S-AIR Operations. Sony STR-DN1000
Advertisement
Advertisement
S-AIR Operations
About S-AIR products
This receiver is compatible with the S-AIR
function (page 117), which allows wireless
sound transmission between S-AIR products.
When you purchase the S-AIR product, you
need to establish sound transmission (page
There are two types of S-AIR product.
• S-AIR main unit (this receiver):
The S-AIR main unit is for transmitting sound.
You can use up to 3 S-AIR main units. (The number of usable S-AIR main unit depends on the use environment.)
• S-AIR sub unit (not supplied): The S-AIR sub unit is for receiving sound.
– Surround amplifier: You can enjoy surround and surround back speakers sound wirelessly. For details, refer to the operating instructions supplied with the surround amplifier.
– S-AIR receiver: You can enjoy system sound in another room.
These S-AIR products can be purchased as an option (the S-AIR product lineup differs depending on the area).
Notes or instructions for the surround amplifier or S-AIR receiver in this operating instructions is refer only when the surround amplifier or S-AIR receiver is used.
Room B
S-AIR sub unit
(S-AIR receiver)
Room A
?/1
S-AIR main unit
(this receiver)
MULTI CHANNEL DECODING
SPEAKERS
2 CH/
A.DIRECT
A.F.D.
MOVIE MUSIC INPUT MODE DIMMER DISPLAY
MASTER VOLUME
INPUT SELECTOR
MUTING
AUTO CAL MIC VIDEO
VIDEO 2 IN
L AUDIO R PHONES
S-AIR sub unit
(surround amplifier)
To use S-AIR products (S-AIR main unit and sub unit)
Before using S-AIR products, have the following ready.
Confirm the wireless adapters are inserted correctly
Insert the wireless adapters firmly to the depth into the slots of the S-AIR main unit and sub unit respectively.
Insert firmly
continued
89
GB
Confirm that the S-AIR IDs of the S-AIR main unit and sub unit are the same
The default setting of the S-AIR IDs of the
S-AIR main unit and sub unit is “A”.
Depending on the S-AIR product, you can set the S-AIR ID by the switch or the setup menu.
For details, refer to the operating instructions of each S-AIR product.
About environments where
S-AIR products (S-AIR main unit and sub unit) are used
S-AIR products use a radio frequency of
2.4 GHz. Certain electronic equipment or other factors may cause lost connection or instability in S-AIR reception.
• Electronic equipment influence
The following may cause interference or cross talk.
– Cellular phones, cordless phones
– Wireless LAN, personal computers
– Game machines using radio signals
– Microwave ovens
Setting up an S-AIR product
Before using an S-AIR product, be sure to perform the following settings to establish the sound transmission.
Inserting the wireless transmitter/transceiver
To make use of the S-AIR function, you need to insert the wireless transmitter (not supplied) into the S-AIR main unit and the wireless transceiver (not supplied) into the S-AIR sub unit.
Notes
• Before inserting the wireless transmitter/ transceiver, be sure to disconnect the AC power cord (mains lead).
• Do not touch the terminals of the wireless transmitter/transceiver.
• Other factors
The following may cause poor reception.
– Materials or structures, such as walls and floors
– The location where an S-AIR product is placed
When using S-AIR products, place them as far as possible from the above electronic equipment, or place where S-AIR reception is stable.
90
GB
To insert the wireless transmitter into the S-AIR main unit
1
Remove the screws and detach the slot cover.
Slot cover
Notes
• Insert the wireless transmitter with the S-AIR logo facing up.
• Insert the wireless transmitter so that the V marks are aligned.
• Do not insert other than the wireless transmitter into the EZW-T100 slot.
3
Use the screws that you removed from step 1 to fasten the wireless transmitter.
ANTENNA
AM
Y
IN 3
COMPONENT VIDEO
IN 2 IN 1 MONITOR
OUT
DMPORT
DC5V
0.7A MAX
P
C
B
/
P
R
/
C
R
ASSIGNABLE (INPUT ONLY)
OUT
L
IN
R
SA-CD/CD/CD-R
IN
TV
TV DIG
OP
VIDEO
IN
VIDEO
IN
VIDEO
OUT
VIDEO
IN
AUDIO
IN
AUDIO
IN
SAT BD
OPTICAL IN
VIDEO
OUT
SAT IN
AUDIO
OUT
L
AUDIO
IN
MONITOR
AUDIO
OUT
R
VIDEO 1
SUBWOOFER
SURROUN
FRON
BI-A
R
Notes
• Remove the screws from the slot cover bearing the caution mark. Do not remove other screws.
• The slot cover is no longer necessary. However, keep it after detaching.
2
Insert the wireless transmitter.
EZW-T100 slot
Note
Do not use other screws to fasten the wireless transmitter.
To insert the wireless transceiver into the S-AIR sub unit
For details on installing the wireless transceiver into surround amplifier and S-AIR receiver, refer to the operating instructions supplied with the surround amplifier and
S-AIR receiver.
Wireless transmitter
91
GB
Establishing sound transmission between the S-AIR main unit and
S-AIR sub unit (ID setting)
When you match the ID of the S-AIR main unit and the S-AIR sub unit, you can establish sound transmission. You can use multiple
S-AIR main unit by setting a different ID for each unit.
2CH/
A.DIRECT
RESOLUTION
A.F.D.
INPUT
MODE
MOVIE
SLEEP
MUSIC
NIGHT
MODE
DISPLAY GUI MODE
GUI MODE
V/v/b,
O
RETURN/
EXIT
HOME
MENU
.
< <
TOOLS/
OPTIONS
>
MENU
5
Press V/v repeatedly to select the ID
(A, B or C) you want, then press .
The ID of the S-AIR main unit is set. “Set
S-AIR ID of the sub unit to the same as that of the main unit” appears.
6
Press to set the ID of the S-AIR sub unit.
7
Press GUI MODE.
The GUI menu turns off.
8
Set the S-AIR sub unit to the same ID.
Sound transmission is established as follows (example):
S-AIR main unit
?/1
MULTI CHANNEL DECODING MASTER VOLUME
SPEAKERS
2 CH/
A.DIRECT
A.F.D.
MOVIE MUSIC INPUT MODE DIMMER DISPLAY
INPUT SELECTOR
MUTING
AUTO CAL MIC VIDEO
VIDEO 2 IN
L AUDIO R PHONES
ID A
To set the ID of the S-AIR main unit
1
Press GUI MODE.
After “MENU ON” appears on the display for a while, “GUI” appears and the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not appear on the TV screen.
2
Press V/v repeatedly to select
“Settings”, then press or b.
The Settings menu list appears on the TV screen.
3
Press V/v repeatedly to select “S-AIR”, then press or b.
Note
When the S-AIR transmitter (not supplied) is not inserted into the S-AIR main unit, “S-AIR” cannot be selected.
4
Press
V/v repeatedly to select “S-AIR
ID”, then press or b.
The S-AIR ID menu appears.
ID A
S-AIR sub unit
ID A
S-AIR sub unit
Tip
To confirm the current ID, performs steps 1 to 3 above. When you pair the S-AIR main unit with
the S-AIR sub unit (page 93), “(Pairing)”
appears beside the ID on the TV screen in the
GUI menu.
To exit the menu
Press MENU.
To set the ID of the S-AIR sub unit
Be sure to match the ID on S-AIR sub unit you want to the S-AIR main unit.
For details on setting the ID of the surround amplifier and S-AIR receiver, refer to the operating instructions supplied with the surround amplifier and S-AIR receiver.
92
GB
To use multiple S-AIR main units
You can use multiple S-AIR main units by setting a different ID for each component.
S-AIR main unit
?/1
MULTI CHANNEL DECODING
SPEAKERS
2 CH/
A.DIRECT
A.F.D.
MOVIE MUSIC INPUT MODE DIMMER DISPLAY
MASTER VOLUME
INPUT SELECTOR
MUTING
AUTO CAL MIC VIDEO
VIDEO 2 IN
L AUDIO R PHONES
ID A
Other S-AIR main unit
ID B
ID A
S-AIR sub unit
ID A
S-AIR sub unit
ID B
S-AIR sub unit
Notes
• Sources with copyright protection may not be playable on S-AIR sub unit.
• When sound transmission is established
– sound can only be output from the S-AIR receiver if you connect the components to this receiver via the analog jacks. The sound cannot be output if the components are connected to the
COAXIAL, OPTICAL or HDMI jacks on this receiver.
– the headphones function on the surround amplifier is not available.
Pairing the S-AIR main unit with a specific S-AIR sub unit
(Pairing operation)
To establish sound transmission, you need to set the same ID for your S-AIR main unit and
S-AIR sub unit.
However, if your neighbours have S-AIR products and their IDs are the same as yours, your neighbours could receive the sound of your S-AIR main unit or vice versa.
To prevent this, you can pair the S-AIR main unit with a specific S-AIR sub unit by performing the pairing operation.
x Before pairing
Sound transmission is established by the ID
(example).
Your room Neighbour
PHONES
?/1
S-AIR main unit
MULTI CHANNEL DECODING
SPEAKERS
2 CH/
A.DIRECT
A.F.D.
MOVIE MUSIC INPUT MODE DIMMER DISPLAY
MASTER VOLUME
INPUT SELECTOR
MUTING
AUTO CAL MIC VIDEO
VIDEO 2 IN
L AUDIO R
ID A
ID A
S-AIR sub unit
ID A
S-AIR sub unit
continued
93
GB
x After pairing
Sound transmission is established between the paired S-AIR main unit and S-AIR sub unit(s) only.
Your room Neighbour
PHONES
?/1
S-AIR main unit
MULTI CHANNEL DECODING MASTER VOLUME
INPUT SELECTOR
MUTING
AUTO CAL MIC VIDEO
VIDEO 2 IN
L AUDIO R
SPEAKERS
2 CH/
A.DIRECT
A.F.D.
MOVIE MUSIC INPUT MODE DIMMER DISPLAY
No transmission
ID A
S-AIR sub unit
Pairing
ID A
S-AIR sub unit
To perform pairing
2CH/
A.DIRECT
A.F.D.
MOVIE
RESOLUTION
INPUT
MODE SLEEP
MUSIC
NIGHT
MODE
DISPLAY GUI MODE
GUI MODE
V/v/B/b,
RETURN/
EXIT O
O
RETURN/
EXIT
HOME
MENU
.
< <
TOOLS/
OPTIONS
>
MENU
1
Place the S-AIR sub unit that you want to pair near the S-AIR main unit.
2
Match the IDs of the S-AIR main unit and the S-AIR sub unit.
• To set the ID of the S-AIR main unit,
see “To set the ID of the S-AIR main unit” (page 92).
• To set the ID of the S-AIR sub unit, refer to the operating instructions supplied with the S-AIR sub unit.
3
Press GUI MODE.
After “MENU ON” appears on the display for a while, “GUI” appears and the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not appear on the TV screen.
4
Press
V/v repeatedly to select
“Settings”, then press or
b.
The Settings menu list appears on the TV screen.
5
Press
V/v repeatedly to select
“S-AIR”, then press .
The S-AIR menu appears.
Note
When the S-AIR transmitter (not supplied) is not inserted into the S-AIR main unit, “S-AIR” cannot be selected.
6
Press
V/v repeatedly to select
“Pairing”, then press .
“Put the S-AIR sub unit near the S-AIR main unit. Turn on power and start pairing.” appears on the TV screen. The
S-AIR main unit is ready to start pairing.
7
Press
B/b repeatedly to select
“Yes”, then press .
The S-AIR main unit starts pairing.
“Pairing. Do the pairing operation with the S-AIR sub unit.” appears.
8
Start pairing of the S-AIR sub unit.
Refer to the operating instructions of the
S-AIR sub unit.
Notes
• Perform pairing within 5 minutes in step 6. If you do not, pairing is recognized as failed, and the screen changes accordingly. In this
case, see “If pairing fails” (page 95).
• When sound transmission is established,
“Pairing complete. To perform pairing to another S-AIR sub unit, select “Continue”.” appears.
94
GB
9
Press
B/b repeatedly to select
“Finish” or “Continue”, then press .
• “Finish”: Finishes pairing.
• “Continue”: Continues to perform pairing to another S-AIR sub unit.
Tip
You can confirm the pairing completion or the current ID by checking the “S-AIR Settings” screen. “(PAIRING)” appears beside the current S-AIR ID.
10
Press GUI MODE.
The GUI menu turns off.
Note
After you have performed pairing, if you select the “S-AIR ID” menu, the ID setting (“A", “B” or “C”) that you last used is displayed.
If pairing fails
“Pairing failed. Retry?” appears.
To perform pairing again, select “Yes”.
To finish pairing, select “No”.
To quit pairing during setting
Press RETURN/EXIT O.
To cancel pairing
Perform the ID setting of the main unit
according to the procedure of “To set the ID of the S-AIR main unit” (page 92). If you reset
the ID (even the same ID again), pairing is canceled.
Enjoying the system’s sound in another room
(For the S-AIR receiver only (not supplied))
You can enjoy the system’s sound in another room by using the S-AIR receiver. The S-AIR receiver can be placed in another room for enjoying the system’s sound there.
For details of the S-AIR receiver, refer to the operating instructions supplied with the S-AIR receiver.
2CH/
A.DIRECT
RESOLUTION
A.F.D.
INPUT
MODE
MOVIE
SLEEP
MUSIC
NIGHT
MODE
DISPLAY GUI MODE
GUI MODE
V/v/b,
O
RETURN/
EXIT
HOME
MENU
.
< <
TOOLS/
OPTIONS
>
MENU
1
Set the ID of the S-AIR receiver to match the ID of the S-AIR main unit.
• To set the ID of the S-AIR main unit,
see “To set the ID of the S-AIR main unit” (page 92).
• To set the ID of the S-AIR receiver, refer to the operating instructions supplied with the S-AIR receiver.
Notes
• When you are using another S-AIR sub unit, such as a surround amplifier, do not change the ID of the S-AIR main unit. Set the ID of the S-AIR receiver to match the ID of the
S-AIR main unit.
• When you pair the S-AIR main unit and another S-AIR sub unit, such as a surround amplifier, you also need to pair the S-AIR main unit and the S-AIR receiver. For details,
see “Pairing the S-AIR main unit with a specific S-AIR sub unit (Pairing operation)”
continued
95
GB
2
Press GUI MODE.
After “MENU ON” appears on the display for a while, “GUI” appears and the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not appear on the TV screen.
3
Press
V/v repeatedly to select
“Settings”, then press or
b.
The Settings menu list appears on the TV screen.
4
Press
V/v repeatedly to select
“S-AIR”, then press or
b.
Note
When the S-AIR transmitter (not supplied) is not inserted into the S-AIR main unit, “S-AIR” cannot be selected.
5
Press
V/v repeatedly to select
“S-AIR Mode”, then press .
6
Press
V/v repeatedly to select
the setting you want.
• Party: The S-AIR receiver outputs sound according to the input selected on the S-AIR main unit. However, if DVD is selected on S-AIR main unit, S-AIR receiver remains as the last selected input.
• Separate: You can select the input you want for the S-AIR receiver while the input of the S-AIR main unit remain unchanged.
7
Press GUI MODE.
The GUI menu turns off.
8
Select the desired function on the S-AIR receiver.
x When “Party” is set
The S-AIR receiver’s function changes sequentially as you press INPUT
SELECTOR +/– on the receiver or S-AIR
CH of the S-AIR receiver.
x When “Separate” is set
The S-AIR receiver’s function changes by pressing S-AIR CH of the S-AIR receiver.
Note
When TUNER (FM/AM band) is selected on the S-AIR main unit, you can only select the same band for the tuner on the S-AIR receiver.
However, you can select input other than
TUNER on the S-AIR receiver.
9
Adjust the volume on the S-AIR receiver.
Note
The sound of the S-AIR receiver may be cut off by operation of the S-AIR main unit.
To control the system from the
S-AIR receiver
You can control the system from the S-AIR receiver by using the following buttons.
Press
N
, X, x,
./>
S-AIR CH
Operation
Share the same operations on the remote
Change the function of the
S-AIR main unit
For details, refer to the operating instructions of the S-AIR receiver.
96
GB
Changing the channel for better sound transmission
If you use multiple wireless systems which sharing the 2.4 GHz band, such as wireless
LAN or Bluetooth, the transmission of S-AIR products or other wireless systems may be unstable. In this case, transmission may be improved by changing the “RF Change” setting.
2CH/
A.DIRECT
A.F.D.
RESOLUTION
INPUT
MODE
MOVIE MUSIC
SLEEP
NIGHT
MODE
DISPLAY GUI MODE
GUI MODE
V/v/b,
O
RETURN/
EXIT
HOME
MENU
.
< <
TOOLS/
OPTIONS
>
MENU
1
Press GUI MODE.
After “MENU ON” appears on the display for a while, “GUI” appears and the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not appear on the TV screen.
2
Press
V/v repeatedly to select
“Settings”, then press or
b.
The Settings menu list appears on the TV screen.
3
Press
V/v repeatedly to select
“S-AIR”, then press .
The S-AIR menu appears.
Note
When the S-AIR transmitter (not supplied) is not inserted into the S-AIR main unit, “S-AIR” cannot be selected.
4
Press
V/v repeatedly to select
“RF Change”, then press or
b.
5
Press
V/v repeatedly to select
the setting you want.
• AUTO: Normally select this. The system changes “RF Change” to “ON” or “OFF” automatically.
• ON: The system transmits sound by searching for a better channel for transmitting.
• OFF: The system transmits sound by fixing the channel for transmitting.
6
Press GUI MODE.
The GUI menu turns off.
7
When you set “RF Change” to
“OFF”, select the ID so that sound transmission is most stable.
Notes
• When the wireless transmitter is not inserted in the
S-AIR main unit, you cannot set “RF Change”.
• In most cases, you will not need to change this setting.
• If “RF Change” is set to “OFF”, transmission between the S-AIR main unit and S-AIR sub unit can be performed using one of the following channels.
– S-AIR ID A: equivalent channel for IEEE
802.11b/g channel 1
– S-AIR ID B: equivalent channel for IEEE
802.11b/g channel 6
– S-AIR ID C: equivalent channel for IEEE
802.11b/g channel 11
• The transmission may be improved by changing the transmission channel (frequency) of the other wireless system(s). For details, refer to the operating instructions of the other wireless system(s).
97
GB
Stabilizing S-AIR reception
Read the following when S-AIR reception is poor or unstable.
When S-AIR reception is poor
Check the following.
• Keep cords that are connected to the S-AIR product (AC power cord (mains lead), speaker cords, or other cords) away from the wireless adapter and slot.
• Adjust the location (height, orientation, and place in the room) of S-AIR products until reception is the most stable.
– Place so that the wireless adapters of the
S-AIR main unit and sub unit are closer.
?/1
PHONES SPEAKERS
MULTI CHANNEL DECODING
A.F.D.
MOVIE MUSIC INPUT MODE DIMMER DISPLAY
MASTER VOLUME
INPUT SELECTOR
MUTING
AUTO CAL MIC VIDEO
VIDEO 2 IN
L AUDIO R
– Place so that S-AIR products are separated from other wireless devices.
?/1
PHONES
MULTI CHANNEL DECODING
SPEAKERS
2 CH/
A.DIRECT
A.F.D.
MOVIE MUSIC INPUT MODE DIMMER DISPLAY
MASTER VOLUME
INPUT SELECTOR
MUTING
AUTO CAL MIC VIDEO
VIDEO 2 IN
L AUDIO R
• Keep as much space as possible around
S-AIR products.
– Avoid placing S-AIR products on top of or directly below other electronic equipment.
– Avoid placing S-AIR products in a closed rack, metal rack or under a table.
– Place so that S-AIR products are separated from metal doors or tables.
If you still cannot improve S-AIR reception,
change the “RF Change” setting (page 97).
98
GB
Enjoying the S-AIR receiver while the S-AIR main unit is in standby mode
(For the S-AIR receiver only (not supplied))
You can enjoy the S-AIR receiver while the
S-AIR main unit is in standby mode by setting
“S-AIR Stby” to “ON”.
2CH/
A.DIRECT
A.F.D.
RESOLUTION
INPUT
MODE
MOVIE MUSIC
SLEEP
NIGHT
MODE
DISPLAY GUI MODE
GUI MODE
V/v/b,
5
Press
V/v repeatedly to select
the setting you want.
• ON: You can enjoy the S-AIR receiver while the S-AIR main unit is in standby mode or turned on.
• OFF: You cannot enjoy the S-AIR receiver while the S-AIR main unit is in standby mode.
To exit the menu
Press MENU.
Notes
• When you set “S-AIR Stby” to “ON”, the power consumption increases during the standby mode.
• When the wireless transmitter is not inserted in the
S-AIR main unit, you cannot set “S-AIR Stby”.
• When the wireless transmitter is removed from the
S-AIR main unit, “S-AIR Stby” is set to “OFF” automatically.
• If you have selected TUNER (FM/AM band) on the S-AIR main unit before you turn it off and
“S-AIR Stby” is set to “ON”, you can only select the same band for the tuner on the S-AIR receiver.
However, you can select input other than TUNER on the S-AIR receiver.
• The sound of the S-AIR receiver may be cut off by operation of the S-AIR main unit.
O
RETURN/
EXIT
HOME
MENU
.
< <
TOOLS/
OPTIONS
>
MENU
1
Press GUI MODE.
After “MENU ON” appears on the display for a while, “GUI” appears and the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not appear on the TV screen.
2
Press
V/v repeatedly to select
“Settings”, then press or
b.
The Settings menu list appears on the TV screen.
3
Press
V/v repeatedly to select
“S-AIR”, then press .
The S-AIR menu appears.
Note
When the S-AIR transmitter (not supplied) is not inserted into the S-AIR main unit, “S-AIR” cannot be selected.
4
Press
V/v repeatedly to select
“S-AIR Stby”, then press .
99
GB

Public link updated
The public link to your chat has been updated.
Advertisement