Toshiba RemotEye

Add to my manuals
135 Pages

advertisement

Toshiba RemotEye | Manualzz

Hardware Specifications

RemotEye III Feature Summary

CPU

Memory

Network

Serial Communication

Serial Connection

Jumper

DIP Switch

LED

Reset Button

RTC

16-Bits AC1106 Fast Ethernet RISC Processor

2MB(1Mbit x16) TFBGA Flash ROM

2MB (1Mbit x16) SDRAM

Support 10/100 Mbits

RJ45 LAN Connector

Two UART Channels, one RJ-45, one Gold finger.

Console - RJ45 Connecter (FULL Function /RS-232 Level)

UPS - Gold finger (TXD, RXD/RS-232 Level)

Two bits for upgrade mode configure.

Two bits for operating mode configure.

Power x1 (Green)

Status x1 (Yellow)

LAN 10 Link/Activity x 1 (Yellow)

LAN 100 Link/Activity x 1 (Green)

One Push Button

Real time clock

128

System Specification

Description

Power Input

Power Consumption

Temperature Operating

Temperature Non-operating

Humidity Operating

Humidity Non-operating

Board dimension

Weight

Regulation

Specification

+8V ~ +15VDC

3.0 Watts Maximum

+8V DC 1.56 Watts

+15V DC 1.7 Watts

0

∘C ~ +60∘C

-10∘ C ~ +70∘ C

10 ~ 80 %

5 ~ 95 %

65.8x 60 x 15.2 mm (LxWxH)

45 gm

CE,FCC class B

Firmware Specifications

Network Protocols

SNMP

UPS Protocol

SNMP over UDP/IP ,HTTP over TCP/IP

ARP, RARP , DHCP, DNS, BOOTP, SMTP, SNTP, TFTP,

SSL, SSH, PPP, ICMP

RFC 1628, JEMA MIB, TOSHIBA MIB

TOSHIBA UPS protocol

129

LED Key

Front 

Figure 29: RemotEye III/Internal Top View

4 3 2 1

Figure 30: Front View – LED location

(1) Status LED (Yellow)

J2

(2) Power LED (Green)

(3) LAN 10 Link/Activity LED (Yellow)

Table 3. LED define list

130

Jumper Setting

2

1

4

3

J4 Jumper

Pin1/2 Pin3/4

0

0

1

1

1

0

1

0

1: Jumper short ; 0 : Jumper open

Function

Reserved

Clear Password

Reserved

Reserved

Table 4. J4 Jumper Setting Table

※ Example: Setup Serial Upgrade Z-modem Mode (S1 DIP Switch must Setup: S1-1 on, S1-2 off)

Pin1/2: Jumper open.

Pin3/4: Jumper short.

2

1

4

3

131

DIP Switch Setting

1 2

ON

S1 DIP Switch

S1-1(PIN1/4) S1-2(PIN2/3) Function

ON

OFF

ON

OFF

ON

ON

OFF

OFF

Manufacturing Diagnostic Mode

Debug Mode

Serial Upgrade Mode

Operational Mode (Default)

Table 5. S1 DIP Switch Setting Table

LAN connector (J2)

Pin

6

7

4

5

8

1

2

3

Signals

TX+ / TDP

TX- / TDN

RX+ / RDP

NC

NC

RX- / RXN

NC

NC

Function

OUTPUT +

OUTPUT -

INPUT +

NO CONNECT

NO CONNECT

INPUT -

NO CONNECT

NO CONNECT

Table 6. RJ45 LAN connector pin descriptions

132

Console connector (J3)

Pin

5

6

7

8

1

2

3

4

Signals

RTSPC#

DTRPC#

TXDPC#

COM

DCDPC#

RXDPC#

DSRPC#

CTSPC#

Function

Request To Send – RS232 level

Data Terminal Ready – RS232 level

Serial Data Out (to PC) – RS232 level

GND

Data Carrier Detector – RS232 level

Serial Data In (from PC) – RS232 level

Data Set Ready – RS232 level

Clear To Send– RS232 level

Table 7. RJ45 Console connector pin descriptions

Gold Finger GF1

PIN Num.

8

9

10

5

6

7

1

2

3

4

Signals

GND

UPSVCC

TXDUPS(to UPS) – RS-232 level

RXDUPS(from UPS) – RS-232 level

NC

NC

NC

D+

GND

D-

Note

8~15Vdc

Detect+

Detect-

Table 8. Gold finger GF1 pin descriptions

133

INDUSTRIAL DIVISION

13131 West Little York Rd., Houston, TX 77041

Tel: 713/466-0277 Fax 713/466-8773

US 877/867-8773 Canada 800/872-2192 Mexico 01/800/527-1204 www.toshiba.com/ind

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents