advertisement
Page 6 AXIS P5534 Installation Guide
Install the hardware
The network camera can be mounted with the cables routed through or along the wall or ceiling.
!
IMPORTANT! - To use AXIS P5534 outdoors, it must be installed in an approved outdoor housing. Please see www.axis.com for more information on outdoor housing.
Prepare for installation
Read all the instructions before preparing to install AXIS P5534 since several installation preparation steps require removing the top cover and would benefit from being completed together.
• Follow the instructions
Remove the protective packaging
packing before installing AXIS P5534.
, below to remove the protective
• The AXIS P5534 is supplied with a clear transparent cover and a smoked transparent cover.
If required, follow the instructions
Replace the clear/smoked dome cover (optional)
, below to replace the dome cover.
• A standard or high capacity SD card (not included) is required to store images locally in the network camera. Follow the instructions top cover and install an SD card.
Install an SD card (optional)
, below to remove the
Remove the protective packaging
1. Loosen the 4 top cover screws and remove the top cover, see illustration on page 5.
2. Remove the protective packaging.
Protective packaging
3. If replacing the clear/smoked dome cover or installing an SD card, refer to the instructions
Replace the clear/smoked dome cover (optional)
and
Install an SD card (optional)
4. Put the top cover back in its original position and fasten the screws.
AXIS P5534 Installation Guide Page 7
Replace the clear/smoked dome cover (optional)
1. Loosen the 4 top cover screws and remove the top cover, see illustration on page 5.
2. Remove the 6 dome ring screws and remove the dome ring from the top cover.
3. Attach the dome ring and the dome cover to the top cover and secure by tightening the 6 screws.
4. If installing an SD card, refer to the instructions
Install an SD card (optional)
, below.
5. Put the top cover back in its original position and fasten the screws.
Note:
Be careful not to scratch or damage the dome cover. Use a soft cloth to wipe clean before attaching the dome cover to the camera unit.
Install an SD card (optional)
1. Loosen the 4 top cover screws and remove the top cover, see illustration on page 5.
2. Insert an SD card (not included) into the SDHC (Secure Digital High Capacity) card slot.
3. Put the top cover back in its original position and fasten the screws.
Notes:
The SD card is automatically mounted when inserted into the SDHC card slot. However, before removing the SD card it should be unmounted through the camera’s web pages. Go to
Setup > System Options > Storage > SD Card and click Unmount. For more information, please see the User’s Manual available from the AXIS Network Video Product CD supplied with this product or from the website at www.axis.com
Hard ceiling mount
1. Prepare the ceiling for installation of the mounting plate, use the supplied drill template to position the holes. Make sure to use drill bits, screws, and plugs that are appropriate for the material.
2. Install the mounting plate.
Mounting plate
Security wire
3. Loosen the 4 camera base lid screws and remove the camera base lid, see illustration on page 5.
Page 8 AXIS P5534 Installation Guide
4. Route and connect the network cable and the multi-connector cable, if applicable, to the network camera. Be careful not to damage the cables when connecting them. Make sure the foam gasket holes are aligned with the cable tracks and, if applicable, remove the cut-out piece for the multi-connector cable from the foam gasket.
5. Put the camera base lid back in its original position and fasten the screws.
6. Secure the camera using the supplied safety wire.
7. Slide the unit holders on the network camera into the slots on the mounting plate and rotate the camera unit.
8. Install the High PoE Midspan 1-Port, see page 11.
Install the AXIS T8123 High PoE Midspan 1-port,
9. Check that the indicator LEDs on the midspan indicate the correct conditions, see the table on
Drop ceiling mount
1. Remove the ceiling tile in which the drop ceiling mount is to be fitted.
2. Use the supplied template to mark the position for the 210 mm (8.3 in.) hole in the ceiling tile.
Cut around the template.
Ceiling tile
Hole diameter
210 mm (8.3 in.)
Notes:
• The combined weight of the camera and ceiling mount is approximately 2.3 kg (5.1 lb.). Check that the ceiling material is strong enough to support this weight.
• The ceiling tile should be 5 mm–60 mm (0.2 in.–2.4 in.) thick.
3. Put the ceiling bracket into the ceiling tile, see illustration on page 9.
4. Tighten the bracket arm screws using a torx 20 screwdriver head.
5. Loosen the 4 camera base lid screws and remove the camera base lid, see illustration on page 5.
AXIS P5534 Installation Guide Page 9
6. Route and connect the network cable and the multi-connector cable, if applicable, to the network camera. Be careful not to damage the cables when connecting them. Make sure the foam gasket holes are aligned with the cable tracks and, if applicable, remove the cut-out piece for the multi-connector cable from the foam gasket.
Multi-connector cable
Network cable
7. Put the camera base lid back in its original position and fasten the screws.
8. Secure the camera using the supplied safety wire.
Ceiling bracket
Safety wire
Ceiling tile
9. Slide the unit holders on the network camera into the slots on the mounting plate and rotate the camera unit.
10. Install the High PoE Midspan 1-Port, see page 11.
Install the AXIS T8123 High PoE Midspan 1-port,
11. Check that the indicator LEDs on the midspan indicate the correct conditions. See the table on
12. Install the ceiling tile, with the camera mounted, into the ceiling.
Page 10 AXIS P5534 Installation Guide
13. Place the plastic dome cover over the ceiling bracket and snap it into place.
Plastic dome cover
Bracket mount (optional accessory)
1. Install the selected bracket according to the instructions supplied with the bracket. If drilling is required, make sure to use drill bits, screws, and plugs that are appropriate for the material.
2. Loosen the 4 camera base lid screws and remove
the camera base lid, see illustration on page 4.
3. Route the network cable and the multi-connector cable, if applicable, through the holes in the mounting bracket.
Safety wire
4. Hook the camera to the safety wire on the bracket.
5. Connect the network cable and, if applicable, the multi-connector cable to the network camera.
Wall bracket (mounting example)
Install the AXIS T8123 High PoE Midspan 1-port,
Torx T30
Screws
Slots for unit holders
7. Put the camera base lid back in its original position.
8. Slide the unit holders on the network camera into the slots on the bracket and rotate the camera unit.
9. Secure the network camera to the mounting bracket by fastening the 3 screws (Torx T30).
AXIS P5534 Installation Guide Page 11
Install the AXIS T8123 High PoE Midspan 1-port
AXIS T8123 High PoE Midspan 1-port enables Axis network video products with high power consumption to receive data and power over the same Ethernet cable. Follow these instructions to connect AXIS T8123.
1. Connect AXIS T8123 (Data in) to the network switch using a standard network cable.
2. Connect AXIS T8123 (Data and Power Out) to the network camera, using the network cable that has been connected to the camera.
3. Connect AXIS T8123 to an AC outlet (100–240 V AC), using the supplied power cable.
AXIS T8123
Port connectivity indicator
Data &
Power out Data in
AC Input connectivity indicator
Network camera Ethernet
For information on the LEDs on the midspan, see
AXIS T8123 Status indicators,
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 Installation Steps
- 3 Package Contents
- 4 Hardware Overview
- 6 Install the hardware
- 6 Prepare for installation
- 7 Hard ceiling mount
- 8 Drop ceiling mount
- 10 Bracket mount (optional accessory)
- 11 Install the AXIS T8123 High PoE Midspan 1-port
- 12 Assign an IP Address
- 13 AXIS IP Utility - single camera/small installation
- 14 AXIS Camera Management - multiple cameras/large installations
- 14 Assign IP addresses in multiple devices
- 15 Set the Password
- 16 Access the video stream
- 17 Other Methods of Setting the IP address
- 18 Set the IP address with ARP/Ping
- 19 Unit Connectors
- 20 Multi-connector cable (not included)
- 21 AXIS P5534 Status indicators
- 21 AXIS T8123 Status indicators
- 22 Resetting to the Factory Default Settings
- 22 Accessing the Camera from the Internet
- 22 Further Information
- 23 Procédure d’installation
- 23 Contenu de l’emballage
- 24 Présentation du matériel
- 26 Installation du matériel
- 26 Préparation de l’installation
- 27 Fixation au plafond
- 28 Fixation au faux-plafond
- 30 Fixation du support (accessoire en option)
- 31 Installation de l’injecteur High PoE AXIS T8123 à 1 port
- 32 Attribution d’une adresse IP
- 33 AXIS IP Utility : une seule caméra et une petite installation
- 34 AXIS Camera Management : plusieurs caméras et de grandes installations
- 35 Attribution d’adresses IP à plusieurs périphériques
- 35 Configuration du mot de passe
- 37 Accès au flux de données vidéo
- 38 Autres méthodes de configuration de l’adresse IP
- 39 Définition de l’adresse IP à l’aide d’ARP/Ping
- 40 Connecteurs de l’appareil
- 41 Câble multi-connexion (non fourni)
- 42 AXIS P5534 Voyants d’état
- 43 Voyants d’état AXIS T8123
- 43 Rétablissement des paramètres d’usine par défaut
- 44 Accès à la caméra via Internet
- 44 Plus d’informations
- 45 Installationsschritte
- 45 Lieferumfang
- 46 Hardwareübersicht
- 48 Installieren der Hardware
- 48 Vorbereitung der Installation
- 50 Deckenmontage
- 51 Hängedeckenmontage
- 53 Montagehalterung (Sonderzubehör)
- 54 Installation des AXIS T8123 High PoE Midspan (1 Anschluss)
- 55 Zuweisen einer IP-Adresse
- 56 AXIS IP Utility - einzelne Kamera/kleine Installation
- 57 AXIS Camera Management - mehrere Kameras/große Installationen
- 58 Zuweisen von IP-Adressen für mehrere Geräte
- 58 Festlegen des Kennworts
- 60 Zugriff auf den Videostrom
- 61 Andere Methoden zum Festlegen der IP-Adresse
- 62 Zuweisen der IP-Adresse per ARP/Ping
- 63 Geräteanschlüsse
- 64 Mehrfachanschlusskabel (separat erhältlich)
- 65 AXIS P5534 Statusanzeigen
- 66 AXIS T8123 Statusanzeigen
- 66 Wiederherstellen der werkseitigen Standardeinstellungen
- 67 Zugriff auf die Kamera über das Internet
- 67 Weitere Informationen
- 69 Procedura di installazione
- 69 Contenuto della confezione
- 70 Panoramica dell'hardware
- 72 Installazione dell'hardware
- 72 Preparazione dell'installazione
- 73 Montaggio su controsoffitto
- 74 Montaggio su soffitto mobile
- 76 Montaggio su staffa (accessorio opzionale)
- 76 Installare il Midspan AXIS T8123 High PoE a 1 porta
- 77 Assegnazione di un indirizzo IP
- 78 AXIS IP Utility: telecamera singola/piccole installazioni
- 79 AXIS Camera Management: più telecamere/grandi installazioni
- 80 Assegnazione degli indirizzi IP a più telecamere
- 80 Impostazione della password
- 82 Accesso al flusso video
- 83 Altri metodi di assegnazione dell'indirizzo IP
- 84 Assegnazione dell'indirizzo IP con ARP/Ping
- 85 Connettori
- 86 Cavo multiplo (non incluso)
- 87 AXIS P5534 Indicatori di stato
- 87 Indicatori di stato AXIS T8123
- 88 Ripristino delle impostazioni predefinite
- 88 Accesso alla telecamera da Internet
- 88 Ulteriori informazioni
- 89 Pasos para la instalación
- 89 Contenido del paquete
- 90 Presentación del hardware
- 92 Instalación del hardware
- 92 Preparación para la instalación
- 93 Montaje en techo duro
- 94 Montaje en falso techo
- 96 Montaje con escuadra (accesorio opcional)
- 97 Instalación del midspan High PoE AXIS T8123 con 1 puerto
- 98 Asignación de una dirección IP
- 99 AXIS IP Utility: para cámaras individuales o instalaciones pequeñas
- 100 AXIS Camera Management: para varias cámaras o instalaciones grandes
- 101 Asignación de direcciones IP en varios dispositivos
- 101 Configuración de la contraseña
- 103 Acceso al vídeo continuo
- 104 Otros métodos para configurar la dirección IP
- 105 Configuración de la dirección IP con ARP/Ping
- 106 Conectores de la unidad
- 107 Cable multiconector (no incluido)
- 108 Indicadores de estado de la cámara AXIS P5534
- 108 Indicadores de estado del dispositivo AXIS T8123
- 109 Restablecimiento de los valores iniciales
- 109 Acceso a la cámara desde Internet
- 109 Más información