carefully tilt the LCD module toward you.

3. Remove the three M2x3 black bind screws on each of the left and right sides for fixing the

LCD bracket.

M2x5 white bind screw

M2.5x4.5 black flat-head screw

Figure 4-38 Removing the 14.0-inch LCD module and screws

4-56 Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual

4.16 LCD Module 4 Replacement Procedures

4. Remove the tape and LCD/FL cable connector. Then disconnect the LCD/FL cable.

Right LCD bracker

M2x3 black bind screw

LCD module

Left LCD bracker

M2x3 black bind screw

Figure 4-39 Removing the 14.0-inch LCD module

Figure 4-40 Removing the 14.0-inch LCD module

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual 4-57

4 Replacement Procedures 4.16 LCD Module

Installing the 14.0-inch LCD Module

NOTE: LCD/FL cable must be carefully peeled away before disconnecting it from the module.

Install the 14.0-inch LCD module according to the following procedures and Figures 4-38, 4-39 and 4-40.

1. Turn the LCD upside down.

2. Connect the LCD/FL cable to the LCD module then stick tape for securing the LCD connector.

3. Return the normal LCD placement.

4. Place the LCD bracket in the correct position and secure it with the three M2x3 black bind screws on each of the left and right sides.

5. Place the LCD module in the correct position and secure it with the two M2.5x4.5 black flat-head screws and two M2x5 white bind screws.

4-58 Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual

4.17 LED board 4 Replacement Procedures

4.17 LED Board

Removing the LED Board

Remove the LED board according to the following procedures and Figure 4-41.

NOTE: Be carefully peel away the 3 tapes securing the board before you can remove it.

1. Remove the ESD tape for fix LED flat cable.

2. Remove the left and right sides fix touch pad ESD tape.

3. Remove the two M2.5x3 flat round head screws.

4. Disconnect the touch pad flat cables from J1 on the touch pad and remove the LED board.

5. Disconnect the touch pad flat cables from CN2000 and LED board flat cable from

CN2002 on the LED board.

ESD tape

J 1

ESD tape

LED SUMI-card

LED board

CN2002

CN2000

Touch pad SUMI-card

M2.5x3 flat-round-head screw

Figure 4-41 Removing the LED board

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual 4-59

4 Replacement Procedures 4.17 LED Board

Installing the LED Board

Install the LED board according to the following procedures and Figure 4-41.

1. Connect the touch pad flat cables to CN2000 and LED board flat cable to CN2002 on the

LED board.

2. Connect the touch pad flat cables to J1 on the touch pad.

3. Secure LED board to top cover with two M2.5x3 black flat round bind screws.

4. Stick touch pad flat cable by ESD tape on touch pad left side.

5. Stick LED board flat cable by ESD tape.

4-60 Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual

4.18 Touch Pad Board 4 Replacement Procedures

4.18 Touch Pad Board

Removing the Touch Pad Board

Remove the s Touch Pad Board according to the following procedures and Figure 4-42.

1. Remove the two M2.5x4 black flat-head screws for securing the touch pad board.

2. Remove the Touch Pad Board.

M2.5x4 black flat-head screw

Touch pad

Figure 4-42 Removing the touch pad board

Installing the Touch Pad Board

Install the Touch Pad Board according to the following procedures and Figure 4-42.

1. Place the touch pad board in the correct position.

2. Secure the touch pad board with the two M2.5x4 black flat-head screws.

Equium A60/ Satellite A60/ Pro A60/ A65 Maintenance Manual 4-61

6000 1 ?

Appendices

Appendices

App-ii

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Appendix Contents

Appendices

Appendix A Handling the LCD Module..............................................................................A-1

Appendix B Board Layout ...................................................................................................B-1

B.1

B.2

System Board Front View ........................................................................................B-1

System Board Back View.........................................................................................B-3

Appendix C Pin Assignments...............................................................................................C-1

System Board ......................................................................................................................... C-2

C.1

C.2

CN1 Parallel Connector (25-Pin)........................................................................... C-2

CN2 External Monitor Connector (15-Pin) .............................................................. C-2

C.3

C.4

C.5

C.6

CN3 RJ45 (12-Pin+4LED) ..................................................................................... C-3

CN5 USB I/F Connector-A+B (8-Pin).................................................................... C-3

CN6 TV OUT Connector (4-Pin)............................................................................ C-3

CN7 PC Card Slot Connector (68-Pin)................................................................... C-4

C.7

C.8

CN9 SD/MS Connector (23-Pin)............................................................................ C-5

CN11 USB I/F Connector-C (4-Pin) ...................................................................... C-6

C.9 CN12 ODD Bay Connector (52-Pin) ...................................................................... C-6

C.10 CN13 LCD/FL Inverter Connector (42-Pin)............................................................ C-7

C.11 CN14 Cooling Module Connector (1) (3-Pin)......................................................... C-7

C.12 CN15 Cooling Module Connector (2) (3-Pin)......................................................... C-8

C.13 CN16 Internal KEY Board Connector (34-Pin)...................................................... C-8

C.14 CN18 HDD Connector (44-Pin) ............................................................................. C-9

C.15 CN19 Main Battery Connector (7-Pin).................................................................... C-9

C.16 CN20 Internal Speaker Connector (6-Pin)............................................................ C-10

C.17 CN501 MINI PCI Connector (126-Pin) ............................................................... C-10

C.18 CN502 MDC I/F Connector (30-Pin)...................................................................... C-12

C.19 CN503 Memory Slot Connector (202-Pin).......................................................... C-13

C.20 CN2000 Touch Pad Connector (12-Pin) ............................................................... C-16

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

App-iii

Appendices

C.21 CN2002 LED Connector (24-Pin) ........................................................................ C-16

C.22 JACK1 DC_IN Connector (2-Pin)........................................................................ C-17

C.23 JACK2 Ext_Microphone Connector (6-Pin).......................................................... C-17

C.24 JACK3 Headphone Connector (6-Pin).................................................................. C-17

Appendix D Keyboard Scan/Character Codes .................................................................. D-1

Appendix E Key Layout.......................................................................................................E-1

Appendix F BIOS Rewrite Procedures ............................................................................... F-1

Appendix G EC/KBC Rewrite Procedures ........................................................................ G-1

App-iv

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Appendices

Figures

Figure B-1 Board layout (front) ..............................................................................................B-1

Figure B-2 Board layout (back)..............................................................................................B-3

Figure E-1 CN keyboard .......................................................................................................E-1

Tables

Table B-1 System board connectors (front).......................................................................B-2

Table B-2 System board connectors (back) ......................................................................B-4

Table C-1 Parallel connector pin assignments (25-PIN)................................................... C-2

Table C-2 External monitor connector pin assignments (15-pin) ........................................ C-2

Table C-3 RJ45 (12-Pin+4LED) ..................................................................................... C-3

Table C-4 USB I/F connector pin assignments (8-Pin)...................................................... C-3

Table C-5 TV OUT connector pin assignments (4-pin).................................................... C-3

Table C-6 PC card slot connector pin assignments (68-pin) (1/2) ..................................... C-4

Table C-7 SD/MS connector pin assignments (23-Pin)..................................................... C-5

Table C-8 USB I/F connector pin assignments (4-Pin)...................................................... C-6

Table C-9 ODD bay connector pin assignments (52-Pin).................................................. C-6

Table C-10 LCD/FL Inverter connector pin assignments (42-Pin) ................................. C-7

Table C-11 Cooling Module connector (1) pin assignments (3-Pin).................................... C-7

Table C-12 Cooling Module connector (2) pin assignments (3-Pin)................................... C-8

Table C-13 Key Board I/F connector pin assignments (34-Pin) .......................................... C-8

Table C-14 HDD connector pin assignments (44-Pin) ........................................................ C-9

Table C-15 Main battery connector pin assignments (7-Pin) ............................................... C-9

Table C-16 Internal speaker connector pin assignments (6-Pin) ....................................... C-10

Table C-17 MINI PCI connector pin assignments (126-Pin) (1/3).................................... C-10

Table C-18 MDC I/F connector pin assignments (30-Pin) ................................................ C-12

Table C-19 Memory slot connector pin assignments (202-PIN) (1/3) ............................ C-13

Table C-20 Touch Pad connector pin assignments (12-Pin) .............................................. C-16

Table C-21 LED connector pin assignments (24-Pin) ....................................................... C-16

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

App-v

Appendices

Table C-22 DC_IN connector pin assignments (2-Pin).................................................... C-17

Table C-23 Ext_microphone connector pin assignments (6-Pin)........................................ C-17

Table C-24 Headphone connector pin assignments (6-Pin) ............................................... C-17

Table D-1 Scan codes (set 1 and set 2)............................................................................ D-1

Table D-2 Scan codes with left Shift key.......................................................................... D-5

Table D-3 Scan codes in Numlock mode ......................................................................... D-6

Table D-4 Scan codes with Fn key .................................................................................. D-6

Table D-5 Scan codes in overlay mode ............................................................................ D-7

Table D-6 No.124 key scan code.................................................................................... D-7

Table D-7 No.126 key scan code.................................................................................... D-8

App-vi

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Apx. A Handling the LCD Module Appendices

Appendix A

Appendix A Handling the LCD Module

Precautions for handling the LCD module

The LCD module can be easily damaged during assembly or disassembly. Observe the following precautions when handling the LCD module:

1. When installing the LCD module in the LCD cover, be sure to seat it so that it is properly aligned and maximum visibility of the display is maintained.

2. Be careful to align the four holes at the right side and left side of the LCD module with the corresponding holes in the LCD cover before securing the module with four screws. Do not force the module into place, because stress can affect its performance. Also, the panel’s polarized surface is easily scarred, so be carefully when handling it.

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

A-1

Appendices

Apx. A Handling the LCD Module

3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again.

If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to a cloth and then wipe the panel’s surface. Do not apply cleanser directly to the panel. Also, never scratch the surface.

4. If water or other liquid is left on the panel’s surface for a long period, it can change the screen’s tint or stain it. Be sure to quickly wipe off any liquid.

A-2

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Apx. A Handling the LCD Module Appendices

5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks.

6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module.

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

A-3

Appendices

Apx. A Handling the LCD Module

7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods.

8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage.

A-4

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Apx. A Handling the LCD Module

9. Do not disassemble the LCD module. Disassembly can cause malfunctions.

Appendices

10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime). These materials can release gas that can damage the panel’s polarization.

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

A-5

R

Q

P

S

O

N

T

Apx. B Board Layout

Appendix B

Appendix B Board Layout

B.1 System Board Front View

Figure B-1 Board layout (front)

A

B C

Appendices

\_

D

E

F

G

I

H

J

M L

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

K

B-1

K’

L

M

N

G’

H’

I’

J’

Mark

A’

B’

C’

D’

E’

F’

S

T

O

P

Q

R

Appendices

Table B-1 System board connectors (front)

CN5

CN3

CN10

CN6

CN11

JACK2

JACK3

CN8

Number

CN13

CN12

CN9

CN4

CN1

CN2

CN17

CN16

CN19

CN22

CN15

CN14

Name

LCD/FL Inverter Connector

ODD Bay Connector

SD/MS Connector

IEEE 1394 Connector

Parallel Connector

External Monitor Connector

USB I/F Connector B

RJ45 (LAN)/RJ11 Connector

CPU Connector

S-Video Connector

USB I/F Connector C

Ext_Microphone Connector

Headphone Connector

HDD

Connector

LED Status and IR Connector

Internal

Keyboard Connector

Battery Bay Connector

BIOS Chip Connector

FAN 2

FAN 1

Apx. B Board Layout

B-2

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Apx. B Board Layout

Figure B-2 Board layout ( back )

Appendices

D

A

C B

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

B-3

Mark

A’

B’

C’

D’

Appendices Apx. B Board Layout

Table B-2 System board ICs and connectors (back)

Number

CN501

CN502

CN504

CN503

Name

MINI PCI Connector

MDC Connector

Serial Connector

Memory Slot A Connector

B-4

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Apx. C Pin Assignments

Appendices

Appendix C Pin Assignments...............................................................................................C-1

System Board ......................................................................................................................... C-2

C.1 CN1 Parallel Connector (25-Pin) .............................................................................. C-2

C.2 CN2 External Monitor Connector (15-Pin).................................................................. C-2

C.3 CN3 RJ45 (12-Pin+4LED)......................................................................................... C-3

C.4 CN5 USB I/F Connector-A+B (8-Pin) ....................................................................... C-3

C.5 CN6 TV OUT Connector (4-Pin) ............................................................................... C-3

C.6 CN7 PC Card Slot Connector (68-Pin) ...................................................................... C-4

C.7 CN9 SD/MS Connector (23-Pin) ............................................................................... C-5

C.8 CN11 USB I/F Connector-C (4-Pin).......................................................................... C-6

C.9 CN12 ODD Bay Connector (52-Pin).......................................................................... C-6

C.10 CN13 LCD/FL Inverter Connector (42-Pin) ............................................................... C-7

C.11 CN14 Cooling Module Connector (1) (3-Pin) ............................................................ C-7

C.12 CN15 Cooling Module Connector (2) (3-Pin) ............................................................ C-8

C.13 CN16 Internal KEY Board Connector (34-Pin) ......................................................... C-8

C.14 CN18 HDD Connector (44-Pin)................................................................................. C-9

C.15 CN19 Main Battery Connector (7-Pin) ....................................................................... C-9

C.16 CN20 Internal Speaker Connector (6-Pin) ............................................................... C-10

C.17 CN501 MINI PCI Connector (126-Pin)................................................................... C-10

C.18 CN502 MDC I/F Connector (30-Pin)...................................................................... C-12

C.19 CN503 Memory Slot Connector (202-Pin) ............................................................. C-13

C.20 CN2000 Touch Pad Connector (12-Pin)................................................................... C-16

C.21 CN2002 LED Connector (24-Pin)............................................................................ C-16

C.22 JACK1 DC_IN Connector (2-Pin) ........................................................................... C-17

C.23 JACK2 Ext_Microphone Connector (6-Pin) ............................................................. C-17

C.24 JACK3 Headphone Connector (6-Pin) ..................................................................... C-17

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

C-1

Appendices

Apx. C Pin Assignments

Appendix C

Appendix C Pin Assignments

System Board

C.1 CN1 Parallel Connector (25-Pin)

Table C-1 Parallel connector pin assignments (25-PIN)

Pin No.

1

3

5

7

9

11

13

15

Pin No.

1

11

13

15

17

3

5

7

9

19

21

23

25

Signal Name

/STRB#_5R

/PDATA(1)_R

/PDATA(3)_R

/PDATA(5)_R

/PDATA(7)_R

/BUSY#_5R

/SLCT_5R

/ERROR#_5R

/SLCTIN#_5R

DGND

DGND

DGND

DGND

I/O

O

I

I

I

O

I/O

I/O

I/O

I/O

-

-

-

-

Pin No.

2

12

14

16

18

4

6

8

10

20

22

24

Signal Name

/PDATA(0)_R

/PDATA(2)_R

/PDATA(4)_R

/PDATA(6)_R

/ACK#_5R

/PE_5R

/ALF#_5R

/PINIT#_5R

DGND

DGND

DGND

DGND

C.2 CN2 External Monitor Connector (15-Pin)

Table C-2 External monitor connector pin assignments (15-pin)

Signal Name

RED

BLUE

VGA GND

VGA GND

+V5S

NC

CRT_HSYNC

DDCCLK

I/O

O

O

-

-

-

-

O

I/O

Pin No.

2

4

6

8

10

12

14

Signal Name

GREEN

NC

VGA GND

VGA GND

VGA GND

DDC DATA

CRT_VSYNC

I/O

O

I/O

O

I/O

I/O

I

O

O

-

I/O

I/O

I/O

I

-

-

-

C-2

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Apx. C Pin Assignments

C.3 CN3 RJ45 (12-Pin+4LED)

Table C-3 RJ45 (12-Pin+4LED)

Pin No.

1

A1

A3

A5

A7

A9

A11

B1

Signal Name

G

/TX+_TRAN

/RX+_TRAN

NC 1

NC 2

LED_LAN#

LED_LANACT#

/MDMTIP

I/O

-

O

I

-

-

I

I

I/O

Pin No.

2

A2

A4

A6

A8

A10

A12

B2

C.4 CN5 USB I/F Connector-A+B (8-Pin)

Table C-4 USB I/F connector pin assignments (8-Pin)

Signal Name

G

/TX-_TRAN

NC 0

/RX-_TRAN

NC 3

LED GP

+V3_LAN

/MDMRNG

Pin No.

1

3

5

7

G1

G3

Signal Name

USBVCC1

/USB_PP1_L

USBVCC1

/USB_PP0_L

DGND

DGND

I/O

-

I/O

-

I/O

-

-

Pin No.

2

4

6

8

G2

G4

C.5 CN6 TV OUT Connector (4-Pin)

Table C-5 TV OUT connector pin assignments (4-pin)

Signal Name

/USB_PN1_L

DGND

/USB_PN0_L

DGND

DGND

DGND

Pin No.

1

3

G1

Signal Name

DGND

LUMA_Y

DGND

I/O

-

I

-

Pin No.

2

4

G2

Signal Name

DGND

CHROMA_C

DGND

Appendices

I/O

-

I

-

I/O

-

O

I

I

-

I

I

I/O

I/O

I/O

-

I/O

-

-

-

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

C-3

Appendices

Apx. C Pin Assignments

Signal Name

DGND

/A_CDAT(4)

/A_CDAT(6)

/A_CE1#

/A_OE#

/A_CADR(9)

/A_CADR(13)

/A_WE#

ACARDVCC

/A_CADR(16)_R

/A_CADR(12)

/A_CADR(6)

/A_CADR(4)

/A_CADR(2)

/A_CADR(0)

/A_CDAT(1)

/A_WP_IO16#

DGND

/A_CDAT(11)

/A_CDAT(13)

/A_CDAT(15)

/A_VS1

/A_IOWR#

/A_CADR(18)

/A_CADR(20)

ACARDVCC

/A_CADR(22)

/A_CADR(24)

/A_VS2

/A_WAIT#

/A_REG#

/A_BVD1_STSCHG_RI

/A_CDAT(9)

/A_CD2#

Pin No.

1

59

61

63

65

67

51

53

55

57

43

45

47

49

35

37

39

41

27

29

31

33

19

21

23

25

11

13

15

17

3

5

7

9

C.6 CN7 PC Card Slot Connector (68-Pin)

Table C-6 PC card slot connector pin assignments (68-pin) (1/2)

I/O

-

O

I

O

I/O

O

-

I/O

I/O

I/O

I/O

I

I/O

I/O

-

I/O

I/O

I/O

I/O

I/O

I/O

O

I/O

I/O

I/O

I/O

I/O

I/O

I

-

I/O

I/O

I

I

Pin No.

2

60

62

64

66

68

52

54

56

58

44

46

48

50

36

38

40

42

28

30

32

34

20

22

24

26

12

14

16

18

4

6

8

10

Signal Name

/A_CDAT(3)

/A_CD1#

/A_CDAT(12)

/A_CDAT(14)

/A_CE2#

/A_IORD#

/A_CADR(17)

/A_CADR(19)

/A_CADR(21)

ACARDVPP

/A_CADR(23)

/A_CADR(25)

/A_RESET

/A_INPACK#

/A_BVD2_SPKR

/A_CDAT(8)

/A_CDAT(10)

DGND

/A_CDAT(5)

/A_CDAT(7)

/A_CADR(10)

/A_CADR(11)

/A_CADR(8)

/A_CADR(14)

/A_RDY_IREQ

ACARDVPP

/A_CADR(15)

/A_CADR(7)

/A_CADR(5)

/A_CADR(3)

/A_CADR(1)

/A_CDAT(0)

/A_CDAT(2)

DGND

I/O

I/O

O

O

I/O

I/O

-

I/O

I/O

I/O

I

I

I/O

I/O

I/O

I/O

I/O

I/O

I

I/O

I/O

I/O

-

I/O

I/O

I/O

I/O

I/O

I/O

O

-

I/O

I/O

I/O

I/O

C-4

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Apx. C Pin Assignments

Table C-6 PC card slot connector pin assignments (68-pin) (2/2)

G1

G11

G13

G15

G17

G19

G20

G4

G6

G8

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

-

-

-

-

-

-

-

-

-

-

G10

G12

G14

G16

G18

G2

G3

G5

G7

G9

C.7 CN9 SD/MS Connector (23-Pin)

Table C-7 SD/MS connector pin assignments (23-Pin)

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

Pin No.

13

15

17

19

1

3

5

7

9

11

21

23

Signal Name

/SD_DAT3

DGND

/SD_MS_CLK

/SD_DAT0

/SD_DAT2

DGND

DGND

/MS_BS

/MS_DATA0

/MS_INS#

/MS_CLK

DGND

I/O

-

I/O

I/O

I

I/O

-

I

I/O

I/O

-

I

-

Pin No.

14

16

18

20

22

2

4

6

8

10

12

Signal Name

/SD_CMD

VCC_SD

DGND

/SD_DAT1

/SD_CD#

/SD_WP

DGND

MS_DATA1

MS_DATA2

MS_DATA3

VCC_SD

Appendices

-

-

-

-

-

-

-

-

-

-

I/O

-

I

I

I

-

O

-

-

I/O

O

O

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

C-5

Appendices

Apx. C Pin Assignments

C.8 CN11 USB I/F Connector-C (4-Pin)

Table C-8 USB I/F connector pin assignments (4-Pin)

Pin No. Signal Name I/O Pin No. Signal Name

1

3

G1

USBVCC2

/USB_PP2_L

DGND

-

I/O

-

2

4

G2

C.9 CN12 ODD Bay Connector (52-Pin)

/USB_PN2_L

DGND

DGND

Table C-9 ODD bay connector pin assignments (52-Pin)

Pin No.

1

25

27

29

31

17

19

21

23

9

11

13

15

3

5

7

41

43

45

47

33

35

37

39

49

51

Signal Name

/A_CD_L

/A_CD_GND

NB_RST#

/SDD_R(7)

/SDD_R(6)

/SDD_R(5)

/SDD_R(4)

/SDD_R(3)

/SDD_R(2)

/SDD_R(1)

/SDD_R(0)

DGND

/SDIOW#_3_R

/SDIORDY_35_R

/IRQ15_3_R

/SDA_R(1)

/SDA_R(0)

/SDCS1#_3_R

/MBDASP#_5

+V5S

+V5S

DGND

DGND

DGND

NC

DGND

I/O

O

I/O

I/O

O

I

I/O

I/O

I/O

-

-

I

I/O

I/O

I/O

I/O

I/O

-

-

-

-

-

-

I

I

I

-

Pin No.

2

26

28

30

32

18

20

22

24

10

12

14

16

4

6

8

42

44

46

48

34

36

38

40

50

52

Signal Name

/A_CD_R

NC

/SDD_R(8)

/SDD_R(9)

/SDD_R(10)

/SDD_R(11)

/SDD_R(12)

/SDD_R(13)

/SDD_R(14)

/SDD_R(15)

/SDDRQ_35_R

/SDIOR#_3_R

DGND

/SDDACK#_35_R

NC

NC

/SDA_R(2)

/SDCS3#_3_R

+V5S

+V5S

+V5S

DGND

DGND

DGND

NC

DGND

I/O

O

-

I

-

-

I/O

I/O

O

I/O

-

I/O

I/O

I/O

I/O

I/O

I/O

-

-

-

-

-

-

I

I

-

-

I/O

I/O

-

-

C-6

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Apx. C Pin Assignments

Appendices

C.10 CN13 LCD/FL Inverter Connector (42-Pin)

Table C-10 LCD/FL Inverter connector pin assignments (42-Pin)

Pin No.

1

27

29

33

35

19

21

23

25

11

13

15

17

3

5

7

9

37

39

41

Signal Name

/LCM_ID0

/LCM_ID1

/LCM_ID2

DGND

DGND

/TXOUTL0-

/TXOUTL1-

/TXOUTL2-

/TXCLKOUTL-

DGND

/TXOUTU0-

/TXOUTU1-

/TXOUTU2-

/TXCLKOUTU-

DGND

+V5S

+V5S

/BLON#

DGND

DGND

Pin No.

2

28

30

34

36

20

22

24

26

12

14

16

18

4

6

8

10

38

40

42

I/O

I

O

-

-

-

-

O

O

O

O

-

-

O

O

O

O

I

I

-

-

Signal Name

+V3SLCM

+V3SLCM

+V3S

/LCM_DDCCLK

/LCM_DDCDATA

/TXOUTL0+

/TXOUTL1+

/TXOUTL2+

/TXCLKOUTL+

DGND

/TXOUTU0+

/TXOUTU1+

/TXOUTU2+

/TXCLKOUTU+

DGND

+V5S

/INV_PWM_3

DGND

DGND

DGND

C.11 CN14 Cooling Module Connector (1) (3-Pin)

Table C-11 Cooling Module connector (1) pin assignments (3-Pin)

I/O

-

O

-

-

O

-

O

O

O

-

-

-

O

O

O

O

-

-

O

I/O

Pin No.

1

3

Signal Name

+V5S

/FAN_TACH1

I/O

-

I

Pin No.

2

Signal Name

DGND

I/O

-

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

C-7

Appendices

Apx. C Pin Assignments

C.12 CN15 Cooling Module Connector (2) (3-Pin)

Table C-12 Cooling Module connector (2) pin assignments (3-Pin)

Pin No.

1

3

Signal Name

+V5S

/FAN_TACH2

I/O

-

I

Pin No.

2

Signal Name

DGND

C.13 CN16 Internal KEY Board Connector (34-Pin)

Table C-13 Key Board I/F connector pin assignments (34-Pin)

I/O

-

Pin No.

1

23

25

27

29

31

33

15

17

19

21

3

5

7

9

11

13

Signal Name

+V5S

NC

NC

/SCAN_OUT(4)

/SCAN_IN(2)

/SCAN_OUT(1)

/SCAN_IN(0)

/SCAN_OUT(5)

/SCAN_IN(5)

/SCAN_IN(4)

/SCAN_OUT(7)

/SCAN_IN(7)

/SCAN_OUT(9)

/SCAN_OUT(11)

/SCAN_OUT(14)

+V5S

/SCROLL_LED#_3

I/O

-

I

O

O

O

-

O

O

I

I

O

-

-

O

I

O

I

Pin No.

2

24

26

28

30

32

34

16

18

20

22

4

6

8

10

12

14

Signal Name

NC

NC

+V5S

/SCAN_OUT(2)

/SCAN_IN(1)

/SCAN_OUT(0)

/SCAN_IN(3)

/SCAN_OUT(6)

/SCAN_IN(6)

/SCAN_OUT(12)

/SCAN_OUT(3)

/SCAN_OUT(13)

/SCAN_OUT(8)

/SCAN_OUT(10)

/SCAN_OUT(15)

/CAPS_LED#_3

/NUM_LED#_3

I/O

-

O

O

O

O

O

O

O

I

O

O

-

-

O

I

O

I

C-8

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Apx. C Pin Assignments

C.14 CN18 HDD Connector (44-Pin)

Table C-14 HDD connector pin assignments (44-Pin)

Pin No.

1

27

29

31

33

19

21

23

25

11

13

15

17

3

5

7

9

35

37

39

41

43

G1

Signal Name

NB_RST#

/PDD_R(7)

/PDD_R(6)

/PDD_R(5)

/PDD_R(4)

/PDD_R(3)

/PDD_R(2)

/PDD_R(1)

/PDD_R(0)

DGND

/PDDRQ_35_R

/PDIOW#_3_R

/PDIOR#_3_R

/PDIORDY_35_R

/PDDACK#_35_R

/IRQ14_3_R

/PDA_R(1)

/PDA_R(0)

/PDCS1#_3_R

/HDDASP#_5

+V5S

DGND

DGND

Pin No.

2

28

30

32

34

20

22

24

26

12

14

16

18

4

6

8

10

36

38

40

42

44

G2

I/O

I

I/O

O

I

I

-

O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I

I

I

-

-

-

C.15 CN19 Main Battery Connector (7-Pin)

Table C-15 Main battery connector pin assignments (7-Pin)

Signal Name

DGND

/PDD_R(8)

/PDD_R(9)

/PDD_R(10)

/PDD_R(11)

/PDD_R(12)

/PDD_R(13)

/PDD_R(14)

/PDD_R(15)

NC

DGND

DGND

DGND

NC

DGND

NC

DGND

/PDA_R(2)

/PDCS3#_3_R

DGND

+V5S

NC

DGND

Pin No.

1

3

5

7

Signal Name

+VBAT

BATT_SCL

BATT_THRM

DGND

I/O

-

I/O

O

-

Pin No.

2

4

6

Signal Name

+VBAT

BATT_SDA

DGND

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

I/O

-

-

-

-

-

-

-

-

-

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I

I

-

-

-

-

Appendices

I/O

-

I/O

-

C-9

Appendices

Apx. C Pin Assignments

C.16 CN20 Internal Speaker Connector (6-Pin)

Table C-16 Internal speaker connector pin assignments (6-Pin)

Pin No.

1

3

5

Signal Name

/SPK_OUT_L-

/SPK_OUT_R-

DGND

I/O

O

O

-

Pin No.

2

4

6

Signal Name

/SPK_OUT_L+

/SPK_OUT_R+

DGND

C.17 CN501 MINI PCI Connector (126-Pin)

Table C-17 MINI PCI connector pin assignments (126-Pin) (1/3)

Pin No.

1

25

27

29

31

17

19

21

23

33

35

9

11

13

15

3

5

7

Signal Name

NC

NC

NC

NC

NC

NC

WLON_LED#

DGND

/PIRQB#_3

+V3

NC

DGND

/CLK_MINIPCI_EXTR

DGND

/MPCIREQ0#_3

+V3

/PCI_AD(31)

/PCI_AD(29)

I/O

-

O

-

I

-

|

-

-

-

I/O

I/O

-

-

O

-

-

-

-

Pin No.

2

26

28

30

32

18

20

22

24

34

36

10

12

14

16

4

6

8

Signal Name

NC

NC

NC

NC

NC

NC

NC

NC

+V5S

/PIRQB#_3

NC

+V3

/PCI_RESET#_3

+V3

/MPCIGNT0#_3

DGND

/PCI_PME#_3

NC

I/O

-

O

-

O

-

I

-

-

I

-

-

-

-

-

-

-

-

-

I/O

O

O

-

C-10

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Apx. C Pin Assignments

Appendices

Table C-17 MINI PCI connector pin assignments (126-Pin) (2/3)

GND

/PCI_PERR#_3

/PCI_CBE#(1)

/PCI_AD(14)

DGND

/PCI_AD(12)

/PCI_AD(10)

DGND

/PCI_AD(8)

/PCI_AD(7)

+V3

/PCI_AD(5)

NC

/PCI_AD(3)

+V5S

/PCI_AD(1)

DGND

NC

/PCI_AD(27)

/PCI_AD(25)

NC

/PCI_CBE#(3)

/PCI_AD(23)

DGND

/PCI_AD(21)

/PCI_AD(19)

DGND

/PCI_AD(17)

/PCI_CBE#(2)

/PCI_IRDY#_3

+V3

/CLKRUN#_3

/PCI_SERR#_3

DGND

37

95

97

99

101

103

87

89

91

93

79

81

83

85

71

73

75

77

63

65

67

69

55

57

59

61

47

49

51

53

39

41

43

45

-

I/O

-

I/O

-

-

I/O

-

I/O

-

I/O

I/O

-

I/O

O

O

I/O

-

-

I/O

O

-

-

I/O

I/O

I/O

I/O

-

I/O

I/O

I/O

I/O

-

O

38

96

98

100

102

104

88

90

92

94

80

82

84

86

72

74

76

78

64

66

68

70

56

58

60

62

48

50

52

54

40

42

44

46

/PCI_AD(30)

+V3

/PCI_AD(28)

/PCI_AD(26)

/PCI_AD(24)

/PCI_AD(20)

DGND

/PCI_AD(22)

/PCI_AD(20)

/PCI_PAR_3

/PCI_AD(18)

/PCI_AD(16)

DGND

/PCI_FRAME#_3

/PCI_TRDY#_3

/PCI_STOP#_3

+V3

/PCI_DEVSEL#_3

DGND

/PCI_AD(15)

/PCI_AD(13)

/PCI_AD(11)

DGND

/PCI_AD(9)

/PCI_CBE#(0)

+V3

/PCI_AD(6)

/PCI_AD(4)

/PCI_AD(2)

/PCI_AD(0)

NC

NC

DGND

DGND

I/O

I/O

-

-

-

-

-

I/O

I/O

I/O

I/O

-

I/O

I/O

O

-

I/O

I/O

I/O

I/O

I/O

-

I/O

I/O

I/O

-

I/O

-

I/O

I/O

-

I/O

I/O

I/O

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

C-11

Appendices

Apx. C Pin Assignments

Pin No.

1

19

21

23

25

27

29

11

13

15

17

3

5

7

9

Table C-17 MINI PCI connector pin assignments (126-Pin) (3/3)

105

107

109

111

113

115

117

119

121

123

125

NC

NC

NC

NC

DGND

NC

DGND

DGND

NC

NC

DGND

-

-

-

-

-

-

-

-

-

-

-

106

108

110

112

114

116

118

120

122

124

126

NC

NC

NC

NC

DGND

NC

DGND

DGND

NC

+V3

DGND

C.18 CN502 MDC I/F Connector (30-Pin)

Table C-18 MDC I/F connector pin assignments (30-Pin)

Signal Name

NC

GND

NC

NC

NC

NC

NC

GND

MDC

GND

NC

/A97SDO

/A97RST#

GND

GND

I/O

-

-

-

I/O

I/O

-

-

-

-

-

I/O

-

-

-

-

Pin No.

2

20

22

24

26

28

30

12

14

16

18

4

6

8

10

Signal Name

GND

/PHONE

NC

GND

NC

NC

NC

MDC

NC

GND

/A97SYC

/A97DI1

/A97DI1

GND

/BITCLK_3_MDC

I/O

-

-

I/O

I/O

I/O

-

I/O

-

-

I/O

-

I/O

-

-

-

-

-

-

-

-

-

-

-

-

-

-

C-12

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Apx. C Pin Assignments

Appendices

C.19 CN503 Memory Slot Connector (202-Pin)

Table C-19 Memory slot connector pin assignments (202-PIN) (1/3)

Pin No.

1

49

51

53

55

57

59

41

43

45

47

33

35

37

39

25

27

29

31

17

19

21

23

9

11

13

15

3

5

7

61

63

65

67

Signal Name

/SM_VREF

DGND

/M_DATA_R(0)

/M_DATA_R(1)

+V2.5'

/M_DQS_R(0)

/M_DATA_R(2)

DGND

/M_DATA_R(3)

/M_DATA_R(8)

+V2.5'

/M_DATA_R(9)

/M_DQS_R(1)

DGND

/M_DATA_R(10)

/M_DATA_R(11)

+V2.5'

/M_CLK_DDR0

/M_CLK_DDR0#

DGND

/M_DATA_R(16)

/M_DATA_R(17)

+V2.5'

/M_DQS_R(2)

/M_DATA_R(18)

DGND

/M_DATA_R(19)

/M_DATA_R(24)

+V2.5'

/M_DATA_R(25)

/M_DQS_R(3)

DGND

/M_DATA_R(26)

/M_DATA_R(27)

I/O

I

I/O

-

I/O

I/O

-

I/O

I/O

I/O

-

I/O

-

I/O

I/O

-

I/O

-

I/O

I/O

I/O

I/O

-

I/O

-

I/O

I/O

-

I/O

I/O

-

I/O

-

I/O

I/O

Pin No.

2

50

52

54

56

58

60

42

44

46

48

34

36

38

40

26

28

30

32

18

20

22

24

10

12

14

16

4

6

8

62

64

66

68

Signal Name

/SM_VREF

DGND

/M_DATA_R(4)

/M_DATA_R(5)

+V2.5'

/M_DM_R(0)

/M_DATA_R(6)

DGND

/M_DATA_R(7)

/M_DATA_R(12)

+V2.5'

/M_DATA_R(13)

/M_DM_R(1)

DGND

/M_DATA_R(14)

/M_DATA_R(15)

+V2.5'

+V2.5'

DGND

DGND

/M_DATA_R(20)

/M_DATA_R(21)

+V2.5'

/M_DM_R(2)

/M_DATA_R(22)

DGND

/M_DATA_R(23)

/M_DATA_R(28)

+V2.5'

/M_DATA_R(29)

/M_DM_R(3)

DGND

/M_DATA_R(30)

/M_DATA_R(31)

I/O

I

I/O

-

I/O

I/O

-

I/O

I/O

I/O

-

I

-

-

-

-

I

-

I/O

I/O

I/O

I/O

-

I/O

-

I/O

I/O

-

I

I/O

-

I

-

I/O

I/O

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

C-13

Appendices

Apx. C Pin Assignments

69

119

121

123

125

127

129

131

133

135

103

105

107

109

111

113

115

117

95

97

99

101

87

89

91

93

79

81

83

85

71

73

75

77

+V2.5'

DGND

/M_A(7)

/M_A(5)

/M_A(3)

/M_A(1)

+V2.5'

/M_A(10)

/M_A(13)

/M_WE_R#

/M_CS0_R#

/M_A(15)

DGND

/M_DATA_R(32)

/M_DATA_R(33)

+V2.5'

/M_DQS_R(4)

/M_DATA_R(34)

DGND

DGND

DGND

DGND

DGND

+V2.5'

DGND

NC

DGND

+V2.5’

DGND

+V2.5'

/M_CKE1_R#

NC

/M_A(12)

/M_A(9)

Table C-19 Memory slot connector pin assignments (202-PIN) (2/3)

-

-

-

-

-

-

-

-

-

-

I/O

-

I/O

I/O

-

I/O

I/O

I/O

I/O

-

I/O

I/O

-

-

-

I/O

I/O

-

I/O

I/O

I/O

I/O

I/O

-

70

120

122

124

126

128

130

132

134

136

104

106

108

110

112

114

116

118

96

98

100

102

88

90

92

94

80

82

84

86

72

74

76

78

+V2.5'

DGND

/M_A(6)

/M_A(4)

/M_A(2)

/M_A(0)

+V2.5'

/M_A(14)

/M_RAS_R#

/M_CAS_R#

/M_CS1_R#

NC

DGND

/M_DATA_R(36)

/M_DATA_R(37)

+V2.5'

/M_DM_R(4)

/M_DATA_R(38)

DGND

DGND

DGND

NC

DGND

+V2.5'

DGND

NC

DGND

DGND

+V2.5'

+V2.5'

/M_CKE0_R#

DGND

/M_A(11)

/M_A(8)

-

I/O

I/O

-

I

I/O

I/O

I/O

-

-

I/O

-

I/O

I/O

-

I/O

I/O

I/O

I/O

-

I/O

I/O

-

-

-

-

-

-

-

-

-

-

-

-

C-14

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Apx. C Pin Assignments

Appendices

Table C-19 Memory slot connector pin assignments (202-PIN) (3/3)

DGND

/M_DATA_R(50)

DGND

/M_DATA_R(51)

/M_DATA_R(56)

+V2.5'

/M_DATA_R(57)

/M_DQS_R(7)

DGND

/M_DATA_R(58)

/M_DATA_R(59)

+V2.5'

/SMBDATA_3

/SMBCLK_3

+V3S'

+V2.5’

DGND

/M_DATA_R(35)

/M_DATA_R(40)

+V2.5'

/M_DATA_R(41)

/M_DQS_R(5)

DGND

/M_DATA_R(42)

/M_DATA_R(43)

+V2.5'

+V2.5'

DGND

DGND

/M_DATA_R(48)

/M_DATA_R(49)

+V2.5'

/M_DQS_R(6)

137

187

189

191

193

195

197

199

201

171

173

175

177

179

181

183

185

155

157

159

161

163

165

167

169

139

141

143

145

147

149

151

153

138

188

190

192

194

196

198

200

202

172

174

176

178

180

182

184

186

156

158

160

162

164

166

168

170

140

142

144

146

148

150

152

154

-

I/O

-

-

-

I/O

I/O

-

I/O

-

I/O

I/O

-

I/O

-

I/O

I/O

I/O

I/O

-

I

-

-

-

-

I/O

-

I/O

I/O

I/O

I/O

-

I/O

DGND

/M_DATA_R(54)

DGND

/M_DATA_R(55)

/M_DATA_R(60)

+V2.5'

/M_DATA_R(61)

/M_DM_R(7)

DGND

/M_DATA_R(62)

/M_DATA_R(63)

+V2.5'

DGND

DGND

DGND

NC

DGND

/M_DATA_R(39)

/M_DATA_R(44)

+V2.5'

/M_DATA_R(45)

/M_DM_R(5)

DGND

/M_DATA_R(46)

/M_DATA_R(47)

+V2.5'

/M_CLK_DDR1#

/M_CLK_DDR1

DGND

/M_DATA_R(52)

/M_DATA_R(53)

+V2.5'

/M_DM_R(6)

-

-

-

-

-

I/O

I/O

-

-

-

I/O

I

-

I/O

-

I/O

I/O

I/O

I/O

-

I

-

I/O

I/O

-

I

-

I/O

I/O

I/O

I/O

-

I/O

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

C-15

Appendices

Apx. C Pin Assignments

C.20 CN2000 Touch Pad Connector (12-Pin)

Table C-20 Touch Pad connector pin assignments (12-Pin)

Pin No.

1

3

5

7

9

11

G1

Signal Name

/IM_CLK_CN

/IM_DAT_CN

/LEFT_CN

/RIGHT_CN

PGND

NC

PGND

I/O

I/O

I/O

I

I

-

-

-

Pin No.

2

4

6

8

10

12

G2

C.21 CN2002 LED Connector (24-Pin)

Table C-21 LED connector pin assignments (24-Pin)

Signal Name

/IM_CLK_CN

/IM_DAT_CN

/LEFT_CN

/RIGHT_CN

PGND

+V5S_CN

PGND

Pin No.

1

13

15

17

19

21

23

G1

3

5

7

9

11

Signal Name

+V3A_CN

/DCIN_GLED#_CN

/BAT0_GLED#_CN

+V5S_CN

+V3S_CN

/WLON_LED#_CN

/PWR_OLED#_CN

/IM_CLK_CN

/IR_TX_CN

/IR_SD_CN

PGND

PGND

PGND

I/O

-

-

-

-

O

I/O

O

I

O

O

-

-

O

Pin No.

2

14

16

18

20

22

24

G2

4

6

8

10

12

Signal Name

/DCIN_OLED#_CN

/BAT0_OLED#_CN

+V5S_CN

/IDELED#_CN

+V3S_CN

+V3_CN

/PWR_GLED#_CN

/IM_DAT_CN

/IR_RX_CN

PGND

PGND

PGND

PGND

I/O

I/O

I/O

I

I

-

-

-

I/O

O

-

-

-

O

I/O

I

-

O

-

O

-

-

C-16

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Apx. C Pin Assignments

C.22 JACK1 DC_IN Connector (2-Pin)

Table C-22 DC_IN connector pin assignments (2-Pin)

Pin No.

1

G1

G3

Signal Name

/+VADPTR

DGND

DGND

I/O

-

-

-

Pin No.

2

G2

G4

Signal Name

DGND

DGND

DGND

C.23 JACK2 Ext_Microphone Connector (6-Pin)

Table C-23 Ext_microphone connector pin assignments (6-Pin)

Pin No.

1

3

5

G1

Signal Name

MIC

ANAGND

ANAGND

ANAGND

I/O

I/O

-

-

-

Pin No.

2

4

6

G2

Signal Name

AREF

ANAGND

AREF

ANAGND

C.24 JACK3 Headphone Connector (6-Pin)

Table C-24 Headphone connector pin assignments (6-Pin)

Pin No.

1

3

5

G1

Signal Name

ANAGND

SPK_OUT_R+

ANAGND

ANAGND

I/O

-

O

-

-

Pin No.

2

4

6

G2

Signal Name

SPK_OUT_L+

ANAGND

HPS

ANAGND

I/O

-

-

-

I/O

I/O

-

I/O

-

I/O

O

-

O

-

Appendices

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

C-17

Keyboard Scan/Character Codes

Apx. D Keyboard Scan/Character Codes

Appendix D Keyboard Scan/Character Codes

Cap

No.

20

21

22

23

24

25

14

15

16

17

18

19

26

27

28

05

06

07

08

09

10

11

12

13

01

02

03

04

Table D-1 Scan codes (set 1 and set 2) (1/4)

Keytop

P

[ {

] }

R

T

Y

U

I

O

BkSp

Tab

Q

W

E

‘ ~

1 !

2 @

3 #

4 $

5 %

6 ^

7 &

8 *

9 (

0 )

- _

= +

Code set 1

Make Break Make

Code set 2

Break

13

14

15

16

17

18

0E

0F

10

11

12

19

1A

1B

05

06

07

08

09

0A

0B

0C

0D

29

02

03

04

93

94

95

96

97

98

8E

8F

90

91

92

99

9A

9B

85

86

87

88

89

8A

8B

8C

8D

A9

82

83

84

2D

2C

35

3C

43

44

7D

66

0D

15

1D

24

4D

54

5B

25

2E

36

3D

3E

46

45

4E

55

0E

16

1E

26

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

2D

2C

35

3C

43

44

7D

66

0D

15

1D

24

4D

54

5B

25

2E

36

3D

3E

46

45

4E

55

0E

16

1E

26

Note

*2

*2

*2

*2

*2

*2

*2

*2

Appendices

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual D-1

Appendices Keyboard Scan/Character Codes

Table D-1 Scan codes (set 1 and set 2) (2/4)

51

52

53

54

55

56

46

47

48

49

50

57

Cap

No.

34

35

36

37

38

39

29

30

31

32

33

40

41

43

44

45

Keytop

; :

‘ “

Enter

Shift (L)

No.102 key

Z

X

C

V

B

N

M

, <

. >

/ ?

\_

\ |

Caps Lock

A

S

D

F

G

H

J

K

L

Shift (R)

Code set 1

Make Break Make

Code set 2

Break

21

22

23

24

25

26

2B

3A

1E

1F

20

27

28

1C

2A

56

A1

A2

A3

A4

A5

A6

AB

BA

9E

9F

A0

A7

A8

9C

AA

D6

2B

34

33

3B

42

4B

5D

58

1C

1B

23

4C

52

5A

12

61

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

2B

34

33

3B

42

4B

5D

58

1C

1B

23

4C

52

5A

12

61

2C

2D

2E

2F

30

31

32

33

34

35

36

AC

AD

AE

AF

B0

B1

B2

B3

B4

B5

B6

1A

22

21

2A

32

31

3A

41

49

4A

73

59

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

31

3A

41

49

4A

73

1A

22

21

2A

32

59

Note

*2

*2

*2

*5

*3

*2

*2

*2

*2

*2

D-2 Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Keyboard Scan/Character Codes Appendices

Cap

No.

84

85

86

89

110

112

113

114

115

116

117

118

119

120

121

75

76

79

80

81

83

58

60

61

62

Table D-1 Scan codes (set 1 and set 2) (3/4)

Keytop

Code set 1

Make Break Make

Code set 2

Break

Ctrl 1D 9D 14 F0 14

Alt (L)

Space

38

39

B8

B9

11

29

F0

F0

11

29

ALT (R) E0 38 E0 B8 E0 11 E0 F0 11

Esc

F1

F2

F3

F4

F5

Ins

Del

? ?

Home

End

? ?

? ?

PgUp

PgDn

?

? ?

F6

F7

F8

F9

F10

E0

E0

3D

3E

3F

40

41

42

43

44

E0 D3

BD

BE

BF

C0

C1

C2

C3

C4

E0 71

04

0C

03

0B

83

0A

01

09

E0

F0

F0

F0

F0

F0

F0

F0

F0

F0 71

E0 4B E0 CB E0 6B E0 F0 6B

E0 E0 C7 E0 6C E0 F0 6C

E0 4F E0 CF E0 69 E0 F0 69

E0

E0

E0

52

53

47

48

50

4D

01

3B

3C

E0

E0

E0

E0

D2

C8

D0

CD

81

BB

BC

E0

E0

E0

E0

70

75

72

74

E0

E0

E0

E0

76 F0

05 F0

06 F0

F0

F0

F0

F0

70

75

72

E0 49 E0 C9 E0 7D E0 F0 7D

E0 51 E0 D1 E0 7A E0 F0 7A

74

76

05

06

04

0C

03

0B

83

0A

01

09

Note

*1

*1

*1

*1

*3

*1

*1

*1

*1

*1

*1

*3

*3

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual D-3

Appendices Keyboard Scan/Character Codes

Table D-1 Scan codes (set 1 and set 2) (4/4)

Cap Code set 1

No. Keytop Make Break Make

122

123

124 PrintSc *6

F11

F12

57

58

D7

D8

*6

78

7

*6

126 Pause *7

202

203

Fn —

*7

*7

Win E0 5B E0 DB E0 1F

204 App E0 5D E0 DD E0 2F

205 Kat/Hir

206

207

Hen

Muh

70

79

7B

Code set 2

F0

Break

78

F0

*6

*7

E0 F0

E0 F0

1F

2F

F0 70

F0 79

F0 7B

7

Note

*3

*8

*8

*8

*3

*6

*7

*4

Notes:

1. * Scan codes differ by mode.

2. * Scan codes differ by overlay function.

3. * Combination with the Fn key makes different codes.

4. * Fn key does not generate a code by itself.

5. * This key corresponds to key No. 42 in a 102-key model.

6. * Refer to Table D-6, No. 124 key scan code.

7. * Refer to Table D-7, No. 126 key scan code.

8. * 205~207 are for JAPAN keyboard only

D-4 Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Keyboard Scan/Character Codes Appendices

Table D-2 Scan codes with left Shift key

Cap

No.

Key top

Code set 1 Code set 2

Make Break Make Break

55 / E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12

75 INS E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0 12

76 DEL E0 AA E0 53 E0 D3 E0 2A E0 F0 12 E0 71 E0 F0 71 E0 12

79

? ?

E0 AA E0 4B E0 CB E0 2A E0 F0 12 E0 6B E0 F0 6B E0 12

80 Home E0 AA E0 47 E0 C7 E0 2A E0 F0 12 E0 6C E0 F0 6C E0 12

81 End E0 AA E0 4F E0 CF E0 2A E0 F0 12 E0 69 E0 F0 69 E0 12

83

84

? ?

? ?

E0

E0

AA

AA

E0

E0

48

50

E0 C8

E0 D0

E0

E0

2A

2A

E0

E0

F0

F0

12

12

E0

E0

75

72

E0

E0

F0

F0

75

72

E0

E0

12

12

85 PgUp E0 AA E0 49 E0 C9 E0 2A E0 F0 12 E0 7D E0 F0 7D E0 12

86 PgDn E0 AA E0 51 E0 D1 E0 2A E0 F0 12 E0 7A E0 F0 7A E0 12

89

? ?

E0 AA E0 4D E0 CD E0 2A E0 F0 12 E0 74 E0 F0 74 E0 12

203 Win E0 AA E0 5B E0 DB E0 2A E0 F0 12 E0 1F E0 F0 1F E0 12

204 App E0 AA E0 5D E0 DD E0 2A E0 F0 12 E0 2F E0 F0 2F E0 12

Note : The table above shows scan codes with the left Shift key. In combination with the right Shift key, scan codes are changed as listed below:

Set 1

Set 2

With left Shift With right Shift

E0 AA ___________E0 B6

E0 2A ____________E0 36

E0 F0 12 _________E0 F0 59

E0 12 ____________E0 59

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual D-5

Appendices Keyboard Scan/Character Codes

Cap

No.

43

58

60

121

122

123

Table D-3 Scan codes in Numlock mode

Cap

No.

Key top

Code set 1 Code set 2

Make Break Make Break

75 INS E0 2A E0 52 E0 D2 E0 AA E0 12 E0 70 E0 F0 70 E0 F0 12

76 DEL E0 2A E0 53 E0 D3 E0 AA E0 12 E0 71 E0 F0 71 E0 F0 12

79

? ?

E0 2A E0 4B E0 CB E0 AA E0 12 E0 6B E0 F0 6B E0 F0 12

80 Home E0 2A E0 47 E0 C7 E0 AA E0 12 E0 6C E0 F0 6C E0 F0 12

81 End E0 2A E0 4F E0 CF E0 AA E0 12 E0 69 E0 F0 69 E0 F0 12

83

84

? ?

? ?

E0

E0

2A

2A

E0

E0

48

50

E0 C8

E0 D0

E0

E0

AA

AA

E0

E0

12

12

E0

E0

75

72

E0

E0

F0

F0

75

72

E0

E0

F0

F0

12

12

85 PgUp E0 2A E0 49 E0 C9 E0 AA E0 12 E0 7D E0 F0 7D E0 F0 12

86 PgDn E0 2A E0 51 E0 D1 E0 AA E0 12 E0 7A E0 F0 7A E0 F0 12

89

? ?

E0 2A E0 4D E0 CD E0 AA E0 12 E0 74 E0 F0 74 E0 F0 12

203 Win E0 2A E0 5B E0 DB E0 AA E0 12 E0 1F E0 F0 1F E0 F0 12

204 App E0 2A E0 5D E0 DD E0 AA E0 12 E0 2F E0 F0 2F E0 F0 12

Table D-4 Scan codes with Fn key

Keytop

ENT

CTRL

LALT

ARROW

NUMERIC

Scrl

Code set 1

Make Break

E0

E0

E0

45

45

46

1C

1D

38

E0

E0

E0

9C

9D

B8

C5

C5

C5

Make

Code set 2

Break

E0

E0

E0

77

77

7E

5A E0

14 E0

11 E0

F0

F0

F0

F0 5A

F0 14

F0 11

77

77

7E

D-6 Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Keyboard Scan/Character Codes Appendices

Table D-5 Scan codes in overlay mode

Cap

No.

25

26

37

38

39

40

52

54

55

08

09

10

11

23

24

K

L

;

M

.

/

O

P

J

0

U

I

7

8

9

Keytop

(6)

(–)

(1)

(2)

(3)

(+)

(0)

(.)

(/)

(7)

(8)

(9)

(*)

(4)

(5)

Make

Code set 1

Break

E0

4D

4A

4F

50

51

4E

52

53

47

48

49

37

4B

4C

CD

CA

CF

D0

D1

CE

D2

D3

C7

C8

C9

B7

CB

CC

6C

75

7D

7C

6B

73

74

7B

69

72

7A

79

F0

F0

F0

F0

F0

F0

70

71

F0

F0

40 4A E0

F0

F0

F0

F0

F0

F0

35 E0 B5

Table D-6 No.124 key scan code

Make

Code set 2

Break

74

7B

69

72

7A

79

70

71

F0 4A

6C

75

7D

7C

6B

73

Key top

Shift Code set 1 Code set 2

Make Break Make Break

Prt Sc Common E0 2A E0 37 E0 B7 E0 AA E0 12 E0 7C E0 F0 7C E0 F0 12

Ctrl

?

Shift

?

Alt

?

E0

E0

37

37

54

E0

E0

D4

B7

B7

E0 7C

E0 7C

84

E0

E0

F0

F0

F0

B4

7C

7C

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual D-7

Appendices Keyboard Scan/Character Codes

Table D-7 No.126 key scan code

Key top

Shift Code set 1

Make

Code set 2

Make

Pause Common* E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14 F0 77

Ctrl* E0 46 E0 C6 E0 7E E0 F0 7E

*: This key generates only make codes.

D-8 Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Apx. E Key Layout

Apx. E Key Layout

Appendix E Key Layout

E.1 United States (US) Keyboard

Appendices

Figure E-1 US keyboard

E.2 Japan (JP) Keyboard

Figure E-2 JP keyboard

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual E-1

Appendices

E.3 Spanish (SP) Keyboard

Apx E Key Layout

Figure E-3 SP keyboard

E.4 Korean (KR) Keyboard

Figure E-4 KR keyboard

E-2 Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Apx.E Key Layout

E.5 Canadian-French (CF) Keyboard

Appendices

Figure E-5 CF keyboard

E.6 French (FR) Keyboard

Figure E-6 FR keyboard

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual E-3

Appendices

E.7 German (GR) Keyboard

Apx E Key Layout

Figure E-7 GR keyboard

E.8 Italian (IT) Keyboard

Figure E-8 IT keyboard

E-4 Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Apx E Key Layout

E.9 Taiwan (TC) Keyboard

Appendices

Figure E-9 TC keyboard

E.10 Portuguese (PT) Keyboard

Figure E-11 PT keyboard

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual E-5

Appendices

E.11 DU, UE, US International (USE) Keyboard

Apx E Key Layout

Figure E-12 USE keyboard

E.12 Arabic (AR) Keyboard

Figure E-13 AR keyboard

E-6 Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Apx E Key Layout

E.13 Belgian (BE) Keyboard

Appendices

Figure E-14 BE keyboard

E.14 Russian (RU) Keyboard

Figure E-15 RU keyboard

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual E-7

Appendices

E.15 Swiss/Switzerland (SL) Keyboard

Apx E Key Layout

Figure E-16 SL keyboard

E.16 Swedish (SW) Keyboard

Figure E-17 SW keyboard

E-8 Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Apx E Key Layout

E.17 Norwegian (NO) Keyboard

Appendices

Figure E-18 NO keyboard

E.18 Danish (DK) Keyboard

Figure E-19 DK keyboard

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual E-9

Appendices

E.19 Turkey (TR) Keyboard

Apx E Key Layout

Figure E-18 TR keyboard

E.20 Greek (GK) Keyboard

Figure E-19 GK keyboard

E-10 Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Apx E Key Layout

E.21 Estonia (ES) Keyboard

Appendices

Figure E-19 ES keyboard

E.22 Herbrew (HE) Keyboard

Figure E-19 HE keyboard

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual E-11

Appendices

E.23 Czech (CZ) Keyboard

Apx E Key Layout

Figure E-18 CZ keyboard

E.24 Lithuanian (LI) Keyboard

Figure E-18 LI keyboard

E-12 Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Apx E Key Layout

E.25 Hungary (HU) Keyboard

Appendices

Figure E-18 HU keyboard

E.26 Slovakia (SA) Keyboard

Figure E-18 SA keyboard

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual E-13

Appendices

E.27 Yugoslavia (YU) Keyboard

Apx E Key Layout

Figure E-19 YU keyboard

E-14 Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

Apx. F BIOS Rewrite Procedures Appendices

Appendix G

Appendix F BIOS Rewrite Procedures

This Appendix explains how to rewrite the system BIOS program when you update the system

BIOS.

Tools

To rewrite the BIOS, you need the following tool:

? BIOS/EC/KBC rewriting disk for the computer that has renewed BIOS data.

Rewriting the BIOS

1. Set the system to boot mode.

2. Turn off the power to the computer.

3. Remove the external cable and PC card.

4. Connect an external FDD and insert the BIOS/EC/KBC rewriting disk into either the external FDD.

5. Turn on the power while holding down the [

`

~

] key (on the left of the space key). (Keep holding down the key until a message appears on the screen.) The BIOS rewriting starts.

6. When the process is completed, eject the BIOS/EC/KBC rewriting disk and the system is automatically reset.

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual

F-1

Apx. G EC/KBC Rewrite Procedures Appendices

Appendix H

Appendix G EC/KBC Rewrite Procedures

This Appendix explains how to rewrite the EC/KBC system program when you update the

EC/KBC system.

Tools

To rewrite the EC/KBC, you need the following tool:

? BIOS/EC/KBC rewriting disk for the computer

Rewriting the EC/KBC

1. Set the system to boot mode.

2. Turn off the power to the computer.

3. Remove the external cable and PC Card.

4. Connect an external FDD and insert the BIOS/EC/KBC rewriting disk into either the external FDD.

5. Turn on the power while holding down the [

`

~

] key. (Keep holding down the key until a message appears on the screen.) The EC/KBC rewriting starts.

6. When the EC/KBC rewrite is completed, the system is automatically turned off.

Equium A60/Satellite A60/ Pro A60/A65 Maintenance Manual G-1

Appendices

Apx. H EC/KBC Rewrite Procedures

Note: 1. Rewrite the EC/KBS only when instructed by a diagnostic disk release1 notice.

2. Connect the AC adapter to the computer when you rewrite the EC/KBC.

3. Do not turn off the power while you are rewriting the EC/KBC. If the rewrite fails, it might be impossible to start up the computer.

4. If you fail to rewrite EC/KBC, then when you next turn on the power, a message may be displayed that the contents of the EC/KBC have been erased. In this case, insert the BIOS/EC/KBC rewriting disk, and the

EC/KBC will be rewritten.

5. Normally it takes about 30 seconds to rewrite the EC/KBC. It may take 3 minutes (maximum), depending on the conditions of the computer or ICs.

The computer is not hung up. Allow sufficient time. Never reboot or turn off the power to the computer before the rewriting is completed.

H-2

TE2100 Manual Manual

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals