LIMITATION OF WARRANTY AND LIABILITY. tsi 8631-HC, 8631-HM-BAC, 8631-HM, 8631-HC-BAC

Copyright



TSI Incorporated / December 2012 / All rights reserved.

Part number 1980488 / Revision J

LIMITATION OF WARRANTY AND LIABILITY

Seller warrants the goods sold hereunder, under normal use and service as described in the operator's manual, shall be free from defects in workmanship and material for 24 months, or if less, the length of time specified in the operator's manual, from the date of shipment to the customer. This warranty period is inclusive of any statutory warranty. This limited warranty is subject to the following exclusions and exceptions: a. Hot-wire or hot-film sensors used with research anemometers, and certain other components when indicated in specifications, are warranted for 90 days from the date of shipment; b. Pumps are warranted for hour s of operation as set forth in product or operator’s manuals; c. Parts repaired or replaced as a result of repair services are warranted to be free from defects in workmanship and material, under normal use, for 90 days from the date of shipment; d. Seller does not provide any warranty on finished goods manufactured by others or on any fuses, batteries or other consumable materials. Only the original manufacturer's warranty applies; e. Unless specifically authorized in a separate writing by Seller, Seller makes no warranty with respect to, and shall have no liability in connection with, goods which are incorporated into other products or equipment, or which are modified by any person other than Seller.

The foregoing is IN LIEU OF all other warranties and is subject to the LIMITATIONS stated herein. NO OTHER

EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR PARTICULAR PURPOSE OR MERCHANTABILITY

IS MADE.

WITH RESPECT TO SELLER’S BREACH OF THE IMPLIED WARRANTY AGAINST

INFRINGEMENT, SAID WARRANTY IS LIMITED TO CLAIMS OF DIRECT INFRINGEMENT AND

EXCLUDES CLAIMS OF CONTRIBUTORY OR INDUCED INFRINGEMENTS. BUYER’S EXCLUSIVE

REMEDY SHALL BE THE RETURN OF THE PURCHASE PRICE DISCOUNTED FOR REASONABLE WEAR

AND TEAR OR AT SELLER’S OPTION REPLACEMENT OF THE GOODS WITH NON-INFRINGING

GOODS.

TO THE EXTENT PERMITTED BY LAW, THE EXCLUSIVE REMEDY OF THE USER OR BUYER, AND THE

LIMIT OF SELLER'S LIABILITY FOR ANY AND ALL LOSSES, INJURIES, OR DAMAGES CONCERNING THE

GOODS (INCLUDING CLAIMS BASED ON CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR

OTHERWISE) SHALL BE THE RETURN OF GOODS TO SELLER AND THE REFUND OF THE PURCHASE

PRICE, OR, AT THE OPTION OF SELLER, THE REPAIR OR REPLACEMENT OF THE GOODS. IN THE

CASE OF SOFTWARE, SELLER WILL REPAIR OR REPLACE DEFECTIVE SOFTWARE OR IF UNABLE TO

DO SO, WILL REFUND THE PURCHASE PRICE OF THE SOFTWARE. IN NO EVENT SHALL SELLER BE

LIABLE FOR LOST PROFITS OR ANY SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES. SELLER

SHALL NOT BE RESPONSIBLE FOR INSTALLATION, DISMANTLING OR REINSTALLATION COSTS OR

CHARGES. No Action, regardless of form, may be brought against Seller more than 12 months after a cause of action has accrued. The goods returned under warranty to Seller's factory shall be at Buyer's risk of loss, and will be returned, if at all, at Seller's risk of loss.

Buyer and all users are deemed to have accepted this LIMITATION OF WARRANTY AND LIABILITY, which contains the complete and exclusive limited warranty of Seller. This LIMITATION OF WARRANTY AND

LIABILITY may not be amended, modified or its terms waived, except by writing signed by an Officer of Seller.

SERVICE POLICY

Knowing that inoperative or defective instruments are as detrimental to TSI as they are to our customers, our service policy is designed to give prompt attention to any problems. If any malfunction is discovered, please contact your nearest sales office or representative, or call TSI's Customer Service department at (800) 874-

2811.

TRADEMARKS

TSI, TSI logo, and P

RES

S

URA

are trademarks of TSI Incorporated.

LonWorks is a registered trademark of Echelon

®

Corporation.

BACnet is a registered trademark of ASHRAE.

Microsoft is a registered trademark of Microsoft Corporation. ii

CONTENTS

HOW TO USE THIS MANUAL ..................................................................................................... IV

PART ONE ..................................................................................................................................... 1

User Basics .......................................................................................................... 1

The Instrument ..................................................................................................... 1

Operator Panel ..................................................................................................... 3

Alarms................................................................................................................... 5

Before Calling TSI ................................................................................................ 6

PART TWO ..................................................................................................................................... 7

Technical Section ................................................................................................. 7

Software Programming ......................................................................................... 7

Menu and Menu Items ........................................................................................ 12

Calibration .......................................................................................................... 32

Maintenance and Repair Parts ........................................................................... 34

Troubleshooting Section ..................................................................................... 36

APPENDIX A ................................................................................................................................ 45

Specifications ..................................................................................................... 45

APPENDIX B ................................................................................................................................ 47

Network Communications .................................................................................. 47

Model 8631-HM LonWorks

®

8631-HM LonWorks

®

Model 8631-HC LonWorks

®

8631-HC LonWorks

®

8631 BACnet

®

Model 8631-HM BACnet

®

Model 8631-HC BACnet

®

Node Object .......................................................... 47

Object .............................................................................. 48

Node Object .......................................................... 49

Object ............................................................................... 50

MS/TP Protocol Implementation Conformance Statement ........ 51

MS/TP Object Set ..................................................... 53

MS/TP Object Set ..................................................... 54

APPENDIX C ................................................................................................................................ 55

Wiring Diagrams ................................................................................................. 55

APPENDIX D ................................................................................................................................ 63

Access Codes ..................................................................................................... 63 iii