- No category
advertisement
3. Scale Fidelity (Log)
3. Scale Fidelity
(Log)
Specification
5 *l.O dB max. over 0 to 80 dB display
< f 1.5 dB max. over 0 to 90 dB display
Related Performance
Amplitude Fidelity Test
Test
Description
The specification listed is for cumulative error. Only cumulative error is measured in this procedure.
A signal source of known amplitude is connected to the spectrum analyzer and the analyzer is adjusted for a reference. The signal source is stepped down in 1 dB steps and the displayed signal amplitude on the spectrum analyzer measured at each step. This measurement is performed in both the 3 kHz and 300 kHz bandwidths.
Operation Verification 5-13
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 Certification
- 3 Warranty
- 4 Assistance
- 4 Safety Notes
- 5 General Safety Considerations
- 6 How to Use This Guide
- 6 HP 8568B Documentation Description
- 6 HP 8568B Installation and Verification Manual
- 6 HP 8568B Operating and Programming Manual
- 6 HP 8568B Performance Tests and Adjustments Manual
- 6 HP 85680B RF Section Troubleshooting and Repair Manual
- 6 HP 85662A IF-Display Section Troubleshooting and Repair Manual
- 13 What You'll Find in This Chapter
- 14 Introducing the HP 8568B
- 14 Safety
- 14 Accessories Supplied
- 17 Accessories Available
- 18 Options
- 19 Instruments Covered by This Manual
- 21 Calibration Cycle
- 21 HP-IB Address Selection
- 21 Bench Operation
- 22 Electrostatic Discharge Information
- 23 Static-Safe Accessories
- 24 Routine Maintenance
- 24 Cleaning the Display
- 25 Cleaning the RF Section's Fan Filter
- 25 Replacing the RF Section's Battery
- 30 Ordering Information
- 30 Direct Mail Order System
- 30 Direct Phone-Order System
- 31 Returning the Instrument for Service
- 31 Service Tags
- 31 Original Packaging
- 33 Other Packaging
- 35 Sales and Service Offices
- 36 What You'll Find in This Chapter
- 36 Safety
- 38 Preparation for Use
- 38 Initial Inspection
- 38 Operating Environment
- 38 Power Requirements
- 39 To Install Standard Instruments
- 42 To Install Option 908 and 913 Instruments
- 48 To Install Option 010 Instruments
- 55 To Set the HP-IB Address
- 55 From the Front Panel
- 55 From the HP-IB Bus
- 55 From the HP-IB Address Switch
- 61 Introduction
- 61 Frequency
- 61 Measurement Range
- 61 Displayed Values
- 61 Center Frequency
- 62 Frequency Span
- 63 Frequency Count
- 63 Resolution
- 65 Stability
- 65 Spectral Purity
- 66 Amplitude
- 66 Measurement Range
- 66 Displayed Values
- 67 Reference Lines Accuracy
- 67 Dynamic Range
- 69 Amplitude Uncertainty
- 72 Marker
- 72 Sweep
- 73 Inputs
- 73 INPUT #1
- 73 INPUT #2
- 74 Outputs
- 74 CAL OUTPUT
- 74 1ST LO OUTPUT
- 74 Options
- 74 75 Ohm Input Impedance, Option 001
- 75 400 Hz Power Line Frequency Operation, Option 400
- 76 General
- 76 HP-IB Interface Functions
- 76 Environmental
- 76 Power Requirements
- 76 Humidity
- 76 EMI
- 76 X-Rays
- 78 Warm-Up Time
- 78 Weight
- 79 Dimensions
- 80 Frequency
- 80 Resolution
- 81 Stability
- 81 Spectral Purity
- 82 Amplitude
- 82 Average Noise Level
- 82 Log to Linear Switching
- 82 Frequency Response (Flatness) Uncertainty
- 83 Residual Responses
- 83 Third Order Intermodulation Distortion
- 84 Inputs
- 84 RF INPUTS
- 84 VIDEO INP
- 84 IF INP
- 84 EXT TRIGGER
- 85 FREQ REFERENCE (IN)
- 85 Outputs
- 85 Display Outputs
- 85 Recorder Outputs
- 85 SWEEP
- 86 VIDEO
- 86 PENLIFT
- 86 2 1.4 MHz IF OUTPUT
- 86 FREQ REFERENCE (OUT)
- 86 VIDEO OUT
- 87 IF OUT
- 87 PROBE POWER (front panel)
- 87 General
- 87 Acoustic Noise Emission/Geraeuschemession
- 88 Function Descriptions
- 88 Sweep
- 90 What You'll Find in This Chapter
- 94 Test System Configuration
- 94 Equipment Connections
- 96 Program Loading
- 96 Program Operation
- 98 HP-IB Addresses
- 99 Error Messages
- 99 Test Descriptions
- 100 1. Input Attenuator Switching Uncertainty
- 101 2. IF Gain Uncertainty
- 102 3. Scale Fidelity (Log)
- 103 4. Scale Fidelity (Linear)
- 104 5. Log Scale Switching Uncertainty
- 105 6. Resolution Bandwidths
- 106 7. Impulse and Resolution Bandwidths (Opt. 462 Impulse Bandwidth)
- 107 8. Line Related Sidebands
- 108 9. Residual FM
- 109 10. RF Gain Uncertainty
- 110 11. Sweep Time Accuracy
- 111 12. Average Noise Level
- 112 13. Residual Responses
- 113 14. Frequency Span Accuracy
- 114 15. Frequency Response
- 115 16. Second Harmonic Distortion
- 116 17. Third Order Intermodulation Distortion
- 117 18. Calibrator Output Amplitude Accuracy