- Computers & electronics
- Networking
- Call management system
- Premise Branch Exchange (PBX) systems
- Grandstream Networks
- UCM6100 Series
- User manual
advertisement
CHANGE LOG
This section documents significant changes from previous versions of the UCM6100 user manuals. Only major new features or major document updates are listed here. Minor updates for corrections or editing are not documented here.
FIRMWARE VERSION 1.0.10.39
Added multiple modes support for inbound route. [INBOUND ROUTE: MULTIPLE MODE]
Added option “Enable Inbound Multiple Mode”, “Inbound Default Mode” and “Inbound Mode 1” for
switching inbound route mode via feature code. [FEATURE CODES]
Added prepending prefix for inbound route. [INBOUND ROUTE: PREPEND EXAMPLE]
Added multiple registration per extension. [MULTIPLE REGISTRATIONS PER EXTENSION]
Added SIP Message support. [SMS MESSAGE SUPPORT]
Added 100rel option for 100rel support. [Table 89: SIP Settings/ToS]
Added video preview support. [Table 80: Internal Options/Payload]
Added User Portal Page Fax sending support. [USER PORTAL]
Added Fax intelligent routing. [FAX INTELLIGENT ROUTE]
Added Re-Invite with two media (audio, image) support for fax sending. [FAX WITH TWO MEDIA]
Added option “Max Concurrent Sending Fax” in Fax settings. [CONFIGURE FAX/T.38]
Added option “Fax Queue Length” in Fax settings. [CONFIGURE FAX/T.38]
Added Google Service Setting Support. [GOOGLE SERVICE SETTINGS SUPPORT]
Added Conference Schedule. [CONFERENCE SCHEDULE]
Added Setup Wizard. [SETUP WIZARD]
Added ability to customize specific prompt. [CUSTOMIZE SPECIFIC PROMPT]
Added option “ALL” when making backup file. [BACKUP/RESTORE]
Added “Enable Destination” and “Default Destination” in Follow Me settings. [FOLLOW ME]
Added “Call Duration Limit” option in web UI->PBX->Internal Options->General. [INTERNAL
Added “Enable Auto Email To User” option in web UI->PBX->Internal Options->General. [INTERNAL
Added options “ICE Support” and “STUN Server” in web UI->PBX->Internal Options->RTP Settings.
[INTERNAL OPTIONS/RTP SETTINGS]
Added payload type setting for VP8 in web UI->PBX->Internal Options->Payload. [INTERNAL
Added options “External Host” and “Use IP address in SDP” in web UI->PBX->SIP Settings->NAT. [SIP
Improved CDR. [CDR IMPROVEMENT]
Firmware Version 1.0.10.39 UCM6100 Series IP PBX User Manual Page 19 of 331
Added Network Status page under web UI->Maintenance->Troubleshooting->Network Status
FIRMWARE VERSION 1.0.9.26
Added Announcements Center [ANNOUNCEMENTS CENTER]
FIRMWARE VERSION 1.0.9.25
Added UCM Zero Config model templates for provisioning GXP2200EXT coupled with GXV3240.
Added ability to select the voicemail storage (Support Email + WAV). [VOICEMAIL EMAIL SETTINGS]
FIRMWARE VERSION 1.0.9.23
Added SSH enable/disable option in LCD or WEB [SSH ACCESS]
Added remote peer extensions in Ring Group [REMOTE EXTENSION IN RING GROUP]
Added ability to prepend digits in inbound routes [Table 58: Inbound Rule Configuration Parameters]
Added ability to search extensions on Extension page. [SEARCH AND EDIT EXTENSION]
Added user portal for users to log in with extension number, access user information, extension
configuration and CDR. [USER PORTAL]
Added support to send Fax via web UI. [FAX SENDING]
Added "Enable LDAP" option to skip the extension from UCM default LDAP phonebook. [Table 34: SIP
Extension Configuration Parameters->Basic Settings]
Added DDNS Support. [DDNS SETTINGS]
Added support for Call Barging using feature codes. [ENABLE SPY]
Added ability to search the CDR by called number. [Table 100: CDR Filter Criteria]
Added ability to select the file types for automatic backup. [BACKUP/RESTORE]
Added automatic backup support on SD Card or USB storage. [BACKUP/RESTORE]
Added support to skip trunk authentication by time condition. [Table 36: SIP Extension Configuration
Added option to send P-Asserted-Identity header in SIP Register Trunk. [Table 51: SIP Register Trunk
Added ability to specify trunks in CDR filters. [CDR]
Added ability to use Pattern in Caller Number to filter CDR. [CDR]
Added support to send UNREGISTER when VoIP trunk is disabled. [Table 51: SIP Register Trunk
Added LDAP Client support [LDAP CLIENT CONFIGURATIONS]
Added option to specify the chronological order of voice mails. [Table 63: Voicemail Settings]
Firmware Version 1.0.10.39 UCM6100 Series IP PBX User Manual Page 20 of 331
Added option to specify port range in Port Forwarding configuration. [Table 14: UCM6102 Network
Added ability to go back to IVR menu from Dial By Name by pressing the star key. [DIAL BY NAME
Added support to upgrade SIP end device via SD card in Zero Config. [Table 29: Global Policy
Added ability to filter alert logs. [ALERT LOG]
Added ability to delete alert logs. [ALERT LOG]
Added NAT option for peer trunk. [Table 52: SIP Peer Trunk Configuration Parameters]
Improved Automatic Download CDR result format. [CDR]
FIRMWARE VERSION 1.0.8.12
Added recording files store management. [RECORDINGS STORAGE]
Added AMI access (restricted). [ASTERISK MANAGER INTERFACE (RESTRICTED ACCESS)]
Added LDAP Phonebook Import/Export support. [LDAP PHONEBOOK]
Added Callback feature. [CALLBACK FEATURE]
Added Busy Camp-on (Call Completion) feature. [BUSY CAMP-ON]
Added external number calling via extension. [Table 36: SIP Extension Configuration
Added end point firmware management support to allow end point device to upgrade via UCM6100
local storage or USB media. [Table 29: Global Policy Parameters->Maintenance]
Added link to access phone web GUI in Zero Config. [MANAGE DEVICES]
Added model update support to download model templates for surveillance and GSWave. [MODEL
Added filter for searching in Alert Log. [ALERT LOG]
Added DAHDI Out Line Selection. [Table 48: Analog Trunk Configuration Parameters]
Added automatic CDR download. [CDR]
Added multi-user management and concurrent user login support. [USER MANAGEMENT]
Added operation log. [OPERATION LOG]
Added option to specify web access session timer. [LOGIN TIMEOUT SETTINGS]
Added call monitor/barge-in support. [ACTIVE CALLS AND MONITOR]
Added GSwave QR code support. [EMAIL TO USER]
Added ability to add customized Pvalue on Model Template. [MODEL TEMPLATES]
Updated maximum length of web UI login password to 30 characters. [CHANGE PASSWORD]
Added Fax gateway support for Fax mode on FXS and FXO port. [Table 43: FXS Extension
Configuration Parameters->Media] [Table 48: Analog Trunk Configuration Parameters]
Added “NAT” option and “Send PPI Header” option in SIP register trunk configuration. [Table 51: SIP
Register Trunk Configuration Parameters]
Added REC API (access for call recording files). [API CONFIGURATION]
Added “Synchronize All Data” option in Data Sync. [DATA SYNC]
Firmware Version 1.0.10.39 UCM6100 Series IP PBX User Manual Page 21 of 331
Added “Delect Selected Sound Files” option for Music On Hold files. [MUSIC ON HOLD]
FIRMWARE VERSION 1.0.7.11
Added office time and holiday setting. [OFFICE TIME] [HOLIDAY]
Added new architecture for auto provisioning via Zero Config. [PROVISIONING]
Added Alert-info configuration for distinctive ringing on inbound route. [Table 58: Inbound Rule
Added SLA support to monitor FXO trunk. [SLA STATION]
Added Follow Me support. [FOLLOW ME]
Added FXO Dial Delay option for analog trunk. [Table 48: Analog Trunk Configuration Parameters]
Added Music On Hold selection per extension. [EXTENSIONS]
Added Call Forward Time Condition per extension. [EXTENSIONS]
Added custom prompt support for ring group announcement. [Table 67: Ring Group Parameters]
Added custom prompt support for paging/intercom group announcement. [Table 68: Paging/Intercom
Group Configuration Parameters]
Added options to delete voicemail and Fax files via cleaner. [CLEANER]
Added DTMF configuration per trunk. [VOIP TRUNKS]
Added call queue Music On Hold customization. [Table 69: Call Queue Configuration Parameters]
Added call queue destination support. [Table 69: Call Queue Configuration Parameters]
Added batch add blacklist file support. [BLACKLIST CONFIGURATIONS]
FIRMWARE VERSION 1.0.6.11
Added service check options under web UI->Maintenance->Troubleshooting->Service Check page to regularly check Asterisk service.
FIRMWARE VERSION 1.0.6.10
Added static routes function. [STATIC ROUTES]
Added option to provision end devices’ date format, time format and time zone in zero config.
Added option to disable extension/trunk.
Added TEL URL support for extension/trunk.
Added option to dial trunk password per extensions.
Added export extension and import extension function. [EXPORT EXTENSIONS] [IMPORT
Added option "Need Registration" for SIP register trunk.
Added option "The Maximum Number of Call Line" for trunk.
Added Dial By Name. [DIAL BY NAME]
Firmware Version 1.0.10.39 UCM6100 Series IP PBX User Manual Page 22 of 331
Added voicemail password and Email address for voicemail group extension.
Added auto record support for ring group and call queue.
Added VFax file display, download and delete interface in web UI.
Changed web page name from "Hardware Config" to "Ports Config".
Added payload configuration for audio/video codecs. [INTERNAL OPTIONS/PAYLOAD]
Added activity calls status on web UI status page.
Added CDR API support. [API CONFIGURATION]
Added more alert events support such as Register SIP Failed, Register SIP Trunk Failed, Restore
Config, User Login Success, User Login Failed, SIP Internal Call Failure and etc. [ALERT EVENTS
FIRMWARE VERSION 1.0.5.19
Added built-in data migration tool to support upgrading from 1.0.4.7 to 1.0.5.19 without factory reset.
Added "Direct Dial Voicemail Prefix" feature code back. [Table 76: UCM6100 Feature Codes]
Changed valid range for option "Current Disconnect Threshold". [Table 48: Analog Trunk Configuration
FIRMWARE VERSION 1.0.5.14
New backend data structure and web UI performance improvement. 1.0.5.14 is not compatible with previous firmware versions. Once upgraded to 1.0.5.14, the device needs to be FULLY RESET and
RE-CONFIGURED MANUALLY.
Added traditional Chinese language for web UI. [WEB GUI LANGUAGES]
Updated LDAP configuration example. [LDAP SERVER]
Added "Enable Filter Source Caller ID" and "Custom Dynamic Route" options for outbound route
settings. [Table 57: Outbound Route Configuration Parameters]
Added more language support for voice prompt. [LANGUAGE SETTINGS FOR VOICE PROMPT]
Added "Ring Group Destination" for ring group configuration. [Table 67: Ring Group Parameters]
Added "Extension Groups" section in web UI. [EXTENSION GROUPS]
Added "Pickup Groups" section in web UI. [PICKUP GROUPS]
Added BLF function description. [BLF AND EVENT LIST]
Updated default extension range. [Table 77: Internal Options/General]
Added sample descriptions for downloaded CDR file. [DOWNLOADED CDR FILE]
FIRMWARE VERSION 1.0.4.7
Asterisk updated to version 1.8.23.1.
Added DID routing support for incoming calls. [Table 50: Create New SIP Trunk]
Added DOD routing support. [DIRECT OUTWARD DIALING (DOD)]
Added GXP one-button Voicemail access. [Table 34: SIP Extension Configuration Parameters]
Firmware Version 1.0.10.39 UCM6100 Series IP PBX User Manual Page 23 of 331
Added option "Skip voicemail password verification" on extension edit page. [Table 34: SIP Extension
Added Hot-Desking Support. [Table 34: SIP Extension Configuration Parameters]
Added one-button on-demand call recording for GXP
Add new option to enable or disable "FXS TISS Override" on Hardware Config page. [Table 90:
Internal Options/Ports Config]
Added more modes for FXS Two-Wire Impedance Synthesis
Added LDAP Sync manual trigger function and synced date displaying. [VOIP TRUNKS]
Improved LDAP Sync function, added retrying, file verifying and progress displaying function
Added option "Pick Extension Period" on auto-provision settings page of Zero Config
Added multiple extension assignment support on device edit page of Zero Config
Added "Reset All Extensions" button at the Zero Config page to recycle all assigned extensions.
Added system crash alarm, core dump detection and allow users to download core dump file. [Figure
179: System Events->Alert Events Lists: System Crash]
Add "Keep Trunk CID" option for VoIP trunks, and keep the priorities: DOD->Extension
CallerID->Trunk CallerID->Global CallerID. [Table 50: Create New SIP Trunk]
FIRMWARE VERSION 1.0.3.13
Added Fail2Ban support for SIP authentication. [FAIL2BAN]
Added voice prompt "Language" selection and "Auto Record" option for extension. [Table 34: SIP
Extension Configuration Parameters] [Table 46: Batch Add SIP Extension Parameters]
Added "Auto Record" option for trunk.
Added "Digit Timeout" option and voice prompt "Language" selection for IVR. [Table 62: IVR
Added "Direct Dial Voicemail Prefix" feature code to directly dial or transfer to extension's voicemail.
[Table 76: UCM6100 Feature Codes]
Added "Enforce Strong Passwords" option. [Table 77: Internal Options/General]
Added FXS MWI Mode. [Table 90: Internal Options/Ports Config]
Added system events with alert and Email notification support. [SYSTEM EVENTS]
Added new web page for recording files. [RECORDING FILES]
FIRMWARE VERSION 1.0.2.21
Added weight information. [Table 1: Technical Specifications]
Added NTP server support. [NTP SERVER]
Added Czech language for web GUI display. [WEB GUI LANGUAGES]
Added VLAN support. "Layer 2 QoS 802.1Q/VLAN tag" and "Layer 2 QoS 802.1p priority value"
options for network port settings are added. [NETWORK SETTINGS]
Updated LDAP client configurations information.
Firmware Version 1.0.10.39 UCM6100 Series IP PBX User Manual Page 24 of 331
Added sample Email settings. [EMAIL SETTINGS]
Added manual time settings. [TIME SETTINGS]
Added "Enable Pick Extension" and "Extension Segment" options for auto provisioning settings.
Changed one of the discovery method from "SIP MESSAGE (OPTIONS)" to "SIP MESSAGE
(NOTIFY)" in zero-config feature.
Added pickup group feature. [Table 76: UCM6100 Feature Codes]
Added PSTN detection instructions for "Auto Detect" and "Semi-auto Detect". [PSTN DETECTION]
Added "Auth ID" option for SIP register trunk configuration. [Table 50: Create New SIP Trunk]
Added LDAP sync options for peer SIP trunk. [Table 50: Create New SIP Trunk]
Changed the default setting of outbound route "Privilege Level" from "Internal" to "International" to avoid potential misconfiguration and security risk.
Added DISA and Fax to IVR key press event options. [Table 62: IVR Configuration Parameters]
Added "Min Message Time" option in voicemail settings. [Table 63: Voicemail Settings]
Added Fax setting samples. [FAX/T.38]
Added DISA support for inbound route and IVR.
Added Event List support to monitor local extensions and remote extensions. [BLF AND EVENT LIST]
Added feature code *0 for "Disconnect". [Table 76: UCM6100 Feature Codes]
Added feature code *8 for "Pickup Extension" in pickup group feature. [Table 76: UCM6100 Feature
Added "Record Prompt" and "Custom Name of Pickup Group" options in internal options. [Table 77:
Added warning information for "Allow Guest Call" option to avoid potential security risk caused by
misconfiguration. [Table 81: IAX Settings/General]
Changed reset mode to two mode "User Data" and "All". [RESET AND REBOOT]
FIRMWARE VERSION 1.0.1.22
This is the initial version.
Firmware Version 1.0.10.39 UCM6100 Series IP PBX User Manual Page 25 of 331
This page intentionally left blank
Firmware Version 1.0.10.39 UCM6100 Series IP PBX User Manual Page 26 of 331
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 19 GNU GPL INFORMATION
- 20 CHANGE LOG
- 20 FIRMWARE VERSION 1.0.10.39
- 21 FIRMWARE VERSION 1.0.9.26
- 21 FIRMWARE VERSION 1.0.9.25
- 21 FIRMWARE VERSION 1.0.9.23
- 22 FIRMWARE VERSION 1.0.8.12
- 23 FIRMWARE VERSION 1.0.7.11
- 23 FIRMWARE VERSION 1.0.6.11
- 23 FIRMWARE VERSION 1.0.6.10
- 24 FIRMWARE VERSION 1.0.5.19
- 24 FIRMWARE VERSION 1.0.5.14
- 24 FIRMWARE VERSION 1.0.4.7
- 25 FIRMWARE VERSION 1.0.3.13
- 25 FIRMWARE VERSION 1.0.2.21
- 26 FIRMWARE VERSION 1.0.1.22
- 28 WELCOME
- 30 PRODUCT OVERVIEW
- 30 TECHNICAL SPECIFICATIONS
- 34 INSTALLATION
- 34 EQUIPMENT PACKAGING
- 34 CONNECT YOUR UCM6100
- 34 CONNECT THE UCM6102
- 35 CONNECT THE UCM6104
- 36 CONNECT THE UCM6108
- 37 CONNECT THE UCM6116
- 38 SAFETY COMPLIANCES
- 38 WARRANTY
- 40 GETTING STARTED
- 40 USE THE LCD MENU
- 42 USE THE LED INDICATORS
- 43 USE THE WEB GUI
- 43 ACCESS WEB GUI
- 44 SETUP WIZARD
- 45 WEB GUI CONFIGURATIONS
- 46 WEB GUI LANGUAGES
- 46 SAVE AND APPLY CHANGES
- 46 MAKE YOUR FIRST CALL
- 48 SYSTEM SETTINGS
- 48 USER MANAGEMENT
- 48 USER PRIVILEGES
- 49 CREATE NEW WEB UI USER
- 51 USER PORTAL
- 52 CONCURRENT MULTI-USER LOGIN
- 52 OPERATION LOG
- 54 CHANGE PASSWORD
- 55 CHANGE BINDNG EMAIL
- 56 NETWORK SETTINGS
- 56 BASIC SETTINGS
- 63 802.1X
- 64 STATIC ROUTES
- 67 PORT FORWORDING (UCM6102 ONLY)
- 69 DDNS SETTINGS
- 71 FIREWALL
- 71 STATIC DEFENSE
- 74 DYNAMIC DEFENSE
- 75 FAIL2BAN
- 76 LDAP SERVER
- 77 LDAP SERVER CONFIGURATIONS
- 78 LDAP PHONEBOOK
- 81 LDAP CLIENT CONFIGURATIONS
- 83 HTTP SERVER
- 84 EMAIL SETTINGS
- 85 TIME SETTINGS
- 85 AUTO TIME UPDATING
- 87 SET TIME MANUALLY
- 87 OFFICE TIME
- 89 HOLIDAY
- 91 NTP SERVER
- 91 RECORDINGS STORAGE
- 93 LOGIN TIMEOUT SETTINGS
- 94 GOOGLE SERVICE SETTINGS SUPPORT
- 98 PROVISIONING
- 98 OVERVIEW
- 98 CONFIGURATION ARCHITECTURE FOR END POINT DEVICE
- 99 AUTO PROVISIONING SETTINGS
- 102 DISCOVERY
- 103 GLOBAL CONFIGURATION
- 103 GLOBAL POLICY
- 111 GLOBAL TEMPLATES
- 113 MODEL CONFIGURATION
- 113 MODEL TEMPLATES
- 115 MODEL UPDATE
- 116 DEVICE CONFIGURATION
- 116 CREATE NEW DEVICE
- 117 MANAGE DEVICES
- 124 SAMPLE APPLICATION
- 130 EXTENSIONS
- 130 CREATE NEW USER
- 130 CREATE NEW SIP EXTENSION
- 136 CREATE NEW IAX EXTENSION
- 140 CREATE NEW FXS EXTENSION
- 145 BATCH ADD EXTENSIONS
- 145 BATCH ADD SIP EXTENSIONS
- 148 BATCH ADD IAX EXTENSIONS
- 150 SEARCH AND EDIT EXTENSION
- 152 EXPORT EXTENSIONS
- 152 IMPORT EXTENSIONS
- 153 EMAIL TO USER
- 155 MULTIPLE REGISTRATIONS PER EXTENSION
- 156 SMS MESSAGE SUPPORT
- 158 TRUNKS
- 158 ANALOG TRUNKS
- 158 ANALOG TRUNK CONFIGURATION
- 161 PSTN DETECTION
- 164 VOIP TRUNKS
- 175 DIRECT OUTWARD DIALING (DOD)
- 178 SLA STATION
- 178 CREATE/EDIT SLA STATION
- 179 SAMPLE CONFIGURATION
- 182 CALL ROUTES
- 182 OUTBOUND ROUTES
- 184 INBOUND ROUTES
- 185 INBOUND RULE CONFIGURATIONS
- 186 INBOUND ROUTE: PREPEND EXAMPLE
- 187 INBOUND ROUTE: MULTIPLE MODE
- 188 FAX INTELLIGENT ROUTE
- 189 FAX WITH TWO MEDIA
- 189 BLACKLIST CONFIGURATIONS
- 192 CONFERENCE BRIDGE
- 192 CONFERENCE BRIDGE CONFIGURATIONS
- 194 JOIN A CONFERENCE CALL
- 194 INVITE OTHER PARTIES TO JOIN CONFERENCE
- 195 DURING THE CONFERENCE
- 196 RECORD CONFERENCE
- 198 CONFERENCE SCHEDULE
- 198 CONFERENCE SCHEUDLE CONFIGURATION
- 202 IVR
- 202 CONFIGURE IVR
- 204 CREATE CUSTOM PROMPT
- 204 RECORD NEW CUSTOM PROMPT
- 205 UPLOAD CUSTOM PROMPT
- 206 LANGUAGE SETTINGS FOR VOICE PROMPT
- 206 DOWNLOAD AND INSTALL VOICE PROMPT PACKAGE
- 208 CUSTOMIZE SPECIFIC PROMPT
- 210 VOICEMAIL
- 210 CONFIGURE VOICEMAIL
- 211 ACCESS VOICEMAIL
- 212 VOICEMAIL EMAIL SETTINGS
- 213 CONFIGURE VOICEMAIL GROUP
- 216 RING GROUP
- 216 CONFIGURE RING GROUP
- 218 REMOTE EXTENSION IN RING GROUP
- 222 PAGING AND INTERCOM GROUP
- 222 CONFIGURE PAGING/INTERCOM GROUP
- 224 CALL QUEUE
- 224 CONFIGURE CALL QUEUE
- 228 EXTENSION GROUPS
- 228 CONFIGURE EXTENSION GROUPS
- 229 USING EXTENSION GROUPS
- 230 PICKUP GROUPS
- 230 CONFIGURE PICKUP GROUPS
- 230 CONFIGURE PICKUP FEATURE CODE
- 232 MUSIC ON HOLD
- 234 FAX/T.38
- 234 CONFIGURE FAX/T.38
- 235 SAMPLE CONFIGURATION TO RECEIVE FAX FROM PSTN LINE
- 238 SAMPLE CONFIGURATION FOR FAX-TO-EMAIL
- 240 ASTERISK MANAGER INTERFACE (RESTRICTED ACCESS)
- 242 BUSY CAMP-ON
- 244 FOLLOW ME
- 248 ONE-KEY DIAL
- 250 DISA
- 252 CALLBACK FEATURE
- 254 BLF AND EVENT LIST
- 254 BLF
- 254 EVENT LIST
- 258 DIAL BY NAME
- 258 DIAL BY NAME CONFIGURATION
- 262 ACTIVE CALLS AND MONITOR
- 262 ACTIVE CALLS STATUS
- 264 HANG UP ACTIVE CALLS
- 264 CALL MONITOR
- 266 CALL FEATURES
- 266 FEATURE CODES
- 270 CALL RECORDING
- 271 CALL PARK
- 271 PARK A CALL
- 271 RETRIEVE THE PARKED CALL
- 271 ENABLE SPY
- 274 INTERNAL OPTIONS
- 274 INTERNAL OPTIONS/GENERAL
- 276 INTERNAL OPTIONS/JITTER BUFFER
- 277 INTERNAL OPTIONS/RTP SETTINGS
- 277 INTERNAL OPTIONS/PAYLOAD
- 280 IAX SETTINGS
- 280 IAX SETTINGS/GENERAL
- 280 IAX SETTINGS/REGISTRATION
- 281 IAX SETTINGS/STATIC DEFENSE
- 282 SIP SETTINGS
- 282 SIP SETTINGS/GENERAL
- 282 SIP SETTINGS/MISC
- 283 SIP SETTINGS/SESSION TIMER
- 283 SIP SETTINGS/TCP AND TLS
- 284 SIP SETTINGS/NAT
- 285 SIP SETTINGS/TOS
- 288 PORTS CONFIG
- 290 VALUE-ADDED FEATURES
- 290 FAX SENDING
- 290 ANNOUNCEMENTS CENTER
- 291 ANNOUNCEMENTS CENTER SETTINGS
- 291 GROUP SETTINGS
- 294 STATUS AND REPORTING
- 294 PBX STATUS
- 294 TRUNKS
- 295 EXTENSIONS
- 296 QUEUES
- 297 CONFERENCE ROOMS
- 298 INTERFACES STATUS
- 299 PARKING LOT
- 300 SYSTEM STATUS
- 300 GENERAL
- 301 NETWORK
- 301 STORAGE USAGE
- 302 RESOURCE USAGE
- 303 SYSTEM EVENTS
- 303 ALERT EVENTS LIST
- 305 ALERT LOG
- 306 ALERT CONTACT
- 306 CDR
- 309 CDR IMPROVEMENT
- 310 DOWNLOADED CDR FILE
- 312 STATISTICS
- 312 RECORDING FILES
- 313 API CONFIGURATION
- 316 UPGRADING AND MAINTENANCE
- 316 UPGRADING
- 316 UPGRADING VIA NETWORK
- 317 UPGRADING VIA LOCAL UPLOAD
- 319 NO LOCAL FIRMWARE SERVERS
- 319 BACKUP
- 319 BACKUP/RESTORE
- 322 DATA SYNC
- 323 RESTORE CONFIGURATION FROM BACKUP FILE
- 324 CLEANER
- 325 RESET AND REBOOT
- 326 SYSLOG
- 326 TROUBLESHOOTING
- 326 ETHERNET CAPTURE
- 327 IP PING
- 328 TRACEROUTE
- 328 ANALOG RECORD TRACE
- 329 SERVICE CHECK
- 329 NETWORK STATUS
- 330 REMOTE ACCESS
- 330 SSH ACCESS
- 332 EXPERIENCING THE UCM6100 SERIES IP PBX