advertisement
To install the panels, do the same steps in reverse.
11.6 Removing and cleaning the door glasses - main oven
The door glass in your product can be different in type and shape from the example you see in the image. The number of glasses can also be different.
1. Push the door trim at one side to remove it.
1
2
A
ENGLISH 23
11.7 Replacing the lamp
Put a cloth on the bottom of the interior of the appliance. It prevents damage to the lamp glass cover and the cavity.
WARNING!
Danger of electrocution!
Disconnect the fuse before you replace the lamp.
The lamp and the lamp glass cover can be hot.
1. Deactivate the appliance.
2. Remove the fuses from the fuse box or deactivate the circuit breaker.
The back lamp
The lamp glass cover is at the back of the cavity.
1. Turn the lamp glass cover counterclockwise to remove it.
2. Clean the glass cover.
3. Replace the oven lamp with a suitable 300 °C heat-resistant oven lamp.
Use the same oven lamp type.
4. Install the glass cover.
2. Pull up the trim.
3. Remove the glass panels.
To replace the glass panels, do the same steps in reverse. Before you lower the trim, attach the A trim part to the door. Refer to the image.
12. TROUBLESHOOTING
WARNING!
Refer to Safety chapters.
24 www.aeg.com
12.1 What to do if...
Problem
You cannot activate the appliance.
Possible cause
The appliance is not connected to an electrical supply or it is connected incorrectly.
Remedy
Check if the appliance is correctly connected to the electrical supply.
You cannot activate the appliance.
Residual heat indicator does not come on.
The fuse is released.
The zone is not hot because it operated only for a short time.
Make sure that the fuse is the cause of the malfunction.
If the fuse releases again and again, contact a qualified electrician.
If the zone operated sufficiently long to be hot, speak to an Authorised Service
Centre.
Activate the inner ring first.
You cannot activate the outer ring.
The oven does not heat up.
The oven is deactivated.
The oven does not heat up.
The clock is not set.
The oven does not heat up.
The lamp does not operate.
The necessary settings are not set.
The lamp is defective.
The display shows "12.00".
There was a power cut.
Steam and condensation settle on the food and in the cavity of the oven.
You left the dish in the oven for too long.
Activate the oven.
Set the clock.
Make sure that the settings are correct.
Replace the lamp.
Reset the clock.
Do not leave the dishes in the oven for longer than 15 -
20 minutes after the cooking process ends.
12.2 Service data
If you cannot find a solution to the problem yourself, contact your dealer or an Authorised Service Centre.
The necessary data for the service centre is on the rating plate. The rating plate is on the front frame of the appliance cavity. Do not remove the rating plate from the appliance cavity.
We recommend that you write the data here:
Model (MOD.) .........................................
Product number (PNC)
Serial number (S.N.)
.........................................
.........................................
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 1. SAFETY INFORMATION
- 4 2. SAFETY INSTRUCTIONS
- 7 3. PRODUCT DESCRIPTION
- 8 4. BEFORE FIRST USE
- 9 5. HOB - DAILY USE
- 9 6. HOB - HINTS AND TIPS
- 10 7. HOB - CARE AND CLEANING
- 11 8. OVEN - DAILY USE
- 13 9. OVEN - CLOCK FUNCTIONS
- 15 10. OVEN - HINTS AND TIPS
- 21 11. OVEN - CARE AND CLEANING
- 23 12. TROUBLESHOOTING
- 25 13. INSTALLATION
- 26 14. ENERGY EFFICIENCY