advertisement
Replacing the Battery
1
Hold the Naída CI in one hand. Rotate the RF cable upward to avoid bumping it upon battery placement.
3
2
Align the battery cartridge connector with the processor housing side of the connector.
Slide the battery onto the processor until it clicks into place.
NOTE:
Do not force the battery cartridge onto the processor. The battery cartridges are
designed to be inserted in only one direction; applying force may damage the equipment.
24 Naída CI Sound Processor User Guide
Understanding Naída CI LEDs
The Naída CI LEDs are a programmable feature providing visual information about the Naída
CI status, battery life, program position, and error conditions.
Naída CI Sound Processor LED Indications
Color Behavior Programmable Indication
Orange Blinks at start-up
Solid
Blinks twice every three seconds
No. Battery indicator is only available with use of the rechargeable
PowerCels and AAA
PowerPak. Battery life indicators are not available with use of
Zn-Air batteries.
Yes
Yes
•
4 quick blinks indicate that the
battery is fully charged
•
2 - 3 quick blinks indicate that the
battery is sufficiently charged to
power the Naída CI
•
1quick blink indicates that the
battery is nearly depleted
•
No blinking indicates depleted
battery. Replace with charged or
new battery
The battery is almost depleted
The battery is almost depleted and cannot support stimulation
(Sleep Mode)
The Naída CI is entering Sleep Mode
Loss of lock with the implant
Red
Fades out
Blinks once per second
Blinks rapidly (more than once per second)
Solid
No
Yes
No Intellilink™ enabled and the Naída
CI is connected to the wrong implant
Green
Blinks 5 times
Flickers in response to loud inputs
Blinks at start-up, after battery status, and upon program change
No
No-if using AB myPilot this pattern is the default
Yes
No
Sound processor error condition. Fully remove and re-insert the battery to reset processor
Response to AB myPilot’s request to
‘Find Paired Devices’. The Right paired device will identify, itself with this LED pattern.
The sound processor and microphone are responding to sound
•
1 blink indicates program one
•
2 blinks indicate program two
•
3 blinks indicate program three
•
4 blinks indicate program four
•
5 blinks indicate program five
A processor that is not yet programmed Solid Green
No
Blinks 4 times
No-if using AB myPilot this pattern is the default
Response to AB myPilot’s request to ‘Find
Paired Devices’. The Left paired device will identify, itself with this LED pattern.
NOTE:
Use of some Naída CI accessories may obscure the processor LED.
Naída CI Sound Processor User Guide
25
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 Introduction
- 4 Purpose of this Guide
- 4 About the Naída CI Sound Processor
- 5 The Naída CI Sound Processor
- 6 The Naída CI Sound Processor and Accessories Overview
- 6 The Naída CI
- 7 The Universal Headpiece
- 7 AB myPilot
- 8 ComPilot
- 8 Naída CI Listening Check
- 9 Performance Technology
- 9 UltraZoom
- 9 DuoPhone
- 9 QuickSync
- 9 ZoomControl
- 9 Assembling the Naída CI
- 10 Connecting the Universal Headpiece (UHP) Color Caps
- 10 Connecting the Headpiece to the Naída CI
- 11 Removing the Headpiece from the Naída CI
- 11 Connecting the T-Mic™ 2/Earhook
- 12 Removing the T-Mic 2/Earhook
- 13 Attaching the T-Mic 2 Cover
- 13 Removing the T-Mic 2 Cover
- 14 Wearing the Naída CI
- 14 Using the Clip
- 15 Inserting the Naída CI in the Clip
- 16 Removing the Naída CI from the Clip
- 16 Using the Naída CI Sound Processor
- 16 Powering the Naída CI
- 13 Removing the Battery
- 14 Replacing the Battery
- 15 Understanding Naída CI LEDs
- 16 Understanding Internal Alarms
- 16 Using Naída CI Headpieces
- 16 The Universal Headpiece
- 16 Replacing the RF Cables
- 17 Adjusting Headpiece Magnet Strength
- 18 Removing Headpiece Color Caps
- 18 Adjusting Controls on the Naída CI
- 18 Changing Programs
- 19 Changing Volume
- 20 Changing Sensitivity
- 20 Connectivity
- 20 Using FM
- 23 Pairing to the AB myPilot
- 26 The Naída CI Listening Check and Listening Check earbuds
- 26 Listening to the Microphone(s) and Auxiliary Inputs
- 29 Using the Telephone
- 30 Telephone Tips
- 30 Telecoil
- 31 Battery Information
- 32 Assembling the PowerCel™ Charger
- 33 Inserting the PowerCels into the Charger
- 33 Removing the PowerCels from the Charger
- 34 The Zn-Air Battery Pak
- 34 Inserting Zn-Air Batteries
- 35 Inserting Zn-Air Batteries (Tamperproof Cartridge)
- 36 Charger LED (Light Emitting Diode) Indicator
- 37 Warnings
- 37 Cautions
- 37 Using Naída CI Accessories
- 38 Headpieces
- 38 Naída CI Listening Check and Listening Check Earbuds
- 39 Audio Accessories
- 39 Color Customization
- 40 Naída CI Carrying Case
- 40 Zephyr by Dry and Store
- 41 IP Rating Information
- 41 Care of the Naída CI Sound Processor and Accessories
- 41 Changing Microphone Covers
- 43 Recommended Naída CI Operating and Storage Temperatures
- 43 Approved Power Sources
- 43 Troubleshooting the Naída CI
- 45 Troubleshooting Naída CI LEDs
- 47 Troubleshooting Naída CI Internal Alarms
- 48 Guidance and Manufacturer’s Declaration
- 48 Electromagnetic Emissions
- 48 Electromagnetic Immunity
- 49 Equipment and Naída CI
- 50 Compatibility Tables
- 51 Cleaning & Maintenance
- 51 Performance Data
- 51 HiRes™ and HiRes Fidelity120™ Sound Processing
- 52 Contact Us