GAME SPECIFICATIONS AND INSTALLATION
GAME SPECIFICATIONS AND INSTALLATION
SPECIFICATIONS
THIS GAME IS SUITABLE FOR INDOOR USE ONLY.
Height: 86" upright
Weight: 200 lbs.
Width: 24"
Voltage: 95-135V 60Hz
NOTE: A working area of approximately 6 ft. x 4 ft. with a 90 inch ceiling clearance is needed to install this game.
INSTALLATION
1)
2)
3)
4)
5)
6)
Unlock and open door “A” (see Figure 1) to access the electronics compartment.
Remove the washers and bolts “C” from the cashbox and set them aside within easy reach.
Slowly and carefully swing the upper section of the game upright, bracing the back until the game is securely fastened (step 4).
Verify that the wires are not pinched. Place the bolts “C” in the inside top of the electronics compartment and thread upward through holes “B” to secure the upper section of the game. Tighten the bolts.
This game is equipped with an easily replaceable power/line cord which is located inside the pedestal when shipped and must be routed through the opening at the back of the game prior to operation. Review top figure on page 12 before proceeding. a) Open coin door. b) c) d) e)
Turn power cord cover latch counterclockwise until the power cord hole cover itself can be rotated counterclockwise. (See lower left figure on page 12.)
Turn power cord hole cover to expose opening. (See lower right figure on page 12.)
Locate power cord (inside pedestal) and route plug end through opening.
Push the entire length of the cord through the opening.
If the cabinet top must be folded down for any reason, the power cord must be placed back inside the pedestal.
Move the game to its operation location without tilting it more than 10 degrees.
Plug power cord into an appropriate outlet.
CAUTION
To ensure safety, it is recommended that the game be secured to the floor
or to the wall using the Stability Assurance Kit provided. See instructions
on the following pages.
Valley Cougar 8
10
Cougar 8 Manual
MODEL EL-A-AA-EN8
GAME SPECIFICATIONS AND INSTALLATION
Cougar 8 Manual
Figure 2. Cougar 8 Full front view
11
GAME SPECIFICATIONS AND INSTALLATION
LINE CORD ROUTING FIGURES
12
Figure 3. Line cord routing figures
Cougar 8 Manual
STABILITY ASSURANCE KIT
(Shipped in Cash Box)
Parts List
GAME SPECIFICATIONS AND INSTALLATION
Figure 4. Stability Assurance Kit
Installation Instructions
Tools Needed
- Measuring tape
- Small screwdriver (Phillips and Flathead)
- Pliers or Crescent wrench
- Drill with:
12.5mm (1/2") bit to secure the game to a hollow wall.
12.5mm (1/2") masonry bit to secure the game to a concrete, brick, or stone wall.
Attachment of the chain to the wall
Step 1: Fasten eye bolt and chain to the game
• Screw the eye bolt with chain (D) into the insert on the upper back wall of the game.
Cougar 8 Manual
13
GAME SPECIFICATIONS AND INSTALLATION
Step 2: Fasten to the wall according to the following instructions A, B, or C
A. Hollow wall: plaster, drywall, etc.
1. With the game in the position where it will be played, mark a spot on the wall directly in line with the eye bolt and chain attachment on the back of the game.
2 Drill a 12.5mm (1/2") diameter hole at the marked spot.
3. Unscrew the wings from the toggle bolt (H).
4. Place a flat washer (N) on the toggle bolt.
5. Place the toggle bolt (H) through a loop in the chain a few inches from the end of the chain.
The toggle bolt (H) may have to be threaded through the loop in the chain.
6. Slide a fender washer (R) on the toggle bolt (H) and screw the wings back on.
7. Push the toggle bolt (H) into the drilled hole in the wall.
8. Fasten the toggle bolt (H) tightly until the wings are snug against the back of the wall as shown. Keep the chain as taut as possible to minimize slack.
Figure 5. Eye bolt and chain fastened to game
Figure 6. Fasten to hollow wall, plaster, drywall, etc.
Figure 7. Close-up toggle bolt
14
Cougar 8 Manual
GAME SPECIFICATIONS AND INSTALLATION
B. Concrete, brick, stone wall
1. With the game in the position where it will be played, mark a spot on the wall directly in line with the eye bolt and chain attachment on the back of the game.
2. Drill a 12.5mm (1/2") diameter hole, 35mm (1-1/4") deep at the marked spot.
3. Pound the wall anchor (K) into the hole until it is flush with the wall surface.
4. Screw the eye bolt (J) into the wall anchor (K) until it is tight.
5. Thread the chain through the eye bolt and attach it to itself with the screw (E) and the two hex nuts (F) as shown.
Keep the chain as taut as possible to minimize slack.
Figure 8. Fasten to concrete, brick, stone wall
Figure 9. Close-up Hex nuts
C. Wood stud mounting
1. With the game in the position where it will be played, mark a spot on the wall directly in line with the eye bolt and chain attachment on the back of the game.
2. Screw the eye bolt into the stud at the marked spot.
3. Thread the chain through the eye bolt and attach it to itself with the screw ( E) and the two hex nuts (F) as shown. Keep the chain as taut as possible to minimize slack.
Figure 10. Wood stud mounting
Cougar 8 Manual
15
GAME SPECIFICATIONS AND INSTALLATION
Attachment to the floor
Fasten to floor according to instructions A or B.
Concrete floor
1. Mark two spots on the floor according to the diagram.
2. Drill the two holes at the marked spots
12.5mm (1/2") diameter X 45mm (1-3/4") deep each.
3. Pound in the floor anchors (P).
4. Align the holes in the base of the game with floor anchors (P).
5. Secure the game with the flat washers (N) and lag bolts (M).
6. Tighten the lag bolts until flush with the bottom of the counterbored holes in the base.
Wood floor
1. Position the game in its selected location.
2. Secure the game with the washers (N) and lag bolts (M).
Figure 11. Fasten to a concrete and wood floor
NOTE: If desired, a 6mm (1/8") diameter pilot hole may be used to start the lag bolt.
3. Tighten the lag bolts (M) until flush with the bottom of the counterbored holes in the base.
16
Cougar 8 Manual
