Operation. Exmark LAZER Z LZX940KC726, LAZER Z LZX980KC606, Laser Z LZZ29KA606, Laser Z LZZ38KC726, Laser Z LZZ27KC606, Laser Z LZZ24KA526, Laser Z LZZ34KA726, Laser Z LZZ23KC486, Laser Z LZZ29KCE606, Laser Z LZZ34KA606

Add to my manuals
64 Pages

advertisement

Operation. Exmark LAZER Z LZX940KC726, LAZER Z LZX980KC606, Laser Z LZZ29KA606, Laser Z LZZ38KC726, Laser Z LZZ27KC606, Laser Z LZZ24KA526, Laser Z LZZ34KA726, Laser Z LZZ23KC486, Laser Z LZZ29KCE606, Laser Z LZZ34KA606 | Manualzz

Operation

Note: Determine the left and right sides of the machine from the normal operating position.

Controls

Motion Control Levers

The motion control levers located on each side of the console control the forward and reverse motion of the machine.

Moving the levers forward or backward turns the wheel on the same side forward or reverse respectively. Wheel speed is proportional to the amount the lever is moved.

Moving the levers outward from the center position into the T-slot locks them in the neutral position

(Figure 5).

When the motion control levers are in the neutral position, the LCD indicator appears in the message

display on the RH console (see Figure 8).

Operation

Choke Control (All Units Except

Kohler EFI)

Located on right console (black lever) (see Figure 6).

The choke is used to aid in starting a cold engine.

Moving the choke lever forward will put the choke in the “ON” position and moving the choke lever to the rear, to the detent, will put the choke in the “OFF” position. Do Not run a warm engine with choke in the “ON” position.

1.

Fuses

2.

Message display

3.

Ignition switch

Figure 6

Right Console

4.

PTO engagement switch

5.

Throttle

6.

Choke

Figure 5

1.

Neutral lock position

(handles out)

2.

Neutral operate position

(handles in)

3.

Front of Unit

4.

Forward

5.

Neutral (operate)

6.

Reverse

21

Throttle Control

Located on right console (red lever) (see Figure 6).

The throttle is used to control engine speed. Moving the throttle lever forward will increase engine speed and moving the throttle lever to the rear will decrease engine speed. Moving the throttle forward into the detent is full throttle.

Brake Lever

Located on right side of unit, just to the front of the

RH motion control lever.

The brake lever engages a parking brake on the drive wheels.

Note: The LCD indicator appears in the message display on the RH console when the park brake is

engaged (see Figure 8).

Pull the lever up and rearward to engage the brake.

Operation

Push the lever forward and down to disengage the brake.

The unit must be tied down and brake engaged when transporting.

Ignition Switch

Located on right console (see Figure 6).

The ignition switch is used to start and stop the engine. The switch has three positions “OFF”, “ON” and “START”. Insert key into switch and rotate clockwise to the “ON” position. Rotate clockwise to the next position to engage the starter (key must be held against spring pressure in this position). Allow the key to return to the “on” position immediately after the engine starts.

Figure 8

1.

LCD Indicators

2.

Low fuel indicator light

3.

Fuel level bar display

4.

Low voltage indicator light

5.

Hour/Voltage display

1.

Off

2.

On

Figure 7

3.

Start

Note: Brake must be engaged, motion control levers out (neutral lock position) and PTO switch disengaged to start engine. (It is not necessary for the operator to be in the seat to start the engine.)

The hour meter is recording when the decimal point is flashing in Hour/Voltage display.

Hours are displayed when the key is off or when the machine is running.

Note: If the ignition key is turned to the “ON” position for a few seconds before cranking the engine, the battery voltage will display in the area where the hours are normally displayed.

Note: The LCD indicators appear when each control meets the “safe to start” mode (e.g. the indicator turns on when the operator is in the seat.)

Hour Meter

Located on the right console in the message display

(see Figure 6 and Figure 8).

The hour meter records the number of hours that the engine has run.

Fuel Shut-Off Valve

Located behind and below the seat.

The fuel shut-off valve is used to shut off the fuel when the machine will not be used for a few days, during transport to and from the jobsite, and when parked inside a building.

Align valve handle with the fuel line to open. Rotate

90° to close.

Fuel Gauge

Located on the right console in the message display

(see Figure 6 and Figure 8).

The fuel level is shown on a bar display. The indicator light appears when the fuel level is low (approximately one gallon remaining in the tank).

22

Operation

Drive Wheel Release Valves

WARNING

Hands may become entangled in the rotating drive components below the engine deck, which could result in serious injury or death.

Stop engine, remove key, allow all the moving parts to stop before accessing the drive wheel release valves.

WARNING

The engine and hydraulic drive units can become very hot. Touching a hot engine or hydraulic drive units can cause severe burns.

Allow the engine and hydraulic drive units to cool completely before accessing the drive wheel release valves.

Located on the back of the unitized hydraulic drive units, below the engine deck.

During normal operating conditions, the drive wheel release valves are positioned horizontally. If the machine has to be pushed by hand, the valves must

be in the “released” position (see Figure 9).

Note: The handle must be horizontal and against the stop for operation.

Do Not tow machine.

PTO Engagement Switch

Located on right console (see Figure 6).

Switch must be pulled out (up) to engage the blades.

Switch is pushed in to disengage the blades.

The LCD indicator will appear when the PTO switch

is disengaged (see Figure 8).

Low Voltage Indicator

Located on the right console in the message display

(see Figure 6 and Figure 8).

A low voltage condition (less than 12.3 volts) exists when the LCD indicator appears on the message display while the engine is running.

If the ignition key is turned to the “ON” position for a few seconds before cranking the engine, the battery voltage will display in the area where the hours are normally displayed.

Note: The indicator normally appears when the engine is off and the key switch is turned to the

“ON” position.

Figure 9

1.

Handle in “released” position

2.

Handle in “operating” position

To release the drive system (see item 1 in Figure 9),

rotate the handle 1/4 turn to the vertical position until it hits against the stop.

To reset the drive system (see item 2 in Figure 9),

rotate the handle 1/4 turn to the horizontal position until it hits against the stop.

Deck Lift Pedal

Located at the right front corner of the floor pan.

Push the pedal forward with your foot to raise the cutting deck. Allow the pedal to move rearward to lower the cutting deck to the cut height that has been set.

Transport Lock

Located on the height of cut adjustment plates to the right of the parking brake.

Position in the transport latching position to automatically latch the cutting deck when raised to

the transport position (see item 1 in Figure 10).

In the non-latching position, the deck will automatically return to the cutting height when the

pedal is lowered (see item 3 in Figure 10).

23

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals