Contents. Korg Pa600QT, PA600 96 Pages
advertisement
Contents
1
Contents
Introduction
Welcome! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
About this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Making a safety copy of your data . . . . . . . . . . . . . . . . . . . . . . . . .5
Restoring the original factory data . . . . . . . . . . . . . . . . . . . . . . . . .5
Loading the Operating System . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Start up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Connecting the AC power cord . . . . . . . . . . . . . . . . . . . . . . . . . 17
Turning the instrument on (or setting it to standby) . . . . . . . 17
Controlling the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Headphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Loudspeakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Audio Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
MIDI connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Damper pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Assignable pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
The music stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Keyboard tracks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Sequencer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
The LOGO decoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Interface basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Color TouchView graphical user interface . . . . . . . . . . . . . . . . 21
Operative modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Selected, highlighted items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Non-available, grayed-out parameters . . . . . . . . . . . . . . . . . . . 23
Shortcuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Easy Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
The Style Play page in detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
The Song Play page in detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Quick Guide
Turning the instrument on . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Turning the instrument on and viewing the main screen . . . 28
Connecting and calibrating the Damper pedal . . . . . . . . 29
Programming the Damper pedal . . . . . . . . . . . . . . . . . . . . . . . . 29
Playing the Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Starting and stopping the Demo . . . . . . . . . . . . . . . . . . . . . . . . . 31
Playing Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Selecting a Sound and playing it on the keyboard . . . . . . . . . . 33
Playing two or three Sounds at the same time . . . . . . . . . . . . . 35
Playing different Sounds with your left and right hand . . . . . 37
Changing the split point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Raising or lowering the Upper octave . . . . . . . . . . . . . . . . . . . . 40
Selecting and saving Performances . . . . . . . . . . . . . . . . . . . 41
Selecting a Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Saving your settings to a Performance . . . . . . . . . . . . . . . . . . . . 42
Selecting and saving the “My Setting” Performance . . . 44
Selecting the startup parameters (the "My Setting"
Performance) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Saving the startup parameters into the "My Setting"
Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Selecting and playing Styles . . . . . . . . . . . . . . . . . . . . . . . . . 45
Selecting and playing a Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Intro, Variation, Fill, Break, Ending . . . . . . . . . . . . . . . . . . . . . . 48
Single Touch Settings (STS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Adjusting the balance between the Style and the keyboard . . 51
Adjusting the volume of the separate tracks . . . . . . . . . . . . . . . 51
Turning the Style tracks on/off . . . . . . . . . . . . . . . . . . . . . . . . . . 52
The Chord Sequencer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Song Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Selecting a Song to play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Playing back a Song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Changing the tracks’ volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Turning the Song tracks on/off . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Soloing a track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
The SongBook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Selecting the desired Entry from the Main List . . . . . . . . . . . . . 66
Displaying Artist or Genre . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Sorting Entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Searching for Entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Adding Entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Editing the Entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Creating a Custom List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Selecting and using a Custom List . . . . . . . . . . . . . . . . . . . . . . . 74
Recording a new Song (Standard MIDI File) . . . . . . . . . . . 75
Preparing the Style and Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Accessing the Backing Sequence (Quick Record) mode . . . . . 75
Setting the Record parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Second-take recording (Overdubbing) . . . . . . . . . . . . . . . . . . . 79
Saving a Song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Searching files and musical resources . . . . . . . . . . . . . . . . . 81
How to use the Search function . . . . . . . . . . . . . . . . . . . . . . . . . 81
Notes about searching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Appendix
Replacing the clock backup battery . . . . . . . . . . . . . . . . . . . 86
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
MIDI Implementation Chart . . . . . . . . . . . . . . . . . . . . . . . . . . 90
2
Contents
4
Welcome!
Welcome!
Welcome to the world of Korg Pa600 Professional Arranger!
Pa600 is one the most powerful arranger available today, both for professional and home entertainment use.
Here are some of the features of your new instrument:
Physical Features and User Experience
• 61 synth-type keys with velocity.
• Slim and compact, lightweight, elegant cabinet design.
• Wide TFT graphic touch screen display. Professional
TouchView™ graphic interface for direct access to the onscreen controls and to the musical resources.
• High-quality integrated amplification, and high-quality output (DAC) audio converters.
• RX (Real eXperience) Technology, the cutting edge engine that drives every aspect of the Pa600 – from the synthesis to the display and how it all works together.
• Two assignable switches, a joystick and an assignable pedal ensure total control for all the various levels of articulation of the sound.
• Quick access to Arabic Scale programming via the Quarter
Tone controls right on the front panel (Quarter Tone model
only).
Sounds and Effects
• Powerful sound generation system, for crystal-clear, realistic sounds.
• DNC (Dynamic Nuance Control) Sounds, more realistic and vivid than ever.
• 96 MB of Sample memory for User PCM Samples.
• 128 voices of polyphony.
• General MIDI Level 2 Sound-compatible. Enhanced Sound compatibility for GM Songs.
• More than 950 Sounds, plus 64 Drum Kits.
• 320 Performance locations, plus 4 Single Touch Settings
(STS) for each Style and SongBook entry, for fast setting of keyboard sounds and effects.
• Four Stereo Master FX, with 125 effect types. Mastering
Limiter and Final 4-band Parametric EQ.
Styles and Songs
• Over 360 Factory Styles with 4 Variations and 4 Fill In +
Break, plus 10 Favorite and 3 User Style banks for unlimited storage of your custom Styles and settings.
• Style and Pad Record, including the enhanced “Guitar
Mode 2” for even more realistic guitar parts.
• “Chord Sequencer” function to record on-the-fly any chord progression.
• Standard MIDI File player and recorder, and MP3 player with Vocal Remover.
• Lyrics, Score and Marker display. Enhanced compatibility with Lyrics in graphical format (+G) for Standard MIDI
Files and MP3 files.
• Full-featured 16-track sequencer.
• Fully editable SongBook music database, for fast song retrieving.
Other Features
• Search function, to instant retrieving of Songs and files.
• Operating System updates, to load new features and enhancements. Don’t let your instrument get old!
• Generous internal memory, to store the greatest amount of data.
• USB 2.0 High Speed Host port, for connecting external devices like hard disks, CD-ROM drives, USB memory sticks, etc.
• USB 2.0 High Speed Device port, to connect a personal computer to your Pa600. This port can be used for file transfer, and for MIDI connection (without the need of a dedicated MIDI interface for the personal computer).
Welcome!
What’s in the box
5
What’s in the box
After you buy your Pa600, please check that all the following items are included in the package. If any of the following items is missing, please contact your Korg dealer immediately.
• Pa600
• Music stand
• Power cable
• Quick Guide
• Accessory Disc (containing the Video Manual, the User
Manual, the USB driver)
About this manual
This manual is the Quick Guide, containing a series of practical guides. In addition, in the Accessory Disc and in our web site you will find the complete User Manual and a multilingual
Video Manual
, showing how to use your Pa600 in easy steps.
Contacts
Your preferred Korg dealer not only delivers this keyboard, but also a whole bunch of hardware and software accessories, as well as service information. You should ask them for any help should you eventually need.
Our international web site is www.korg.com
. Korg distributors around the world may have their own web page on the internet.
A list of all Korg Distributors can be found in our dedicated web site ( www.korg.co.jp/English/Distributors/ ).
Making a safety copy of your data
Making a safety copy
In case you like to customize your Musical Resources (Sounds,
Performances and Styles), we suggest you use the Media > Utility
> Backup Resources command to make frequent backup copies into compact archives.
Also, you can use the Media > Save All command to save files that you can separately reload one by one.
Restoring a safety copy
To restore a backup, use the Media > Utility > Restore Resources.
If you saved your data with the Media > Save All command, use the Media > Load operations to reload them.
Restoring the original factory data
In case you want to restore the original factory data, use the
Media > Utility > Factory Restore command.
Warning:
This operation will overwrite all the Factory, Local,
Favorite and User data!
Loading the Operating System
Your Pa600 can be constantly updated as new versions of the operating system are released by Korg. You can download the operating system from our web site ( www.korg.com
). Please, read the instructions supplied with the operating system on the site.
You can see which version of the operating systems is installed in your Pa600 by going to the Media > Utility page.
Warning:
Do not install an OS other than the official OS supplied by Korg for the Pa600. Trying to install an OS created for different models or downloaded from unofficial web sites may cause data loss and permanent damage to the instrument. Korg is not responsible for any damage caused by improper installation of the OS.
6
Overview
Front Panel
Overview
(Quarter Tone version only)
Front Panel
Speakers
The integrated speakers give a faithful reproduction of the sound of Pa600. They are automatically deactivated when inserting a jack into the PHONES connector. They can be manually deactivated with the “Speakers On/Off ” parameter you can find in the
Global > Audio & EQ > MP3/Speakers page.
Quarter Tone
The Quarter Tone / Sub Scale section is only available in the Pa600
Quarter Tone version.
QUARTER TONE / SUB SCALE
Use the mini-keyboard to modify the Quarter Tone Scale, and the four SC Preset buttons to select one of the preset scales. Keep one of the buttons pressed to memorize the current scale into the corresponding SC Preset.
Joystick lever
The joystick is on the left side of the front panel.
JOYSTICK
This joystick triggers different functions, depending on the direction it is moved towards.
Y+
Move the joystick towards the left (–) to lower the pitch, or towards the right (+) to raise it. This effect is called the
Pitch Bend.
Move the joystick forward to trigger Modulation
Overview
Front Panel
7
Y– Move the joystick backward, to trigger the function assigned in Sound mode.
Volume controls
Use these knobs to control the master volume, and to balance between the Keyboard and the Style or the Song.
MASTER VOLUME
This knob controls the overall volume of the instrument, both of the integrated speakers, the AUDIO OUT and the PHONES outputs. It also controls the volume of the AUDIO IN inputs in the final mix.
BALANCE
While in Style Play and Song Play mode, this knob usually balances the volume of the Keyboard tracks against the Style (ACC,
Accompaniment), Song (SNG) and Pad tracks. This is a relative control, whose effective maximum value is determined by the
MASTER VOLUME knob position.
When moved, a magnified version of a virtual slider appears in the display, for more accurate adjustment.
It can be programmed to work as the volume control for the
Accompaniment/Song tracks only, leaving the Keyboard tracks unchanged (in the Controllers > Hand Controllers page of the
Global mode).
Note:
This does not work in the Sequencer and Sound modes.
Assignable Switches
ASSIGNABLE SWITCH
Freely assignable switches, that can be programmed in the Pad/Assignable Switch >
Switch page of the Style Play or Song Play mode.
8
Overview
Front Panel
Mode selection
Each of these buttons recalls one of the instrument’s operating modes. When selected, each mode excludes all the others.
Songs, to let you experience the sonic power of the Pa600. To exit from this mode, press any of the MODE buttons.
Special Mode Buttons
These buttons are used to recall settings, file management and record modes.
STYLE PLAY
Style Play mode, where you can play Styles (eight tracks of automatic accompaniments) and play up to four Keyboard tracks and four Pad tracks. In the main page, Keyboard tracks are shown in the right half of the display.
You can recall the main page by pressing EXIT from any of the
Style Play edit pages. If you are in a different operating mode, press STYLE PLAY to recall the Style Play mode. If Keyboard tracks are not shown in the display, press the TRACK SELECT button until you can see them.
This operating mode is automatically selected when turning the instrument on. The “My Setting” Performance will be automatically selected.
SONG PLAY
Song Play mode, where you can play back Songs in Standard
MIDI File (SMF or KAR) or MP3 format. In addition to the Song tracks, you can play up to four Keyboard tracks and four Pads along with the Song(s). In the main page, Keyboard tracks are shown in the right half of the display.
You can recall the main page of this mode by pressing EXIT from any of the Song Play edit pages. If you are in a different operating mode, press SONG PLAY to recall the Song Play mode. Use the TRACK SELECT button to cycle between the
Keyboard and Song tracks.
SEQUENCER
Sequencer mode, where you can play, record or edit Songs (in Standard MIDI File format). The Backing Sequence mode lets you record a new Song based on the Keyboard and Style tracks, and save it as a new Standard MIDI File.
Note:
In this mode, you cannot play MP3 files.
SOUND EDIT
Sound Edit mode, to play single Sounds on the keyboard, or edit them.
User Sounds may be based on User PCM Samples to be loaded into the dedicated Sample RAM memory.
Note:
Pa600 cannot load compressed User PCM Samples from other Pa-Series models.
While in any other operating mode, keep the SHIFT button pressed and press this button, to send the selected Sound to the Sound Edit mode.
DEMO
Press the STYLE PLAY and SONG PLAY buttons together to select the Demo mode. This mode lets you listen to some Demo
GLOBAL
This button recalls the Global mode, where you can adjust various global settings. Most Global settings are automatically memorized as soon as you edit them. This mode overlaps any operating mode, that will still remain active in the background.
Press EXIT to go back to the underlying operating mode.
MEDIA
This button recalls the Media mode, where you can perform various operations on files and storage devices (Load, Save, Format, etc…). This mode overlaps any operating mode, that still remains active in the background. Press EXIT to go back to the underlying operating mode.
The internal memory contains both the internal data (“SYS
[KORG SYSTEM]” area) and a space where to save data (“DISK
[KORG DISK]” area).
RECORD
This button sets the instrument to the Record mode (which one depends on the current operating mode).
Accompaniment, Memory, Manual Bass,
Chord Sequencer
These buttons let you turn all Accompaniment tracks on/off, decide what should remain in memory, and how to play the bass.
In addition, they have the Chord Sequencer as a second function.
ACCOMP. (Accompaniment)
In Style Play and Sequencer-Backing Sequence mode, use this button to turn the Accompaniment tracks (ACC1 ~ ACC5) on or off.
On After pressing START/STOP, the full accompaniment plays and follows the detected chords.
Off No chords detected. After pressing START/STOP, only the Drum and Percussion accompaniment tracks can play.
You can jump to the Global > Mode Preferences > Style
Play page by keeping SHIFT pressed and pressing the ACCOMP button.
Overview
Front Panel
9
MEMORY
This button allows you to choose whether the Lower notes and/ or chord triggering the accompaniment must remain in memory after raising your hand from the keyboard.
On Depending on the setting of the “Memory Mode” parameter (in the Global > Mode Preferences >
Style Play), the sound on the left of the split point
(Lower), and/or the chords for the automatic accompaniment can kept in memory even when you raise your hand from the keyboard.
Off Both the sound and chord are released as soon as you raise your hand from the keyboard.
Note:
This function can be automatically activated by playing the keyboard harder, by setting the “Velocity Control” parameter (in the Global > Mode Preferences > Style Play page).
You can jump to the Global > Mode Preferences > Style
Play page by keeping SHIFT pressed and pressing the MEMORY button.
MAN. BASS (Manual Bass)
This button turns the Manual Bass function on or off.
On The automatic accompaniment stops playing
(except for the Drum and Percussion tracks), and you can manually play the Bass track on the
Lower part of the keyboard. You can start the automatic accompaniment again after pressing this button to turn off the Manual Bass function.
Off The bass track is automatically played by the Style.
Note:
When you press the MANUAL BASS button, the Bass track volume is automatically set to its maximum value. The volume is automatically set back to the original value when the MANUAL
BASS button is deactivated.
CHORD SEQUENCER (PLAY/STOP AND RECORD)
While a Style is in play, you can use this section as a Chord
Sequencer and record a looping sequence of chords. The chords will drive the arranger, leaving your hands free for solo playing.
RECORD (MEMORY + MAN. BASS):
Press these buttons together to start recording the Chord Sequence. Recording will start from the next measure. Press these buttons again to stop recording.
PLAY/STOP (ACCOMP. + MEMORY):
Press these buttons together to let the Chord Sequence play in loop, and automatically drive the arranger. The Chord Sequence will start on the next measure. Press these buttons again to stop the sequence.
The Chord Sequence will remain in memory up until you record a new Chord Sequence, or you turn the Pa600 off.
Pads
Here you can play (and stop) the Pads, i.e. single sounds or looping sequences.
PAD 1-4
STOP
Each Pad button corresponds to a dedicated Pad track. Use these buttons to trigger up to four sounds or sequences at the same time.
• Press a single PAD button to trigger a single sound or sequence.
• Press more PAD buttons to trigger several sounds or sequences.
The sequences will play up to the end. Then, they will stop or continue repeating, depending on their “One Shot/Loop” status
(see the “Pad Type” parameter in the Pad Record mode).
You can stop all sequences, or just some of them, by pressing the
STOP button of the PAD section:
• Press STOP to stop all sequences at once.
• Keep STOP pressed and press one (or more) of the PAD buttons to stop the corresponding sequence(s).
• Press one of the ENDING buttons to stop both the accompaniment and the Pads at the same time.
About Pad synchronization.
In Style Play mode, Pads are synchronized to the Style’s Tempo. In Song Play mode, they are synchronized to the Player.
Note:
There is no synchronization with MP3 files. Pads can only be synchronized to the Tempo of the latest selected Standard MIDI
Files. Therefore, when an MP3 file is assigned to the last select
Player, Pads will synchronize to the Tempo of the last Standard
MIDI File that has been played back.
About Pads and the Player’s Play command.
When you press the PLAY button to start the Player, all Pads will stop playing.
You can jump to the Style Play > Pad/Assignable Switch page by keeping SHIFT pressed and pressing one of the PAD buttons.
Selection
Here you can select a Style, Sound, SongBook entry, or Song, and activate the automatic selection of the STSs.
STS MODE
This button lets you cycle between the following functions.
On
Flashing
When a Style is selected, STS 1 is also automatically selected. The Keyboard sounds and effects will change, along with the Style sounds and effects.
Variation/STS Link function activated. This function makes each Variation recall the corresponding STS when selected. For example, select
Variation 2, and STS 2 will be automatically recalled; select Variation 3, and STS 3 will be automatically recalled.
10
Overview
Front Panel
Off When you select a Style, the Style sounds and effects will change. The Keyboard sounds and effects will not change.
STYLE
Use this button to open the Style Select window and select a
Style. This is the same as touching the name of the Style in the display. Repeatedly press it to cycle between the Style bank pages.
For each type of Styles there are several banks, that can be selected by touching the side tabs. Each Style bank contains various pages, each with up to eight Styles, that can be selected by touching the lower tabs.
Styles of the Factory type are usually write-protected (unless you uncheck the “Factory Style and Pad Protect” option in the Global
> Mode Preferences > Media page). Styles of the Favorite type can be used to load new Styles from an external device, or to save newly created or edited Styles into banks with a freely editable name. Styles of the User type are like the Favorites, but you cannot edit the bank name, and are better suited for temporary materials.
By keeping this button pressed for about one second, the
“Write Current Style Settings” dialog box will appear.
SOUND
Use this button to open the Sound Select window and select a
Sound to be assigned to the selected track. This is the same as touching a Sound name in the display. Repeatedly press it to cycle between the Sound bank pages.
For each type of Sounds there are several Sound banks, that can be selected by touching the side tabs. Each Sound bank contains various pages, each with up to eight Sounds, that can be selected by touching the lower tabs.
Sounds of the Factory type are usually write-protected (unless you uncheck the “Factory Sound Protect” option in the Global >
Mode Preferences > Media page). Sounds of the Legacy type are standard Factory Sounds allowing greater compatibility with older Pa-Series instruments. Factory Sounds of the GM type allow for compatibility with General MIDI sounds. Sounds of the User type are locations where you can load new Sounds from an external device, or save new or edited Sounds. The User DK type is where you can load new Drum Kits, or save new or edited
Drum Kits.
SONGBOOK
Press this button to open the SongBook (when you are in Style
Play or Song Play mode). While the SongBook is shown on the display, you can browse through the music database.
By keeping this button pressed for about one second, a new
SongBook Entry with the current settings is added to the database. You will be able to give it a name and save.
You can jump to the SongBook > Custom List page by keeping SHIFT pressed and pressing the SONGBOOK button.
SONG
Press this button to open the Song Select window and choose a
Songs. This is the same as touching the Song name in the display.
Style Elements
This section contains the separate elements of a Style (Intro,
Variation, etc.).
INTRO 1-3 buttons
These buttons turn the corresponding Intro on. After pressing one of these buttons, start the Style, and it will begin with the selected intro. The INTRO LED will automatically go off at the end of the intro.
At the end of the Intro, the Variation whose LED was blinking will be selected.
Press one of the INTRO buttons twice (LED blinking) to let the corresponding Intro play in loop, and select any other Style element (Intro, Variation, Ending) to exit the loop (or press the same button again).
Note:
Intro 1 plays a short sequence with different chords, while
Intro 2 plays on the latest recognized chord. Intro 3 is usually a one-bar Count In.
VARIATION 1-4 buttons
Each of these buttons selects one of the four Variations of the current Style. The higher the Variation number, the denser the arrangement.
When the STS MODE LED is flashing, the Variation/STS Link function is activated: when selected, each Variation recalls the corresponding STS.
You can jump to the Style Play > Drum/Fill page by keeping SHIFT pressed and pressing one of the VARIATION buttons.
AUTO FILL
This button allows to turn the Auto Fill function on or off.
On When selecting a different Variation, the Fill having the same number of the previous Variation is automatically selected. For example, if going from
Variation 2 to Variation 3, Fill 2 is automatically selected.
Off When choosing a Variation, no fill is selected.
BREAK
This button triggers a break. Press it twice (LED blinking) to let it play in loop. Press it again or select any other Style Element
(Intro, Variation, Ending) to exit from the loop.
ENDING 1-3 buttons
While the Style is running, these three buttons trigger an Ending, and stop the Style. Press one of them, and the Style will stop running with an Ending.
Press them twice (LED blinking) to let them play in loop, and select any other Style element (Intro, Variation…) to exit the loop (or press the same button again).
Note:
Ending 1 plays a short sequence with different chords, while
Ending 2 plays on the latest recognized chord. Ending 3 starts immediately, and is just two measures long.
Overview
Front Panel
11
Style Controls
Use these buttons to start/stop the accompaniment.
FADE IN/OUT
When a Style or Song is not playing, press this button to start it with the volume “fading in” (the volume goes from zero to the maximum).
When a Style or Song is playing back, press this button to stop it with the volume “fading out” (the volume gradually decreases).
You don’t need to press START/STOP or PLAY/STOP to start or stop the Style or Song.
Note:
This does not work in Sequencer mode.
You can jump to the Global > Basic page by keeping
SHIFT pressed and pressing the FADE IN/OUT button.
TAP TEMPO/RESET
This is a double-function button, acting in a different way depending on whether the Style is running or not.
Note:
This button only works while in Style Play mode.
Tap Tempo:
When the Style is not playing, you can “beat” the tempo on this button. Tap as many times as the Time Signature’s numerator (for example, four times with a 4/4 Time Signature, or three times with a 3/4 one). At the end, the accompaniment starts playing, using the “tapped in” tempo.
Reset:
If you press this button while the Style is playing back, the
Style pattern goes back to the beginning of measure 1.
START/STOP
Starts or stops the Style.
Note:
This function can be automatically activated by playing the keyboard harder, by setting the “Velocity Control” parameter (in the Global > Mode Preferences > Style Play page).
You can reset all ‘frozen’ notes and controllers on the
Pa600 and any instrument connected to its MIDI OUT or the USB
Device port, by using the “Panic” (SHIFT + START/STOP) key combination. Just press SHIFT + START/STOP to stop all notes and reset all controllers.
SYNCHRO START / STOP button
These buttons turn the Synchro Start and Synchro Stop functions on or off. With this feature, you can choose to press the
START/STOP button to start and/or stop a Style, or just play the keyboard in the Chord Scan area.
Start On, Stop Off
In this situation, just play a chord in the chord recognition area to automatically start the Style. If you like, turn one of the INTROs on before starting the Style.
Start On, Stop On
When both LEDs are lit, raising your hands from the keyboard will momentarily stop the Style. If you play a chord again, the Style will start again.
Start Off, Stop On
In this case, raising your hands from the keyboard will stop the Style.
Start Off, Stop Off
All Synchro functions are turned off.
You can jump to the Global > MIDI > Setup/General Control by keeping the SHIFT button pressed and pressing the SYN-
CHRO START/STOP button.
Display and Brightness Controls
COLOR TOUCHVIEW™ GRAPHICAL DISPLAY
Use this display to interact with the instrument. To adjust the display brightness, keep the MENU button pressed, and turn the
DIAL counter-clockwise to make the display darker, or clockwise to make it brighter.
Special Function Controls
Use the TRACK SELECT, SEARCH and SHIFT buttons to choose special functions.
TRACK SELECT
Depending on the operating mode, this button switches between the various track views.
STYLE PLAY MODE
Toggles between Keyboard and Style tracks.
SONG PLAY MODE
Toggles between Keyboard tracks, Song tracks 1-
8, and Song tracks 9-16.
SEQUENCER MODE
Toggles between Song tracks 1-8 and Song tracks
9-16.
12
Overview
Front Panel
SEARCH
Press this button to open the Search window, and look for a specified file or musical resource. The Search window appears slightly different depending on the current context.
SHIFT
With this button held down, pressing certain other buttons gives access to a second function.
STS Section
Use the STS (Single Touch Settings) buttons to assign Sounds to the keyboard.
(PLAY/STOP)
Starts the Song from the current Song Position, or stops it at the current Song Position.
Lyrics, Score, Marker
Use these buttons to access the Lyrics, Score or Marker pages.
STS 1-4 buttons
These buttons allow to select up to four Single Touch Settings
(abbreviated as STS). Each one of the Styles and SongBook entries includes four Single Touch Settings (STS), to automatically configure Keyboard tracks and effects at the touch of a finger. When the STS MODE LED is lit, an STS is automatically selected when choosing a Style.
Note:
STS contained inside Factory Styles are usually write-protected (unless you uncheck the “Factory Style and Pad Protect” option in the Global > Mode Preferences > Media page)
By keeping one of these buttons pressed for about one second, the “Write Single Touch Setting” dialog box will appear.
Player Controls
Pa600 is equipped with a Standard MIDI File and MP3 Player. Its controls can be used in Song Play and Sequencer mode.
<< and >>
Rewind and Fast Forward commands, to scroll the Song back or forward.
When pressed once, these buttons move the Song to the previous or following measure (with a Standard MIDI File) or to the previous or next second (with an MP3 file). When kept pressed, they make the Song scrolling continuously until released.
In Sequencer mode, if you set a Locate Measure other than 1, when pressing the << button the Song will rewind up to that measure instead of the first one.
In Jukebox mode, keep the SHIFT button pressed, and press these buttons to scroll to the previous or next Song in the
Jukebox list.
(HOME)
Sends the Song Position back to measure 1 (i.e., the beginning of the Song).
In Sequencer mode, if you set a Locate Measure other than 1, the
Song Position will go back to that measure.
LYRICS
This button recalls the Lyrics page for the Song, the Style or the
SongBook entry.
SCORE
Press this button to open the Score page (in Song Play or Song-
Book mode).
MARKER
Press this button to open the Marker page (in Song Play or Song-
Book mode).
Data Entry and Navigation
The VALUE DIAL can be used to assign a different value to the parameter selected in the display, or to scroll a list of files in the
Song Select, SongBook,
Search and Media pages.
VALUE DIAL
Turn the dial clockwise to increase the value of the selected parameter. Turn it counter-clockwise to decrease its value.
When used while pressing the MENU button, this control always acts as a Display Brightness control.
EXIT
Use this button to perform various actions, leaving from the current status:
• exit the edit menu page, without selecting any item
• make the page menu disappear, without selecting any item
• return to the main page of the current operating mode
• exit the Global or Media edit environment, and return to the current page of the current operating mode
• exit from the SongBook mode
• exit from the Lyrics, Score and Marker pages
• exit from a Style, Pad, Performance or Sound Select window
MENU
This button opens the edit menu page for the current operating mode. After opening an edit menu, you can jump to one of the
Overview
Front Panel
13
edit sections by touching the corresponding button in the display.
Otherwise, press EXIT to return to the main page of the current operating mode, or the current page of the underlying operating mode.
Tempo Section
The TEMPO and METRO buttons can be used to control the
Tempo.
TEMPO +/– buttons
TEMPO– decreases the Tempo value of the Style or Standard
MIDI File; TEMPO+ increases it. With MP3 files, the speed of the file is respectively decreased or increased.
Press both buttons together to reset the Tempo to the value memorized in the Style or Standard MIDI File. With MP3 files, the original speed of the file is recalled (value reset to “0”).
TEMPO LOCK
This button turns the Tempo Lock function on or off.
On When you select a different Style or Performance, or select a different Song, the Tempo will not change. You can still manually change it, by using the TEMPO +/– buttons, or select the Tempo value and change it by using the VALUE dial.
Off When you select a different Style or Performance, or select a different Song, the memorized Tempo will be automatically selected.
Note:
This button does not work with MP3 files.
You can jump to the Global > Lock page by keeping
SHIFT pressed and pressing this button.
METRO
Use this button to turn the metronome click on or off.
You can jump to the Global > General Controls > Basic page by keeping SHIFT pressed, and pressing this button.
Split
Splitting the keyboard allows you to separate the chords area from the melody.
SPLIT
In Style Play, Song Play and Sequencer-Backing
Sequence mode, use this button to choose how the four Keyboard tracks are positioned on the keyboard, and how chords are recognized by the arranger.
Note:
The ACCOMP LED must be turned on for the accompaniment to play.
On The Lower track plays below the split point, while the Upper 1, Upper 2 and Upper 3 tracks play above it. This is called the Split keyboard mode.
Off
By default, turning on the Split mode automatically selects the Lower chord scanning mode. In this mode, chords are detected below the split point.
The Upper 1, Upper 2 and/or Upper 3 tracks play over the whole keyboard range. The Lower track does not play. This is also called the Full keyboard mode.
Turning off the Split mode automatically selects the Full chord scanning mode. In this mode, chords are detected over the full keyboard range.
You must always play three or more notes to let the arranger recognize a chord.
By keeping this button pressed for about one second, the
Split Point window appears. When there, play the new split point on the keyboard.
Ensemble
The Ensemble function automatically harmonizes the melody played with the right hand.
ENSEMBLE
This button turns the Ensemble function on or off.
When on, the right-hand melody is harmonized with the lefthand chords.
Note:
The Ensemble function only works when the keyboard is in
SPLIT mode.
You can jump to the Style Play > Keyboard/Ensemble page by keeping SHIFT pressed and pressing the ENSEMBLE button.
Performance Select Section
Use these buttons to select a Performance. Performances memorize all Sounds assigned to the keyboard, most control panel settings, and an associated Style.
MY SETTING
This is a special direct-access Performance, that is automatically selected when the instrument is turned on. When pressing this button, the Performance is immediately selected.
Keep this button pressed for about one second to save the current settings into the My Setting Performance.
PERFORMANCE buttons
Use these buttons to open the Performance Select window, and select a Performance.
Each Performance bank contains five pages, each with up to eight Performances. Repeatedly press a PERFORMANCE button to cycle between the available pages.
All Performances can be freely customized, by accessing the edit pages of the Style Play and Song Play modes by pressing the
MENU button.
14
Overview
Front Panel
By keeping one of these buttons pressed for about one second, the “Write Performance” dialog box will appear.
STYLE CHANGE
This button turns the Style Change function on or off.
On
Off
When you select a Performance, the Style might change according to which Style is memorized onto the Performance.
When you select a Performance, the Style will remain the same. Only Keyboard tracks (Sounds,
Effects…) will be changed.
Transpose Section
Use these buttons to transpose the Sounds.
UPPER OCTAVE
Use these buttons to transpose the Upper tracks in steps of one whole octave (12 semitones; max ±3 octaves). The octave transposition value is always shown (in octaves) next to the Sound’s name.
Press both buttons together, to reset the Octave Transpose to the saved value.
– Lowers the selected track by one octave.
+
Raises the selected track by one octave.
You can jump to the Style Play > Tuning page by keeping
SHIFT pressed and pressing one of the UPPER OCTAVE buttons. Hint: Go to the Tuning page to separately transpose each
track.
TRANSPOSE
These buttons transpose the whole instrument in steps of one semitone (Master Transpose). The transpose value is usually shown in the page header.
Press both buttons together, to reset the Master Transpose to zero.
Note:
You can also transpose MP3 files. Keep in mind, however, that transposition always remains inside the range -5…+6 semitones. This range is enough to cover all keys, but allows to avoid excessive audio degradation. Any further transposing will be reversed to fit the range. So, you might see a +7 transpose value
(Just Fifth Up) shown in the display, but the MP3 will actually play
5 semitones lower (Just Fourth Down).
♭
Lowers the Master Transpose in steps of one semitone.
♯
Raises the Master Transpose in steps of one semitone.
You can jump to the Global > Transpose Control page by keeping SHIFT pressed, and pressing one of the TRANSPOSE buttons.
Power On/Off
POWER
Use this button to let the instrument exit (LED off) or enter (LED on) standby.
Press it briefly to let the instrument exit standby. In case there are User Sounds based on User PCM Samples, loading may take some time.
Keep it pressed for about one second to let it enter standby.
Warning:
When the instrument is in standby mode, it is still connected to the power line. Accessing the inside of the instrument can be dangerous. To completely disconnect the instrument from the power, unplug the power plug from the power socket on the wall.
Note:
To avoid wasting power, Pa900 will by default automatically enter standby mode after two hours of non-active use (playing, pressing buttons or using the touch-screen). Please save your data
(Performances, Styles, Songs, and so on) before taking a prolonged pause. You can change the auto power-off timer in Global > General Controls > Clock & Power.
Overview
Rear Panel
15
Rear Panel
Music stand
Music stand holes
A music stand comes standard with your Pa600. Insert its legs into these two dedicated holes.
USB Connectors
Use these connectors to connect USB devices, or a personal computer.
HOST(R)
This is a USB Type A (Master/Host) connector, USB 2.0 compliant (High Speed only – to connect older, slower USB devices,
please use an USB hub). Use it to connect to the Pa600 an USB
Flash Memory stick, an external CD-ROM drive, an USB hard disk. You can access the connected device in the Media mode.
DEVICE
This is a USB Type B (Slave/Device) connector, USB 2.0 (High
Speed). Use it to connect the Pa600 to a personal computer, and transfer data to/from its internal memory (Disk). You can enable
USB connection in the “USB” page of the Media mode.
MIDI over USB is supported, so you can use this connector instead of the MIDI ports. The drivers for PC and Mac, needed to make full use of this type of connection, are supplied in the
Accessory Disk that comes with the instrument, or can be downloaded from our web site.
Pedals
Use these connectors to connect various types of pedals.
ASSIGNABLE
Use this port to connect a continuous- or footswitch-type pedal, like the (optional) Korg EXP-2, XVP10, PS-1 or PS-3. To program and calibrate it, go to the Controllers > Foot Controllers page of the Global mode.
DAMPER
Use this to connect a Damper pedal, like the (optional) Korg PS-
1, PS-3 or DS1H. To change its polarity and calibrate it, go to the
Controllers > Foot Controllers page of the Global mode.
Note:
Half-pedalling on Piano Sounds is available when connecting a DS1H damper pedal.
MIDI Interface
The MIDI interface allows your
Pa600 to be connected to external controllers (master keyboard, MIDI guitar, wind controller, MIDI accordion…), to a series of expanders, or to a computer running a sequencer.
OUT
This connector sends MIDI data generated by Pa600’s keyboard, controllers, and/or the internal player. Connect it to an expander’s or computer’s MIDI IN.
IN
This connector receives MIDI data from a computer or a controller. Connect it to an external controller’s or computer’s MIDI
OUT.
16
Overview
Rear Panel
AUDIO OUT Section
Use these connectors to send the audio signal (sound) to a mixer, a PA system, a set of powered monitors, or your hi-fi system.
LEFT, RIGHT
Use these line-level outputs to send the final stereo mix to an external device. Connect either of them to output the signal in mono. Adjust the output level with the MASTER VOLUME knob.
Connect two mono cables to these outputs. Connect the other end of the cables to a stereo channel of your mixer, two mono channels, two powered monitors, or the CD, LINE IN or TAPE/
AUX input of your audio system. Don’t use the PHONO inputs of your audio system!
PHONES
Connect a pair of headphones to this output. You can use headphones with an impedance of 16-200 Ohms (50 Ohms suggested). Use a headphone splitter to connect more than one pair of headphones.
AUDIO IN Section
Use these connectors to input sound from another line-level device. The signal goes directly to the final mix.
LEFT, RIGHT
Use these connectors to connect a line-level input source, such as a keyboard/ synthesizer, a CD or MP3 player, or a mixer’s
(non-powered) output. Adjust the input level with the source’s output volume.
Power
This is where you connect the Pa600 to the power line.
ACV cable connector
Plug the supplied AC cable into this connector. When the cable is connected, the instrument is in standby mode. To let it enter or exit standby, use the POWER switch located on the front panel.
Warning:
When the instrument is in standby mode, it is still connected to the power line. Accessing the inside of the instrument can be dangerous. To completely disconnect the instrument from the power, unplug the power plug from the power socket on the wall.
Start up
Connecting the AC power cord
17
Start up
Connecting the AC power cord
Connect the supplied power cord to the dedicated socket on the rear of the instrument. Then, plug it into a wall socket. You don’t need to worry about the local voltage, since the Pa600 uses a universal power adapter.
When the cable is connected to the power, the instrument automatically enters standby mode.
Turning the instrument on (or setting it to standby)
Press the POWER button on the front panel to let the instrument exit standby. The display will light up, showing the boot procedure.
Note:
When the instrument exits standby, User PCM
Samples used by some User Sounds may be automatically loaded. Loading them may take some time.
Keep the POWER button pressed for about one second to let the instrument enter standby.
Warning:
When putting the instrument in standby, all data contained in RAM (Song recorded or edited in Sequencer mode, the
Chord Sequence) will be lost.
On the contrary, data contained in the internal memory (Factory data, User Sounds, Performances, Styles) will be preserved.
• When in Style Play mode, this knob balances between the
Keyboard tracks, and the Style and Pad tracks.
• When in Song Play mode, this knob balances between the
Keyboard tracks, and the Player and Pad tracks.
This is a relative control, whose effective maximum level is determined by the MASTER VOLUME knob position.
When moved, a magnified version of the virtual slider appears in the display, for more accurate positioning.
As an alternative, the knob can be used to control the Style/Song
Volume without affecting the Keyboard tracks (choose the desired behavior by editing the “Balance Control” parameter in the Global > Controllers > Hand Control page).
Note:
This knob only works in Style Play and Song Play mode; it does not work in Sequencer mode.
Headphones
Connect a pair of headphones to the PHONES output, on the back of the instrument. You can use headphones with an impedance of 16-
200 Ohms (50 Ohms suggested). Use a headphone splitter to connect more than one pair of headphones.
Note:
When connecting the headphones, the speakers are automatically deactivated.
Controlling the Volume
Master Volume
Use the MASTER VOLUME knob to control the overall volume of the instrument. This knob controls the volume of the sound going to the integrated speakers, the AUDIO OUT and PHONES connectors.
Note:
Begin at a moderate level, then raise the MASTER VOL-
UME up. Don’t keep the volume at an uncomfortable level for too long.
Keyboard, Style Accompaniment and Song
Volume
By default, the BALANCE knob balances the volume of the Keyboard (KBD) tracks, against the Style’s Accompaniment (ACC),
Song and Pad tracks.
Loudspeakers
Pa600 is fitted with a pair of powerful, high-quality integrated speakers and a bass-reflex box, powered by a 15+15 Watt amplification system.
The overall volume can be controlled via the MASTER VOL-
UME knob.
Speakers can be deactivated with the “Speakers On/Off ” parameter, that you can find in the Global > Audio & EQ: MP3/Speakers page.
Audio Outputs
Audio outputs allow for connecting Pa600 to an external amplification system. The overall volume can be controlled via the
MASTER VOLUME knob.
MIDI connections
You can play the internal sounds of your Pa600 with an external controller, i.e. a master keyboard, a MIDI guitar, a wind controller, a MIDI accordion, or a digital piano.
18
Start up
Damper pedal
You can also control other MIDI devices with Pa600, or connect it to a computer for use with an external sequencer.
As an alternative to the MIDI connectors, you can use the USB
Device port for direct connection to a personal computer.
See the “MIDI” chapter on page 270 of the User Manual for more information on MIDI connections.
The music stand
A music stand comes standard with your Pa600. Insert its legs into the two dedicated holes on the rear panel, as shown in the illustration:
Damper pedal
Connect a Damper (Sustain) pedal to the DAMPER connector on the back panel. Use an (optional) Korg PS1, PS3 or DS1H footswitch pedal, or a compatible one. With the Korg DS1H, half-pedalling can be used on some Grand Piano sounds. To calibrate and switch the Damper polarity, go to the Controllers >
Foot Controller page of the Global mode.
Assignable pedal
Connect either a footswitch or an expression pedal to the
ASSIGNABLE connector on the back panel. Use an (optional)
Korg PS1 or PS3 footswitch pedal, a Korg EXP-2 expression pedal, a Korg XVP-10 volume pedal, or a compatible one. To calibrate the pedal, go to the Controllers > Foot Controller page of the Global mode.
Glossary of Terms
Sound
19
Glossary of Terms
Before you begin, take a few moments to familiarize yourself with the names and terms we will be using to talk about the various elements of the Pa600.
In this section, you will find a brief description of various key elements of the Pa600. A professional arranger (Pa) keyboard uses different terminology than a traditional synthesizer or workstation. By familiarizing yourself with the names and functions in this section, you will get a better understanding of how all the different parts of the Pa600 work together to create a realistic musical performance. This will also help you to get the most out of the rest of the manual.
Sound
A Sound is the most basic unit of an Arranger Keyboard performance. A Sound is basically a playable instrument timbre (piano, bass, sax, guitar…) that can be edited, saved, recalled and assigned to any track. An individual Sound can be played on the keyboard in the Sound mode. In the Style Play, Song Play or
Sequencer mode, Sounds may be freely assigned to Sequencer tracks, Style tracks, or Keyboard tracks.
Style
The Style is the heart of a professional arranger keyboard. At its basic level, a Style will consist of up to eight parts, or “Tracks”.
Drums
The Drum track will provide a repeating rhythmic phrase, played by the standard instruments of a Drum Kit.
Percussion
An additional rhythmic phrase played by various percussion instruments (conga, shaker, cowbell, etc.) is provided by the Percussion track.
Bass & Accompaniment
The Bass track and the (up to) five additional Accompaniment tracks will each play musical phrases that are musically related to and in sync with the Drum and Percussion tracks. However, the notes being played by these tracks will change to follow the chord progression that you play on the keyboard.
Again, any Sound you choose may be assigned to any track in a
Style.
Variation
For each Style, there are four Variations, to be used for the Verse,
Bridge and Chorus of a song. In general, each Variation is a slightly different version of the others. As you progress from
Variation one to Variation four, the arrangements will become more complex, and more parts (Tracks) may be added. This allows your performance to have a more dynamic arrangement, without losing the original “feel” of the Style.
Fill-in & Break
During a performance, a drummer may often perform a “fill” such as when transitioning from a verse to a chorus – adding extra dynamics and keeping the beat from getting too repetitive.
The Pa600 offers four Fill-ins specifically programmed for each
Style, that may be automatically recalled when choosing the corresponding Variation (Auto Fill). A Fill-in may be drums alone or drums with instrumentation. Then, there is even a silent
“break”.
Intro & Ending
Each Style also allows you to complete your performance with a set of musical introductions and endings. A long and short version of the Intro and Ending are usually provided, with the former more harmonically elaborated, and the latter with a fixed chord. A “count-in” Style Intro is also provided, as well as the quick Ending 3.
Pad
Pads are single sounds or single-track patterns, that can be triggered by using the dedicated PAD buttons. They can be used to play in realtime single sounds, as well as short, cycling sequences that play in time with the Style or Standard MIDI File, and are transposed according to the recognized chords.
Keyboard tracks
In addition to the Style and Pad tracks, up to four additional parts can be played on the keyboard in real-time. Each of these
Keyboard tracks can be limited to a particular range of keys or velocities, but in general up to three can be assigned to play above the split point (Upper), and one below (Lower). This allows the Upper Sounds to be layered together. The split point can be set to any note on the keyboard. In addition to performing along with a Style, these same Keyboard tracks will allow you to play along with the Player.
STS (Single Touch Settings)
Single Touch Settings allow you to instantly change the sounds assigned to each of the Keyboard tracks with a single button press, allowing for wide variation in sounds during a perfor-
20
Glossary of Terms
Performance mance. Four STS (Single Touch Settings) can be saved with each
Style or SongBook Entry.
Ensemble
By turning the Ensemble feature on, a single note played on one of the Keyboard tracks will be embellished by additional notes to create a complete chord voicing. The Ensemble knows which notes to add by looking at the chord that you are playing. In addition, the Ensemble parameters allow you to select the type of voicing that will be added – from a simple one-note harmony to a full “Brass” section – even a marimba-style trill!
Performance
The Performance is the most encompassing setting on the Pa600
– a single setting that can remember a Style (with all the appropriate sounds), the Keyboard tracks (with all the appropriate sounds) and all their Tempo, transposition, effects, etc… A Performance can be stored in one of the Performance bank locations, or it can be saved in a “database” format using the
SongBook function.
The LOGO decoder
On the front panel of your Pa600 you have probably noticed a series of logos, and may have even wondered what they stand for.
Well, here is a quick explanation of each one.
General MIDI (GM) is a standard that ensures the compatibility of sounds and messages between GM compatible instruments available from different manufacturers. For example, sequenced songs created on any GM equipped product and saved in the GM format will playback correctly on the Pa600.
General MIDI 2 extends the basic features of the General MIDI, allowing for 256 Sounds and 9 Drum Kits (instead of 128 and 1).
RX Technology is the cutting edge engine that drives every aspect of the Pa600 – from the synthesis to the display and how it all works together.
DNC (Defined Nuance Control) is the way of fine-controlling Korg’s powerful sound engine.
Every nuance and every detail of the sound can be assigned to a different control, be it the keyboard velocity or a physical controller.
Sequencer
The Sequencer acts as a recorder, so you can capture and playback your performances. The Pa600 sequencer can function in different modes. In the Backing Sequence mode, each Style element and each Keyboard and Pads element can be recorded on a separate track in a single pass. This can be a big help in getting a song recorded quickly. The sequencer can also behave as a traditional 16-track linear sequencer, where each track is recorded individually one at a time.
TouchView is the sophisticate technology allowing for touching the objects in the display, instead of pointing to them through an external device (a mouse, a series of buttons). Go straight to the musical elements, instead of catching keys somewhere on the control panel.
Player
The Player lets you playback your performances or any Standard
MIDI File or MP3 file.
Interface basics
Color TouchView graphical user interface
21
Interface basics
Color TouchView graphical user interface
Pa600 features our exclusive easy-to-use TouchView graphic interface, based on a touch‐panel LCD screen. By touching items on the LCD screen, you can select pages, tabs, and parameters, and set parameter values via on‐screen menus and buttons. Here are the basic elements of the user interface.
Menus and sections
Pages are grouped in sections, to be selected by touching the corresponding buttons in the Edit menu that opens up when you press the MENU button.
Overlapping windows
Several windows, like the Style Select or Pad Select, the Global, the Media, or the Lyrics, overlap the current window. After you select an item in the window, or press the EXIT button, the window closes, and the underlying page is shown again. (The following example is the Sound Select window).
Dialog boxes
Similar to selecting windows, dialog boxes overlap the underlaying page. Touch one of the button on the display to give Pa600 an answer, and the dialog box will close.
Pages
Parameters are grouped into separate pages, to be selected by touching the corresponding tabs on the lower area of the display.
Page menus
Touch the icon on the upper right corner of each page, and a menu with suitable commands for the current page will appear.
Touch one of the available commands to select it. (Or, touch anywhere else on the screen to make it disappear, with no command selected).
22
Interface basics
Color TouchView graphical user interface
Pop-up menus
When an arrow appears next to a parameter name, touch it to open a pop-up menu. Select any of the available options (or anywhere else on the screen to make the menu disappear).
Editable names
When the (Text Edit) button appears next to a name, touch it to open the Text Edit window and edit the name.
Checkboxes
This kind of parameters are on/off switches. Touch them to change their status.
= On
= Off
Numeric fields
When a numeric value can be edited, touch it a second time to open the Numeric Keypad.
The virtual keyboard works exactly as a personal computer’s keyboard. Some of the symbols are context-sensitive, and only appear when they can actually be used.
Lists and scrollbars
Files on storage media, as well as other kinds of data, are shown as lists. Use the scrollbar to scroll the list content. Also, you can use the VALUE DIAL to scroll.
The virtual numeric keypad works exactly as the numeric keypad of a personal computer.
As an alternative, touch a numeric field and keep it held. Then move your fingers up (or right) to increase the value, or move it down (or left) to decrease it.
List Scrollbar
When the Name label is selected, keep the SHIFT button pressed while touching one of the arrows on the scrollbar, to scroll to the next or previous alphabetic section.
Virtual sliders
To change a virtual slider’s position, select it, then use the
VALUE dial to change its position. As an alternative, touch a slider with your fingers and keep it held; then move it up or down to change its position.
This also includes the Tempo numeric field in the main page of the Style Play, Song Play, and Sequencer modes.
Interface basics
Operative modes
23
Virtual knobs
To change a virtual knob’s position, select it, then use the VALUE dial to change its position. As an alternative, touch a knob with your finger and keep it held; then move your fingers up (or right) to rotate it clockwise, or move it down (or left) to rotate the knob counter-clockwise.
Operative modes
The pages of Pa600 are grouped in various operating modes.
Each mode is accessed by pressing the corresponding button in the MODE section on the control panel.
Each operating mode is marked with a different color code, that helps you understand at first sight where you are.
Two special modes (Global and Media) overlap the current operating mode, that remains active in the background.
The Record mode can be accessed from the Style Play and
Sequencer modes, and allows for creating new Styles or Songs.
Icons
Various icons help identifying the type of a file, a Song, a folder.
For example:
Folder
File of Style bank
Standard MIDI File
Selected, highlighted items
Any operation on parameters, data or list entries, is executed on highlighted items. First select the parameter or item, then execute the operation.
Non-available, grayed-out parameters
When a parameter or command is not currently available, it is shown in grey on the display. This means it cannot be selected, but may become available when a different option is selected, or you switch to a different page.
Shortcuts
Some commands or pages can be recalled by keeping the SHIFT button pressed, and pressing other buttons or elements in the display. Some others can be accessed by keeping a button pressed for more than one second. See the “Shortcuts” chapter on page
“Shortcuts” on page 394 of the User Manual for a list of available shortcuts.
24
Easy Mode
Easy Mode
If you have never used an arranger before, we suggest you to switch to the Easy Mode. Easy Mode allows you to play Styles and Songs with a simple user interface, free from the many advanced parameters that you will want to learn later.
Turning the Easy Mode on
Touch the little rectangle on the top right corner of the display, to open the page menu:
Touch the “Easy Mode” menu item, to make the checkmark appear:
At this point, the Easy Mode has been activated, and the elements in the display appear less crowded:
The page menu
Turning the Easy Mode off
Reverse the above operation when you want to deactivate the
Easy Mode.
Easy Mode
The Style Play page in detail
25
The Style Play page in detail
To see this page, press the STYLE PLAY button.
Style name and info. Touch the Style’s name to open the Style Select window and choose a different Style.
Sounds assigned to the right hand (UP1 to UP3) and to the left hand (LOW). Touch the Sound’s name to open the Sound Select window and choose a different Sound.
Sound icon and status. If the
icon appears, the Sound is in mute and cannot be heard. If the icon does not appear, the
Sound is in play and can be
Tempo. Use the
TEMPO buttons to change it.
Length of the accompaniment pattern, and current beat.
Performance or STS. Touch it to open the Performance Select window and choose a different Performance.
Sounds on the keyboard will change.
Split Point. Touch here and play a note to set the new split point.
Mixer. Touch here, and mix the track’s volume and pan.
Effects. Touch here and choose the effects assigned to the vari- ous tracks.
Single Touch Settings (STS). Touch one of them to choose it, or use the dedicated buttons on the control panel. Sounds on the keyboard will change.
Notes:
• There are three Sounds for the right hand (Upper 1, Upper 2,
Upper 3), and a single Sound for the left hand (Lower). Their names are abbreviated as UP1, UP2, UP3, LOW, and are shown on the right side of the display.
• Right hand (Upper) and left hand (Lower) Sounds are separated by the Split Point.
• Performances and STSs are collections of Sounds. Just choose one of them to change all the keyboard’s Sounds.
• Choose a Style to change the musical style of the accompaniment patterns.
26
Easy Mode
The Song Play page in detail
The Song Play page in detail
To see this page, press the SONG PLAY button.
Song assigned to the Player. Touch it to open the
Song Select window and choose a different Song.
Tempo. Use the
TEMPO buttons to change it.
Meter (or Time Signature) and cur-
Sounds assigned to the right hand (UP1 to UP3) and to the left hand (LOW). Touch the Sound’s name to open the Sound Select window and choose a different Sound.
Sound icon and status. If the
icon appears, the Sound is in mute and cannot be heard. If the icon does not appear, the
Sound is in play and can be
open the Song Select window and choose a different Song.
Split Point. Touch here and play a note to set the new split point.
Performance or STS. Touch it to open the Performance Select window and choose a different Performance.
Sounds on the keyboard will change.
Mixer. Touch here, and mix the track’s volume and pan.
Effects. Touch here and choose the effects assigned to the vari- ous tracks.
Single Touch Settings (STS). Touch one of them to choose it, or use the dedicated buttons on the control panel. Sounds on the keyboard will change.
Notes:
• As in Style Play mode, there are three Sounds for the right hand
(Upper 1, Upper 2, Upper 3), and one Sound for the left hand
(Lower). Their names are abbreviated as UP1, UP2, UP3, LOW, and are shown in the right side of the display.
• Right hand (Upper) and left hand (Lower) Sounds are separated by the Split Point.
• Performances and STSs are collections of Sounds. Just choose one of them to change all the keyboard’s Sounds.
• Available STSs depend on the Style or SongBook Entry you last selected.
• Touching a Song name in the display is the same as pressing the
SONG button in the SELECTION section of the control panel.
28
Turning the instrument on
Turning the instrument on and viewing the main screen
Turning the instrument on
First of all, turn the instrument on and familiarize with the main screen. You can also listen to the demos.
Display Power button
Turning the instrument on and viewing the main screen
1
Turn Pa600 on (exit from standby) by pressing the POWER button located in the control panel.
After you turn the instrument on, a welcome screen is shown for some seconds, then the main display appears.
2
When you want to put Pa600 to standby, keep the POWER button pressed for about one second, and release it when the screen appears dimmed.
After having pressed the POWER button, the display brightness will be dimmed. At this point, the shutdown procedure will begin and last for a few seconds. Please do not disconnect the power cable during this procedure.
Connecting and calibrating the Damper pedal
Programming the Damper pedal
29
Connecting and calibrating the Damper pedal
If you want to play Piano, you will want to connect a Damper pedal to sustain notes while playing.
You can connect a Korg PS1, PS3 or DS1H to the DAMPER connector on the back of the instrument.
The difference between the PS1/PS3 footswitch, and a dedicated Damper pedal like the DS1H, is that this latter also supports all the nuances of half-pedalling; you can experiment how it works by gradually pressing it down, and gradually depressing it up while playing the Grand Piano RX Sound.
Damper and Assignable pedal connectors
Programming the Damper pedal
Calibrating the Damper pedal will let you use the full run of the pedal, without “dead spots”. Also, this might be the only way to connect a third-party Damper pedal that seems to work in reverse, sustaining the notes when they are not pressed!
1
Connect the Damper pedal to the DAMPER connector on the back of the instrument.
2
Press the GLOBAL button to access the Global mode.
Menu of the Global mode
Global mode is where you can set some global parameters, like this one, the Master Tuning or the Date & Time. These settings are not tied to any specific operative mode, so they are programmed in these separate pages.
3
Touch the Controllers button to access the Controllers section of the Global mode.
If you have not yet chosen a different page, the “Hand Controller” page will appear (being the first one in the Controllers section).
30
Connecting and calibrating the Damper pedal
Programming the Damper pedal
4
Touch the Foot Contr. tab to select the “Foot Controllers” page.
This is the page where you can program the Assignable Pedal/Footswitch and the Damper pedals.
5
Touch the “Calibration” button in the Damper section, to make the “Damper & Pedal/
Footswitch Calibration” dialog box appear.
6
Fully press the Damper pedal down, and while continuing to press touch the “Push” button to confirm the maximum value.
7
When the following dialog box appears, release the pedal.
8
Touch the “Push” button in the display to confirm the minimum value.
Check if the pedal is working properly. In case it isn’t, repeat the procedure.
9
Press the EXIT button to return to the previous operative mode.
Playing the Demo
Starting and stopping the Demo
31
Playing the Demo
Listen to the built-in Demo Songs to appreciate the power of Pa600. There are several Demo Songs to choose from.
Demo buttons
Starting and stopping the Demo
Here is how to start, choose and stop the Demo Songs.
1
Press the STYLE PLAY and SONG PLAY buttons together.
The LED of the two buttons will start blinking. Pa600 will be set in Demo mode.
At this point, if no other button is pressed, all the Demo Songs will be played back.
2
In case you want to listen to a specified Demo Song, select one of the available options on the display (Full Songs, Solo Instruments, Styles).
32
Playing the Demo
Starting and stopping the Demo
3
Choose one of the Demo. To stop it, touch the STOP button on the display.
4
Exit from the Demo mode by pressing any one of the MODE buttons.
Playing Sounds
Selecting a Sound and playing it on the keyboard
33
Playing Sounds
You can play up to three sounds at the same time on the keyboard. You can also split the keyboard in two parts, to play up to three sounds with your right hand (Upper) and one with your left hand
(Lower).
Split button
Sound Select button
Performance section
Selecting a Sound and playing it on the keyboard
1
Be sure the Upper 1 track is selected and set to play.
A selected track is shown with a white background. In this example, the Upper 1 track is selected. If it is not selected, touch it once to
select it.
The fact that there isn’t a icon over the bank icon means that the Upper 1 track is set to play. If it is muted, touch the
bank icon to set it to play.
i
Note: Be sure tracks
Upper 2 and Upper 3 are muted and are not playing. If you hear more than one
how to mute tracks.
2
If you want to play the Sound on the whole keyboard, be sure the keyboard is in Full
Upper mode (i.e., the SPLIT LED is turned off). If it is split in two parts, press the SPLIT button to turn its LED off.
(Full) Upper
34
Playing Sounds
Selecting a Sound and playing it on the keyboard
3
Touch the Upper 1 track’s area in the display to open the Sound Select window.
Type of Sounds.
The currently selected Sound appears in the page header.
Target track for the selected Sound
Sound’s name
i
Note: You can also open the Sound Select window by first touching the track to which to assign the new
Sound, then pressing the
SOUND button in the SELEC-
TION section.
Sound bank icon
The selected Sound is highlighted.
Touch a Sound’s name to select it.
Touch one of the side tabs to select a different Sound bank.
Touch one of the lower tabs to select a different Sound page.
A Previous and Next Page pair of button may appear in this area, when more than six pages are available.
As an alternative, repeatedly press the SOUND button to cycle between the pages.
4
Select a Sound from the Sound Select window, then press the EXIT button to close the window.
The Sound Select window closes, and the main screen appears again, with the selected
Sound assigned to the
Upper 1 track.
5
Play the Sound on the keyboard.
i
Note: Selection windows may automatically close after a selection. To do this, uncheck the “Display Hold” box in the Global > General
Controls > Interface page. In this case, press the EXIT button only if you don’t make any selection but want to close the window.
Playing Sounds
Playing two or three Sounds at the same time
35
Playing two or three Sounds at the same time
You can layer all three Upper tracks and play them on the keyboard.
Please note how the icon appears in the Upper 2 and Upper 3 status boxes.
These tracks will not be heard.
1
Touch the icon in the Upper 2 status box, to set the Upper 2 track to play.
After touching in this area, the disappears. The
icon
Upper 2 track will be set to play and will be heard.
2
Play the keyboard.
Note how the ‘Dark Pad’ Sound (assigned to the Upper 2 track) has been layered with the ‘Grand Piano RX’ (assigned to the Upper 1 track).
3
Touch the icon in the Upper 3 status box, to set the Upper 3 track to play.
As above, after touching in this area, the
icon disappears. The Upper 3 track will be set to play and will be heard.
4
Play the keyboard.
Note how the ‘Strings Ens.2 GM’ Sound (assigned to the Upper 3 track) has been added to the ‘Dark Pad’ (assigned to the Upper 2 track) and the ‘Grand Piano RX’
(assigned to the Upper 1 track).
5
Touch the bank icon in the Upper 3 status box, to mute the Upper 3 track again.
36
Playing Sounds
Playing two or three Sounds at the same time
6
Play the keyboard.
Note how the ‘Strings Ens.2 GM’ Sound (assigned to the Upper 3 track) has been muted again. Only tracks Upper 1 and Upper 2 can be heard at this time.
7
Touch the bank icon in the Upper 2 status box, to mute the Upper 2 track again.
8
Play the keyboard.
Note how the ‘Dark Pad’ Sound (assigned to the Upper 2 track) has been muted again. Only track Upper 1 can be heard at this time.
Playing Sounds
Playing different Sounds with your left and right hand
37
Playing different Sounds with your left and right hand
You can play a single Sound with your left hand, in addition to playing up to three Sounds with your right hand.
1
Press the SPLIT button to turn its LED on, and split the keyboard in the Lower (left hand) and Upper (right hand) parts.
Upper
Lower
2
Be sure the Lower track is set to play.
If the Lower track is muted, touch its icon to make it disappear from this area.
If the Bass & Lower Backing function is turned on, and the Style is not running, the Lower track will always play.
3
Play the keyboard.
Note how the keyboard is split in two parts, each playing different sounds.
Lower Upper
38
Playing Sounds
Playing different Sounds with your left and right hand
4
Return to the full keyboard playing mode by pressing the SPLIT button to turn its LED off.
5
Play the keyboard.
(Full) Upper
Note how the keyboard once again plays the Upper tracks over the entire length of the keyboard.
Upper
Changing the split point
If you are not comfortable with the selected split point, you may set the split point to a different key.
1
Touch the Split tab to see the Split Point panel.
Playing Sounds
Changing the split point
39
2
Touch the keyboard in the display, then play the lowest note of the Upper section on the keyboard.
i
Hint: As an alternative, keep the SPLIT button pressed to open the Split
Point dialog.
Upper
Lower
3
As an alternative, touch the Split Point parameter to select it, and use the VALUE dial to select the new split point.
When you change the split point, the “Global” parameter is automatically unchecked. This is because you are setting a “local” or “temporary” split point, and not the “global” one, used across the whole instrument.
To change the “global” split point, go to the Global > Mode Preferences > Style page, and set the
“Split Point” parameter.
You can save the “local” split point into a Performance, as described in the following pages (see
“Saving your settings to a Performance” on page 42).
40
Playing Sounds
Raising or lowering the Upper octave
Raising or lowering the Upper octave
If all Upper tracks sound too high or too low, you can quickly change which octave they are playing in.
1
Use the UPPER OCTAVE buttons on the control panel, to transpose all Upper tracks at the same time.
i
Note: The Octave Transpose value for each of the keyboard track is shown under the Sound’s name.
Each time you press this button, the pitch will be lowered by one octave.
Each time you press this button, the pitch will be raised by one octave.
2
Press both UPPER OCTAVE buttons together to reset the octave to the value saved in the current Performance.
Selecting and saving Performances
Selecting a Performance
41
Selecting and saving Performances
Performances are the musical heart of Pa600.
Unlike selecting single Sounds, selecting a Performance will recall several Sounds at the same time, the needed effects and transpositions, plus many more parameters useful for playing in a musical situation (like the Assignable Switches). Performance can be considered a snapshot of the current situation.
You can save these settings to a Performance memory location. While many Performances are already supplied with the instrument, you can customize each of them to your own taste, and then save them in their customized version.
Similar to Performances, but dedicated to the Styles and SongBook Entries, you can also save your settings to a Single Touch Setting (STS), which will store all the settings for the Keyboard tracks.
Four STSs are supplied with each Style and SongBook Entry, and can be selected with the four dedicated buttons under the display.
Please note that settings saved in the "My Setting" Performance are automatically selected when
the instrument is turned on (exit from standby).
This means you can save your preferred startup settings to this Performance (see below for more information).
Single Touch Settings (STS) section Performance section
Note: Style tracks are saved to a third object called the
Style Settings.
Selecting a Performance
1
Touch the Performance area in the display, to open the Performance Select window.
i
Hint: You can also open the Performance Select window by pressing one of the buttons in the PERFOR-
MANCE section. This will let you jump directly to the desired Performance bank.
The selected Performance is highlighted. Touch a Performance name to select it.
Touch one of the side tabs to select a different Performance bank.
Touch one of the lower tabs to select a different Performance page.
42
Selecting and saving Performances
Saving your settings to a Performance
2
Select one of the Performances in the Performance Select window, then press the EXIT button to close the window.
After pressing the EXIT button, the Performance Select window closes, and the main screen appears again. Sounds, Effects, and other settings, change according to the setting memorized in the selected Performance.
Note that Selection windows may automatically close after a selection. To do this, uncheck the
“Display Hold” box in the Global > General Controls > Interface page. In this case, press the
EXIT button only if you don’t make any selection but want to close the window.
3
Play the keyboard.
Settings memorized in the selected Performance have been selected. Sounds, effects and other settings have been recalled.
i
Note: If the
LED of the STYLE
CHANGE button is turned on, selecting a Performance may automatically select a different Style and its settings (Sounds,
Effects for the Style tracks…)
Saving your settings to a Performance
The Sounds and Effects assigned to the Keyboard tracks, together with the parameters you can access by pressing the MENU button while in Style Play and Song Play mode, can be saved into a single Performance, to be quickly recalled at a later time.
1
Keep one of the PERFORMANCE buttons pressed for about one second to open the
Write Performance dialog box.
i
Hint: To open the Write
Performance dialog box, you can also choose the ‘Write
Performance’ command from the page menu.
Selecting and saving Performances
Saving your settings to a Performance
43
2
If you like, you may assign a new name to the Performance.
Use the ‘<–’ and ‘–>’ buttons or the DIAL to move the cursor.
Touch the ‘Backspace’ symbol to delete just a single character, ‘Clear’ to delete the whole string.
Use the alphabetic characters to enter text.
Touch the (Text Edit) symbol to open the
Text Edit dialog box.
Touch the Shift key to switch between capitals and small characters.
3
Select a bank and Performance location in memory, where you would like to save the
Performance.
When done, touch OK to confirm the new name, or Cancel to abandon all changes.
The selected Performance location is highlighted. Touch a
Performance’s name to select it.
Touch one of the side tabs to select a different Performance bank.
Touch one of the lower tabs to select a different Performance page.
4
When you have edited the name to the Performance, and selected the target location, touch OK to save the Performance to memory (or Cancel to stop the operation).
!
Warning: Saving a Performance to an already used location overwrites any existing data at that location. The old data are lost. Make a backup of all your important data.
44
Selecting and saving the “My Setting” Performance
Selecting the startup parameters (the "My Setting" Performance)
Selecting and saving the “My Setting” Performance
There is a special Performance, where you can save your preferred startup settings for things like Keyboard Sounds, Effects, Transposition, Assignable Switches. This Performance is automatically
selected when the instrument is turned on (exit from standby).
It is called the “My Setting” Performance.
‘My Setting’ Performance
Selecting the startup parameters (the "My Setting" Performance)
After having done some changes to the Sounds, transposition, or other parameters, you can return to the startup situation by pressing the MY SETTING button in the control panel.
• Press the MY SETTING button to recall the “startup” settings.
Saving the startup parameters into the "My Setting" Performance
You can save the startup settings (Sounds and other settings, including most of the settings on the control panel) into this special Performance.
•
Keep the MY SETTING button pressed for about one second, until the “Write Startup
Settings” dialog box appears, then touch the OK button to confirm saving to memory.
Selecting and playing Styles
Selecting and playing a Style
45
Selecting and playing Styles
Pa600 is an arranger, i.e. a musical instrument providing automatic accompaniments, or arrange-
ments. Each arrangement style is called, as a consequence, a Style.
A Style is made of several Style Elements (Intro, Variation, Fill, Break, Ending), corresponding to the various sections of a song. By selecting Style Elements, you can make your playing more varied and musical.
When selecting a Style, Sounds, Effects and various configuration parameters for the Style tracks are also selected. These are called the Style Settings. Selecting a Style also selects the four Pads it contains.
Pads are single sounds or single-track patterns, that can be triggered with the dedicated PAD buttons.
If the STS MODE LED is turned on, the first of the four Single Touch Settings (STS) associated to the
Style is also selected, and Keyboard tracks, Effects and some other useful parameters are automatically configured.
Use the Style controls to start or stop the Style.
Style Select and STS Mode buttons
Style Elements
Style Controls
Selecting and playing a Style
1
Touch the Style area in the display. The Style Select window appears.
Type of Style.
The selected Style is highlighted.
Touch a Style’s name to select it.
Touch one of the side tabs to select a different Style bank.
Touch one of the lower tabs to select a different Style page.
i
Hint: You can also open the Style Select window by pressing the STYLE button in the SELECTION section of the control panel.
46
Selecting and playing Styles
Selecting and playing a Style
2
Select a Style from the Style Select window.
After pressing the EXIT button, the Style Select window closes, and the main screen appears again, with the selected
Style ready to go.
3
Be sure the ACCOMP. LED is turned on.
For the accompaniment tracks to play, the LED of this button (meaning “Accompaniment”) must be turned on.
4
Press the SYNCHRO-START/STOP button to turn the START LED on.
This will turn the Synchro-Start function on, and let the accompaniment start as soon as you play a chord on the keyboard.
START LED
STOP LED
i
Note: You could simply press START/STOP to start the
Style, but the Synchro-Start function allows you to make the Style start in sync with your playing on the keyboard. Therefore, it may be considered a “more musical” way of starting a Style.
5
Play the keyboard.
When the Syncho-Start function is turned on, the Style starts playing as soon as you play a note or chord in the chord scan area.
Play chords with your left hand, and the melody with your right hand. The arranger will follow your playing.
6
Press START/STOP to stop the Style.
i
Note: The chord scan area depends on the status of the SPLIT LED and the Chord
Recognition parameter (see
Global > Mode Preferences >
Style).
Selecting and playing Styles
Tempo
47
Tempo
While a Tempo setting is saved with each Style or Performance, you can change it to be whatever you like. You can use either of the following two methods.
• Use the TEMPO + or – buttons to change the Tempo value.
i
Hint: As an alternative to using the TEMPO buttons, hold the Tempo value in the display, then move your finger up/down or left/right (or change the value with the
VALUE dial).
• Press the TEMPO – and + buttons together to recall the saved Tempo value.
•
As an alternative, keep the SHIFT button pressed, and use the VALUE dial to change the
Tempo. The selected tempo will be shown in a small window.
• If you like to keep the currently selected Tempo value unchanged, turn on the LED of the TEMPO (LOCK) button.
When the Tempo Lock function is turned on, the Tempo will not change when selecting a different Style (or a different Song in Song Play mode).
48
Selecting and playing Styles
Intro, Variation, Fill, Break, Ending
Intro, Variation, Fill, Break, Ending
When playing Styles, you can select various “Style Elements” to cover the various sections of a song. A
Style is made of three Intros (or two Intros and a Count-In), up to four basic patterns (Variations), four Fills, a Break, and three Endings.
1
Make sure the SYNCHRO-START LED is turned on (otherwise, press the button to turn it on).
Activating the Synchro Start function is not mandatory, but it might be handy.
2
Press one of the INTRO buttons to set the corresponding Intro to play.
3
Play the keyboard.
The Style starts with the selected Intro. When the Intro is completed, the basic pattern (selected Variation) starts to play.
4
Be sure the LED of the AUTO FILL button is turned on.
When the Auto Fill function is turned on, a Fill is automatically performed before switching to a different variation.
5
While playing, press one of the VARIATION buttons, to select a different variation of the basic pattern.
If you turned the Auto Fill function on in the previous step, a Fill will be performed before the
Variation begins.
When the Fill ends, the selected Variation will start playing.
Selecting and playing Styles
Single Touch Settings (STS)
49
6
When you like to stop playing, press one of the ENDING buttons to stop the Style with an Ending.
When the Ending is finished, the Style automatically stops.
Single Touch Settings (STS)
Each Style or SongBook Entry may come with up to four Keyboard track settings, called the STS
(short for “Single Touch Settings”). STSs are very similar to Performances, but they are fine-tuned to the Style or SongBook Entry they are associated to.
If the STS MODE LED is turned on, STS #1 is automatically selected when choosing a Style. STS #1 is also recalled each time a SongBook Entry is selected.
1
In case it is not shown, touch the STS Name tab to see the STS Name panel.
2
Press one of the four STS buttons under the display, or touch the name of an STS in the
STS panel in the display.
3
Play the keyboard.
Settings memorized in the selected STS have been selected.
Sounds, effects and other settings have been recalled.
4
Try all the other STSs, and see how settings change with each of them.
5
You can also link the STSs to the Variations. First of all press the STS MODE button, to make its LED flash.
50
Selecting and playing Styles
The Pads
6
Then press the various VARIATION buttons, and see how an STS is automatically selected when the corresponding Variation is selected.
7
Press the STS MODE again to turn its LED on (or off).
The Pads
Each Style or SongBook Entry can assign different sounds or patterns to the four PADS. These sounds or patterns can be played along with the Keyboard and Style tracks.
1
If you want to see which sounds or patterns are associated to the four Pads for the current Style, touch the Pad tab to see the Pad panel.
2
Press one of the four PADS to play the corresponding Pad.
3
If the selected PAD triggers an endless pattern (i.e. a guitar arpeggio), press the same
PAD button again to stop it.
4
Select a different Style, and see how the sounds or patterns assigned to the PADS change.
5
Press more PAD buttons at once, to play two or more sounds or patterns at the same time.
6
Press STOP to stop all the Pads at the same time.
i
Hint: You can open the
Pad Select window to assign a different sound or pattern to the Pads, by pressing SHIFT
+ one of the PADs.
Selecting and playing Styles
Adjusting the balance between the Style and the keyboard
51
Adjusting the balance between the Style and the keyboard
Balancing between the Keyboard and Style tracks may be useful, to gently fade them and adjust their respective volume.
•
While the Style is playing, use the BALANCE knob to balance between the Keyboard
(KBD) and Style’s Accompaniment (ACC) volume.
This knob also balances between the Keyboard and the Pad tracks. Also, it balances between the
Keyboard and the Song tracks (in Song Play mode).
Adjusting the volume of the separate tracks
You can adjust the volume of each of the Style and Keyboard tracks, for example to soften the bass a little, or to make the keyboard solo louder.
1
Touch the Volume tab to see the Volume panel.
2
Hold & drag the Virtual Sliders in the display to adjust each Keyboard track’s volume.
52
Selecting and playing Styles
Turning the Style tracks on/off
3
To separately adjust each Style track, press the TRACK SELECT button to change the track’s view.
i
Hint: As an alternative, you can change each track’s volume, by touching a track’s area to select it, then using the VALUE dial to change the volume.
In Style view, all separate
Style tracks are shown, and their volume can be adjusted by dragging the corresponding sliders.
4
To return to the Keyboard Tracks view, press the TRACK SELECT button again.
Turning the Style tracks on/off
You may easily turn on or off any Style track while you are playing. For example, try muting all accompaniment tracks, while drums and bass continue to play.
1
Be sure the Volume panel is shown, or touch the Volume tab to show it.
i
Note: While in the Normal view of the Style Play mode, you can see Style tracks grouped in just three
“grouped” tracks. To see each
Style track as separate, individual tracks, just press the
TRACK SELECT button.
2
While the Style is playing, touch the Play button to set the track to Mute.
Mute the ACCOMP track. All accompaniment tracks will go silent (apart from Drum, Percussion and Bass).
3
To set the tracks back to the Play status, touch the Mute icon on the muted track.
i
Hint: To turn all Accompaniment tracks (including the Bass track) off while you are not in the Main page, press the ACCOMP button on the control panel to turn its
LED off.
Set the ACCOMP track to Play. All accompaniment tracks will return to their original volumes.
Selecting and playing Styles
Turning the Style tracks on/off
53
4
To mute/unmute each single Style track, first press TRACK SELECT to switch to the Style
Tracks view, then repeat the above procedure.
5
Press the TRACK SELECT button again to go back to the Normal view.
54
Selecting and playing Styles
Adding harmony notes to your right-hand melody with the ENSEMBLE function
Adding harmony notes to your right-hand melody with the
ENSEMBLE function
Chords played with your left hand may be applied to the right-hand melody.
1
Press the SPLIT button to turn its LED on and split the keyboard.
The Ensemble function only works in Split mode.
2
Press the ENSEMBLE button to turn its LED on.
3
Play chords with the left hand and single notes in the right hand.
Notice how the right hand is automatically harmonized, according to the chords composed with your left hand.
4
To select a different harmonization style, keep the SHIFT button pressed, and press the
ENSEMBLE button to open the Ensemble page.
This is a fast ‘shortcut’ to recall this page. The longer procedure would have consisted in accessing the Edit mode by pressing the MENU button, touching the Keyboard/Ensemble section, and then going to the Ensemble page.
While the Ensemble parameter is selected, use the VALUE dial to select one of the available harmonization types.
Selecting and playing Styles
Adding harmony notes to your right-hand melody with the ENSEMBLE function
55
5
When the right harmonization type has been selected, press the EXIT button to go back to the main page.
While in an Edit page, press EXIT to go back to the Main page of the current operating mode.
6
Press the ENSEMBLE button again to turn its LED off. The automatic harmonization will be turned off.
56
Selecting and playing Styles
The Chord Sequencer
The Chord Sequencer
In case you need both hands free for playing a solo while a Style is playing, you can record a Chord
Sequence and let Pa600 play the chords for you.
1
Press the START/STOP button to set the Style to play.
2
Press the MEMORY and MAN. BASS (RECORD) buttons together to start recording.
3
Start recording your Chord Sequence at the beginning of the next measure.
While recording, you will see a red flashing icon in the display.
4
Play the chords in the chord scan area.
The chord scan area is under the Split Point if the SPLIT LED is turned on. Usually, it is over the whole keyboard if the SPLIT LED is turned off. The chord scan area also depends on the status of the Chord Recognition parameter (Global > Mode Preferences > Style).
5
When the Chord Sequence is done, press the MEMORY and MAN. BASS (RECORD) buttons together again to stop recording.
i
Hint: You can avoid stopping the Chord Sequencer after recording, and immediately set the Sequence to play, as explained in the following step.
6
Press the ACCOMP. and MEMORY (PLAY/STOP) buttons to start playback.
The LED of the two buttons will start flashing. The Chord Sequence will be played back in loop starting from the next measure. Recorded chords will be sent to the arranger, and the Style will play with the recorded chords.
7
Play your solo part, while the Chord Sequencer plays the chords for you.
During Chord Sequence looping, you can freely select any Fill or Variation, as if you where playing chords with your hands.
Selecting and playing Styles
The Chord Sequencer
57
8
Press the ACCOMP. and MEMORY (PLAY/STOP) buttons together again to stop playback of the recorded Chord Sequence.
The last chord played by the Chord Sequence remains in memory. The Chord Sequence will remain in memory up until you record a new Chord Sequence, or you set Pa600 to standby.
58
Song Play
Selecting a Song to play
Song Play
Pa600 is equipped with an onboard Player that can read Songs in Standard MIDI File (MID), Karaoke™ (KAR) and MP3 format. It may be of great interest to singers and guitar players to know that if a
Standard MIDI File or an MP3 file contains lyrics and chords, they can be seen in the display. Lyrics in the graphical “+G” format are also supported.
In addition to lyrics and chords, with Standard MIDI Files and Karaoke files you can also see the score in traditional notation, as well as the markers, to quickly jump to any section of a Song.
The SONG PLAY button
Player controls
Selecting a Song to play
1
Press the SONG PLAY button to switch to the Song Play mode.
After pressing the SONG PLAY button, the main page of the Song
Play mode appears.
i
Hint: In Style Play mode, you can pre-select the Song to be assigned to the Player.
This way, you will be ready to start it, as soon as you switch to Song Play mode.
The Song area of the
Style Play main page.
Song Play
Selecting a Song to play
59
2
Touch the Player area to open the Song Select window.
This window is very similar to the one you can see when pressing the MEDIA button on the control panel, and touching the Load tab to see the Load page. This page is, however, “filtered” to only show Song files.
i
Hint: As an alternative, you can open the Song Select window by pressing the
SONG button in the SELEC-
TION section of the control panel.
3
Scroll through the list and select the Song to play.
The selected Song is highlighted. Touch a Song’s name to select it.
Use the Device pop-up menu to select one of the available mass-storage devices.
Use the Open and Close buttons to browse through the folders.
4
When the Song is selected, touch the Select button to confirm your selection; this will automatically close the Song Select window.
Selected Song
Use the scroll bar or the VALUE DIAL to see all the Songs in the list. Keep
SHIFT pressed and touch the Up/
Down arrow to jump to the next/ previous alphabetic section.
Touch the Select button to select the highlighted Song, and assign it to the Player.
Use the Locate button to ‘locate’ and go to the folder of the selected Song.
After touching the Select button in the display, the main page of the Song Play mode will appear again.
60
Song Play
Playing back a Song
Playing back a Song
Once a Song has been selected, it may be played back by the Player.
1
Press the (PLAY/STOP) button in the PLAYER section to start playback.
After pressing the (PLAY/STOP) button, the button’s LED turns on, and the measure counter begins to show the current measure number.
2
Use the PLAYER control section to control the Song’s playback.
Press the REWIND button once to goback.
Keep it pressed to go back more.
Press the FAST FORWARD button once to goforward.
Keep it pressed to go forward more.
Press the PLAY/STOP button to stop the Song at the current position. Press it again to resume playback.
Press the HOME button to move to the beginning of the Song.
3
When you want to stop the song and go back to the beginning, press the (HOME) button.
When the Song is stopped, the LED on the PLAY/STOP button turns off.
i
Note: In any case, the
Player will automatically stop when the end of the Song is reached.
Song Play
Changing the tracks’ volume
61
Changing the tracks’ volume
While playing back a Standard MIDI File, you may wish to change each track’s volume, to create a mix
“on the fly”.
1
Be sure the Volume panel is shown, or touch the Volume tab to show it.
2
As seen for the Styles, you can hold & drag the Virtual Sliders on the display to adjust each track’s volume. Use the TRACK SELECT button to cycle between track groups.
Use the TRACK
SELECT button to cycle between different groups of tracks
3
In Normal view, you can adjust each Keyboard track’s volume.
i
Hint: As an alternative, you can change each track’s volume, by touching a track’s area to select it, then using the VALUE dial to change the volume.
Keyboard tracks
62
Song Play
Changing the tracks’ volume
4
Press the TRACK SELECT button once to see tracks 1-8 (Track 1-8 view).
In Track 1-8 view, the first 8 tracks of the selected Song are shown.
5
Press TRACK SELECT once again to see tracks 9-16 (Track 9-16 view).
In Track 9-16 view, the second group of 8 tracks of the selected
Song are shown.
6
Press TRACK SELECT again, to return to the Normal view (Keyboard tracks).
i
Note: Changes to Song tracks will not be saved, and are reset each time you press the (Home) button, or you select a different Marker. To save changes, you must edit the Song in Sequencer mode.
7
Press the (PLAY/STOP) button to start the Song.
Keyboard tracks
8
While listening to the Song, switch from Normal view to Track 1-8 and Track 9-16 view, to see which tracks are playing.
To see if a track is playing, look at the label with its name, and see if it is changing color.
• Touch each track’s channel strip, to see each track’s detail in the Track Info line.
Song Play
Turning the Song tracks on/off
63
Selected track Assigned Sound. Touch it to open the Sound Select window.
Sound bank Program Change
•
Also, you can see which type of Sound is assigned to each track in the Sound area of the
Track 1-8 and Track 9-16 views.
Octave Transpose
Sound bank icons. Touch to open the
Sound Select window.
Turning the Song tracks on/off
While playing back a Standard MIDI File, you may wish to mute one or more tracks, for example to sing along with the Song, or play an instrumental part live on the keyboard.
To mute/unmute Song tracks you simply touch the Play/Mute icon in the Volume panel.
64
Song Play
Soloing a track
Soloing a track
Opposite to the above, you may want to make a single track of a Standard MIDI File play alone. This is called the Solo function.
1
While the Song is playing, keep the SHIFT button pressed and touch the track you want to listen to in Solo mode.
2
To set all tracks back to the Play status, keep the SHIFT button pressed again, and touch the track that is currently in Solo mode.
Please remember that you can also use the Solo function in Style Play and Sequencer mode. The
Solo command can also be selected from the page menu.
Removing the Melody track from a Standard MIDI File or the Lead
Vocal from an MP3 file
If you want to sing along with a Song (in Standard MIDI File or MP3 format), you can remove the
Melody track or the Lead Vocal from the Song. Please note that removing the Lead Vocal from an
MP3 file may be more or less effective, depending on the Song.
Programming the Assignable Switches
1
Program the Assignable Switches as the Song-Melody and Vocal Remover switches.
Press the MENU button, and choose the “Pad/Assignable Switch” section. Then touch the
Switch tab to open the “Switch” page. While in this page, assign the Song-Melody function to the
ASSIGNABLE SWITCH 1, and the Vocal Remover function to the ASSIGNABLE SWITCH 2:
i
Hint: You can open this page by keeping the SHIFT button pressed and pressing one of the ASSIGNABLE
SWITCHES.
2
Press the EXIT button to return to the main page of the Song Play mode.
Using the Assignable Switches with a Song
1
Assign a Song (either in Standard MIDI File or MP3 format) to the Player.
2
Start the Player.
3
Press the ASSIGNABLE SWITCH 1 to mute the Melody track, or the ASSIGNABLE
SWITCH 2 to activate the Vocal Remover, and remove the Melody track or the original lead singer’s voice.
Listen how the Melody track disappears. If it is the wrong track, continue to the instructions below to select a different track.
Or, listen to how the original lead singer’s voice is reduced or totally removed.
i
Note: The Assignable
Switches’ assignment can be saved into each Performance or STS.
Song Play
Removing the Melody track from a Standard MIDI File or the Lead Vocal from an MP3 file
65
4
When done, you can press the ASSIGNABLE SWITCH 1 to unmute the Song’s Melody track and let the original MIDI instrument play the Melody line again, or press the
ASSIGNABLE SWITCH 2 to deactivate the Vocal Remover and let the original lead singer’s voice appear again.
5
Stop the Player.
Choosing a different Melody track
You can choose a different Melody track, in case the Standard MIDI Files does not use a standard configuration of tracks.
1
Keep the SHIFT button pressed and press the SONG PLAY button to open the Global >
Mode Preferences > Song Play & Sequencer page.
2
Choose a different Melody track.
3
When done, press EXIT to return to the main page.
66
The SongBook
Selecting the desired Entry from the Main List
The SongBook
One of the most powerful features of Pa600 is the onboard music database, that allows you to organize your Styles and Songs for easy retrieving. Each Entry of this database may include the artist, title, genre, number, key, tempo, and meter (time signature) of a specified song. When selecting one of the
Entries, the associated Style, Standard MIDI File or MP3 file – as well as the Style Play or Song Play mode – is automatically recalled.
In addition to helping you organize your shows, the SongBook allows you to assign up to four Pads, and up to four STSs to each Entry. Also, you can link a text file to any Entry, to be used as the Lyrics of a song, even if there are no Lyrics events in the associated Standard MIDI File or MP3 file, or if you prefer to play the song live with the backing of the Styles.
You can add your own Entries to the SongBook, as well as edit the existing ones. Korg has already supplied some hundred Entries as standard. Furthermore, the SongBook allows you to create various custom lists, that may suit your different types of show.
The SONGBOOK button
Selecting the desired Entry from the Main List
A large database is already included with the instrument, and you can later customize it. You may browse through this database in a variety of ways.
1
While you are in Style Play or Song Play mode, press the SONGBOOK button to open the SongBook window.
Style, Standard MIDI File(s) or MP3 file(s) currently assigned to the arranger or player(s)
Use the scroll bar or the
VALUE DIAL to see all the
Songs in the list. Keep SHIFT pressed and touch the Up/
Down arrow to jump to the next/previous alphabetic section.
SongBook Main List
Touch this checkbox to turn the view filter on.
Touch this button to edit the view filter.
Adds the selected Entry to the Custom List (if acti-
Touch this button to select the current Entry to play.
2
Browse through the Entries.
Icons in the Type column will help you identify the type of the Entry. The Genre column is
shown by default, but you can switch to the Artist column (see “Displaying Artist or Genre”
below).
3
When the Entry you are looking for becomes visible in the display, select it and touch the Select button in the display.
After selecting an Entry, the corresponding Style, MID, KAR or MP3 file will be recalled, together with the relevant operating mode (Style Play or Song Play). Up to four STSs and four
Pads will also be recalled. Any TXT file associated with the Entry can be seen in the Lyrics page.
The selected Style, MID, KAR or MP3 file will be shown in the top area of the screen.
The SongBook
Displaying Artist or Genre
67
Displaying Artist or Genre
For space matters, either the Genre or Artist column can be seen in the display. You cannot see both at the same time.
1
Touch the page menu icon to open the page menu.
i
Note: The Artist and Key fields of all supplied Entries have been intentionally left empty.
2
Choose Show Artist (now Genre) to switch from Genre to Artist in the List view. The Artist column will be shown.
3
Open the page menu again, and choose the Show Genre (now Artist) item. The Genre column will be shown again.
68
The SongBook
Sorting Entries
Sorting Entries
You can change the order of the Entries shown in the display.
1
You can change the sorting order by touching one of the labels in a list of names.
Touch the Name label…
…to alphabetically reorder the names in the list.
You can do the same by touching the Type, Name, Genre, Artist, Key, Number, Tempo or Meter label.
2
Each time you touch the same label again, the order changes between ascending and descending.
Searching for Entries
The SongBook database may be really huge. You can, however, look for (say) specific artists or song titles, using the filtering functions.
1
Touch the Filter button in the display, to open the Filter dialog box.
Available search criteria. “Genre” and “Artist” are both considered, even though only one of them may be shown in the List
2
Touch the (Text Edit) button next to the search criteria (even more than one) you want to enter.
For example, you may want to find all songs containing the word “love” in the title (in any position in the string). If so, select the ‘Name’ criterion, and enter the word ‘love’. Capitals are not relevant for the search.
The SongBook
Searching for Entries
69
3
Touch OK in the display, and close the Text Edit dialog box. The entered text is now the search criteria.
4
Touch OK to close the Filter dialog box and return to the SongBook page.
Once the Filter dialog box has been closed by touching OK, the Filtered check box is automatically checked, and the filter is activated. Only Entries matching the entered criterion are seen in the Main List.
5
To see the whole SongBook database again, touch the Filtered check box again, to make the check mark disappear.
70
The SongBook
Adding Entries
Adding Entries
You can add your own Entries to the SongBook database.
1
Go to the Style Play or Song Play mode, depending on the type of Entry you want to add to the SongBook database.
2
Select the Style, Standard MIDI File or MP3 file to be added to the SongBook.
3
Edit the Keyboard and Style tracks the way you prefer, by selecting different Sounds and Effects, or editing any other relevant parameter.
Please note that changes to Standard MIDI File tracks will not be saved as SongBook data. Only the data included in the Standard MIDI File will be used.
4
Choose a Voice Processor Preset.
5
When ready, keep the SONGBOOK button pressed for about one second to create a new SongBook Entry with the current settings.
6
Touch the (Text Edit) button to assign a name to the Entry, then touch OK to save the Entry to the SongBook database.
Editing the Entries
You can edit any SongBook Entry and customize it according to your taste. When done, you can overwrite the current Entry or save it as a new Entry.
1
Press the SONGBOOK button to access the SongBook pages.
2
Touch the Book Edit 1 tab to see the Book Edit 1 page and see the linked Musical
Resources.
While in the Book Edit 1 page, you will be able to see the name of the selected Style or Song, and choose whether to replace them or not.
Name of the Style or Song file linked to the Entry.
Name of the Entry
If checked, the current Style track settings, or the path of the
Song file (shown on the right), are saved with the Entry. If unchecked, current settings are left unchanged.
This parameter is automatically checked when touching the
New Song button to create a new Entry.
If checked, you can either save all the current STSs into the
Entry, or choose a single STS where to save the current Keyboard track settings.
The SongBook
Editing the Entries
71
Song Selection number (ID number for numeric selection)
3
When done with this page, touch the Book Edit 2 tab to see the Book Edit 2 page and edit the SongBook database details.
Database Entry’s parameters
4
Touch the (Text Edit) button next to the field(s) you want to edit. Set all the other parameters.
You can write the Genre and Artist name. Select a Tempo matching the Song’s Tempo, and select the Meter (Time Signature) and Key of the Song. You can also specify a Master Transpose value, to be automatically selected when selecting the Entry.
5
When done with this page, touch the Book Edit 3 tab to go to the Book Edit 3 page, where you can and set the Synchro and Memory parameters, and link a text file to the
Entry.
i
Note: The Master Transpose might not change, if a
Lock is preventing it. See
Global > General Controls >
Locks.
Synchro (for Style) and Memory (for Style and Songs) On/Off status
Text file linked to the Entry.
This text will be seen in the same way of ordinary Lyrics in the display (or in the external monitor).
72
The SongBook
Creating a Custom List
6
After having filled up all the desired fields (be as comprehensive as you can), touch the
Write button in the display to open the Write dialog box.
7
Touch the (Text Edit) button to assign a name to the Entry, then touch OK to save the Entry to the SongBook database.
Select Rename/Overwrite to replace an existing Entry. This option is automatically selected when editing an existing
Entry; it cannot be selected when saving a new Entry. Warning: the older Entry
will be deleted!
Entry’s name. By default it is the same name of the associated Style, Standard MIDI File of MP3 file. The name can be up to 16 characters long.
Select New Song to add a new Entry to the SongBook database. This option is automatically selected when a new Entry has been created (by touching the New
Song button).
Creating a Custom List
You can create several Custom Lists in the SongBook, to make a set of Entries suitable for your various shows. Before starting a new Custom List, be sure you have added all needed Entries to the Song-
Book main database (see “Adding Entries” above).
1
While in SongBook mode, open the page menu and check the ‘Enable List Edit’ item.
After you check the
‘Enable List Edit’ item, the List Edit page becomes available.
2
Select a Custom List to be edited.
To edit an existing list, touch the Custom List tab to open the Custom List page, and select one of the available Custom Lists. To create a new list, touch the List Edit tab to open the List Edit page, and touch the New List button to create a new, blank list.
The SongBook
Creating a Custom List
73
3
Touch the Book tab to open the Book page and see the full database. Use the various sorting, searching and filtering options (seen above) to find the Entries you are looking for. Touch the Add to List button when the desired Entry has been selected.
SongBook list
Use the scroll bar or the VALUE DIAL to see all the Songs in the list. Keep SHIFT pressed and touch the
Up/Down arrow to jump to the next/previous alphabetic section.
Touch this checkbox to turn the view filter on (if any).
Touch this button to edit the view filter.
Adds the highlighted Entry to the
Custom List.
4
When finished adding Entries to the Custom List, touch the List Edit tab to go to the List
Edit page, and use the various commands to edit the list.
List name
Scrollbar
Select an Entry to be edited from the list
Use the vertical arrows to move the selected
Entry up or down in the list.
Touch Write to save the current
Custom List.
Touch Del Song to delete the selected Entry.
Touch New List to create a new Custom List. Touch
Del List to delete the current Custom List. Warning:
Del List will delete the current Custom List.
5
When the Custom List is ready, touch the Write button in the display to save it to memory. Assign a new name to the Custom List.
Use thearrows or the VALUE DIAL to move the cursor.
Touch Delete to delete just a single character, Clear to delete the whole string.
Use alphabetic characters to enter text.
Touch the (Text Edit) symbol to open the
Text Edit dialog box.
Touch the Shift key to switch between capitals and small characters.
When done, touch OK to confirm the new name, or Cancel to abandon all changes.
6
When finished editing the Custom List, open the page menu and uncheck the ‘Enable
List Edit’ item.
74
The SongBook
Selecting and using a Custom List
Selecting and using a Custom List
After having created one or more Custom Lists, you can select one and use it for your show.
1
Touch the Custom List tab to select the Custom List page.
2
Use the List pop-up menu to select one of the available Custom Lists.
Use the List pop-up menu to select one of the available Custom Lists.
Entry in play. To select a different one, highlight it and touch the Select button in the display.
Touch Select to set the highlighted Entry to play (if different than the one automatically selected).
Touch Next to select the next Entry in the list.
(This command can also be assigned to an
Assignable Switch).
3
Select one of the Entries in the list (it turns blue), then touch the Select button in the display to confirm selection (the selected Entry turns green). Press the PLAY button to start playing back the selected Song.
Recording a new Song (Standard MIDI File)
Preparing the Style and Sounds
75
Recording a new Song (Standard MIDI File)
There are several ways to create a Song on the Pa600. The easiest and fastest is to use the Styles to record what you are playing in realtime on the keyboard, while the arranger gives you the accompaniment tracks.
SEQUENCER button
Player controls
Style Elements Style Controls
Preparing the Style and Sounds
Before accessing the Record mode, we suggest you prepare the Style and Sounds with which to record your Song.
1
Select a Style with which you want to record.
2
Select the Sounds by choosing a Performance or STS.
That’s all! You are ready to access Record mode.
Accessing the Backing Sequence (Quick Record) mode
1
Press the SEQUENCER button to switch to the Sequencer mode.
After pressing the
SEQUENCER button, the main page of the Sequencer mode appears.
76
Recording a new Song (Standard MIDI File)
Accessing the Backing Sequence (Quick Record) mode
2
Press the RECORD button to open the Song Record Mode Select dialog box.
Press the RECORD button, to open the Song Record Mode
Select dialog box
3
Select the Backing Sequence (Quick Record) option and touch OK to enter the Backing
Sequence Record mode.
After having chosen the Backing Sequence
(Quick Record) option, the Backing
Sequence Record page appears.
Recording a new Song (Standard MIDI File)
Setting the Record parameters
77
Setting the Record parameters
When you enter Backing Sequence Record, the latest selected Style and Sounds are already selected, and all tracks are ready to record. You could simply start recording as if you were playing in realtime with the Styles. However, there are some further settings that you may want to do.
• If you like, adjust any editable parameter in the display.
Track(s) status. ‘Rec’ means they are ready to record. ‘Play’ means they are recorded and you can hear them. ‘Mute’ means they cannot be heard.
Touch the Style parameter (or the STYLE button) to open the Style Select window, and select a different Style.
Measure counter. The negative number ( -1) is the precount, after which you can start recording.
Style’s Tempo. Change it, if you like.
Style’s Meter (or Time
Signature). It’s just an indicator, you cannot change it.
Touch the Perf/STS parameter to open the
Performance Select window, and select a different Performance (as seen
native, you use the PER-
FORMANCE or STS buttons.
Grouped tracks. During Quick Record, you cannot access each separate Song track. For ease of use, just two ‘master’ tracks are provided: Kbd/Pad (Keyboard/Pads) and Ch/Acc (Chord/Accompaniment).
Recording
1
Select the Style Element you wish to use before starting to play.
Select any of the Variations before starting to record.
Select one of the Intros to start with an introduction.
2
Start recording, by pressing the START/STOP button.
3
Play as if you were performing live with the Styles.
During recording, select any Style Element (Intro, Variation, Break, Ending…) you like. You can also press START/STOP to stop the Style, and press it again to start the Style again!
Please remember that, while recording in Backing Sequence Record mode, you cannot use the
SYNCHRO, TAP TEMPO/RESET, BALANCE controls.
i
Note: If you do not wish to start the Song with the
Style already playing, you can simply start recording by pressing the PLAY/
STOP button in the PLAYER section, then start the Style only at a later time. The Style will start at the beginning of the following measure.
78
Recording a new Song (Standard MIDI File)
Recording
4
When finished recording your Song, press the (PLAY/STOP) button in the PLAYER section to exit recording, and return to the main page of the Sequencer mode.
After pressing the PLAY/STOP button, the main page of the Sequencer mode will appear again.
5
While in the main page of the Sequencer mode, press the (PLAY/STOP) button in the PLAYER section to listen to the recorded Song.
The Backing Sequence Song has been converted to an ordinary Song (in Standard MIDI File, or
“MID”, format). If you like it, you can save it. You can then read it in Song Play mode, or transfer it to any external sequencer.
6
If you want to edit the Song, press MENU to access Edit mode.
Recording a new Song (Standard MIDI File)
Second-take recording (Overdubbing)
79
Second-take recording (Overdubbing)
You may want to record an additional “grouped” track, or replace a bad-recorded track with a new one. A good idea may be to record all chords and Style Element changes during the first take, then record Keyboard tracks and Pads during the second take.
1
Press the RECORD button to enter Record mode again. When the Song Record Mode
Select dialog box appears, select Backing Sequence (Quick Record) again.
2
If you are recording just one of the “grouped” tracks, set to Play the track to be preserved.
3
Repeat the recording procedure, and press the (PLAY/STOP) button in the PLAYER section to stop recording and return to the main page of the Sequencer mode.
4
While in the main page of the Sequencer mode, press the (PLAY/STOP) button in the PLAYER section to listen to the recorded Song.
Again, the Backing Sequence Song has been converted to an ordinary Song.
Saving a Song
After having recorded a Song that you like, it is a good idea to save it, to avoid losing it when the instrument is turned off (or put in standby).
1
While in the main page of the Sequencer mode, touch the page menu icon to open the page menu.
80
Recording a new Song (Standard MIDI File)
Saving a Song
2
Select the Save Song command to open the Save Song window.
This window is very similar to the one you can see when pressing the MEDIA button on the control panel, and touch the Save tab to see the Save page. This page is, however, “filtered” to only see Song files.
After you select the Save song command, the Save Song page appears.
3
Select a device and folder where you want to save your Song.
If a Song is selected (highlighted) it will be overwritten. If no Song is selected, a new Song file will be created on the target device.
To deselect a selected Song, touch anywhere else in the Song list, or select the same storage device again.
Use the Device pop-up menu to select one of the available storage devices
Use the Open and Close buttons to browse through the folders.
4
Touch the Save button in the display to open the Save Song dialog box.
Touch the Text Edit icon to edit the Song’s name.
Use the scroll bar to see all Songs in the list. Keep SHIFT pressed and touch the
Up/Down arrow to scroll to the next/previous alphabetic section. As an alternative, you can use the VALUE DIAL.
Touch the Save button to save the Song to the current folder.
In case you prefer to exit this page without saving the Song, press the EXIT button.
5
Touch OK in the display to save the Song, or Cancel to stop the Save operation.
Searching files and musical resources
How to use the Search function
81
Searching files and musical resources
With Pa600, you can press the SEARCH button to search for files or musical resources.
How to use the Search function
Depending on the page you are in, you can search for different types of data. For example, while in
Media mode you can only search for files, while in Style Play or Song Play mode you can search for several different types of data (Styles, Songs, Lyrics…).
There are some pages where the Search function is not available, since there are no relevant data to search for that page (for example, the pages of the Global mode).
Here is the general procedure.
1
Press the SEARCH button to open the Search window.
2
If needed, touch the “Type” pop-up menu, and choose the type of item you are looking for.
When choosing Files, Songs or Lyrics, the “Browse” button will be activated, to allow for searching files in the disks.
82
Searching files and musical resources
How to use the Search function
3
In case you are searching for a file in a disk, touch the “Browse” button to open the
Media window.
When you see the folder containing the file you are looking for, touch it, then touch the Select button to close the Media window. The name of the selected folder will be shown in the title bar of the Search window.
Use the Device pop-up menu to select one of the available storage devices
Use the Open and Close buttons to browse through the folders
In case you are lost among the directories, touch the “Root” button to go to the root of the selected device
4
Type the name of the file to be searched.
There is no difference between upper and lower cases (“LOVE” is the same as “Love” or “love”).
5
When finished entering the name, touch the “Search” button.
After a while, the list of files found begins to appear in the display.
i
Note: Only one search atime can be carried on. Please wait for the current search to be completed, or touch the
Stop button in the display to stop the current search and do a new one.
After you have touched the “Search” button, its name changes to “Stop”. If needed, touch this button to stop the ongoing search. The name of the button reverts to “Search”. Any file found will remain in the display, until you do a new search.
The time needed to complete a search depends on the size of the device(s) and the number of files.
i
Hint: You can touch the
Cancel button in the display, or press the EXIT button in the control panel, to exit from this window and carry on other operations. The search will continue in the background.
Searching files and musical resources
Notes about searching
83
6
You can touch one of the found items to select it, and then touch the “Info” button to see information on it.
Touch OK to close the Info dialog box.
7
If you want to return to the main Search page and type a search string again, touch the
icon. Otherwise,
8
If you have found what you were looking for, touch its name and then touch the
“Select” command.
9
You can exit from the Search window at any time, by pressing the EXIT or SEARCH button.
Notes about searching
Wildcards
During search, the string entered will be search as a whole word or as part of a word. For example, if you entered “love”, Pa600 will find “Love” and “LoveSong”, or any other word containing the string
“love”.
You can use the wildcards “?” (any single character) and “*” (any sequence of characters) to search exactly that string. For example, “*love” will find “MyLove”, but not “LoveSong”. “??love” will find
“MyLove” but not “TrueLove”.
Also, if you are looking for words that can be spelled in a slightly different way, you can use the “?” wildcard to find all occurrences; “gr?y” will find out both “gray” and “grey”.
84
Searching files and musical resources
Notes about searching
86
Replacing the clock backup battery
Precautions
Replacing the clock backup battery
You can replace the clock backup battery with a standard lithium battery (model CR2032). Do not use replacements different
than the one supplied or suggested by Korg, or you risk to damage the instrument!
The battery can be replaced by the user. Korg is not responsible for any data loss, damage or
injury caused by incorrect installation of this part.
4.
Use the flat-head screwdriver to open the cover (b) to gain access to the inside of the battery slot, and keep the cover apart.
Precautions
• Installation of the battery is done at the user’s own risk. Korg will assume no responsibility for any damage or injury resulting from its improper installation or use.
• Be sure to disconnect the instrument from the AC plug, before opening it.
• To prevent your body’s static electricity from damaging the board’s components, touch an unpainted metallic component before proceeding with the installation.
ⓑ
5.
With the help of your fingernail, lift the exhausted battery
(c) from its lower side, and remove it from the battery slot.
Installation
For installation, you will need a cross-point and a flatt-head screwdrivers (not supplied).
1.
Disconnect the instrument from the AC power.
2.
3.
Extract the battery from its package.
From the back of the instrument, use the cross-point screwdriver to remove the fixing screw (a).
ⓐ
Replacing the clock backup battery
Installation
87
6.
Insert the new battery (d) into the empty battery slot, being sure the positive (+) side is facing up.
7.
Replace the cover (b) to the original position. Attach the cover to the back of the instrument by using the fixing screw (a).
ⓓ ⓐ ⓑ
88
Technical specifications
Technical specifications
KORG Pa600 Features Pa600 Standard Pa600 Quarter Tone
PHYSICAL DATA
Cabinet
Keyboard
SOUNDS
Tone Generator
Factory Sounds
User Sounds
Sound Edit
PCM Sample RAM
Effects
Keyboard Tracks
Performances / STS
STYLES
Factory Styles
Favorite/User Styles
Arranger Tracks
128 Oscillators, Three band EQ for each track, Filters with resonance, DNC (Defined Nuance Control)
More than 950, including Stereo Piano and GM Level 1 & 2 compatible sounds; 64 Drum Kits
256 Sounds, 128 Drum Kits
On-board full editing for Sounds and DrumKits
96 MB for loading User Sounds
4 Master Stereo Digital Multi-Effects, 125 Effect types; Mastering Limiter and Final 4-band Parametric EQ
Four Keyboard tracks (Upper 1, 2, 3, Lower)
320 Performance locations, all programmable; Up to 4 STSs x Style, up to 4 x SongBook entry
Style Edit
Patterns/Chord Variations
Style Controls
Pads
Compatibility
Operating System
DATA STORAGE
More than 360 preloaded Styles, freely reconfigurable
10 Favorite banks, plus 3 User banks, for a total of 1,120 Style locations (Factory + Favorite/User)
Eight Style tracks, 4 Single Touch Settings (STS), 4 Pads and one Style Settings per Style, Guitar Track Mode 2, Parallel and Fixed
NTT
Style Record with Step Record, Track and Event Edit functions, Import/Export SMF
Up to 46 patterns for each Style, including 3 Intros, 4 Variations, 4 Fills, 1 Break, 3 Endings
3 Intros, 4 Variations, 4 Fills, Break, 3 Endings, Auto Fill, Synchro Start/Stop, Manual Bass, Memory, Accompaniment On/Off,
Single Touch
Realtime Style Chord Sequence Recorder Chord Sequencer
PLAYER/SEQUENCER
Player
4 STS saved with the Song
Tracks
Player with Song Select, Start/Stop, Home, Rewind, Fast Forward controls; Supported formats: MID, MID+G, KAR, MP3 + lyrics,
MP3+G; Lyrics, Score, and Chord data can be displayed on screen; Markers; Jukebox function
In SongBook Mode
16
Sequencer Edit Record & Edit functions; SMF native format
Backing Sequence (Quick Record) Real Time Record - Step Record & Edit
Lyrics/Chords
Score View
On-Screen (compatible with most popular formats); +G format supported
On-screen
Markers On-screen
SONGBOOK
SongBook and SongBook List Fully programmable music database, based on Styles, SMF, Karaoke, MP3 with automatic selection of Style Play and Song Play modes; User-definable custom lists; Filtering and Ordering options
OTHER FEATURES
MP3
Quarter Tone / Arabic Scale
MP3 Player in Song Play mode; Vocal Remover; Tempo change ±30%, Transpose -5~+6 semitones
Programmable, with up to 4 SC Presets Programmable, with up to 4 SC Presets; Dedicated Quarter
Tone keypad
4 + Stop button i-Series: Styles (some adjustments may be needed); Pa-series: Style, Pad, Performance, Sound, PCM Sample, Song, SongBook
RX (Real eXperience), DNC (Defined Nuance Control), Multitasking system, Load while play feature, Upgradable, Internal clock
Internal Memory
USB Port for Memory Devices
USER INTERFACE
Display
Controls
Heavy-duty plastic
61 keys with velocity
Standard
Yes - 1 Host (2.0 Hi Speed)
7" 800 x 480 TFT Graphical Color Touch Screen Display
Dial, Master Volume, Accompaniment/Player/Keyboard Volume Balance, Transpose, Octave Transpose, Ensemble, Tap Tempo/
Reset, Tempo+/-, Tempo Lock, Fade In/Out
Technical specifications
89
KORG Pa600 Features
Programmable Controls
CONNECTIONS
MIDI
USB
Outputs
Inputs
Headphone
Pedals
Power Supply
AMPLIFICATION
Amplification and Speakers
ACCESSORIES
Supplied Accessories
OPTIONS
USB Memory
Expression/Volume Pedal
Damper Pedal
Footswitch
PHYSICAL DATA
Consumption
Dimensions (W x D x H)
Weight
Pa600 Standard
Joystick, 2 Switches, Assignable Pedal/Footswitch
IN, OUT
1 Host (2.0 Hi Speed) and 1 Device (2.0 Hi Speed); MIDI Over USB
2 Analog (Left/Right)
2 Analog (Left/Right)
1 jack connection
1 Damper, 1 Assignable Pedal/Footswitch
AC - Universal Voltage
Pa600 Quarter Tone
2 Channel Amplification System; 2x15 Watt; 2 x 100 mm Double-Cone Speakers in Bass Reflex Box
Manual, AC Power Cable, Music Stand, DVD
Yes
Korg EXP-2, Korg XVP-10
Korg DS-1H
Korg PS-1, PS-3
20 Watt
1030 x 378 x 127 mm / 40.55 x 14.88 x 5.00 inch without music stand
9.74 kg / 21.47 lbs 9.8 kg / 21.61 lbs
Specifications and appearance are subject to change without notice for improvement.
90
MIDI Implementation Chart
MIDI Implementation Chart
KORG Pa600
OS Version 1.1 - April 01, 2013
Function Transmitted Recognized Remarks
Basic Channel
Mode
Note
Number:
Velocity
Aftertouch
Pitch Bend
Control
Change
Program
Change
System Exclusive
System
Common
System
Real Time
Default
Changed
Default
Messages
Altered
True Voice
Note On
Note Off
Poly (Key)
Mono (Channel)
0, 32
1, 2
6
38
7, 11
10, 91, 93
64, 66, 67
65, 5
71, 72, 73
74, 75
76, 77, 78
98, 99
100, 101
120, 121
True #
Song Position
Song Select
Tune
Clock
Commands
1–16
1–16
X
****************
0–127
****************
O 9n, V=1–127
O 8n, V=0–127
O
O
O
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O 0–127
****************
O
X
X
X
O
O
1–16
1–16
3
X
0–127
0–127
O 9n, V=1–127
O 8n, V=0–127
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O 0–127
0–127
O
X
X
X
O
O
Memorized
Player data only
Player data only
Bank Select (MSB, LSB)
Modulations
Data Entry MSB
Data Entry LSB
Volume, Expression
Panpot, A/B Master FX Send
Damper, Sostenuto, Soft
Portamento On/Off, Portamento Time
Harmonic Content, EG time (Release, Attack)
Brightness, Decay Time
Vibrato Rate, Depth, Delay
NRPN (LSB, MSB)
RPN (LSB, MSB)
All sounds off, Reset all controllers
Aux
Messages
Local On/Off
All Notes Off
Active Sense
X
X
O
X
O (123-124)
O
Notes
Mode 1:OMNI ON, POLY
Mode 3:OMNI OFF, POLY
Reset X X
*1: Sent and received when MIDI Filters In and Out are set to Off in Global mode.
*2: Sound parameters, Selection of SongBook entries, Drum Kit Family settings.
*3: LSB, MSB = 00,00: Pitch Bend range, =01,00: Fine Tune, =02,00: Coarse Tune.
*4: Includes Inquiry and Master Volume messages, FX settings, Quarter Tone settings. GM Mode On.
*5: Transmitted only when the Clock Send parameter (Global mode) is set to on.
Mode 2:OMNI ON, MONO
Mode 4:OMNI OFF, MONO
O: Yes
X: No
*1
*1
*1
*1, 2
*1, 3
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*4
*5
*5
Address
KORG ITALY SpA
Via Cagiata, 85
I-60027 Osimo (An)
Italy
Web
www.korg.com
www.korg.co.jp
www.korg.co.uk
PART NUMBER: MAN0010047
© KORG Italy 2013. All rights reserved
advertisement