DFL-800 Quick Installation Guide
4.2 Using the Setup Wizard
The DFL-800 provides Web based configuration. You can configure your DFL-800 through Internet Explorer 6 and later or Firefox 1.0 and later browser in MS Windows, Macintosh or UNIX based platforms.
Activate your browser, and ensure your built-in Pop-Up Blocker has been disabled, so that the Pop-Up Blocker will not block the Startup
Wizard while you initiate the NetDefend Firewall for the first time.
Additionally, in order to reduce the impact of Pop-Up Blocker, a userfriendly mechanism has beem implemented in NetDefend Firewalls. A
"Startup Wizard" button is shown on the toolbar since firmware v2.20.
This button is available on the WebGUI while the appliance is initiated with Configuration Version 1. Once you complete configuration and save/activate the setting, the Startup Wizard button will be removed automatically from the toolbar while you login WebGUI next time.
Now, let's start on WebGUI login, type the IP address of the DFL-800, e.g. https://192.168.1.1, in the Location (for Netscape) or Address (for
IE) field and press "Enter".
Open your Web browser and type
https://192.168.1.1 /
into the URL address box.
Then press the Enter or
Return key.
Note:
DFL-800 allows either HTTP or a secure HTTPS connection from any management host. However, for security reason, by default only a secure HTTPS connection is allowed.
Log on to the DFL-800 web interface.
To start using the DFL-800 web interface you need to log on using the default username and password.
Type the default
Username/Password
Username: admin
Pasword: admin and click Login
06
DFL-800 Quick Installation Guide
Step1 - Welcome to the DFL-800 setup wizard!
This wizard will guide you through the setup of your DFL-800
Click
Next
Step2 - Set up firewall administrator password
First
Enter the username that you want to use for the admin account.
Enter the password that you want to use for the admin account.
Click
Next
07
Step 3 - Set up time and date
Click Set time and date button for setting device
Select the appropriate date
Enter the appropriate time
Click
OK
Click
Next
08
DFL-800 Quick Installation Guide
Step 4 - Set up timezone
Select the appropriate timezone.
Enter the appropriate dayligt saving time settings.
Step 5 - Select WAN interface
Select the WAN interface that you want to use.
Click
Next
Click
Next
09
DFL-800 Quick Installation Guide
Step 6 - Configure WAN interface
Select the appropriate configuration for the
WAN interface,
Click
Next
and continue to step 7.1 further down.
Note:
If you are unsure of which setting to select, please contact your
Internet Service Provider.
Step 7.1 - WAN Interface Type is Static IP
If you selected Static IP you have to fill out the
IP address information provided to you by your ISP. You will need to complete all the required fields except for
Secondary DNS Server.
Click
Next
10
DFL-800 Quick Installation Guide
Step 7.2 - WAN Interface Type is PPPoE
If you selected PPPoE
(Point-to-Point Protocol over Ethernet) you will have to fill out the user name and password provided to you by your
ISP. The PPPoE Service
Name field should be left blank unless your ISP informs you otherwise.
Step 7.3 - WAN Interface Type is PPTP
Enter Username,
Password and the
PPTP Server IP address provided by your ISP.
DHCP:If your ISProvider is using DHCP you should select the DHCP radio button.
Static IP:If your Internet
Service Provider is using
Static IP you should select the Static IP radio button and enter
IP Address, choose a
Subnet Mask and enter the Gateway IP address.
11
Click
Next
Click
Next
DFL-800 Quick Installation Guide
Step 7.4 - WAN Interface Type is Big Pond
If you selected Big Pond you will have to fill out the user name and password provided to you by your
ISP.
Click
Next
and continue to step 8.
Click
Next
Step 8 - Set up built-in DHCP server
If you want to use the built-in DHCP Server in the DFL-800, choose
Enable DHCP Server in this screen. You then need to specify a range of IP addresses to hand out to the DHCP clients.
This range is entered in the format
“Start IP - Stop
IP” i.e. 192.168.0.100 -
192.168.0.200. If you don’t want to use the built-in
DHCP Server or configure it later, choose Disable
DHCP Server.
Click
Next
12
DFL-800 Quick Installation Guide
Step 9 - Configure helper servers
NTP Servers
If enabled, specify which
NTP Servers that should be used to syncronize the firewall time
Syslog Servers
If enabled, specify where the firewall should log, you can specify up to two Syslog recievers
Step10 - Setup Wizard Complete
Click
Activate
to complete your configuration.
Click
Next
13
Step 11 - Confirmation
Confirm the changes committed to the configuration file and it has been saved now.
DFL-800 Quick Installation Guide
Click
Close
14