14DLV75 14-inch LCD TV/DVD COMBINATION SERVICE MANUAL

Add to my manuals
71 Pages

advertisement

14DLV75 14-inch LCD TV/DVD COMBINATION SERVICE MANUAL | Manualzz

Introduction

IMPORTANT SAFEGUARDS

(continued)

13. LIGHTNING

To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges. However, if there is thunder or lightning now, do not touch the unit and any connected cable.

This will for you not to receive the electric shock by the serge of thunder.

14. POWER LINES

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall onto or against such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal.

15. OVERLOADING

Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.

16. OBJECT AND LIQUID ENTRY

Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.

17. OUTDOOR ANTENNA GROUNDING

If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the

National Electrical Code (NEC), ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

EXAMPLE OF ANTENNA GROUNDING AS PER THE

NATIONAL ELECTRICAL CODE

ANTENNA LEAD IN WIRE

4

GROUND CLAMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRIC SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC-NATIONAL ELECTRICAL CODE

S2898A

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

18. SERVICING

Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

For example: a.

When the power-supply cord or plug is damaged.

b.

If liquid has been spilled, or objects have fallen into the unit.

c.

If the unit has been exposed to rain or water.

d.

If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation.

e.

If the unit has been dropped or the cabinet has been damaged.

f.

When the unit exhibits a distinct change in performance, this indicates a need for service.

Introduction

Precautions

6

Notes on handling

Do not shock the LCD panel. It may cause unit damage and malfunction.

When shipping the unit, the original shipping carton and packing materials come in handy. For maximum protection, repack the unit as it was originally packed at the factory.

■ Do not use volatile liquids, such as insect spray, near the unit. Do not leave rubber or plastic products to contact the unit for prolonged period. They will leave marks on the finish.

The top and rear panels of the unit may become warm after a long period of use. This is not a malfunction.

When the unit is not in use, be sure to remove the disc and turn off the power.

If you do not use the unit for a long period, the unit may not function properly in the future. Turn on and use the unit occasionally.

Notes on locating

Place the unit on a level surface. Do not use it on a shaky or unstable surface such as a wobbling table or inclined stand. The loaded disc may become disaligned and damage the unit.

■ When you place this unit near a TV, radio, or VCR, the playback picture may become poor and the sound may be distorted. In this case, place the unit away from the TV, radio, or VCR.

To avoid damage to this product, never place or store the unit in direct sunlight; hot, humid areas; or areas subject to excessive dust or vibration.

Notes on cleaning

Use a soft, dry cloth for cleaning.

Do not use any type of solvent, such as thinner and benzine, as they may damage the surface of the unit.

If you use a chemical saturated cloth to clean the unit, follow that product’s instructions.

Notes on LCD

The color LCD is manufactured using extremely high precision technology, but even so may include certain pixels that do not operate properly (that do not light, that remain lit constantly, etc.). We do our best to keep the number of these defective pixels to a minimum, but please understand that they cannot be completely eliminated even with the most advanced manufacturing technologies available today.

The fluorescent tube which illuminates the panel from the inside will deteriorate with use. When the LCD becomes dim, flickers, or does not illuminate, contact your dealer for replacement.

The brightness of the LCD monitor differs slightly depending on the viewing angles. Adjust the angle to obtain the best viewing. (The recommended angle is

90 degrees to the monitor.)

Notes on moisture condensation

Moisture condensation damages the unit. Please read the following carefully.

Moisture condensation occurs, for example, when you pour a cold drink into a glass on a warm day. Drops of water form on the outside of the glass. In the same way, moisture may condense on the optical pick-up lens inside this unit, one of the most crucial internal parts of the unit.

Exam ple of moisture condensation!

Optical pick-up lens

Moisture condensation occurs during the following cases.

When you bring the unit directly from a cold place to a warm place.

When you use the unit in a room where you just turned on the heater, or a place where the cold wind from the air conditioner directly hits the unit.

In summer, when you use the unit in a hot and humid place just after you move the unit from an air conditioned room.

When you use the unit in a humid place.

Do not use the unit when moisture condensation may occur.

If you use the unit in such a situation, it may damage discs and internal parts. Remove the disc, connect the power cord of the unit to the wall outlet, turn on the unit, and leave it for two or three hours. After two or three hours, the unit will have warmed up and evaporated any moisture. Keep the unit connected to the wall outlet and moisture condensation will seldom occur.

Wa it!

Wall outlet

19. REPLACEMENT PARTS

When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock or other hazards.

20. SAFETY CHECK

Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition.

21. HEAT

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

22. DISC SLOT

Keep your fingers well clear of the disc slot as it is closing. It may cause serious personal injury.

23. CONNECTING

When you connect the product to other equipment, turn off the power and unplug all of the equipment from the wall outlet. Failure to do so may cause a product damage. Read the owner's manual of the other equipment carefully and follow the instructions when making any connections.

24. HEADPHONES

When you use the headphones, keep the volume at a moderate level. If you use the headphones continuously with high volume sound, it may cause hearing damage.

25. LASER BEAM

Do not look into the opening of the disc slot or ventilation opening of the product to see the source of the laser beam. It may cause sight damage.

26. DISC

Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal injury and product malfunction.

27. LCD

Do not press hard or jolt the LCD panel. It may cause the LCD panel glass to break and injury may occur.

Should the LCD panel be broken and liquid leaks out, do not inhale or swallow it. Doing so may cause poisoning. If you have got it into your mouth, wash it out and consult your doctor. If your hands or clothes have touched it, wipe them with alcohol and a cleaning cloth and then wash them well.

28. NOTE TO CABLE TV SYSTEM INSTALLER

This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

ON DISPOSAL

This product contains mercury. Disposal of mercury may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industrial Alliance : www.eiae.org.

Notes on discs

On handling discs

Do not touch the playback side of the disc.

For example, handle the disc so that it is shown in figure below.

DO

Structure of disc contents

Normally, DVD video discs are divided into titles, and the titles are sub-divided into chapters. Video CDs and

Audio CDs are divided into tracks.

DVD video disc

Title 1

Chapter 1 Chapter 2

DVD video disc

Chapter 1

Title 2

Chapter 2 Chapter 3

Do not attach paper or tape to discs.

DO NOT

Playback side

Video CD/Audio CD

Video CD/Audio CD

Track 1 Track 2 Track 3 Track 4 Track 5

On cleaning discs

Fingerprints and dust on the disc cause picture and sound deterioration. Wipe the disc from the center outwards with a soft cloth. Always keep the disc clean.

DO DO NOT

Do not use any type of solvent such as thinner, benzine, commercially available cleaners or antistatic spray for vinyl LPs. It may damage the disc.

On storing discs

Do not store discs in a place subject to direct sunlight or near heat sources.

Do not store discs in places subject to moisture and dust such as a bathroom or near a humidifier.

Store discs vertically in a case. Stacking or placing objects on discs outside of their case may cause warping.

Each title, chapter or track is assigned a number, which is called “title number”, “chapter number” or “track number” respectively.

There may be discs that do not have these numbers.

Notes on copyright

The unauthorized recording, use, distribution, or revision of copyrighted materials including, without limitation, television programs, videotapes, and DVDs, is prohibited under the Copyright Laws of the United

States and other countries, and may subject you to civil and criminal liability.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by

Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by

Macrovision. Reverse engineering or disassembly is prohibited.

5

7

Introduction

8

Notes on discs (continued)

About this owner’s manual

This owner’s manual explains the basic instructions of this unit. Some DVD video discs are produced in a manner that allows specific or limited operation during playback. As such, the unit may not respond to all operating commands. This is not a defect in the unit.

Refer to instruction notes of discs.

“ ” may appear on the TV screen during operation.

A “ ” means that the operation is not permitted by the unit or the disc.

For example, sometimes it is unable to stop the playback of copyright message of the disc when the

STOP (

) button is pressed. Alternatively, the “ ” may also indicate that the feature is not available for the disc.

Notes on region numbers

The region number of this unit is 1. If region numbers, which stand for their playable area, are printed on your

DVD video disc and you do not find

1

or

ALL

, disc playback will not be allowed by the player. (In this case, the unit will display a message on-screen.)

Some DVDs that have no region code label may still be subject to area restrictions and therefore not playable.

On Video CDs

This DVD supports Video CDs equipped with the PBC

(Version 2.0) function. (PBC is the abbreviation of

Playback Control.) You can enjoy two playback variations depending on types of discs.

• Video CD not equipped with PBC function

(Version 1.1)

Sound and movie can be played on this DVD in the same way as an audio CD.

• Video CD equipped with PBC function

(Version 2.0)

In addition to operation of a Video CD not equipped with the PBC function, you can enjoy playback of interactive software with search function by using the menu displayed on the TV screen (Menu Playback).

Some of the functions described in this owner’s manual may not work with some discs.

Playable discs

This unit can play the following discs.

Disc Mark Contents

Disc

Size

Maximum playback time

Approx. 4 hours

(single sided disc)

12 cm

DVD video discs

Audio

+

Video

(moving pictures)

Approx. 8 hours

(double sided disc)

Approx. 80 minutes

(single sided disc)

8 cm

Approx. 160 minutes

(double sided disc)

Video

CDs

DIGITAL VIDEO

Audio

+

Video

(moving pictures)

12 cm

Approx. 74 minutes

8 cm Approx. 20 minutes

12 cm

Approx. 74 minutes

Audio

CDs

Audio

8 cm

(CD single)

Approx. 20 minutes

The following discs are also available.

DVD-R/RW discs of DVD video format

CD-R/CD-RW discs of CD-DA, Video CD, MP3, WMA or JPEG format

Kodak Picture CD and FUJICOLOR CD format

Some of these discs may be incompatible.

When you play an 8 cm disc, you need the adapter

(not supplied).

You cannot play discs other than those listed above.

You cannot play discs of DVD-RAM, DVD-ROM, Photo

CD, etc., or non standardized discs even if they may be labeled as above.

Some CD-R/RWs cannot be played back depending on the recording conditions.

This unit uses the NTSC color system, and cannot play DVD video discs recorded in any other color system (PAL, SECAM, etc.).

Because of problems and errors that can occur during the creation of DVD software and/or the manufacture of DVD discs, Toshiba cannot guarantee that the DVD player contained in the unit will play every feature of every DVD bearing the DVD logo. As one of the creators of DVD technology, Toshiba DVD players are manufactured using the highest standards of quality, and as a result, such incompatibilities are rare. If you happen to experience any difficulty playing a DVD in this unit, please feel free to call our Call Center (see page 53).

Introduction

Identification of controls

See the page in for details.

Top

Contents

Introduction

IMPORTANT SAFEGUARDS ............................ 2

Precautions ....................................................... 6

Notes on discs ................................................... 7

Contents ............................................................ 9

Identification of controls .................................. 10

Connections

Antenna connections ....................................... 14

Cable TV connections ..................................... 15

Connecting to optional equipment ................... 16

Power source .................................................. 20

Basic setup

Setting the language ....................................... 21

To memorize channels .................................... 22

TV operation

TV operation .................................................... 23

Closed captions ............................................... 25

Setting the V-Chip ........................................... 26

Picture control adjustment ............................... 28

Adjusting the picture preference ..................... 28

Selecting the color temperature ...................... 29

Sound control adjustment ............................... 30

Stereo and Second Audio Program (SAP) ...... 30

Basic playback

Playing a disc .................................................. 31

Advanced playback

Zooming ......................................................... 34

Locating desired scene .................................. 34

Repeat playback ............................................ 35

A-B Repeat playback ..................................... 35

Program playback .......................................... 36

Random playback .......................................... 36

Changing angles ............................................ 37

Title selection ................................................. 37

DVD menu ...................................................... 37

Changing soundtrack language ..................... 38

Subtitles ......................................................... 38

Karaoke playback ........................................... 39

Disc status ...................................................... 39

To turn off the PBC ........................................ 39

MP3/WMA/JPEG CD operation ..................... 40

Function setup

Customizing the function settings .................. 43

Temporary disabling of rating level by DVD disc ................................................... 46

Others

Language code list ......................................... 47

Troubleshooting ............................................. 48

Reception disturbances .................................. 50

Specifications ................................................. 51

Limited United States Warranty ..................... 52

Front

POWER button

21

EJECT ( ) button

32

VOLUME ( ) buttons

23

CHANNEL (

4

/

3

) buttons

22

SKIP ( / ) buttons

STOP( ) button

31

33

PLAY ( ) button

31

Side

PHONES jack

VIDEO IN/AUDIO IN

(L/R) (LINE 2 IN) jacks

Left Side Right Side

Adjusting the angle of the base

Approx. 15

Approx. 5

Disc slot

You can adjust the angle of the

TV-screen for 5° forward or for 15° backward from vertical angle.

Hold the base of the

TV while adjusting the angle.

Rear

9

10

POWER indicator

Remote sensor

COAXIAL DIGITAL AUDIO OUT jack

Antenna jack

DC input jack

COMPONENT VIDEO IN

(Y, P

B

/C

B

, P

R

/C

R

) jacks

S-VIDEO (LINE 1 IN) jack

VIDEO IN/AUDIO IN (L/R) (LINE 1 IN) jacks

11

Introduction

Identification of controls (continued)

Remote control

The instructions in this manual describe the function on the remote control. See the page in for details.

EJECT button

32

TV/DVD button

31

Direct channel selection buttons (0-9)

23

Numbered buttons (0-9)

26

RECALL button

24

JUMP button

34

INPUT SELECT button

16

PLAY MODE button

35

GAME button

16

TOP MENU button

37

MENU button

21

SETUP button

43

PLAY button

31

STOP button

31

SKIP buttons

33

REV button

33

FWD button

33

SLOW buttons

33

ANGLE button

37

AUDIO button

30

POWER button

21

SLEEP button

24

CH RTN button

24

ZOOM button

34

MUTE button

24

VOL +/– buttons

23

CANCEL button

26

*DVD MENU button

37

Direction buttons ( / / / )

21

CH +/– buttons

22

ENTER button

21

RETURN button

43

PAUSE button

32

CLOSED CAPTION button

REPEAT A-B button

35

25

SUBTITLE button

38

12

*DVD MENU button

Use the DVD MENU button to display the menu included on many DVD video discs.

To operate a menu, follow the instructions in “DVD menu.”

37

Connections

Antenna connections

If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna system. If you are using a cable TV service (CABLE), see page 15 for Cable TV connections.

Combination VHF/UHF antenna (Single 75 ohm cable or 300 ohm twin-lead wire)

Antenna jack

Antenna jack

75 ohm coaxial cable

(not supplied)

300-75 ohm matching transformer (supplied)

Connect the 75 ohm cable from the combination

VHF/UHF antenna to the antenna jack on the back of the TV/DVD.

If your combination VHF/UHF antenna has a 300 ohm twin-lead wire, use the 300-75 ohm matching transformer.

Combination VHF/UHF antenna (Separate VHF and UHF 300 ohm twin-lead wires)

Antenna jack

300-75 ohm matching transformer (supplied)

Connect the UHF 300 ohm twin-lead wire to the combiner (not supplied). Connect the VHF 300 ohm twin-lead wire to the 300-75 ohm matching transformer. Attach the transformer to the combiner, then attach the combiner to the antenna jack on the back of the TV/DVD.

Combiner

(not supplied)

UHF 300 ohm twin-lead wire

(not supplied)

VHF 300 ohm twin-lead wire

(not supplied)

14

Separate VHF/UHF antennas (75 ohm VHF cable and 300 ohm UHF twin-lead wires)

Antenna jack

Connect the VHF 75 ohm cable and UHF 300 ohm twin-lead wire to the combiner (not supplied).

Attach the combiner to the antenna jack on the back of the TV/DVD.

VHF 75 ohm

(not supplied)

Combiner

(not supplied)

UHF 300 ohm twin-lead wire

(not supplied)

Inserting batteries

1

Open the battery compartment cover in the direction of the arrow.

2

Install two “R03/AAA” batteries

(supplied), paying attention to the polarity indicated in the battery compartment.

3

Replace the compartment cover.

Operation

• Aim the remote control at the remote sensor and press control buttons to operate.

• Operate the remote control within 30° angle on either side of the remote sensor, up to a distance of approx. 5 meters.

Approx. 5 meters

Caution:

• Never throw batteries into a fire.

Notes:

• Be sure to use AAA size batteries.

• Dispose of batteries in a designated disposal area.

• Attention should be drawn to the environmental aspects of battery disposal.

• Do not mix different battery types or combine used batteries with new ones.

• If the remote control does not operate correctly, or if the operating range becomes reduced, replace both batteries with new ones.

• If the batteries are dead or if you will not be using the remote control for a long time, remove the batteries to prevent battery acid from leaking into the battery compartment.

13

Cable TV connections

This TV/DVD has an extended tuning range and can tune most cable channels without using a Cable TV converter box.

Some cable companies offer “premium pay channels” in which the signal is scrambled. Descrambling these signals for normal viewing requires the use of a descrambler device which is generally provided by the cable company.

For subscribers to basic cable TV service

Antenna jack

For basic cable service not requiring a converter/descrambler box, connect the Cable TV 75 ohm coaxial cable directly to the

Antenna jack on the back of the TV/DVD.

75 ohm coaxial cable

For subscribers to scrambled cable TV service

If you subscribe to a cable TV service which requires the use of a converter/descrambler box, connect the incoming 75 ohm coaxial cable to the converter/descrambler box. Using another 75 ohm coaxial cable, connect the output jack of the converter/descrambler box to the antenna jack on the TV/DVD. Follow the connections shown below. Set the TV/DVD to the output channel of the converter/descrambler box (usually channel 3 or 4) and use the converter/descrambler box to select channels.

Incoming

75 ohm

Cable TV

Converter/ descrambler

75 ohm cable to

TV/DVD

Antenna jack

For subscribers to unscrambled basic cable TV service with scrambled premium channels

If you subscribe to a cable TV service in which basic channels are unscrambled and premium channels require the use of a converter/descrambler box, you may wish to use a signal splitter and an A/B Switch box (available from the cable company or an electronics supply store). Follow the connections shown below. With the switch in the “B” position, you can directly tune any nonscrambled channels on your TV/DVD. With the switch in the “A” position, tune your TV/DVD to the output of the converter/descrambler box (usually channel 3 or 4) and use the converter/ descrambler box to tune scrambled channels.

Incoming

75 ohm

Cable TV

Splitter

Converter/ descrambler

A/B switch

A

B

75 ohm cable to TV/DVD

Antenna jack

15

Connections

Connecting to optional equipment

You can enjoy VCR, camcorder or TV game with connection to external input.

INPUT SELECT

GAME

Using the audio/video inputs

Press INPUT SELECT repeatedly to select the desired mode.

“LINE1”, “LINE2”, “GAME”, “COMPONENT” or TV channel will display on the screen for 4 seconds.

TV Channel LINE 1

(Rear lower left)

LINE 2

(Left side)

LINE 1

COMPONENT GAME (LINE 2 IN)

Note: In the DVD mode this key will not operate.

Connecting to a VCR

To playback from the VCR, connect the VCR to the TV/DVD as shown.

Select the “LINE2” by pressing INPUT SELECT repeatedly.

: Signal flow

VCR

(red)

(white)

(yellow)

To Audio/Video OUT

Left side (LINE 2 IN)

The LINE 1 IN terminals can be used in the same way.

To AUDIO(L/R)/VIDEO IN

Audio/Video cable (not supplied)

Note: Picture might be muted for some VCR playback. This is not a malfunction of this unit.

Connecting to a camcorder

To playback from the camcorder, connect the camcorder to the TV/DVD as shown.

Select the “LINE2” by pressing INPUT SELECT repeatedly.

Left side (LINE 2 IN)

: Signal flow

Camcorder

(red)

To Audio/Video OUT

(white)

(yellow)

The LINE 1 IN terminals can be used in the same way.

Audio/Video cable (not supplied)

To AUDIO(L/R)/VIDEO IN

Connecting to a TV Game

You can enjoy playing a TV game on the screen by adjusting to suitable brightness for your eyes.

1. Connect a TV Game to the TV/DVD.

2. Select the “GAME” by pressing INPUT SELECT repeatedly or simply press GAME.

The GAME mode screen appears.

• This TV/DVD has the GAME mode function (see page 24).

Left side (LINE 2 IN)

: Signal flow

(red)

To Audio/Video OUT

(white)

(yellow)

Only the LINE 2 IN terminals can be used with the

GAME mode.

Audio/Video cable (not supplied)

To AUDIO(L/R)/VIDEO IN

Notes:

• You can also change the TV screen to the desired mode by pressing the CH +/– buttons.

• The TV/DVD can also be used as a display device for many video games. However, due to the wide variety of different types of signal generated by these devices and subsequent hook-up variations required, they have not all been included in the suggested connection diagrams. You'll need to consult each component's Owner's Manual for additional information.

• Interactive video games that involve shooting a “gun” type of joystick at on-screen target may not work on this TV/DVD.

16

Connections

Connecting to optional equipment (continued)

You can enjoy high quality dynamic sounds by connecting the

TV/DVD to optional audio equipment.

* This section uses the following reference mark.

: Front speaker

: Rear speaker

: Sub woofer

: Center speaker

: Signal flow

Connecting to an amplifier equipped with a Dolby Digital decoder

Dolby Digital

Dolby Digital is the surround sound technology used in theaters showing the latest movies, and is now available to reproduce this realistic effect in the home. You can enjoy motion picture and live concert DVD video discs encoded via the

Dolby Digital recording system with this dynamic realistic sound by connecting the TV/DVD to a 6 channel amplifier equipped with a Dolby Digital decoder or Dolby Digital processor. If you have a Dolby Surround Pro Logic decoder, you will obtain the full benefit of Pro Logic from the same DVD movies that provide full 5.1-channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark.

Rear lower right of the TV

Amplifier equipped with a

Dolby Digital decoder

To COAXIAL type digital audio input

To COAXIAL DIGITAL

AUDIO OUT

75

coaxial cable (not supplied)

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories.

Connecting to an amplifier equipped with a Dolby Surround Pro Logic

*

Dolby Surround Pro Logic

You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by connecting an amplifier and speaker system (right and left front speakers, a center speaker, and one or two rear speakers).

With an amplifier equipped with a Dolby Digital

Connect the equipment the same way as described in “Connecting to an amplifier equipped with a Dolby Digital decoder.”

Refer to that amplifier’s owner’s manual and set the amplifier so you can enjoy Dolby Surround Pro Logic sound.

With an amplifier not equipped with a Dolby Digital

Connect the equipment as follows.

• This connection is only suitable for Video CDs and Audio CDs.

Rear lower right of the TV

Amplifier equipped with a

Dolby Surround Pro Logic

To COAXIAL type digital audio input

To COAXIAL DIGITAL

AUDIO OUT

75

coaxial cable (not supplied)

* Connect one or two rear speakers. The output sound from the rear speakers will be monaural even if you connect two rear speakers.

Connecting to an amplifier equipped with a DTS decoder

Digital Theater Systems (DTS)

DTS is a high quality surround technology used in theaters and now available for home use, on DVD video discs or audio CDs.

If you have a DTS decoder or processor, you can obtain the full benefit of 5.1 channel DTS encoded sound tracks on DVD video discs or audio CDs.

Rear lower right of the TV

Amplifier equipped with a DTS decoder

To COAXIAL type digital audio input

To COAXIAL DIGITAL

AUDIO OUT

75

coaxial cable (not supplied)

“DTS” and “DTS Digital Out” are trademarks of Digital

Theater Systems, Inc.

18

Connecting to an optional equipment with S-video output

If you connect a VCR with an S-VIDEO cable to the S-VIDEO IN jack on the rear lower left of the TV/DVD, you must also connect the audio cables to the AUDIO IN jacks on the rear lower left of the TV/DVD (LINE 1 IN). The

S-VIDEO cable only carries the video signal. The audio signal is separate.

Select the “LINE1” by pressing INPUT SELECT repeatedly.

Ex. VCR with S-Video

Rear lower left of the TV

: Signal flow

(playback)

To S-VIDEO IN

To S-VIDEO OUT

To AUDIO (L/R) IN

To Audio (L/R) OUT

Audio cable (not supplied)

S-Video cable (not supplied)

Note: When the S-VIDEO cable and the standard video cable are connected at the same time, the S-video cable takes precedence.

Connecting an optional equipment with ColorStream ® (Component video) output

Your TV/DVD is capable of using ColorStream ® (component video). Connecting your TV/DVD to a component video compatible DVD player, such as a Toshiba DVD player with ColorStream ® can greatly enhance picture quality and performance.

Ex. DVD player with Component video

: Signal flow

Rear lower left of the TV

To Component

Video OUT

To AUDIO (L/R) IN

To Audio OUT

Audio cable (not supplied)

Component video cable (not supplied)

Selecting Component input mode

Press INPUT SELECT repeatedly to select “COMPONENT” mode.

COMPONENT

When using the Component video cable, an Audio cable must be connected to

AUDIO IN (L/R) (LINE 1 IN) jacks.

To COMPONENT

(Y, P

B

/C

B

, P

R

/C

R

) IN

The ColorStream ® inputs on this unit are for use with devices that output 480i interlaced signals and 480p progressive signals. This unit will not accept or display 720p progressive scan signals or 1080i interlaced high-definition signals. If you connect a highdefinition set-top receiver, 720p progressive scan DVD player, or other similar device to the unit’s ColorStream ® inputs, YOU MUST

SWITCH THE DEVICE’S OUTPUT TO 480i INTERLACED OR 480p PROGRESSIVE MODE FIRST. Failure to do this will cause a poor or no picture to display.

Notes:

Refer to the owner’s manual of the connected equipment as well.

When you connect the unit to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connections.

If you place the unit near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the unit away from the tuner and radio.

17

Connecting to an amplifier equipped with an MPEG audio decoder

MPEG2 sound

You can enjoy motion picture and live concert DVD video discs encoded via the MPEG2 recording system with dynamic realistic sound by connecting an amplifier equipped with an MPEG2 audio decoder or MPEG2 audio processor.

Rear lower right of the TV

Amplifier equipped with an

MPEG2 audio decoder

To COAXIAL type digital audio input

To COAXIAL DIGITAL

AUDIO OUT

75

coaxial cable (not supplied)

Connecting to an amplifier equipped with a digital audio input

2 channel digital stereo

You can enjoy the dynamic sound of 2 channel digital stereo by connecting an amplifier equipped with a digital audio input and speaker system (right and left front speakers).

Note: PCM audio is limited to DVD or CD playback.

Rear lower right of the TV

Amplifier equipped with a

Digital audio input

To COAXIAL type digital audio input

To COAXIAL DIGITAL

AUDIO OUT

75

coaxial cable (not supplied)

Notes:

• DO NOT connect the COAXIAL DIGITAL AUDIO OUT jack of the TV/DVD to the AC-3 RF input of a Dolby Digital Receiver.

This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the COAXIAL DIGITAL AUDIO

OUT jack of the TV/DVD.

• Connect the COAXIAL DIGITAL AUDIO OUT jack of the TV/DVD to the “COAXIAL” input of a Receiver or Processor.

• Refer to the owner’s manual of the connected equipment as well.

• When you connect the TV/DVD to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connections.

• The output sound of the TV/DVD has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening level. Otherwise, the speakers and your hearing may be damaged by a sudden high volume sound.

• Turn off the amplifier before you connect or disconnect the TV/DVD’s power cord. If you leave the amplifier power on, the speakers may be damaged.

19

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals