ADVR-0410H1M, ADVR-0820H2M, ADVR-1640H2M Digital Video Recorder User Manual

Below you will find brief information for Digital Video Recorder ADVR-0410H1M, Digital Video Recorder ADVR-0820H2M, Digital Video Recorder ADVR-1640H2M. This user manual describes how to install, configure, and operate the device, including live view, recording, playback, alarm settings, network settings, HDD management, camera settings, device management and maintenance, and other features. The manual also provides user tips and troubleshooting advice for common issues. It is recommended to read the user manual carefully before starting to use the device.

User Manual of Digital Video Recorder

Figure 10.11 Local HDD Settings Interface

Select the Group number for the current HDD.

Note:

The default group No. for each HDD is 1.

Click the OK button to confirm the settings.

Figure 10.12 Confirm HDD Group Settings

In the pop-up Attention box, click the Yes button to finish the settings.

10.3.2 Setting HDD Property

Purpose:

The HDD property can be set to redundancy, read-only or read/write (R/W). Before setting the HDD property, please set the storage mode to Group (refer to step1-4 of Chapter 10.3.1 Setting HDD Groups).

A HDD can be set to read-only to prevent important recorded files from being overwritten when the HDD becomes full in overwrite recording mode.

When the HDD property is set to redundancy, the video can be recorded both onto the redundancy HDD and the

R/W HDD simultaneously so as to ensure high security and reliability of video data.

Steps:

Enter the HDD Information interface.

Menu > HDD > General

Select HDD from the list and click the icon to enter the Local HDD Settings interface.

136

User Manual of Digital Video Recorder

Figure 10.13 Set HDD Property

Set the HDD property to R/W, Read-only or Redundancy.

Click the OK button to save the settings and exit the interface.

In the HDD Information menu, the HDD property will be displayed in the list.

Note:

At least 2 hard disks must be installed on your device when you want to set a HDD to Redundancy, and there is one HDD with R/W property.

137

Key Features

PAL/NTSC adaptive video inputs
H.264 video compression
Encoding at up to WD1 resolution
Dual-stream support per channel
Independent configuration for each channel
Motion detection alarm
Multiple PTZ protocols supported
Remote control and monitoring
Backup to USB, SATA, or eSATA
Embedded Web server

Questions & Answers

2024-11-08

F F I

Where are recordings saved?

Recordings are saved on the SATA hard disk(s). The ADVR-0410H1M supports one disk, while the ADVR-0820H2M/ADVR-1640H2M models support up to two.

What is the maximum storage capacity per hard disk?

Each hard disk can hold up to 4TB of data.

How can I access recorded files?

Recorded files can be viewed in the Playback menu. Searching is possible by channel, time, event, tag, and system log.

Frequently Answers and Questions

What are the supported models for this user manual?

This manual is applicable to the following models: ADVR-0410H1M, ADVR-0820H2M, ADVR-1640H2M.

What are the key features of this digital video recorder?

This device supports PAL/NTSC adaptive video inputs, H.264 video compression, encoding at up to WD1 resolution, dual-stream per channel, independent configuration for each channel, motion detection alarm, multiple PTZ protocols, remote control and monitoring, backup to USB, SATA, or eSATA, and embedded Web server.

How do I start up and shut down the device?

To start up the device, ensure the power supply is plugged in and press the POWER button on the rear panel. To shut down the device, enter the Shutdown menu, click the Shutdown button, and then turn off the power switch on the rear panel.

Related manuals

Download PDF

ADVR-0410H1M, ADVR-0820H2M, ADVR-1640H2M Digital Video Recorder User Manual

Assistant Bot