3. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO18-33007
3.1 CUTTER MODULE (B-4208-QM)
3. INSTALLATION PROCEDURE FOR OPTIONAL
EQUIPMENT
WARNING!
Make sure to unplug the power cord before installing any optional equipment.
3.1 CUTTER MODULE (B-4208-QM)
NOTE: This module cannot be used together with the B-4908-H-QM strip module. Remove the strip module if it has been attached to the printer.
Description
Cutter Unit
Cutter
Cutter Harnes
Cutter Support
Q’ty/Unit
1
1
1
1
Description
Cutter Attaching Screw
Screw (FL-4x6)
Screw (SM-4x6C)
Cleaner
Q’ty/Unit
2
2
1
1
1) Open the right side cover and the top cover. (See Fig. 2-1.)
2) Remove the left side cover. (See Fig. 2-1.)
3) Remove the front plate. (See Fig. 2-5.)
4) Remove the screw (SM-4x8B) and two connectors to detach the operation panel.
5) Attach the cutter support to the main frame with the two screws (FL-4x6).
Screw (FL-4x6)
Screw (SM-4x8B)
Connector
Main Frame
Operation Panel
Connector
Cutter Support
Screw (FL-4x6)
Fig. 3-1
6) Install the cutter unit with the attached four screws (cutter attaching screw, SM-4x6C and
FL-4x6).
3-1
3. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO18-33007
3.1 CUTTER MODULE (B-4208-QM)
7) Connect the cutter harness to CN1 on the cutter I/F PC board through the opening of the cutter unit.
When installing the cutter, make sure that the cutter guide is not in contact with the platen. If it is, print failure or noise may be caused.
Fig. 3-2
8) Connect the cutter harness to CN4 on the I/O PC board.
I/O PC Board
CN4
Cutter Harness
9) Mount the cutter cover with the two screws.
Screw
Cutter Unit
Fig. 3-3
Cutter Cover
3-2
Cutter Attaching Screw
Fig. 3-4
3. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO18-33007
3.1 CUTTER MODULE (B-4208-QM)
10) Mount the operation panel and the left side cover on the printer.
11) Close the top and right covers.
12) After reassembly is complete, perform a test print to confirm that the cutter works properly. If the print start position becomes misalign when media is fed in the reverse direction, fine adjust the back feed value using the Back Feed Fine Adjustment procedure in diag. mode.
NOTE:
Retain the parts that are removed during installation of the cutter unit. They will be required when the printer is modified to a standard type.
R e m o v e d P a r t s
F r o n t p l a t e
Q ' t y / U n i t
1
R e m o v e d P a r t s
S c r e w ( F L 4 x 6 )
Q ' t y / U n i t
3
■
Adjusting the Cutter Guide Plates
After replacing the cutter unit the following adjustment procedure should be employed to prevent paper jams.
1.
Attach the cutter guide plate A with two SM-4 x 6C screw so that the fixed cutter is positioned 0.1
mm to 0.4 mm above the bottom of the cutter guide plate A.
2.
Attach the cutter guide plate B with two FL-4 x 8 screws so that there is a clearance of 0.5 mm between the cutter guide plate A and cutter guide plate B using a clearance gauge.
Screw
(SM-4 x 6)
Cutter Guide Plate B
Fixed Cutter
Screw
(FL-4 x 8)
Cutter Guide Plate A
Fig. 3-5
3-3
3. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO18-33007
3.2 STRIP MODULE (B-4908-H-QM)
3.2 STRIP MODULE (B-4908-H-QM)
NOTE: This module cannot be used together with the B-4208-QM cutter module. Remove the cutter module if it has been attached to the printer.
D e s c r i p t i o n
S t r i p U n i t
S t r i p H a r n e s s
Q ' t y / U n i t
1
1
1) Open the right side cover and the top cover. (See Fig. 2-1)
2) Remove the left side cover (See Fig. 2-1)
3) Remove the front plate (See Fig. 2-5)
4) Remove the operation panel (See Fig. 3-5)
5) Connect the strip harness to the CN2 on the PWM PC board through the opening of the strip base.
6) Install the strip unit to the printer with the four FL-4 x 6 screws removed in STEP 3.
7) Connect the strip harness to the CN4 on the I/O PC board.
8) Connect the strip sensor harness to the CN15 on the I/O PC board.
I/O PC Board
Screw (FL-4x6)
Screw (FL-4x6)
PWM PC Board
Strip Harness
CN15
CN4
CN2
Strip Harness
Strip Unit
Strip Sensor Harness
Strip Base
Opening
Screw (FL-4x6)
Fig. 3-6
9) Mount the operation panel and the left side cover on the printer.
10) Close the top and right covers.
11) Refer to Section 6.4 of the Maintenance Manual to load the label and make a test print to check forproper strip issue. If not, refer to Section 6.3.2 of the Maintenance Manual to adjust the strip position.
3-4
3. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO18-33007
3.3 PCMCIA PC BOARD (B-8700-PC-QM)
3.3 PCMCIA PC BOARD (B-8700-PC-QM)
Description
Installation Manual
PCMCIA PC Board
SM-3x8 Screw
Ferrite Core
PCB Holder Plate
Q’ty/Unit
1
1
4
1
1
1) Turn the power off.
2) Open the right side and top covers (See Fig. 2-1).
3) Remove the six screws (FL-4x6, B-4x6 and B-3x8) to detach the left side cover. (See Fig. 2-1).
4) Remove the two FL-3x5 screws to detach the blind plate.
Blind Plate
FL-3x5 Screw
Rear Cover
5) Detach the three harnesses from CN2, CN5 and CN7 on the CPU PC board.
CN2
CN5
CN7
Harness
Fig. 3-7
CPU PC Board
Fig. 3-8
3-5
3. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO18-33007
3.3 PCMCIA PC BOARD (B-8700-PC-QM)
6) Fix the PCB holder plate to the CPU PC board with the SM-3x8 screw so that the PCB holder plate aligns with the PCB support plate.
CPU PC Board
PCB Holder Plate
PCB Support
Plate
SM-3x8 Screw
Fig. 3-9
7) Connect the CN51 on the PCMCIA PC board to the CN9 on the CPU PC board.
8) Fix the PCMCIA PC board with the three SM-3x8 screws on the CPU PC board and the PCB holder plate.
PCB Holder Plate
CPU PC Board
SM-3x8 Screw
PCMCIA PC Board
SM-3x8 Screw
Fig. 3-10
9) Return the three harnesses to CN2, CN5, CN7 on the CPU PC board.
10) Attach the ferrite core to any cable attached to a PCMCIA PC board (Example LAN card) that may be inserted into the card slot. Place the ferrite core as close to the PCMCIA card as possible.
11) Reassemble the left side cover in the reverse order removal.
3-6
