Lubricate Deck Lift Pivot. Exmark LAZER Z LZX940KC726, LAZER Z LZX980KC606, Laser Z LZZ29KA606, Laser Z LZZ38KC726, Laser Z LZZ27KC606, Laser Z LZZ24KA526, Laser Z LZZ34KA726, Laser Z LZZ23KC486, Laser Z LZZ29KCE606, Laser Z LZZ34KA606

Add to my manuals
64 Pages

advertisement

Lubricate Deck Lift Pivot. Exmark LAZER Z LZX940KC726, LAZER Z LZX980KC606, Laser Z LZZ29KA606, Laser Z LZZ38KC726, Laser Z LZZ27KC606, Laser Z LZZ24KA526, Laser Z LZZ34KA726, Laser Z LZZ23KC486, Laser Z LZZ29KCE606, Laser Z LZZ34KA606 | Manualzz

Maintenance

13. Torque the nut to 75-80 in-lb (8-9 N-m), loosen, then re-torque to 20-25 in-lb (2-3 N-m). Make sure axle does not extend beyond either nut.

14. Reinstall the seal guards over the wheel hub and insert wheel into caster fork. Reinstall caster bolt and tighten nut fully.

Important: To prevent seal and bearing damage, check the bearing adjustment often. Spin the caster tire. The tire should not spin freely

(more than 1 or 2 revolutions) or have any side play. If the wheel spins freely, adjust torque on spacer nut until there is a slight amount of drag.

Reapply thread locking adhesive.

Replacement Filters

Kohler

Kawasaki

Kohler EFI

Kohler P/N 24 050 13

Kawasaki

P/N 49019-7005

Kohler P/N 25 050 42

Note: It is important to reinstall the fuel line hoses and secure with plastic ties the same as they were originally installed at the factory to keep the fuel line away from components that could cause fuel line damage.

Lubricate Deck Lift Pivot

Service Interval: Every 100 hours

1. Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2. Lubricate deck lift pivot with a spray type lubricant or light oil.

Check Spark Plugs

Service Interval: Every 200 hours

Remove spark plugs, check condition and reset gaps, or replace with new plugs. See Engine Owner's

Manual.

Change Fuel Filter

Service Interval: As required

A fuel filter is installed between the fuel tank and the engine. Replace when necessary.

For Kohler EFI Units:

WARNING

Fuel system components are under high pressure. The use of improper components can result in system failure, gasoline leakage and possible explosion.

Use only approved fuel lines and fuel filters for high pressure systems.

Change Hydraulic System

Filter and Fluid

Service Interval: After the first 250 hours

Every 500 hours thereafter

Note: Only use Exmark Hydro Filter–Part No.

116-0164 for summer or winter.

1. Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2. Raise the rear of machine up and support with jack stands (or equivalent support) just high enough to allow drive wheels to turn freely.

CAUTION

Raising the mower deck for service or maintenance relying solely on mechanical or hydraulic jacks could be dangerous. The mechanical or hydraulic jacks may not be enough support or may malfunction allowing the unit to fall, which could cause injury.

Do Not rely solely on mechanical or hydraulic jacks for support. Use adequate jack stands or equivalent support.

3. Remove the pump drive belt.

4. Place a catch pan under the hydro.

5. Carefully clean area around the filters. It is important that no dirt or contamination enter the hydraulic system.

6. Using a socket, unscrew filters to remove and allow oil to drain.

7. Before installing the new filters, apply a thin coat of Exmark Premium Hydro Oil on the surface of the two rubber seals.

38

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals