Water trough. Miele KM 411

Add to My manuals
20 Pages


Water trough. Miele KM 411 | Manualzz

Cleaning and care

Water trough

^ Let the water cool to a safe temperature to prevent burns.

^ Place a container of a suitable size (a metal pot for example) under the drain valve. Slowly open the drain valve, f, by turning it counterclockwise, a.

^ Close the valve after all the water has drained by turning the valve clockwise, b, until the valve can turn no further (do not over-tighten or jam the valve).

^ Remove or wipe clean any residues remaining in the reservoir. The heating element can be raised to make this easier.

^ Fill the water trough with a mild solution of liquid dish soap and warm water, and rinse it out thoroughly.

^ Drain off the solution, rinse with clean warm water and dry.

Do not use stainless steel conditioner on the water trough.

Make sure that the underside of the grill is left accessible for draining the water. Wait until the water has cooled down before draining to prevent scalds.


Frequently asked questions

All repairs should be performed by a trained technician in strict accordance with national and local codes.

Any repairs or maintenance performed by unqualified personnel could be dangerous.

What if...

... the cooktop does not heat up when turned on?

Check whether:

– the overheating protection has been activated. Add water to the trough.

Refer to section "Overheating protection".

– the electrical circuit has blown a fuse or "tripped" the circuit breaker.

If power cannot be restored, it may be necessary to call either an electrician or the Miele Technical Service Dept.


All electrical work should be performed by a qualified electrician in accordance with local and national codes.



Disconnect the appliance from the main power supply before servicing.

To reduce the risk of electric shock, make sure that the appliance is properly grounded after installation.

Power supply:

Please check the data plate for

240 VAC, 60 Hz, 15A, or

208 VAC, 60 Hz, 15A and make sure your electrical supply matches the data plate.

Electrical connection




The appliance is provided with 3 leads;

L1 (black), L2 (red) and GND (green).

They must be connected to a dedicated line through the use of an approved junction box.

For further information, see the wiring diagram provided with the appliance.

Note to the installer:

Please leave these instructions with the consumer.


After sales service

In the event of a fault which you cannot correct yourself contact:

– Your Miele Dealer or

– The Miele Technical Service Department

USA 1-800-999-1360 [email protected]

CDN 1-800-565-6435 [email protected]

When contacting the Technical Service Department, please quote the model and serial number of your appliance. These are shown on the data plate.

Adhere data plate sticker below



Alteration rights reserved

This paper is made from cellulose bleached without the use of chlorine.



Key Features

  • Powerful heating element for quick and even cooking
  • Adjustable temperature control for grilling a variety of foods
  • Large grilling surface for cooking for a crowd
  • Nonstick coating for easy cleanup
  • Water trough to reduce smoke and flare-ups
  • Overheating protection for safety
  • Safety cut-out feature for added peace of mind

Related manuals

Frequently Answers and Questions

How do I clean the grill?
The grill should be cleaned after each use. To clean the grill, remove the lava rocks and water trough. Wash the lava rocks and water trough in hot soapy water. Wipe the grill grate with a damp cloth.
How do I replace the lava rocks?
The lava rocks should be replaced every 6 months or so. To replace the lava rocks, remove the old lava rocks and replace them with new lava rocks. Make sure that the new lava rocks are the same size as the old lava rocks.
How do I adjust the temperature of the grill?
The temperature of the grill can be adjusted by turning the temperature control knob. The temperature control knob is located on the front of the grill. Turn the knob to the desired temperature setting.