Specifications. Exmark LAZER Z LZX940KC726, LAZER Z LZX980KC606, Laser Z LZZ29KA606, Laser Z LZZ38KC726, Laser Z LZZ27KC606, Laser Z LZZ24KA526, Laser Z LZZ34KA726, Laser Z LZZ23KC486, Laser Z LZZ29KCE606, Laser Z LZZ34KA606

Add to my manuals
64 Pages

advertisement

Specifications. Exmark LAZER Z LZX940KC726, LAZER Z LZX980KC606, Laser Z LZZ29KA606, Laser Z LZZ38KC726, Laser Z LZZ27KC606, Laser Z LZZ24KA526, Laser Z LZZ34KA726, Laser Z LZZ23KC486, Laser Z LZZ29KCE606, Laser Z LZZ34KA606 | Manualzz

Specifications

Specifications

Model Numbers

Serial Nos: 312,000,000 and Higher

LZX680KC486; LZX740KC526; LZX740KC606; LZX740KC606CA; LZX749EKC606; LZX801KA606;

LZX801KA606SS; LZX940KC606; LZX940KC726; LZX980KC606; LZX980KC726

Systems

Engine

• Engine Specifications: See your Engine Owner’s

Manual

• Engine Oil Type: Exmark 4–Cycle Premium

Engine Oil

• RPM: Full Speed: 3750 ±50 RPM (PTO not engaged) Idle: 1500 +100/-250 RPM

Fuel System

• Capacity: 12.0 gal. (45.4 L)

• Type of Fuel: Regular unleaded gasoline, 87 octane or higher; containing no more than 10% methanol or ethanol.

• Fuel Filter:

– Kohler:

Kohler P/N 24 050 13

– Kawasaki:

Kawasaki P/N 49019-7005

– Kohler EFI:

Kohler P/N 25 050 42

• Fuel Shut-Off Valve:

All Units: 1/4 turn increments (“ON”, “OFF”).

• Fuel level eight segment display — right hand control panel.

• Low fuel indicator light.

Electrical System

• Charging System: Flywheel Alternator

• Charging Capacity:

Kohler and Kawasaki: 15 amps

Kohler EFI: 20 amps

• Battery Type: BCI Group U1

• Recommended Minimum Battery CCA:

– Kohler 940 & 980 engines: 340 CCA

– All other engines: 260 CCA

• Battery Voltage: 12 Volt

• Low Voltage Light — RH control panel

• Polarity: Negative Ground

• Fuses:

All units:

– 25 amp main fuse

– 25 amp charging system fuse

– 10 amp PTO fuse

– 15 amp accessory fuse

Safety Interlock System

• LCD indicators appear for the PTO, park brake, drive levers, and operator presence in the message display on the RH control panel.

• PTO must be disengaged, brake engaged, and motion control levers out (neutral lock) to start engine. (It is not necessary for the operator to be in the seat to start the engine.)

• Operator must be in seat when PTO is engaged, brake is disengaged, or motion control levers are moved in or engine will stop.

• Engine will stop if either the left, the right, or both levers are moved from neutral lock position while brake is engaged.

Operator Controls

• Steering and Motion Control:

Note: Motion control levers are adjustable to two heights.

– Separate levers, on each side of the console, control speed and direction of travel of the respective drive wheels.

– Steering is controlled by varying the position of the levers relative to each other.

16

Specifications

– Moving motion control levers outward (in slots) locks the drive system in neutral.

• PTO Engagement Switch: Engages electric clutch

(to drive belt) which engages mower blades.

• Parking Brake Lever: Engages/Disengages parking brake.

• Deck Height Adjustment Lever: Sets cutting height to desired position.

• Deck Lift Pedal: Foot pedal that lifts deck.

• Transport Lock:

– Latching position: Automatically latches at the transport position.

– Unlatching position: Deck does not latch at the transport position.

Seat

• Type:

– For all units except LZX801KA606SS,

LZX940KC606, LZX940KC726,

LZX980KC606, LZX980KC726: Standard seat with high back, extra wide foam padded seat cushion with internal suspension, thick bolstering, two-tone cover, armrests, integral safety switch, and seat vibration isolation system.

Optional seat accessories for units with standard seats:

◊ Custom ride suspension system to enhance

Standard Seat. Adds approximately 3 inches (7.6 cm) to seat height.

◊ Deluxe suspension (adjustable spring suspension) seat with high back, armrests, and integral safety switch. Seat height remains the same.

– For LZX801KA606SS, LZX940KC606,

LZX940KC726, LZX980KC606,

LZX980KC726:

Deluxe suspension (adjustable spring suspension) seat with high back, armrests, and integral safety switch. Seat height remains the same.

• Mounting: Hinged seat frame to tilt up seat. Held in tilted position with prop rod. Adjustable fore and aft on seat tracks.

• Armrests:

– Standard seat: foam padded adjustable flip-up armrests.

– Suspension seat: molded adjustable flip-up armrests.

• Seat Safety Switch:

Integrated seat switch. Time delay seat switch eliminates rough ground cut-outs.

Hydrostatic Ground Drive System

• Two unitized hydrostatic transmissions:

– 48 and 52 inch decks:

◊ 12cc Parker axial piston pump

◊ 240cc Parker geroler motor

– 60 and 72 inch decks:

◊ 16cc Parker axial piston pump

◊ 280cc Ross geroler motor

• Hydraulic Oil Type: Exmark Premium Hydro Oil.

• Hydraulic Oil Capacity: 52 oz (1.5 L) per side

• Hydraulic Filter: P/N 116-0164

• Speeds:

– 12cc

◊ 0-10 mph (16.1 km/hr) forward.

◊ 0-5.5 mph (8.9 km/hr) reverse.

– 16cc

◊ 0-11.5 mph (18.5 km/hr) forward.

◊ 0-6 mph (9.7 km/hr) reverse.

• Drive wheel release valves allow machine to be moved when engine is not running.

17

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals