3.2 Specifi cations. Ohio Medical Push-To-Set Continuous Vacuum Regulator

3.2  Specifi cations. Ohio Medical Push-To-Set Continuous Vacuum Regulator
Add to My manuals

Below you will find brief information for Vacuum Regulator Push-To-Set Continuous Vacuum Regulator. The Push-To-Set Continuous Vacuum Regulator is a lightweight, compact unit used throughout the hospital primarily for pharyngeal/tracheal suctioning (airway management). Various models provide regulated or full-line vacuum for hospital suction procedures.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

3.2  Specifi cations. Ohio Medical Push-To-Set Continuous Vacuum Regulator | Manualzz

3/Specifi cations

3.2 Specifi cations

Flow Rate:

Positive Pressure Safety

Relief Valve:

0 to 80 LPM without fi ttings at full increase setting depending on supply

Located in the vacuum supply line to prevent pressurization of the patient connection by failed injector vacuum (venturi) units, or inadvertent

Standard Models

High Models

Low Models

0 to 200 mm Hg/0 to 26 kPa 0 to 760 mm Hg/0 to 100 kPa

0 to 760 mm Hg/0 to 100 kPa 0 to 760 mm Hg/0 to 100 kPa

0 to 160 mm Hg/0 to 21 kPa 0 to 135 mm Hg/0 to 18 kPa*

* When measured with an independent measuring device.

Vacuum Relief Valve

(Low Vacuum models ONLY):

140 mm Hg ± 5 mm Hg/18.7 kPa ± 0.7 kPa

11 grams

(Less fi ttings)

Weight

Low Vacuum models:

(Less fi ttings)

12 oz/340 grams

Latex tubing, 0.25 in (6.4 mm) I.D. X

12 in (30 cm) supplied:

Disposable tubing (Available separate in some markets;

6 mm I.D. X 450 mm, 750 mm and 2M) to connect regulator and collection bottle

Disposable Suction Filter:

0 to full vacuum

Flow dependent on source and setup

0 to full vacuum

Flow dependent on source and setup

0 to full vacuum

0 to 100 Lpm @ 650 mmHg (-87 kPa)

40 o

F (4 o

C) to 120 o

F (49 o

C)

0 o

F (-18 o

C) to 150 o

F (71 o

C)

Operating and Storage Relative Humidity: 5 to 95%

8700-0006-000 Rev.3

4

advertisement

Key Features

  • Lightweight and compact
  • Provides regulated or full-line vacuum
  • Includes vacuum gauge
  • Features positive pressure safety relief valve
  • Low models have vacuum relief valve to limit maximum suction
  • Operates in regulated or non-regulated mode
  • Automatically adjusts suction level
  • Easy to use and adjust
  • Safe and reliable

Frequently Answers and Questions

What is the purpose of the Push-To-Set Continuous Vacuum Regulator?
The Push-To-Set Continuous Vacuum Regulator is used to provide suction for various medical procedures, primarily for pharyngeal/tracheal suctioning (airway management).
How do I set the suction level on the Push-To-Set Continuous Vacuum Regulator?
To set the suction level, turn the mode selector switch to "I" (On) and rotate the suction control knob until the vacuum gauge indicates the desired setting.
What is the difference between the regulated and non-regulated modes on the Push-To-Set Continuous Vacuum Regulator?
In the non-regulated (MAX) mode, the vacuum source is connected directly to the fitting port, providing full-line vacuum. In the regulated mode, the vacuum source is connected through the regulator module, which functions as an automatic valve to control the suction level.
How do I clean the Push-To-Set Continuous Vacuum Regulator?
Routine cleaning is recommended after each use. Wipe all exterior surfaces with a solution of water and mild detergent. If the regulator becomes flooded with patient fluid, all internal components (except the gauge) can be cleaned with a solution of warm water and mild detergent. Dry all components thoroughly before assembly.
How do I sterilize the Push-To-Set Continuous Vacuum Regulator?
The only acceptable method of sterilization is with gas (ethylene oxide). Follow the sterilization instructions provided in the manual carefully.

Related manuals

Download PDF

advertisement

Table of contents