- No category
advertisement
Test Contents Test Record
Visual Inspection
The case, display screen, buttons, power cord, wall mount, and accessories have no obvious signs of damage.
The external connecting cables are not frayed and the connector pins are not loose and bent.
The external connectors are not loose or their pins are not bent.
The safety labels and data plate are clearly legible.
Power-on test
The power-on test is passed. The power indicator works correctly and the monitor starts up properly.
Performance test
SpO
2
test
Measure SpO
2
on a healthy person’s finger and a PR value is displayed. The displayed SpO
2
value is within 95% and 100%.
NIBP test
The difference is within ±3 mm when 0, 50 or 200 mmHg is set for NIBP accuracy test.
There is no leakage with NIBP, or the manual leakage test result does not exceed 6 mmHg/min.
Temp test
The displayed Temp value on the monitor is within 37 ± 0.1
℃.
Electric safety tests
Refer to Appendix A Electrical Safety Inspection.
Battery Check
The monitor can operates correctly from battery power when an AC power failure accidentally occurs.
The monitor can operate independently on a single battery.
Test conclusion:
Tested by: Test date:
Test Result
(Pass/Fail)
4-12
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 20 1 Introduction
- 20 1.1 Information of This Manual
- 20 1.2 Safety Information
- 20 1.2.1 Dangers
- 20 1.2.2 Warnings
- 20 1.2.3 Cautions
- 20 1.2.4 Notes
- 20 1.3 Equipment Symbols
- 21 2 Theory of Operation
- 21 2.1 Overview
- 21 2.2 Connectors for Peripheral Devices
- 21 2.3 Main Unit
- 21 2.4 Front Housing Assembly
- 21 2.5 Rear Housing Assembly
- 21 2.6 External Module
- 22 3 Equipment Installation
- 22 3.1 Unpacking the Equipment
- 22 3.2 Preparation for Installation
- 22 3.2.1 Preparation for Installation Site
- 22 3.2.2 Environmental Requirements
- 22 3.2.3 Electrical Requirements
- 22 3.3 Equipment Installation
- 22 3.4 Preparation for Power on
- 23 4 Testing and Maintenance
- 23 4.1 Introduction
- 23 4.1.1 Test Equipment
- 23 4.1.2 Test Report
- 23 4.1.3 Preventative Maintenance
- 23 4.1.4 Recommended Frequency
- 23 4.2 Visual Inspection
- 23 4.3 Power-on Test
- 23 4.4 Module Performance Tests
- 23 Test
- 23 4.4.2 NIBP Test
- 23 4.4.3 Temp Test
- 23 4.5 Electric safety tests
- 34 4.6 Battery Check
- 34 4.7 Maintenance Mode
- 34 4.7.1 Entering/Quitting Maintenance Mode
- 34 4.7.2 Checking Version Information
- 34 4.7.3 Restoring Factory Default Configuration
- 35 5 Troubleshooting
- 35 5.1 Overview
- 35 5.2 Parts Replacement
- 35 5.3 Troubleshooting Guide
- 35 5.3.1 Power On/Off Failure
- 35 5.3.2 Display Failures
- 35 5.3.3 Button Failures
- 35 5.3.4 Battery Failures
- 35 5.3.5 Module defective
- 35 5.3.6 Software Upgrade Problems
- 35 5.4 Error codes
- 36 6 Disassembly and Repair
- 36 6.1 Tools Required
- 36 6.2 Preparations for Disassembly
- 36 6.3 Disassembling the Main Unit
- 36 6.3.1 Disassembling the Temp Module (Optional)
- 36 6.3.2 Separating the Front and Rear Half of the Monitor
- 36 6.3.3 Removing the Parameter Connector Panel Assembly
- 36 6.3.4 Disassembling the Main Bracket Assembly
- 36 6.3.6 Disassembling Pumps and Valves (NIBP optional)
- 36 6.3.7 Disassembling AC/DC Power Board and Battery Converter Board
- 36 6.4 Disassembling the Front Housing Assembly
- 36 6.4.1 Removing the Main Board
- 36 6.4.2 Removing the Display
- 36 6.4.3 Removing the Keypad
- 36 6.5 Disassembling the Temp Module (Optional)
- 36 6.5.1 Removing the Temp Module PCBA and Temp Module Power Board PCBA
- 36 6.5.2 Disassembling the Temp On-Position Detection Board PCBA
- 37 7 Parts
- 37 7.1 Introduction
- 37 7.2 Main Unit
- 37 7.2.1 Exploded View
- 58 7.2.2 Parts List
- 58 7.3 Front Housing Assembly
- 58 7.3.1 Exploded View
- 58 7.3.2 Parts List
- 58 7.4 Main Bracket Assembly
- 58 7.4.1 Exploded View
- 58 7.4.2 Parts List
- 58 7.5 Power Management Board Assembly
- 58 7.5.1 Exploded View
- 58 7.5.2 Parts List
- 58 7.6 Parameter Connector Panel Assembly
- 58 7.6.1 Exploded View
- 58 7.6.2 Parts List
- 58 7.7 Predictive Temp Assembly
- 58 7.7.1 Exploded View
- 58 7.7.2 Parts List
- 59 8 Hardware and Software Upgrade
- 59 8.1 Hardware Upgrade
- 59 8.1.1 Upgrade Package
- 59 8.1.2 Upgrading Parameter Modules
- 59 8.1.3 Upgrading Temp
- 59 8.1.4 Enabling Parameter Functions
- 59 8.2 Software Upgrade
- 59 8.2.1 Upgrade program installation
- 59 8.2.2 Upgrading software