ADVR-0410H1M, ADVR-0820H2M, ADVR-1640H2M Digital Video Recorder User Manual

Below you will find brief information for Digital Video Recorder ADVR-0410H1M, Digital Video Recorder ADVR-0820H2M, Digital Video Recorder ADVR-1640H2M. This user manual describes how to install, configure, and operate the device, including live view, recording, playback, alarm settings, network settings, HDD management, camera settings, device management and maintenance, and other features. The manual also provides user tips and troubleshooting advice for common issues. It is recommended to read the user manual carefully before starting to use the device.

User Manual of Digital Video Recorder

Start/Stop

Auto-switch

Enable/disable the auto-switch of the screens.

Note:

The dwell time of the live view configuration must be set before using Start

Auto-switch.

Start all-day normal recording or motion detection recording for all channels. Start Recording

Quick Set Set the video output mode to Standard, Bright, Gentle or Vivid.

All-day Playback Play back the video of the selected channel.

Aux Monitor Switch to the auxiliary output mode and the operation for the main output is disabled.

Note:

If you enter Aux monitor mode and the Aux monitor is not connected, the mouse operation is disabled; you need to switch back to the Main output with the F1 button on front panel or VOIP/MON button on IR remote control and then press the Enter button.

Note:

If the corresponding camera supports intelligent function, the Reboot Intelligence option is included when right-clicking mouse on this camera.

3.2.2 Using an Auxiliary Monitor

Certain features of the Live View are also available while in an Aux monitor. These features include:

•

Single Screen: Switch to the single full screen by choosing channel number from the dropdown list.

•

Multi-screen: Adjust the screen layout by choosing from the dropdown list.

•

Previous Screen: Switch to the previous screen.

•

Next Screen: Switch to the next screen.

•

Quick Set: Set the video output mode to Standard, Bright, Gentle or Vivid.

•

Menu Output Mode: Select the menu output mode to HDMI/VGA, Main CVBS or Auto.

•

Main Monitor: Switch to the Main Output mode and the operation for the auxiliary output is disabled.

Note:

In the live view mode of the main output monitor, the menu operation is not available while Aux output mode is enabled.

3.2.3 Main/Aux Output Switching

When the HDMI/VGA output is configured as the main output, you can perform the following operation to switch to CVBS output as the main output.

Steps:

1. Use the mouse wheel to double-click on the HDMI/VGA output screen, and the following message box pops up:

Figure 3.2 Switch Main and Aux Output

2. Use the mouse wheel to double-click on the screen again to switch to the Aux output, or click Cancel to

Key Features

PAL/NTSC adaptive video inputs
H.264 video compression
Encoding at up to WD1 resolution
Dual-stream support per channel
Independent configuration for each channel
Motion detection alarm
Multiple PTZ protocols supported
Remote control and monitoring
Backup to USB, SATA, or eSATA
Embedded Web server

Questions & Answers

2024-11-08

F F I

Where are recordings saved?

Recordings are saved on the SATA hard disk(s). The ADVR-0410H1M supports one disk, while the ADVR-0820H2M/ADVR-1640H2M models support up to two.

What is the maximum storage capacity per hard disk?

Each hard disk can hold up to 4TB of data.

How can I access recorded files?

Recorded files can be viewed in the Playback menu. Searching is possible by channel, time, event, tag, and system log.

Frequently Answers and Questions

What are the supported models for this user manual?

This manual is applicable to the following models: ADVR-0410H1M, ADVR-0820H2M, ADVR-1640H2M.

What are the key features of this digital video recorder?

This device supports PAL/NTSC adaptive video inputs, H.264 video compression, encoding at up to WD1 resolution, dual-stream per channel, independent configuration for each channel, motion detection alarm, multiple PTZ protocols, remote control and monitoring, backup to USB, SATA, or eSATA, and embedded Web server.

How do I start up and shut down the device?

To start up the device, ensure the power supply is plugged in and press the POWER button on the rear panel. To shut down the device, enter the Shutdown menu, click the Shutdown button, and then turn off the power switch on the rear panel.

Related manuals

Download PDF

ADVR-0410H1M, ADVR-0820H2M, ADVR-1640H2M Digital Video Recorder User Manual