advertisement
2. Configure the following:
• Channel: Select the channel you wish to configure.
• Enable: Select Enable or Disable to activate or deactivate motion recording.
• Area: Click the Setup button to configure the area of the screen that detects motion.
Click and drag the mouse cursor to configure motion detection areas. Motion detection is enabled in red areas and disabled in transparent areas. Right-click to exit.
• Sensitivity: Select motion sensitivity. The greater the number, the greater the sensitivity.
• Alarm Out: Select the checkbox to enable the system to trigger an alarm device
(not included).
• Latch Time: Enter the duration alarm devices (not included) will continue to trigger after the event ends.
• Show Message: Select the checkbox if you want the system to display a system message when an alarm triggers.
• Buzzer: Select the duration the system will "beep" when motion is detected. Or select OFF to disable the "beep" during motion events.
• Send Email: Select the checkbox if you want the system to send email notifications if an alarm triggers. Email notifications must be configured.
• Record Channel: Select the channel you wish the DVR to record during motion recording.
• Full Screen: Select the Full Screen check box so that the system goes into full screen mode when motion or an alarm trigger is detected.
• Post Recording: Enter the post recording duration (the time the system continues to record after a motion event occurs).
3. Click Apply to save your settings.
15.5.2
Configuring Alarm Settings
The Alarm tab allows you to configure how the system behaves when an external alarm device (not included) is triggered.
Note
External alarm devices (such as glass break detectors; not included) are required to configure settings in the Alarm tab. Some models do not support alarm devices. Check the specifications for your DVR to determine if it supports alarm devices.
#LX400015; r. 1.0/13705/13705; en-US
57
To configure the Alarm tab:
1. From the Alarm menu, click the Alarm tab.
2. Configure the following:
• Alarm In: Select the channel you wish to configure.
• Alarm Type: Select the alarm type of the device. Choose from N/O (normally open),
N/C (normally closed).
• Alarm Out: Select the checkbox to enable the system’s alarm block to trigger a connected external alarm.
• Latch Time: Enter the duration the alarm continues to trigger after the event ends.
• Show Message: Select the checkbox if you want the system to display a system message when an alarm triggers.
• Buzzer: Select the checkbox to enable the system to "beep" if an alarm triggers.
• Send Email: Select the checkbox if you want the system to send email notifications if an alarm triggers.
• Post Recording: Select the duration the system continues to record as an event after the alarm trigger ends. For example, if you select 30s (30 seconds), the system continues to record for 30 seconds after the alarm trigger ends.
• Full Screen: Select the check box so that the system goes into full screen mode when motion or an alarm trigger is detected.
3. Click Apply to save your settings.
#LX400015; r. 1.0/13705/13705; en-US
58
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 11 Important Safeguards
- 11 General Precautions
- 11 Installation
- 13 Service
- 14 Features
- 15 Getting Started (LH040 Series)
- 16 Front Panel (LH040 Series)
- 17 Rear Panel (LH040 Series)
- 18 Basic Setup (LH040 Series)
- 18 Step 1: Connect the DVR Docking Stand (OPTIONAL)
- 18 Step 2: Connect the Octopus Cable
- 19 Step 3: Connect the Mouse
- 19 Step 4: Connect the Ethernet cable
- 20 Step 5: Connect the Monitor
- 20 Step 6: Connect the Power Adapter and Power on the DVR
- 20 Step 7: Upgrade Firmware to Latest Version (if Available)
- 21 Step 8: Verify Camera Image
- 21 Step 9: Set the Time
- 21 Default System Password & Port Numbers
- 22 6.10.1 Lorex Stratus Connectivity
- 22 Quick Access to System Information
- 22 Connecting Cameras
- 22 6.12.1 Installing Cameras
- 23 6.12.2 Connecting BNC Cameras to your DVR
- 24 6.12.3 Connecting and Removing BNC Cables
- 25 Mouse Control
- 26 Remote Control
- 28 Using the On-Screen Display
- 28 Using the Menu Bar
- 29 Using the Virtual Keyboard and Mini-Keyboard
- 30 Using the Zoom Mode
- 30 Using Picture in Picture (PIP) Mode
- 32 Setting the Date and Time
- 32 Configuring Daylight Savings Time (DST)
- 33 Using a NTP Server to set your System Time
- 35 Recording
- 35 Recording Audio
- 36 Playback
- 36 Playing Back Recorded Video
- 37 12.1.1 Using Playback Controls
- 38 12.1.2 Finding Events in the Playback Bar
- 39 12.1.3 Controlling the Time Range of the Playback Bar
- 39 12.1.4 Using Zoom in Playback Mode
- 40 Quick Playback
- 42 Backup
- 42 Backing Up Video
- 43 Using Video Clip Backup
- 44 Viewing Backed Up Video
- 45 Managing Passwords
- 45 Changing Passwords
- 46 Adding Users
- 49 Using the Main Menu
- 50 Display
- 50 15.1.1 Configuring Custom Channel Names
- 50 15.1.2 Changing the Position of the Channel Name
- 50 15.1.3 Adjusting Camera Color Settings
- 51 15.1.4 Enabling Covert Recording
- 51 15.1.5 Configuring the Time and Recording Time Display
- 51 15.1.6 Configuring Sequence Time
- 52 15.1.7 Changing the Video-out Resolution
- 52 Screen
- 53 15.1.9 Adjusting Menu Transparency
- 53 15.1.10 Adjusting the Video Margin
- 53 15.1.11 Adding Privacy Zones
- 54 15.1.12 Creating a Custom Split-screen Display
- 56 Record
- 56 15.2.1 Configuring Pre-recording Settings
- 56 Alarm)
- 57 15.2.3 Enabling Audio Recording
- 58 Frame Rate
- 60 Search
- 60 15.3.1 Using the Event Search
- 61 15.3.2 Using the Log Search
- 62 Network
- 62 15.4.1 Configuring Network Type: DHCP & Static IP
- 62 15.4.2 Enabling Auto Port Forwarding
- 62 15.4.3 Changing the DVR’s Client and HTTP Port
- 63 15.4.4 Adjusting Remote Connectivity Streaming Rates
- 64 15.4.5 Setting up Email Notification
- 65 15.4.6 Configuring DDNS settings
- 66 Alarm
- 66 15.5.1 Configuring Motion Detection
- 67 15.5.2 Configuring Alarm Settings
- 69 Device
- 69 15.6.1 Formatting the Hard Drive
- 69 15.6.2 Configuring Overwrite
- 70 15.6.3 Formatting USB Flash Drives
- 71 System
- 71 15.7.1 Changing Date Format
- 71 15.7.2 Changing Time Format
- 71 15.7.3 Changing the System Language
- 71 15.7.4 Changing Video Output - NTSC & PAL
- 71 15.7.5 Configuring Menu Time Out and Auto Logout
- 71 15.7.6 Adding Users & Changing the Admin Password
- 72 15.7.7 Viewing System Information
- 72 15.7.8 Setting the Remote Control ID
- 73 Advanced
- 73 15.8.1 Configuring Firmware Upgrades
- 73 Drive
- 74 15.8.3 Restoring to Factory Default Settings
- 75 15.8.4 Restarting or Shutting Down the DVR
- 76 15.8.5 Configuring System Warnings
- 77 Drive
- 79 Connecting to Your DVR Over the Internet on PC or Mac
- 79 System Requirements
- 79 Step 1 of 3: Connect your DVR to Your Router
- 80 Step 2 of 3: Obtain the DVR’s Device ID
- 81 Step 3 of 3: Connect to the DVR Over the Internet
- 84 Using the PC/Mac Client Software
- 85 Changing Viewing Modes
- 85 Taking Screen Shots
- 85 Recording Video
- 86 Showing / Hiding Channels
- 86 Viewing the Bit Rate
- 87 Video
- 87 Changing the Format of Recorded Video (PC Only)
- 88 Configuring PTZ Settings
- 89 Video Playback
- 91 17.9.1 Video Playback Controls
- 92 Configuring Display Settings
- 92 Configuring Privacy Zone Settings
- 93 Configuring Recording Parameters
- 93 Configuring the Recording Schedule
- 94 Configuring System Recording Quality
- 95 Configuring Basic Network Settings
- 95 Configuring the System Substream
- 96 Configuring Email Notification Settings
- 97 Configuring DDNS Settings
- 98 Configuring Motion Detection Settings
- 99 Configuring your System to "Beep" During Motion
- 99 Configuring Alarm Notifications
- 100 Configuring Hard Drive Recording Mode
- 100 Configuring PTZ Parameters
- 101 Configuring the System Time and Date
- 102 Changing the System’s Menu Time Out
- 102 Configuring System User Accounts
- 103 Viewing System Information
- 103 Configuring Firmware Upgrades
- 103 Manually Upgrading System Firmware
- 104 Restoring Default Settings
- 105 Configuring Event Settings
- 106 Mobile Apps: Accessing your DVR Using a Mobile Device
- 106 Supported Apps and Platforms
- 106 iPhone
- 106 18.2.1 Connecting to Your System Using Lorex Eco Stratus
- 109 18.2.2 Lorex Eco Stratus Interface
- 109 18.2.3 Taking Screenshots
- 110 18.2.4 Taking Manual Recordings
- 110 18.2.5 Using PTZ Controls
- 111 18.2.6 Using Remote Playback Mode on iPhone
- 112 18.2.7 Viewing Screenshots
- 113 18.2.8 Viewing Manual Recordings
- 114 18.2.9 Using Device Manager to Manage DVR’s
- 115 18.3.1 Prerequisites
- 115 18.3.2 Connecting to your DVR
- 118 18.3.3 Live View Interface
- 118 18.3.4 Taking Screenshots
- 118 18.3.5 Taking Manual Recordings
- 119 18.3.6 Using PTZ Controls
- 119 18.3.7 Using Remote Playback Mode
- 121 18.3.8 Viewing Screenshots
- 122 18.3.9 Viewing Manual Recordings
- 123 18.3.10 Using Device Manager to Manage DVRs
- 124 18.3.11 Managing Favorites
- 125 Android
- 125 18.4.1 Connecting to Your System Using Lorex Eco Stratus
- 127 18.4.2 Lorex Eco Stratus Interface
- 128 18.4.3 Taking Screenshots
- 128 18.4.4 Taking Manual Recordings
- 128 18.4.5 Using PTZ Controls
- 129 18.4.6 Using Remote Playback Mode on Android
- 131 18.4.7 Viewing Screenshots
- 133 18.4.8 Viewing Manual Recordings
- 134 18.4.9 Using Device Manager to Manage DVR’s
- 136 Lorex Player 11: Playing Backed up Video on PC
- 136 Running Lorex Player
- 137 Lorex Player 11 Interface Overview
- 137 19.2.1 About the Advanced Config Menu
- 138 Converting Backed Up Video to AVI Files
- 140 Lorex Player for Mac: Viewing Backed up Video on Mac
- 140 Opening Individual Video Files
- 140 Loading Multiple Video Files
- 141 Lorex Player for Mac Interface
- 142 Connecting a PTZ Camera
- 142 Configuring PTZ Settings
- 143 Using the PTZ Menu (Local DVR)
- 144 PTZ Presets and PTZ Cruise
- 144 21.3.1 PTZ Preset Controls
- 144 21.3.2 Setting PTZ Presets
- 145 21.3.3 Selecting PTZ Presets
- 145 21.3.4 Deleting PTZ Presets
- 145 21.3.5 Starting / Stopping PTZ Cruise
- 146 Connecting Additional External Monitors
- 146 Connecting the DVR to TV RCA Ports
- 146 Monitor
- 148 Recording Audio
- 150 Replacing the Hard Drive
- 150 Removing the Hard Drive
- 152 Installing the Hard Drive
- 155 Formatting the Hard Drive
- 157 DDNS Setup (Advanced)
- 157 Accessing your DVR within a local network (LAN)
- 157 Network
- 158 25.1.2 Step 2 of 3: Obtain the DVR’s Local IP Address
- 158 25.1.3 Step 3 of 3: Connect to the DVR’s Local IP Address
- 160 DDNS Setup—Access your DVR Remotely over the Internet
- 160 25.2.1 Step 1 of 4: Port Forwarding
- 161 25.2.2 Step 2 of 4: Create a DDNS Account
- 165 25.2.3 Step 3 of 4: Enable DDNS on the DVR
- 165 25.2.4 Step 4 of 4: Connect to the DVR’s DDNS Address
- 168 Troubleshooting
- 171 LH040 Series System Specifications
- 174 Notices
- 174 FCC/IC Notice
- 174 Modification