7. ON LINE OPERATION
EO18-33007
7.1 RESET OPERATION
7. ON LINE OPERATION
7.1 RESET OPERATION
This operation restores the printer to the initial status.
• Sample operation
Power On
O N L I N E
Press the [PAUSE] key.
P A U S E
Press and hold the [RESTART] key for at least 3 seconds.
< 1 > R E S E T
Press the [PAUSE] key.
O N L I N E
The printer is in stand-by or printing.
The printer enters the pause state.
A reset menu is displayed.
The printer is restored to the initial state.
NOTES:
1. If the [RESTART] key is released within 3 seconds in the pause state, the printer will resume printing without displaying the reset menu.
2. If the [RESTART] key is released within 3 seconds in the error state, the printer will remain in error. However, in case of a communication error or command error, the printer will restore to the initial status.
7-1
7. ON LINE OPERATION
EO18-33007
(Revision Date: Apr. 25, 2002)
7.2 Dump Mode
7.2 Dump Mode
Receive buffer data of RS-232C I/F, Centronics I/F, Network I/F, and BASIC Interpreter are dumped in this mode. Communication data and Network connection can be checked.
Power On
O N L I N E
The printer is in stand-by or printing.
Press the [PAUSE] key.
P A U S E
The printer enters the pause state.
Press and hold the [RESTART] key for at least 3 seconds.
A reset menu is displayed.
< 1 > R E S E T
Press the [RESTART] key twice.
< 3 > D U M P M O D E
A dump mode menu is displayed.
Press the [PAUSE] key.
B U
Select receive buffer with the [FEED] key or [RESTART] key.
N O
F
W
F E R R S -
Press the [PAUSE] key.
P R I N T I N G . . .
2 3 2 C
RS-232C: RS-232C receive buffer
NETWORK: Network I/F receive buffer
CENTRO:
BASIC 1:
Centronics I/F receive buffer
BASIC Interpreter
BASIC 2:
(I/F Interpreter buffer)
BASIC Interpreter
(Interpreter Printer buffer)
Receive buffer data is printed. After that, the display restores the dump mode menu.
7-2
7. ON LINE OPERATION
EO18-33007
(Revision Date: Apr. 25, 2002)
7.2 Dump Mode
Receive buffer data is printed on the following condition.
■
Sample Print
[Print condition]
• Print width:
• Sensor:
4.2"
No sensor
• Print speed: 4"/sec.
• Print method (Thermal transfer/Thermal direct) which is in used is applied.
• 24-byte data is printed on one line.
53 43 24 3D 43 48 0A 00 1B 3A 2B 24 30 31 32 30 5E FF 01 0B 3C 2C 12 40
23 31 32 33 34 2C 31 2C 34 2C 41 0A 00 1B 20 45 89 00 30 30 30 31 2C 34
45 67 3B 2C 0A 00 0D 30 7B 3C FF 24 30 31 32 30 2E 9F 31 34 31 33 22 45
20 4F 3D 2C 21 22 23 24 2C 30 41 42 43 44 5B 21 26 73 06 13 4C 3F 32 33
67 32 4C 4A 50 12 33 34 35 36 2C 43 44 45 2C 0A 00 45 4C A4 BB 45 34 23
67 90 90 2C 34 35 36 37 2D 63 57 52 3B 79 97 56 5B 66 45 30 31 32 33 34
70 12 2C 34 53 76 5F D4 CC A3 26 78 35 70 7B 65 34 35 36 2C 40 0A 00 40
Feed direction
Receive buffer size
RS-232C:
Centronics I/F:
Network I/F:
BASIC 1:
BASIC 2:
10K bytes (427 lines)
10K bytes (427 lines)
8K bytes (342 lines)
4K bytes (171 lines)
4K bytes (171 lines)
NOTE:
When an error occurs on printing, an error message is displayed and the printing stops.
Pressing [PAUSE] key releases the error and restores the display to “<3> DUMP MODE”, however an auto reissue is not performed after that.
7-3
