Техническая документация для ViVOpay Kiosk II (406 Кб)

Техническая документация для ViVOpay Kiosk II (406 Кб)

ViVOpay Kiosk II Installation

This section provides information on how to install the ViVOpay Kiosk II on a kiosk.

Part List

Verify that you have the following hardware for the installation of the ViVOpay Kiosk II:

 ViVOpay Kiosk II Controller

 ViVOpay Kiosk II Antenna (either square or angle bezel)

 Antenna LED power and data cable

 ViVOpay Kiosk II to ECR/POS cable (customer supplied). This USB or serial cable varies based on the host to be used.

 Drill Template for the antenna (630-1046-00)

Copyright © 2010-2014, International Technologies & Systems Corp. All rights reserved.

Page 7 of 18

Mounting the ViVOpay Kiosk II External Antenna

Use the following instructions to mount the antenna on the exterior of the kiosk:

Note: Verify the orientation of the ViVOpay Kiosk II Antenna before marking and drilling the holes. The two larger holes should be located towards the top of the mounting location to ensure that the ViVOpay Kiosk II Antenna is oriented correctly with the LEDs at the top.

1. Using the Drill Template for the antenna (630-1046-00), locate and mark the four

4.4mm (0.173 inch) mounting holes.

2. Using the Drill Template, locate and mark the two 14.0 mm (0.551 inches) across holes (used for connecting the antenna power and the LED power and data cable to the ViVOpay Kiosk II).

3. Drill the four 4.4 mm (0.173) mounting holes using a number 17 drill bit.

4. Drill the two 14.0 mm (0.551 inch) holes using a 35/64 drill bit.

5. Remove the nuts from the four mounting screws.

6. Route the end of the cable (220-2457-00) with the RJ45 connector through the left

14.0 mm (0.551 inch) hole in to the kiosk. Make sure that the front of the antenna will be properly oriented (not upside down) on the kiosk before inserting the four screws into the mounting holes.

Copyright © 2010-2014, International Technologies & Systems Corp. All rights reserved.

Page 8 of 18

7. Align the four screws with the mounting holes and attach the ViVOpay Kiosk II to the outside surface. Make sure that the cable is not pinched or binding.

8. Use the four nuts to secure the ViVOpay Kiosk II to the outside surface of the kiosk.

Make sure to tighten the nuts securely so that the ViVOpay Kiosk II does not move on the outside surface of the kiosk.

If you are installing the Angle Bezel Antenna, tighten the nuts to 5-7 in/lbs. for a good weather seal.

9. Attach the end of the cable with the SMB connector through the right 14.0 mm (0.551 inch) hold and attach it to the socket on the back of the ViVOpay Kiosk II antenna.

The SMB connector pushes on the socket of the antenna.

Copyright © 2010-2014, International Technologies & Systems Corp. All rights reserved.

Page 9 of 18

10. Attach the RJ45 connector coming from the ViVOpay Kiosk II Antenna to the RJ45 receptacle on the 220-2457-00 cable.

Flush- Mounting the Square Bezel Antenna

The RF field of the antenna is sensitive to the proximity of metal. If you are flushmounting the antenna in a metal surface or bezel, you have three options:

 Mount with the RF emitting surface of the antenna at least 1 cm forward of any metal.

 Mount with the RF emitting surface of the antenna at least 1 cm behind any metal. This will reduce the effective range of the antenna.

 Mount flush with the metal but allow a minimum of 1 cm spacing between the antenna and the metal.

In all cases, test the antenna mounting before engaging in a full scale installation.

Mounting the ViVOpay Kiosk II Controller

Note: The ViVOpay Kiosk II Controller must be mounted within 1 meter of the antenna. If the antenna is mounted on a surface that opens (such as a door), make sure the controller and antenna are close enough that there is no tension on the cable when the enclosure is open.

If it is acceptable, the installer can drill four holes for mounting the controller if screw heads can appear on the outside of the kiosk. In this case, it would be advisable to use security screws to prevent tampering with the screws.

If drilling additional holes on the outside of the kiosk surface is not acceptable, the installer can use double-sided tape to mount the controller to any clean surface.

Mounting the ViVOpay Kiosk II Controller Using Screws

1. Position the ViVOpay Kiosk II controller on the interior of the kiosk making sure that there is sufficient room for the antenna mounting surface to be fully opened.

Copyright © 2010-2014, International Technologies & Systems Corp. All rights reserved.

Page 10 of 18

2. Locate the four 4.4 mm (0.173 inch) mounting holes by holding the ViVOpay Kiosk II

Controller in position and mark the holes. The following diagram shows the spacing on the holes to be drilled for mounting the ViVOpay Kiosk II Controller.

3. Drill the four 4.4 mm (0.173 inch) mounting holes using a number 17 drill bit.

4. Use four screws and nuts to mount the ViVOpay Kiosk II Controller to the kiosk surface. (Mounting screws are not provided and must be supplied by the installer.)

5. Tighten the nuts to hold the ViVOpay Kiosk II Controller in position so that it does not move.

Mounting the ViVOpay Kiosk II Controller Using Mounting Tape

1. Position the ViVOpay Kiosk II Controller on the interior of the kiosk making sure that there is sufficient room for the antenna mounting surface to be fully opened.

2. Attach double-sided tape to the mounting surface.

3. Position the ViVOpay Kiosk II Controller over the mounting tape and gently apply pressure to hold the controller in position.

Attaching the Cables from the Antenna to the Controller

1. Attach the SMB end of the cable (220-2457-00) from the antenna to the ViVOpay

Kiosk II Controller.

Copyright © 2010-2014, International Technologies & Systems Corp. All rights reserved.

Page 11 of 18

2. Attach the other end of the cable (220-2457-00) from the antenna to the ViVOpay

Kiosk II Controller.

Note: Verify that the polarizing plug on the end of the data cable is facing towards the top of the

ViVOpay Kiosk II Controller (away from the mounting plate) before inserting the cable. If the cable is installed incorrectly (upside-down), it will apply the wrong polarity to the LEDs and damage them.

Connecting to Power

The Kiosk II can be powered through the serial communications port or the two-socket power connector. If you are using USB data communications, you must power the Kiosk

II through the two-socket power connector.

Connect +7.5 to 36 VDC to the white two-socket Molex connector (mating connector

Molex P/N 0039012020 with 5556-series crimps) or to pins 1 and 2 of the RS232 connector (see next section).

Copyright © 2010-2014, International Technologies & Systems Corp. All rights reserved.

Page 12 of 18

Connecting to the Data Port

The Kiosk II has two data connections options: USB through the USB connector and

RS232 through the 14-pin Molex connector.

The USB port uses a standard USB connector and pin outs. The RS232 port has the following pin outs.

Pin Description

1 Power ground

3 Power ground

Pin

2

4

Description

+7.5v to 36VDC

+7.5v to 36VDC

6 Reserved

7 Reserved

9 Signal ground

11 RS232 Tx

8 Reserved

10

12

Signal ground

RS232 Rx

14 Reserved

To build your own RS232 cable, use Molex female connector part number 0511101451 with 50394-series crimps (see www.molex.com

for more information). Pin 1 is indicated by a triangle (diagram is socket-side view of the female connector). If you are powering the Kiosk II from this connector, wire the two power pins (pins 2 and 4) together and the two power ground pins together (pins 1 and 3).

Copyright © 2010-2014, International Technologies & Systems Corp. All rights reserved.

Page 13 of 18

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project