advertisement
System expansions/Alterations BASIC1 - User manual
9.5 Install field bus module (Hilscher)
With help of the Leukhardt adapter card a fieldbus module can be plugged directly as module onto the fieldbus interface of the CPU board.
Conditions
•
The MSC IPC has to be disconnected from the supply net (disconnect power plug).
•
The right cover is opened.
The fieldbus interface is placed above the DRAM memory module (see fig., marking)
Fig. 9-4: Fieldbus-interface on CPU board
Fig. 9-5: Leukhardt fieldbus adapter card and fieldbus interface, Hilscher
The pins of the Leukhardt fieldbus adapter card and the pins of the fieldbus interface are interconnected (see fig., marking).
Press the cards cautiously together to avoid damaging the pins!
Page 66 of 100 Rev. 2.00 of 28.5.2002
BASIC1 - User manual System expansions/Alterations
The interconnected cards (adapter card/fieldbus card) are plugged into the fieldbus slot with the lower side of the adapter card.
Fig. 9-6: Fieldbus interface on adapter card and CPU board
For fieldbus modules an address range of 16 K beginning at address DC000h is set as default value.
IRQ 11 is available as interrupt.
Rev. 2.00 of 28.5.2002 Page 67 of 100
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 6 Basic notes on handling and operation
- 8 Characteristics
- 8 Features
- 9 Nomenclature
- 10 Basic equipment
- 10 Options
- 11 Safety hints
- 11 Symbol and reference explanation
- 12 Safety standards and determination
- 12 Dangers
- 12 Electric hazards
- 13 Mechanical hazards
- 14 Operating and service personnel
- 14 Consider hints
- 14 Obligation
- 14 Qualification
- 15 Transport, storage, disposal
- 15 Installation, start-up, maintenance
- 16 Cleaning
- 16 Suitable fire extinguishing agents
- 17 Technical data
- 17 General
- 19 Mechanical measurements
- 20 Installation
- 20 Unpacking MSC IPC and testing scope of delivery
- 20 Unpacking
- 20 Scope of delivery
- 21 Mounting Conditions
- 21 Environmental conditions
- 21 Ventilation
- 22 Mounting situation
- 24 Fixing
- 24 Accessories
- 24 Mounting
- 24 Connection of the peripherals
- 24 Safety
- 25 External connections and interfaces
- 28 Connecting supply distribution
- 29 Putting into Operation
- 29 Functional elements
- 30 Switch-on of the current supply
- 30 Conditions
- 30 To boot the computer
- 30 Software installation
- 30 Installation of the operating system
- 30 Installation of the periphery drivers
- 35 Data back-up
- 36 BIOS Setup
- 36 Hints for BIOS-Setup
- 36 Calling BIOS-Setup
- 37 Setup Main Menue
- 39 Standard CMOS Setup
- 41 BIOS Features Setup
- 45 Chipset Features Setup
- 48 Power Management Setup
- 51 PNP/PCI Configuration
- 54 Integrated Peripherals
- 60 MicroDesign Features Setup
- 62 Software Interfaces
- 62 Address Overview System Memory
- 63 Interrupts (IRQ)
- 64 System expansions/Alterations
- 64 Safety
- 64 Open housing
- 65 Installation of a slot card
- 66 Install Memory Module
- 67 Install field bus module (Hilscher)
- 69 Fault diagnosis
- 69 General references
- 69 General errors, cause, remedy
- 71 Maintenance/Repair of the MSC IPC
- 71 Safety
- 71 Cleaning
- 71 General Hints
- 71 Cleaning of fan filter mat
- 72 Replace device fan
- 73 Replace CPU fan
- 74 Replace system battery
- 76 Spare parts
- 76 Questions to the manufacturer, user questions
- 76 Contact
- 76 Data for calling
- 76 Current Drivers and Tools