6,82 MB Formato: PDF

3

Customisation

Setup

You can customise some functions of the Touch Screen by accessing this page.

Touch the icon .

The setup page will be displayed.

Alarm clock

Touch the icon to enable or disable the alarm clock.

Alarm clock activated

ALARM

CLOCK

Touch to disable

Alarm clock deactivated

ALARM

CLOCK

Touch to enable

ALARM

CLOCK

BEEP

CLOCK

Touch the icon to set the alarm clock activation time.

The following page will be displayed:

Use the arrows to set the time; every touch will allow you to increase or decrease by one unit; when you press your finger, increasing or decreasing will be faster.

Touch the icon to access the selection page of the alarm clock activation frequency.

98

Once

Always

Mon - Fri

Sat - Sun

If the sound system is configured, the icon at the bottom right corner, will let you access the configuration page of the sound system for the alarm clock; when the multi-channel sound system is required, the room must be selected.

Customisation

3

You will be able to choose the conditions of the sound system as soon as the alarm clock (source, amplifiers, volume) is activated.

Radio

Bedroom

99

The use of a multimedia source with the alarm clock is not recommended.

When the alarm clock is activated, the volume increases until it reaches the volume set previously.

If you touch the display when the alarm clock is activated, the volume of the amplifiers will be set to the current value (hence interrupting the automatic volume increase).

If there is no pressure on the display, the amplifiers will switch off after two minutes.

3

Customisation

Beep

You can enable and disable the audible signal when zones are touched.

Clock

Touch the icon to access the setup pages of the clock.

CLOCK

ALARM

CLOCK

BEEP

The following page will be displayed:

Use the arrows to set the hour, minutes and seconds; every touch will allow you to increase or decrease by one unit; when you press your finger, increasing or decreasing will be faster.

CLOCK

Touch the icon to access the setup page of the date.

If the Beep is OFF, the device will not emit an audible signal.

100

The programmed time will appear in the Home page and/or Default

Page, if applied during programming.

Use the arrows to set the day, month and year; every touch will allow you to increase or decrease by one unit; when you press your finger, increasing or decreasing will be faster.

Customisation

3

Calibration

To access the page which allows you to adjust the touch accuracy of the display, touch the icon.

CALIBRATION

Confirm by touching the icon

.

The following page will be displayed:

+

Touch the “cross” symbol on the display, in all positions (5).

The icon will appear twice in the outer areas of the display.

The programmed date will appear in the Home page and/or Default

Page, if applied during programming.

Press the cross

Confirm by touching the icons.

Calibration will start automatically.

This procedure is very delicate, although it is provided with pressure controls; if it is carried out incorrectly, the device may no longer perceive the user’s pressure areas, thus forcing it to stop. In this case, it is necessary to call a technician.

101

3

Customisation

Password

If the Touch Screen is protected with a password, the following page will appear when the display is touched.

Use the numeric keys to enter the password (default 12345)

You can cancel with

Confirm with

The display will show the page for typing in the password (see previous page):

Type in the existing password;

Confirm with .

If the password is correct, you can type in the new password

(the password will be shown on the display)

PASSWORD: 14725

Carefully memorize the new password before pressing OK because, after enabling the protection, it will be indispensable in order to use the Touch Screen.

PASSWORD: *****

Change Password

You can change the existing password at any time.

The new password must have

5 figures.

Touch the icon.

If the password is correct, the

Home page will be displayed.

Enable protection

You can enable the protection to protect the access to the

Touch Screen against unwanted actions.

By doing so, the access to the functions will be possible only for those who know the password.

PASSWORD

102

Disable

Enable

PASSWORD

PASSWORD

Version

To access the page which allows you to display the Touch Screen information, touch the

Setup page.

icon, after 10 seconds go back to the

VERSION

Customisation

3

art. H/L 4684

FIRMWARE: 12.40.5

PIC REL: 12.40.5

HARDWARE: 3.0.0

T.S. n. 0

103

Maintenance and Troubleshooting

Cleaning

Clean only with a soft cloth.

Do not use solvents or abrasive/corrosive materials.

Forgot your password?

In this case you can solve the problem by disconnecting and reconnecting the Touch Screen; after switching on the display, you can use the functions before the stopping process starts. Access the customisation menu and disable the stopping process or change the password.

No reaction to pressure

In this case you can solve the problem by disconnecting and reconnecting the Touch Screen.

Hold down and repeat the calibration procedure.

Do not use solvents or corrosive materials

104

Please note: the use of radio devices will not guarantee the correct indication of the Touch Screen status.

Software licence information

This product contains the Service_Pack_BTicino, made available, for some parts, thanks to the GNU GPL licence version 2:

http://www.gnu.org/licenses/old-licenses/gpl-2.0.html

and, in some other parts, thanks to the GNU GPL licence version 3.1:

http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html

A fully readable copy of the corresponding Service_Pack_BTicino resource code can be made available, or can be sent by BTicino SpA, at a cost not exceeding the cost of the physical distribution of the source. Please request the above by sending an e-mail in English language to the following address:

[email protected]

Please indicate the product item code and the production week.

Requests can be made within three years from the date of purchase of the product.

BTicino SpA

Via Messina, 38

20154 Milano - Italy www.bticino.it

Servizio Clienti

Timbro Installatore

Installer stamp

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project