advertisement
Adjusting settings via the operating menu
The extended menu “ Advanced Menu ”
Setting transmission frequencies for the frequency bank
“U” – “Tune”
When you have selected one of the system banks and then select the “ Tune ” menu, the bodypack transmitter automatically switches to channel 1 of the frequency bank “ U ”. In this case, “ U.1
” briefly appears on the display panel.
Upon delivery, the channels of the frequency bank
“ U ” are not assigned a transmission frequency.
When you are in the “ Tune ” menu item, the
RF signal is deactivated.
Via the “ Tune ” menu item, you can set a transmission frequency to be stored in the current channel or you can select a different channel in the frequency bank “ U ” and assign this channel a transmission frequency.
It is vital to observe the notes on frequency
Setting a transmission frequency for the current channel
왘
Press the rocker button until the “ Tune ” menu item appears.
왘
Press the SET button.
The frequency selection appears.
Advanced Menu
Tune
543.200 MHz
Call up “Tune”
SET
Tune
543 .200 MHz
SET
Tune
544.
200 MHz
Select the MHz value and confirm
Select the kHz value; store the setting
SET
“Stored”
왘
Set the desired frequency.
왘
Press the SET button.
Your settings are stored.
You are back to the operating menu.
Selecting a channel and assigning this channel a frequency
왘
Press the rocker button until the “ Tune ” menu item appears.
왘
Keep the SET button pressed until the channel selection appears.
23
Adjusting settings via the operating menu
Advanced Menu
Tune
543.200 MHz
Call up “Tune”
(special function)
SET
Tune
543.200 MHz
Select the channel; store the setting
SET
Tune
543 .200 MHz
Set the frequency
SET
“Stored”
왘
Set the desired channel.
왘
Press the SET button.
The frequency selection appears.
왘
Set the desired frequency.
왘
Press the SET button.
Your settings are stored.
You are back to the operating menu.
Setting the mode for the MUTE switch – “Mute Mode”
Advanced Menu
Mute Mode
AF On/Off
Call up
“Mute Mode”
SET
Mode
“
“
“
AF On/Off
RF On/Off
Disabled ”
”
”
Mute Mode
AF On/Off
Mute Mode
RF On/Off
Select the desired setting
Store the setting
SET
“Stored”
Function
When the switch is in the MUTE position, no audio signal is transmitted.
When the switch is in the MUTE position, the RF signal is deactivated.
The muting function is deactivated.
For information on how to use the MUTE switch, refer to
Emulating guitar cables – “Cable Emulation”
Advanced Menu
Cable Emulation
Medium
Call up “Cable
Emulation”
SET
Cable Emulation
Medium
Select the desired setting
Cable Emulation
High
Store the setting
SET
“Stored”
Via the “ Cable Emulation ” menu item, you can emulate
4 different guitar cable capacities.
Activating/deactivating the pilot tone transmission –
“Pilot Tone”
Advanced Menu
SET
Active
Call up
“Pilot Tone”
Pilot Tone
Active
Select the desired setting
Pilot Tone
Inactive
Store the setting
SET
“Stored”
24
Adjusting settings via the operating menu
The bodypack transmitter adds an inaudible signal, known as the pilot tone, to the transmitted signal. The receiver detects and evaluates the pilot tone.
The pilot tone supports the receiver’s squelch function
(Squelch) and protects against interference due to
RF signals from other devices.
Devices of the ew 100 G1 series (generation 1) do not support the pilot tone function. Therefore, please observe the following when combining a bodypack transmitter or receiver of the ew 100 G3 series (generation 3) with devices from an earlier evolution wireless generation:
Transmitter Receiver Make sure to ...
w G3/ w G2 w G3/ w G2 ... activate the pilot tone function on both bodypack transmitter and receiver.
w G3 w G1 w G1 w G3
... deactivate the pilot tone function on the ew 100 G3 bodypack transmitter.
... deactivate the pilot tone function on the ew 100 G3 receiver.
Adjusting the contrast of the display panel –
“LCD Contrast“
You can adjust the contrast of the display panel in 16 steps.
Resetting the settings made in the operating menu –
“Reset”
Advanced Menu
Reset
SET
Reset
Yes
Call up “Reset”
“Stored”
Select the desired setting; apply the setting
SET
When resetting the settings made in the operating menu, only the selected settings for the pilot tone and for the frequency bank “ U ” remain unchanged. For an overview of the factory-preset default settings, refer to the supplied frequency information sheet.
Displaying the software revision – “Software Revision”
You can display the current software revision of the bodypack transmitter.
25
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 Important safety instructions
- 4 The SK 100 G3 bodypack transmitter
- 4 The frequency bank system
- 5 Areas of application
- 6 Delivery includes
- 7 Product overview
- 7 Overview of the SK 100 G3 bodypack transmitter
- 8 Overview of the displays
- 9 Putting the bodypack transmitter into operation
- 9 Inserting the batteries/accupack
- 9 Charging the accupack
- 9 Connecting the microphone cable/instrument cable
- 10 Attaching and positioning the microphones
- 11 Attaching the bodypack transmitter to clothing
- 12 Using the bodypack transmitter
- 12 Switching the bodypack transmitter on/off
- 13 Deactivating the lock mode temporarily
- 14 the RF signal
- 16 Selecting a standard display
- 17 Using the operating menu
- 17 The buttons
- 18 Overview of the operating menu
- 19 Working with the operating menu
- 21 Adjusting settings via the operating menu
- 21 The main menu “Menu
- 24 The extended menu “Advanced Menu
- 27 with a receiver
- 27 with the receiver – individual operation
- 27 with receivers – multi-channel operation
- 28 Cleaning the bodypack transmitter
- 29 Recommendations and tips
- 30 If a problem occurs
- 31 Accessories and spare parts
- 32 Specifications
- 33 Connector assignment
- 34 of the microphones
- 35 Manufacturer Declarations
- 37 Index