advertisement
16.8 EQUALISER
STEREO MODULE
ENG
The Equaliser (available as an option – Ref to Section 10) comprises three sections. The upper control provides H.F.(treble) boost and cut of +/-
15dB at 13 kHz, and the lower control provides L.F. (bass) boost and cut of +/-15dB at 60 Hz.
The centre knob is arranged as MID frequency section, with a cut/boost control of +/- 15dB for frequencies at around 5 KHz.
Set the cut/boost control of each section to the centre-detented position when not required.
16.9 BALANCE
It adjusts the stereo image of the signal on the stereo line input (i.e. the balance between the L and R outputs). At the detented centre position the signal routes equally to L and R.
16.10 MASTER-SUB ROUTING SWITCHES
The input channel signal may be routed to the main Stereo MIX (L-R) and/or to the SUB bus by pressing the respective switches.
There is a red LED inside each switch which will illuminate accordingly.
The Sub mix can be mixed into the main output mixbus (Master) (see
MASTER routing switcher on the Sub module). This is a convenient way to use the SUB assigment switch as a subgroup system, creating new possibilities in the Oxygen 4 console.
36
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 TABLE OF CONTENTS
- 6 SAFETY WARNINGS / ISTRUZIONI PER LA SICUREZZA
- 6 FOREWORD
- 7 SAFETY WARNINGS
- 8 CONSIGNES DE SÉCURITÉ IMPORTANTES
- 9 ISTRUZIONI IMPORTANTI PER LA SICUREZZA
- 10 WICHTIGE SICHERHEITSHINWEISE
- 11 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 12 UNPACKING AND INSPECTION
- 13 FIRST INSTALLATION RECOMMENDATIONS
- 13 CABLE
- 14 REPLACEMENT
- 14 LIGHTNING
- 14 VENTILATION
- 15 EARTHING
- 16 POSITION
- 17 CONSOLE OVERVIEW
- 18 AVAILABLE OPTIONAL ACCESSORIES
- 19 BLOCK DIAGRAM
- 20 AUDIO CONNECTIONS
- 23 FACTORY PRESET CONSOLE CONFIGURATION
- 24 INSTALLATION
- 24 INPUTS
- 25 MONO MODULE
- 25 INTRODUCTION
- 26 SETTINGS
- 27 PANEL
- 27 SWITCH
- 28 CONTROL
- 28 EQUALISER
- 29 SWITCHES
- 29 BUTTON
- 29 FADER
- 30 STEREO MODULE
- 30 INTRODUCTION
- 31 INTERFACE
- 31 INTERFACE PIN-OUT
- 31 INTERFACE DESCRIPTION
- 32 INTERFACE
- 32 ‘SSIR’ INTERFACE PIN-OUT
- 33 INTERFACE CONFIGURATION
- 33 INTERFACE DESCRIPTION
- 34 SETTING
- 35 PANEL
- 35 SWITCH
- 35 CONTROL
- 36 EQUALISER
- 36 BALANCE
- 36 SWITCHES
- 37 BUTTON
- 37 FADER
- 38 TELCO MODULE
- 38 INTRODUCTION
- 39 CONNECTION
- 39 REMOTE INTERFACE PIN-OUT
- 39 DESCRIPTION
- 40 CONNECTIONS
- 40 CONTROL
- 42 SWITCHES
- 42 BUTTON
- 43 FADER
- 44 TELEPHONE MODULE
- 44 INTRODUCTION
- 45 PANEL
- 45 CONNECTIONS
- 47 CONTROL
- 48 SWITCHES
- 48 BUTTON
- 49 FADER
- 50 MASTER - SUB MODULE
- 50 INTRODUCTION
- 51 PANEL
- 51 SWITCHERS
- 52 SECTION
- 52 SWITCH
- 52 BUTTON
- 53 FADER
- 54 MONITOR MODULE
- 54 INTRODUCTION
- 55 SETTINGS
- 56 CONNECTIONS
- 56 CONTROL
- 57 SECTION
- 59 MICROPHONE
- 60 PLUGS
- 61 POWER SUPPLY
- 61 DESCRIPTION
- 62 RELAYS
- 62 CONNECTION
- 63 SETTINGS
- 63 TROUBLESHOOTING
- 65 METERBRIDGE
- 65 DESCRIPTION
- 65 SETTING
- 67 TECHNICAL SPECIFICATIONS
- 68 DIMENSIONS
- 69 APPENDIX A: HOW TO REPLACE AN OXYGEN 4 CHANNEL MODULE
- 73 WARRANTY