advertisement
Mounting and Dismounting 46/122
5 Mounting and Dismounting
5.1 Safety Messages on Personal Injury
Obey to the following safety messages on personal injury, when mounting, dismounting or replacing the netBRICK NB 100 device.
5.1.1 Use in Hazardous Locations only in Scope of the UL Standards
The Use in Hazardous Locations with Potentially Explosive Atmosphere is only allowed in Scope of the UL Standards!
Important!
Outside the scope of the UL standards you are allowed to use the netBRICK NB 100 device in non-hazardous locations only!
When using the device in hazardous locations with potentially explosive atmosphere according to UL (UL-Report/File E326833) you must observe the following safety messages.
Explosion Hazard!
Do not connect or disconnect the netBRICK NB 100 device unless power has been removed or the area is known to be non-hazardous.
Substitution of components may impair suitability for NEC500 Class I,
Division 2, Groups A, B, C, and D.
Do not use the diagnostic interface DIAG (USB connector) of the net-
BRICK NB 100 device in hazardous locations. Use the diagnostic interface DIAG only, if power has been removed or the area is known to be non-hazardous.
Use only a power supply specified according to the UL standard.
5.1.2 Danger of unsafe System Operation
Danger of unsafe System Operation
To prevent harm of persons, do not remove this device under runtime conditions before you can not guarantee further a safe and secure operation of the plant. netBRICK NB 100 | Gateway Devices
DOC091111UM12EN | Revision 12 | English | 2014-03 | Released | Public © Hilscher, 2009-2014
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 6 About the User Manual
- 6 Obligation to read and understand the Manual
- 7 List of Revisions
- 8 Conventions in this Manual
- 9 Reference to Hardware, Software, Driver and Firmware
- 10 Contents of the Product DVD
- 10 Directory Structure of the DVD
- 11 Device Description Files
- 12 Documentation for netBRICK
- 15 Legal Notes
- 15 Copyright
- 15 Important Notes
- 16 Exclusion of Liability
- 16 Warranty
- 17 Export Regulations
- 17 Registered Trademarks
- 18 General Note
- 18 Intended Use
- 18 Personnel Qualification
- 18 References Safety
- 19 Safety Instructions to avoid Personal Injury
- 19 Use in Hazardous Locations only in Scope of the UL Standards
- 19 Danger of unsafe System Operation
- 20 Safety Instructions to avoid Property Damage
- 20 Device Destruction by exceeding allowed Supply Voltage
- 20 Electrostatically sensitive Devices
- 20 Danger of unsafe System Operation
- 21 Labeling of Safety Messages
- 22 Device Description
- 23 Device Names
- 24 Protocol Conversions
- 24 Protocol Conversion - Ethernet to Fieldbus
- 26 Protocol Conversion - Serial Protocols to Fieldbus
- 27 System Requirements
- 27 Configuration Requirements
- 28 Licenses
- 29 Dimensioned Drawing
- 29 Drilling Template
- 30 Device Label
- 31 Positions of LEDs and Control Elements
- 31 Elements of the netBRICK NB 100-RE-xx Device
- 32 Elements of the netBRICK NB 100-RS-xx Device
- 33 Connections
- 33 X1 Power Supply PWR
- 34 X2 Front Connection
- 36 X3 Fieldbus Connection
- 39 Diagnostic Interface
- 41 Schematic Diagram - Galvanic Isolation
- 41 Galvanic Isolation NB 100-RE-DP Device
- 43 Galvanic Isolation NB 100-RE-DN/CO Device
- 44 Galvanic Isolation NB 100-RS-DP Device
- 45 Galvanic Isolation NB 100-RS-DN/CO Device
- 46 Safety Messages on Personal Injury
- 46 Use in Hazardous Locations only in Scope of the UL Standards
- 46 Danger of unsafe System Operation
- 47 Property Damage Messages
- 47 Device Destruction by exceeding allowed Supply Voltage
- 47 Electrostatically sensitive Devices
- 47 Danger of unsafe System Operation
- 48 Mounting
- 48 Use in Hazardous Locations only in Scope of the UL Standards
- 49 Dismounting
- 49 Use in Hazardous Locations only in Scope of the UL Standards
- 51 Commissioning
- 51 Maintainance
- 52 Boot up Behavior
- 52 Boot up Behavior on valid Firmware
- 52 Boot up Behavior on invalid Firmware
- 62 Failure in 10 MBit/s Half Duplex Mode and Workaround
- 63 LED SYS
- 63 LED APL
- 64 LEDs Real Time Ethernet Systems
- 64 LED EtherCAT Master
- 65 LED EtherCAT Slave
- 67 LED EtherNet/IP Scanner (Master)
- 68 LED EtherNet/IP Adapter (Slave)
- 69 LED Open Modbus/TCP
- 70 LED POWERLINK Controlle Node/Slave
- 72 LED PROFINET IO RT Controller
- 73 LED PROFINET IO-RT-Device
- 74 LED sercos Master
- 76 LED sercos Slave
- 77 LEDs Fieldbus Systems
- 77 LED PROFIBUS DP Master
- 77 LED PROFIBUS DP Slave
- 78 LED CANopen Master
- 79 LED CANopen Slave
- 80 LED DeviceNet Master
- 80 LED DeviceNet Slave
- 81 LEDs Serial
- 81 LED Modbus RTU
- 81 LED ASCII
- 82 LED 3964R
- 83 Technical Data netBRICK NB 100 Gateway
- 87 Technical Data Real-Time Ethernet Protocols
- 87 EtherCAT Master
- 87 EtherCAT Slave
- 88 EtherNet/IP Scanner (Master)
- 89 EtherNet/IP Adapter (Slave)
- 90 Open Modbus/TCP
- 90 POWERLINK Controlled Node (Slave)
- 91 PROFINET IO-RT-Controller
- 92 PROFINET IO-RT-Device
- 93 sercos Master
- 94 sercos Slave
- 95 Technical Data Fieldbus Protocols
- 95 CANopen Master
- 96 CANopen Slave
- 97 DeviceNet Master
- 98 DeviceNet Slave
- 99 PROFIBUS DP Master
- 100 PROFIBUS DP Slave
- 101 Technical Data serial Protocols
- 101 ASCII
- 102 Modbus RTU Master/Slave
- 103 3964R
- 104 PROFIBUS
- 106 CANopen
- 107 DeviceNet
- 109 Ethernet
- 115 Decommissioning
- 115 Disposal of Waste Electronic Equipment
- 118 List of Figures
- 119 List of Tables
- 122 Contacts