advertisement
ApplianceLinc Owner’s Manual
ADVANCED FEATURES
Enabling/Disabling Load Sensing
Load Sensing allows you to manually turn on the load plugged into ApplianceLinc by using the switch on the load itself, without sending a command from an INSTEON or X10 controller. When the load is in the off state (with Load Sensing enabled), ApplianceLinc will “sense” that you are trying to turn it on with its built-in switch. When ApplianceLinc senses this, it will turn on the load automatically.
CAUTION: With Load Sensing, some lamps have been known to turn on ApplianceLinc after you have turned it off. Please use this feature with caution.
By default, Load Sensing is disabled on product versions 2.0 or higher and enabled on product versions
1.4 or higher.
Enable Load Sensing
1) Press & hold the Set button on ApplianceLinc for 3 seconds
The ApplianceLinc Status LED will begin blinking
2) Triple-tap the Set button on ApplianceLinc
The ApplianceLinc Status LED will stop blinking and turn on solid
3) Test that Load Sensing has been enabled by turning the load on and off from its built-in switch
The load will turn on and off
Disable Load Sensing
1) Press & hold the Set button on ApplianceLinc for 3 seconds
The ApplianceLinc Status LED will begin blinking
2) Double-tap the Set button on ApplianceLinc
The ApplianceLinc Status LED will stop blinking and turn on solid
3) Test that Load Sensing has been disabled by turning the load on and off from its built-in switch
The load will not respond
Restoring Power to ApplianceLinc
ApplianceLinc stores all of its settings, such as Links to other INSTEON devices, with non-volatile memory. Because settings are saved in this non-volatile memory, they will not be lost in the event of a power failure.
In the event of a power loss ApplianceLinc will automatically default the load to off when power is restored.
Resetting ApplianceLinc to its Factory Default Settings
The factory reset procedure can be used to clear the ApplianceLinc memory of all INSTEON Links and
X10 addresses
1) If you are using a Controller to control ApplianceLinc, be sure to Unlink it from the Controller. See
Unlinking ApplianceLinc from an INSTEON Controller.
2) Unplug ApplianceLinc for about 10 seconds
3) While holding down the Set button on ApplianceLinc, plug it back in, making sure not to let go of the
Set button
4) Continue to hold down the Set button for 3 seconds and then release
The ApplianceLinc Status LED will flash once and then turn off
After a few seconds, the Status LED and the load will turn on
Page 7 of 12
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 ABOUT APPLIANCELINC
- 3 Key ApplianceLinc Features
- 3 What is Included with ApplianceLinc
- 4 WHAT IS INSTEON?
- 4 INSTALLATION
- 4 Preparing to Install ApplianceLinc
- 5 Installing ApplianceLinc
- 6 CONTROLLING APPLIANCELINC FROM AN INSTEON CONTROLLER
- 6 Linking an INSTEON Controller to ApplianceLinc
- 6 Unlinking ApplianceLinc from an INSTEON Controller
- 6 CREATING INSTEON SCENES
- 7 ADVANCED FEATURES
- 7 Enabling/Disabling Load Sensing
- 7 Restoring Power to ApplianceLinc
- 7 Resetting ApplianceLinc to its Factory Default Settings
- 8 X10 PROGRAMMING OPTIONS
- 8 Setting the X10 Primary Address
- 8 Removing the X10 Primary Address
- 9 ADVANCED X10 PROGRAMMING OPTIONS
- 9 Remotely Setting an X10 Scene Address
- 9 Remotely Removing an X10 Scene Address
- 10 ABOUT INSTEON
- 10 Using Dual-Band INSTEON Devices to Upgrade Your Network
- 10 Important Note about INSTEON Networks; Split Single-Phase vs. 3-Phase Installation
- 10 Further Enhancing Reliability
- 10 ADDITIONAL RESOURCES
- 11 TROUBLESHOOTING
- 12 SPECIFICATIONS, CERTIFICATION, AND WARRANTY
- 12 Specifications
- 12 Certification
- 12 Limited Warranty
- 12 Limitations
- 12 INSTEON Technology Patent