Legacy Platinum SCR Single Phase Charger

Add to my manuals
30 Pages

advertisement

Legacy Platinum SCR Single Phase Charger | Manualzz

4.2 Wall Mounting (Optional)

WARNING: THE CHARGER IS NOT TO BE POSITIONED ON, OR MOUNTED OVER, ANY

FLAMMABLE SUBSTANCE.

WARNING: THE WALL AND THE FASTENERS USED MUST BE CAPABLE OF SUPPORTING THE

DESIGN LOAD SHOWN IN FIGURE 4.2-1. USE APPROPRIATE FASTENERS FOR THE WALL

CONSTRUCTION. THE USE OF FOUR MACHINE BOLTS IS REQUIRED TO SECURE THE LOAD.

NOTIFY YOUR DEALER’S QUALIFIED SERVICE TECHNICIAN IF YOU HAVE ANY QUESTIONS OR

PROBLEMS OCCUR.

CAUTION: ALLOW 4” (102mm) MINIMUM CLEARANCE BETWEEN THE CHARGER AND ANY

WALL, 6” (152mm) FROM OTHER EQUIPMENT TO ALLOW FOR PROPER VENTILATION.

CAUTION: TO ENSURE THE STRUCTURAL INTEGRITY OF THE WALL MOUNTING BRACKETS:

USE 8, 3/8’ DIAMETER BOLTS (NOT PROVIDED) TO ATTACH BRACKETS TO A WALL/STRUCTURE.

AVIOD USING LAG BOLTS.

To install the wall mounting brackets, this procedure must be followed in sequence. The brackets are to be used as shown in Figure 4.2-2.

1. Locate the holes for the fasteners according to the dimensions in the illustrations. Note: Where applicable, connect fasteners directly to studs in the wall.

2. Use a level to ensure proper mounting.

3. Use each bracket as a template and mark where the mounting holes should be located. When locating the brackets, bracket flanges should face towards the inside. Do not use the slots for mounting the bracket to the wall.

CAUTION: THE CHARGER MUST BE SUPPORTED UNTIL IT IS SECURED TO THE BRACKETS.

4. Secure charger to brackets using the hardware provided with the wall mounting kit. (Refer to the appropriate illustration for placement instructions.)

5. When the charger / wall brackets are mounted on the wall, there will be a clear airflow space at the rear of the charger. This space should not be reduced or obstructed in any way.

WARNING: IF CHARGER IS DROPPED OR SEVERELY BUMPED DURING HANDLING, DO NOT

OPERATE CHARGER. POSSIBLE DAMAGE OR UNSAFE OPERATING CONDITIONS MAY OCCUR.

CONTACT YOUR DEALER’S QUALIFIED SERVICE TECHNICIAN.

www.douglasbattery.com 9 of 30 User’s Manual

Model Number

6-450B

6-550B

6-680B

12-380B

12-550B

12-680B

12-850B

18-600B

18-800B

24-600B

Enclosure Size

Single Phase

Single Phase

Single Phase

Single Phase

Single Phase

Single Phase

Single Phase

Single Phase

Single Phase

Single Phase

Charger Weight lbs. (Kg.)

180 (82)

190 (86)

193 (88)

200 (91)

223 (101)

225 (102)

260 (118)

248 (113)

290 (132)

290 (132)

Design Load lbs. (Kg.)

900 (410)

950 (430)

965 (440)

1000 (455)

1115 (505)

1125 (510)

1300 (590)

1240 (565)

1450 (660)

1450 (660)

WARNING: DO NOT STACK CHARGERS WHEN USING WALL MOUNTING

BRACKETS. BRACKETS ARE DESIGNED TO SUPPORT ONE CHARGER ONLY.

Single-Phase Cabinet Dimensions: 19.0” W x 27.0” H x 17.5” D

Figure 4.2-1: Wall Anchor Design Load Table

Figure 4.2-1 shows the weight that the set of mounting bolts and their anchoring structure must withstand for the various charger types. The “Design Load” shows the “Charger Weight” times a safety factor of five (5). Be certain that both the mounting structure and the bolts will, at a minimum, support the “Design Load”. Drywall or plaster will not be strong enough on its own, without proper structural reinforcement.

Wall Fasteners

(Not supplied with wall mounting kit)

8 Required

Figure 4.2-2: Single-Phase Charger Wall Mounting Bracket Installation

www.douglasbattery.com 10 of 30 User’s Manual

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals