Copper-Based Anti-seize. Exmark LAZER Z LZX940KC726, LAZER Z LZX980KC606, Laser Z LZZ29KA606, Laser Z LZZ38KC726, Laser Z LZZ27KC606, Laser Z LZZ24KA526, Laser Z LZZ34KA726, Laser Z LZZ23KC486, Laser Z LZZ29KCE606, Laser Z LZZ34KA606

Add to my manuals
64 Pages

advertisement

Copper-Based Anti-seize. Exmark LAZER Z LZX940KC726, LAZER Z LZX980KC606, Laser Z LZZ29KA606, Laser Z LZZ38KC726, Laser Z LZZ27KC606, Laser Z LZZ24KA526, Laser Z LZZ34KA726, Laser Z LZZ23KC486, Laser Z LZZ29KCE606, Laser Z LZZ34KA606 | Manualzz

Maintenance

• Between the spindles and sheaves.

• Under top cutter housing bearing guard.

Copper-Based Anti-seize

Copper-based anti-seize is used in the following location:

On threads of Blade Bolts. See Check Mower

Blades section.

Dielectric Grease

Dielectric grease is used on all blade type electrical connections to prevent corrosion and loss of contact.

Dielectric grease should not be applied to sealed connectors.

Adjustments

Note: Disengage PTO, shut off engine, wait for all moving parts to stop, engage parking brake, and remove key before servicing, cleaning, or making any adjustments to the unit.

CAUTION

Raising the mower deck for service or maintenance relying solely on mechanical or hydraulic jacks could be dangerous. The mechanical or hydraulic jacks may not be enough support or may malfunction allowing the unit to fall, which could cause injury.

Do Not rely solely on mechanical or hydraulic jacks for support. Use adequate jack stands or equivalent support.

Deck Leveling

1. Position the mower on a flat surface.

2. Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

3. Check the tire pressure in the drive tires. Proper inflation pressure for tires is 13 psi (90 kPa).

Adjust if necessary.

4. Position the transport lock in the latching position.

5. Push the foot pedal all the way forward and the deck will latch at the 5 1/2 inch (14 cm) transport

position (Figure 27).

40

Maintenance

1.

Foot lever

2.

Height of cut pin

Figure 27

3.

Transport lock

1.

3 1/4 inches (8.3 cm)

2.

Back blade tip

3.

Front blade tip

Figure 28

4.

3 inches (7.6 cm)

5.

Level surface

6. Insert the height adjustment pin into the 3 inch

(7.6 cm) cutting height location.

7. Release the transport lock and allow the deck to lower to the cutting height.

8. Raise the discharge deflector.

9. Measure from the level surface to the front tip of the center blade. The measurement should read

3 inches (7.6 cm).

Note: In most conditions, the back blade tip should be adjusted 1/4 inch (6.4 mm) higher than the front.

10. Loosen the jam nuts on the top of each deck link. Fine tune the adjuster on the front deck lift assembly by turning it to get 3 inch (7.6 cm)

height (see Figure 29).

To increase the height, turn the adjuster clockwise; to decrease, turn counterclockwise.

41

1.

Adjuster link

2.

Jam nut

Figure 29

3.

Adjuster

11. The back tip of the blade should measure 3

1/4 inches (8.3 cm). Fine tune rear adjusters as required.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals