ADVR-0410H1M, ADVR-0820H2M, ADVR-1640H2M Digital Video Recorder User Manual

ADVR-0410H1M, ADVR-0820H2M, ADVR-1640H2M Digital Video Recorder User Manual
Add to My manuals

Below you will find brief information for Digital Video Recorder ADVR-0410H1M, Digital Video Recorder ADVR-0820H2M, Digital Video Recorder ADVR-1640H2M. This user manual describes how to install, configure, and operate the device, including live view, recording, playback, alarm settings, network settings, HDD management, camera settings, device management and maintenance, and other features. The manual also provides user tips and troubleshooting advice for common issues. It is recommended to read the user manual carefully before starting to use the device.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

ADVR-0410H1M, ADVR-0820H2M, ADVR-1640H2M Digital Video Recorder User Manual | Manualzz

User Manual of Digital Video Recorder alias must be started with letters of the lower-case English alphabet.

5.

Click the Apply button to save and exit the interface.

9.2.3 Configuring NTP Server

Purpose:

A Network Time Protocol (NTP) Server can be configured on your device to ensure the accuracy of system date/time.

Steps:

1.

Enter the Network Settings interface.

Menu > Configuration > Network

2.

Select the NTP tab to enter the NTP Settings interface.

Figure 9.12 NTP Settings Interface

3.

Check the Enable NTP checkbox to enable this feature.

4.

Configure the following NTP settings:

Interval: Time interval between the two synchronizing actions with NTP server. The unit is minute.

NTP Server: IP address of NTP server.

NTP Port: Port of NTP server.

5.

Click the Apply button to save and exit the interface.

Note:

The time synchronization interval can be set from 1 to 10080min, and the default value is 60min. If the device is connected to a public network, you should use a NTP server that has a time synchronization function, such as the server at the National Time Center (IP Address: 210.72.145.44). If the device is setup in a more customized network, NTP software can be used to establish a NTP server used for time synchronization.

9.2.4 Configuring SNMP

Purpose:

You can use SNMP protocol to get device status and parameters related information.

Steps:

1.

Enter the Network Settings interface.

Menu > Configuration > Network

2.

Select the SNMP tab to enter the SNMP Settings interface.

116

advertisement

Key Features

  • PAL/NTSC adaptive video inputs
  • H.264 video compression
  • Encoding at up to WD1 resolution
  • Dual-stream support per channel
  • Independent configuration for each channel
  • Motion detection alarm
  • Multiple PTZ protocols supported
  • Remote control and monitoring
  • Backup to USB, SATA, or eSATA
  • Embedded Web server

Questions & Answers

2024-11-08

F F I

Where are recordings saved?
Recordings are saved on the SATA hard disk(s). The ADVR-0410H1M supports one disk, while the ADVR-0820H2M/ADVR-1640H2M models support up to two.
What is the maximum storage capacity per hard disk?
Each hard disk can hold up to 4TB of data.
How can I access recorded files?
Recorded files can be viewed in the Playback menu. Searching is possible by channel, time, event, tag, and system log.

Frequently Answers and Questions

What are the supported models for this user manual?
This manual is applicable to the following models: ADVR-0410H1M, ADVR-0820H2M, ADVR-1640H2M.
What are the key features of this digital video recorder?
This device supports PAL/NTSC adaptive video inputs, H.264 video compression, encoding at up to WD1 resolution, dual-stream per channel, independent configuration for each channel, motion detection alarm, multiple PTZ protocols, remote control and monitoring, backup to USB, SATA, or eSATA, and embedded Web server.
How do I start up and shut down the device?
To start up the device, ensure the power supply is plugged in and press the POWER button on the rear panel. To shut down the device, enter the Shutdown menu, click the Shutdown button, and then turn off the power switch on the rear panel.

Related manuals

Download PDF

advertisement

Table of contents