advertisement
UF6300_FAX_UK_PJQMC1263ZB.book 36 ページ 2008年12月10日 水曜日 午後1時26分
Customizing Your Machine
Fax Parameter Table
No.
Parameter
01 CONTRAST (HOME)
02
04
05
06
07
08
09
10
12
13
17
RESOLUTION
(HOME)
STAMP (HOME)
MEMORY (HOME)
DIALLING METHOD
HEADER PRINT
HEADER FORMAT
RCV'D TIME PRINT
KEY/BUZZER
VOLUME
COMM. JOURNAL
(HOME)
AUTO JRNL PRINT
RECEIVE MODE 1
2
1
2
3
3
1
1
2
2
3
1
2
1
2
3
1
Setting
Number
3
1
1
2
2
3
4
5
2
1
2
1
2
1
2
4
Setting Comments
NORMAL Setting the home position of the CONTRAST key.
LIGHTER
DARKER
STANDARD Setting the home position for the RESOLUTION.
FINE
S-FINE
HALFTONE
(FINE)
HALFTONE
(S-FINE)
OFF
ON
OFF
ON
Setting the home position of the STAMP key.
To select the stamp function when document is stored in memory, see Fax Parameter No. 28.
Setting the home position for memory transmission/copy mode. (This setting can be temporarily changed by using
F8-9 (MEMORY XMT))
Selecting the dialling method.
PULSE
TONE
INSIDE
OUTSIDE
NO PRINT
Selecting the printing position of the header.
INSIDE
: Inside TX copy area.
OUTSIDE : Outside TX copy area.
NO PRINT : Header is not printed.
Selecting the header format.
LOGO, ID
NO.
FROM TO
INVALID Selecting whether the machine prints the received date &
VALID time, remote ID, percentage of reduction and page number on the bottom of each received page.
OFF
SOFT
Selecting the volume of the Key/Buzzer tone.
LOUD
OFF
ALWAYS
INC. ONLY
Selecting the home position of printout mode for COMM.
Journal Off/Always/INC.
OFF
: Does not print
ALWAYS : Always prints
INC. ONLY: Prints only when communication has failed.
INVALID Selecting whether the machine prints the journal
VALID automatically after every 32 transactions.
TEL
FAX
Setting the receive mode.
FAX/TEL
SW.
TAM/FAX
36
Downloaded From ManualsPrinter.com Manuals
UF6300_FAX_UK_PJQMC1263ZB.book 37 ページ 2008年12月10日 水曜日 午後1時26分
Customizing Your Machine
No.
18
19
Parameter
OP CALL TIMER
OGM LENGTH
(TAM I/F)
20 SILENT DETECTION
(TAM I/F)
22 SUBSTITUTE RCV
23
24
REC. PAPER SIZE
PRINT REDUCTION
Setting
Number
1
---
60
3
4
1
2
1
2
1
2
3
1
1
2
2
25
26 POLLING PASSWORD
27 POLLED FILE SAVE
28 STAMP AT MEMORY
XMT
30 DRD
31
32
REDUCTION RATIO
INC. FILE SAVE
COPY REDUCTION
1
2
1
2
1
2
1
2
1
2
70
----
100
Setting Comments
20SEC
30SEC
40SEC
50SEC
Selecting the length of time that your machine signals
(rings) for an incoming voice call in Fax/Tel Auto Switching mode. (See page 68)
1SEC
---
60SEC
Setting for the OGM length of your TAM from 1 to 60 seconds. The machine will not start to detect SILENCE until the time setting has lapsed.
(Default = 20 sec.)
INVALID Selecting the Silent Detection Mode.
VALID
INVALID Selecting whether the machine receives to memory when
VALID recording paper runs out, toner runs out or recording paper is jammed.
A4
LETTER
Setting the recording paper size installed in your machine.
LEGAL
FIXED
AUTO
Selecting print reduction mode.
FIXED : Reduce received document according to setting of
Parameter No. 25.
AUTO : Reduce received document according to the length of received documents.
70%
----
Selecting fixed print reduction ratio from 70% to 100%.
This parameter functions only when fixed print reduction is selected on Fax Parameter No. 24.
100%
(----) Setting a 4-digit password for secured polling.
INVALID Selecting whether the machine retains the polled
VALID document in memory even after the document is polled once.
INVALID Selecting whether the machine stamps the original
VALID documents when storing the documents into memory.
(Depending on the Stamp setting on the Control Panel)
INVALID Selecting whether or not the machine is available "DRD
VALID
Service". If this parameter is set to "VALID", your machine detects the specified ring pattern only to receive a document automatically.
INVALID Selecting whether the machine retains the document in
VALID memory if the document is not successfully transmitted.
MANUAL Selecting whether the machine performs the copy
AUTO reduction ratio automatically or manually.
MANUAL: The machine will prompt you for the Zoom ratio
(100% to 70%) when making copies.
AUTO
: The machine will automatically determine the reduction ratio according to the length of the original document.
Continued on the next page...
37
Downloaded From ManualsPrinter.com Manuals
UF6300_FAX_UK_PJQMC1263ZB.book 38 ページ 2008年12月10日 水曜日 午後1時26分
Customizing Your Machine
Fax Parameter Table
No.
34
35
37
38
39
Parameter
ENERGY SAVER
MODE
DAYLIGHT TIME
RCV TO MEMORY
ACCESS CODE
PIN CODE ACCESS
42 CONF. POLLED FILE
SAVE
43 PASSWORD-XMT
44
46
47
48
PASSWORD-RCV
SELECT RCV
REMOTE RCV
TELEPHONE LINE
49 PSTN ACCESS CODE
2
1
2
3
1
1
2
1
2
1
2
1
2
1
2
Setting
Number
1
2
3
1
2
Setting Comments
OFF
ENERGY
SAVER
SLEEP
To reduce the power consumption in standby, select either
Energy-Saver or Sleep mode and specify the Delay Time
(1 to 120 minutes) for the machine to enter into the selected mode.
The Delay Timer setting is only available in the Energy-
Saver or Sleep Modes.
OFF
: The unit will remain in standby mode and consume more energy than when in Energy-Saver or Sleep modes.
ENERGY SAVER: Saves energy by consuming less power than when in standby mode by turning off the fuser unit after the
SLEEP
specified time.
: This is the lowest power state that the machine enters after the specified time without actually turning off.
INVALID Selecting whether the clock adjusts for Daylight Saving
VALID
Time automatically. The built-in clock will advance 1 hour at 2:00 am on the last Sunday in March and go back 1 hour at 3:00 am on the last Sunday in October.
(----) Enter a 4-digit password used to print out the received document in memory by using F8-5 (RCV TO MEMORY).
When F8-5 is set to ON, this parameter will not be shown on the LCD display. (See page 96)
(----)
NONE
SUFFIX
OFF
ON
OFF
ON
Enter a 4-digit Access Code to secure the machine from unauthorized use. (See page 94)
Selecting the access method (Prefix or Suffix) to dial a number with PIN Code. (See page 106)
PREFIX
INVALID Selecting whether the machine saves the confidential
VALID polled file even after the file is polled once.
Setting a 4-digit XMT-Password and selecting whether the machine performs and checks the XMT-Password of the receiving station when transmitting. (See page 111)
Setting a 4-digit RCV-Password and selecting whether the machine performs and checks the RCV-Password of the transmitting station when receiving. (See page 112)
INVALID Selecting whether the machine performs selective
VALID reception. (See page 109)
INVALID Selecting whether or not the machine accepts remote
VALID reception command. (See page 67)
PSTN
PBX
Selecting the type of line connected.
(----) Setting PSTN Access Code. (Up to 4 digits)
38
Downloaded From ManualsPrinter.com Manuals
ti3.fm 39 ページ 2009年1月26日 月曜日 午後6時41分
Customizing Your Machine
No.
51
52
53
54
56
58
63
65
Parameter
REMOTE
DIAGNOSTIC
DIAGNOSTIC
PASSWORD
SUB-ADDRESS
PSWD
FAX FORWARD
COVER SHEET
LANGUAGE
PC-FAX RCV MODE
(For UF-6300 only)
PRINT COLLATION
82 QUICK MEMORY XMT
99
117
MEMORY SIZE
(Flash Memory)
MULTI STATION
(HOME)
125 CONFIRM STATIONS
Setting
Number
1
2
1
2
1
2
1
2
3
1
2
1
2
-
Setting Comments
INVALID Selecting whether or not the machine accepts to update
VALID the firmware or Remote Diagnostics from the remote station. Please ask your Panasonic Authorized Dealer for details.
(----) Setting the password for Remote Diagnostic Mode.
Please ask your Panasonic Authorized Dealer for details.
(----) Setting a 20-digit password for secured sub-address communication.
INVALID Selecting whether the machine performs Fax Forwarding
VALID to the specified destination. (See page 108)
OFF
ON
Setting the home position of the Cover Sheet parameter in the Select Mode. (See page 104)
UPLD&PRT
UPLOAD
Selecting the language to be shown on the display and reports.
Selecting how the machine will execute the received Fax document(s). If the setting is set to either "Upload" or
"Upload & Print" the machine cannot enter the Sleep Mode.
: Print the received document(s).
UPLD&PRT: Print the received document(s) and upload it’s file.
UPLOAD
: Upload the received document file.
INVALID Selecting whether the machine prints out documents in
VALID sequence. (See page 74)
INVALID Selecting whether the machine performs Quick Memory
VALID
Transmission. (See pages 49 to 52)
INVALID: Stores all documents into memory first before dialling the telephone number.
VALID : Starts dialling the telephone number immediately after storing the first page.
Is not available when the No.133 Job Build is set to
"2:ON".
Displays the memory size.
1
2
1
2
INVALID Set the default setting for the Multi Station function.
VALID
INVALID: The document is sent to a single destination only.
VALID : Allows sending the document to multiple destinations.
INVALID Set whether to confirm the destinations.
VALID
When set to Valid the document cannot be sent unless the destination is confirmed.
This function also operates when the addresses are specified with Group Dialling or Program Dialling function.
If an address has been altered (Added or removed) when confirming addresses, address confirmation message will appears again when transmitting the documents (Pressing the start key).
Continued on the next page...
39
Downloaded From ManualsPrinter.com Manuals
UF6300_FAX_UK_PJQMC1263ZB.book 40 ページ 2008年12月10日 水曜日 午後1時26分
Customizing Your Machine
Fax Parameter Table
No.
133
135
136
137
Parameter
JOB BUILD
JUNK FAX FILTER
RESTRICT D. DIAL
RE-ENTER D. DIAL
Setting
Number
Setting Comments
1
2
OFF
ON
1. JUNK FAX FILTER
1
2
INVALID
VALID
Selecting whether the machine performs Job Build when the total number of documents exceed the maximum capacity of the ADF, or when scanning the documents manually one at a time. If you place the documents on the
ADF within 5 seconds after the ADF scan, the ADF scan will continue for the current scan. (Maximum number of scanning papers is 255 pages for one job.)
The Quick Memory Transmission feature (Fax Parameter
No. 82) is not available when the Job Build is set to
"2:ON".
Up to 250 pages can be stored. When the number of pages exceeds 255, the memory overfull message will be displayed. Select "Yes" to start transmitting, or "No" to cancel. If no action is taken within 5 seconds, the machine will start transmitting the stored originals.
Function to prevent direct mail FAX and unnecessary FAX messages.
When set to "VALID", the machine will not receive the faxes from the senders whose numeric ID has been registered as junk fax number. The denied number IDs can be registered in "4.ID NO. REGISTRATION".
2. RECEIVE WITHOUT ID
NO.
1
2
INVALID
VALID
When set to "VALID", the machine will receive the faxes from senders without numeric ID registered.
(This setting is available only when "1. JUNK FAX FILTER" is set to "VALID".)
3. RECEIVED ID PRINT When set to "VALID", the sender’s numeric ID and
1 INVALID received time are printed at the bottom of the received faxes. If the sender’s numeric ID is not registered, only the
2 VALID received time is printed. (This setting is available only when "1. JUNK FAX FILTER" is set to "VALID".)
4. ID NO.
REGISTRATION
(NO. 01-30)
Register fax numbers as junk fax number.
Up to 30 fax numbers can be registered for junk fax number. (Including numerals "0-9", blank space, and + symbol.) (When comparing the sender's numeric ID to the registered junk fax numbers, blank spaces between numbers are ignored.)
1
2
1
2
INVALID Enable or disable the Restrict Direct Dial function.
VALID
When set to "VALID", manual input destination Tel No. and
"Redial" button are not accepted.
INVALID Used to set whether to display the address reinsert screen
VALID when indicating the address for direct dial, inputting the mail address for Internet FAX, redialing or inputting the address for confirming the address. When set to "VALID", unit will require input destination Tel No. or Mail address twice for confirmation. Unit will proceed transmit job when destination data is matched.
This setting is not available when the Restrict Direct Dial function is set to "VALID".
NOTE
1. The standard settings are printed on the Fax Parameter List. To print out Fax Parameter List.
(See page 135)
2. The contents of Fax Parameter may differ depending on regulations and specifications in the countries.
40
Downloaded From ManualsPrinter.com Manuals
UF6300_FAX_UK_PJQMC1263ZB.book 41 ページ 2008年12月10日 水曜日 午後1時26分 memo
Downloaded From ManualsPrinter.com Manuals
41
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 12 Precautions
- 13 External View
- 14 Control Panel
- 16 Function Key
- 17 Connecting the Telephone Line Cable and Power Cord
- 18 Installing the Toner Cartridge
- 20 Loading the Recording Paper
- 20 How to Load the Recording Paper
- 22 Adjusting the Paper Cassette for the Paper Length
- 22 How to Adjust the Paper Cassette for the Paper Length
- 23 Adjusting the Paper Cassette for the Paper Width
- 23 How to Adjust the Paper Cassette for the Paper Width
- 24 Setting the Dialling Method (Tone or Pulse)
- 25 Adjusting the Volume
- 26 User Parameters
- 26 General Description
- 26 Setting the Date and Time
- 27 Setting Your LOGO
- 28 Setting Your Character ID
- 29 Setting Your ID Number (Fax Telephone Number)
- 30 One-Touch/Abbreviated Dialling Numbers
- 30 Entering One-Touch/Abbreviated Dialling Numbers
- 32 Editing One-Touch/Abbreviated Dialling Numbers
- 34 Printing Out a Directory Sheet
- 35 Customizing Your Machine
- 35 General Description
- 35 Setting the Fax Parameters
- 36 Fax Parameter Table
- 42 Loading Documents
- 42 Documents You Can Send
- 42 Documents You Cannot Send
- 43 How to Load Documents
- 44 Basic Transmission Settings
- 44 General Description
- 44 Contrast
- 44 Resolution
- 45 Verification Stamp
- 46 Communication Journal (COMM. JOURNAL)
- 47 Sending Documents
- 47 General Description
- 49 Memory Transmission
- 54 Wrong Transmission Prevention Function
- 57 Direct Transmission
- 60 Voice Mode Transmission
- 62 Transmission Reservation
- 65 Redialling
- 66 Receiving Documents
- 66 Reception Modes
- 67 Telephone Mode
- 68 Fax / Tel Auto Switching Mode
- 69 Fax Mode
- 70 TAM (Telephone Answering Machine) Interface Mode
- 72 Print Reduction
- 73 Receiving Oversize Documents
- 74 Substitute Memory Reception
- 74 Print Collation Mode
- 75 Making Copies
- 75 Copies
- 76 Timer Controlled Communications
- 76 General Description
- 76 Deferred Transmission
- 77 Deferred Polling
- 78 Polling
- 78 General Description
- 78 Setting the Polling Password
- 79 Preparing to be Polled
- 80 To Poll Documents from Another Station
- 81 Program Keys
- 81 General Description
- 81 Setting for Group Dialling
- 82 Setting for Deferred Transmission
- 83 Setting for Deferred Polling
- 84 Setting for Normal Polling
- 85 Setting for One-Touch Key
- 86 Changing or Erasing the Program Key Settings
- 87 Edit File Mode
- 87 General Description
- 87 Printing a File List
- 88 Viewing the Contents of a File List
- 89 Changing the Start Time or the Station of a File
- 90 Deleting a File
- 91 Printing Out a File
- 92 Adding Documents into a File
- 93 Retry an Incomplete File
- 94 Access Code
- 94 General Description
- 94 Setting the Access Code
- 95 Operating Your Machine with the Access Code (Restrict all operations)
- 95 (Restrict access of Fax Parameters only)
- 96 Receive To Memory
- 96 General Description
- 96 Setting the RCV To Memory Password
- 96 Setting RCV To Memory
- 97 Printing Out Documents
- 98 Possibility of filtering unnecessary incoming faxes
- 98 General Description
- 99 Set the Filter
- 100 Receive without ID
- 101 Received ID Print
- 102 Register Junk Fax Number
- 103 Distinctive Ring Detector (DRD)
- 103 General Description
- 104 Fax Cover Sheet
- 104 General Description
- 104 To use the Fax Cover Sheet
- 106 PIN Code Access
- 106 General Description
- 106 Selecting the Access Method (Prefix or Suffix)
- 107 Dialling with a PIN Code
- 108 Fax Forward
- 108 Setting Fax Forward
- 109 Selective Reception
- 109 General Description
- 109 Setting the Selective Reception
- 110 Password Communications
- 110 General Description
- 110 Compatibility with Other Machines
- 111 Setting Password Transmission
- 112 Setting Password Reception
- 113 Using Password Transmission
- 114 Using Password Reception
- 115 Confidential Mailbox
- 115 General Description
- 115 Confidential Mailbox
- 116 Sending a Confidential Document to a Remote Station's Mailbox
- 117 Polling a Confidential Document from a Remote Station's Mailbox
- 118 Receiving a Confidential Document to Your Machine's Mailbox
- 119 Storing a Confidential Document in Your Machine's Mailbox
- 120 Printing Out a Confidential Document from Your Machine's Mailbox
- 121 Deleting a Confidential Document Stored in Your Machine's Mailbox
- 122 Sub-addressing
- 122 General Description
- 123 To set the Sub-address into a One-Touch/ABBR. Dialling Numbers
- 124 To send a Document with Sub-address
- 125 Journals and Lists
- 125 General Description
- 125 Transaction Journal
- 126 Individual Transmission Journal (IND. XMT JOURNAL)
- 129 Communication Journal (COMM. JOURNAL)
- 131 One-Touch/Abbreviated and Directory Search List
- 134 Program List
- 135 FAX Parameter List
- 136 Toner Cartridge Order Forms
- 137 Troubleshooting
- 141 Information Codes
- 144 Clearing a Recording Paper Jam
- 145 Clearing a Document Jam
- 146 Cleaning the Document Scanning Area
- 147 Cleaning the Printer Roller
- 148 Adjusting the Automatic Document Feeder (ADF)
- 149 Verification Stamp
- 150 Checking the Telephone Line
- 151 Specifications
- 153 Recording Paper Specifications
- 154 Options and Supplies
- 155 Regulatory Information
- 158 Glossary
- 161 ITU-T Image No
- 162 Index