Specifications. Exmark PIONEER PNS20KA443, PIONEER PNS22KA483, PIONEER PNS24KA523, PIONEER S-SERIES Operators


Add to my manuals
52 Pages

advertisement

Specifications. Exmark PIONEER PNS20KA443, PIONEER PNS22KA483, PIONEER PNS24KA523, PIONEER S-SERIES Operators | Manualzz

Specifications

Specifications

Model Numbers

Serial Nos: 315,000,000 and Higher

PNE651GKA48200; PNE691GKA52200; PNE710GKC48200; PNE720GKC52200

Systems

Engine

• Engine Specifications: See your Engine Owner’s

Manual

• Engine Oil Type: Exmark 4–Cycle Premium

Engine Oil

• RPM: Full Speed: 3600 ±50 RPM (PTO not engaged) Idle: 1500 ±100 RPM

Fuel System

• Capacity: 7.0 gal. (26.5 L)

• Fuel Recommendations:

– For best results, use only clean, fresh, unleaded gasoline with an octane rating of 87 or higher

((R+M)/2 rating method).

– Oxygenated fuel with up to 10% ethanol or

15% MTBE by volume is acceptable.

Do Not use ethanol blends of gasoline (such as E15 or E85) with more than 10% ethanol by volume. Performance problems and/or engine damage may result which may not be covered under warranty.

Do Not use gasoline containing methanol.

Do Not store fuel either in the fuel tank or fuel containers over the winter unless a fuel stabilizer is used.

Do Not add oil to gasoline.

• Fuel Filter:

Kohler: Kohler P/N 24 050 13

Kawasaki: Kawasaki P/N 49019-0014

• Fuel Shut-Off Valve:

All Units: 1/4 turn (“ON”, “OFF”).

Electrical System

• Charging System: Flywheel Alternator

• Charging Capacity: 15 amps

• Battery Type: BCI Group U1

• Recommended Minimum Battery CCA: 260 CCA

• Battery Voltage: 12 Volt

• Polarity: Negative Ground

• Fuses:

All units:

– 25 amp main fuse

– 20 amp charging system fuse

– 10 amp PTO fuse

– 15 amp accessory fuse

Safety Interlock System

• LCD indicators appear for the PTO, park brake, drive levers, and operator presence in the message display on the RH control panel.

• PTO must be disengaged, brake engaged, and motion control levers out (neutral lock) to start engine. (It is not necessary for the operator to be in the seat to start the engine.)

• Operator must be in seat when PTO is engaged, brake is disengaged, or motion control levers are moved in or engine will stop.

• Engine will stop if either the left, the right, or both levers are moved from neutral lock position while brake is engaged.

Operator Controls

• Steering and Motion Control:

Note: Motion control levers are adjustable to three heights.

– Separate levers, on each side of the console, control speed and direction of travel of the respective drive wheels.

– Steering is controlled by varying the position of the levers relative to each other.

– Moving motion control levers outward (in slots) locks the drive system in neutral.

16

Specifications

• PTO Engagement Switch: Engages electric clutch

(to drive belt) which engages mower blades.

• Parking Brake Lever: Engages parking brake.

• Deck Height Adjustment Lever: Sets cutting height to desired position.

• Deck Lift Pedal: Foot pedal that lifts deck.

• Transport Lock: Latching position: Automatically latches at the transport position.

Tires & Wheels

Quantity

Tread

Size

Ply Rating

Pressure

2

Drive

Pneumatic (Air filled)

Front Caster

Pneumatic (Air filled)

2

Super Turf

20 x 8.00-10

Smooth

13 x 5.00-6

4

2

13 psi (90 kPa) 13 psi (90 kPa)

Seat

• Type: Standard seat with foam padded seat cushion with armrests and integral safety switch.

Optional seat: Seat with high back, extra wide foam padded seat cushion with internal suspension, thick bolstering, two-tone cover, armrests, integral safety switch, and seat vibration isolation system.

Optional seat accessories for units with standard seats: Deluxe suspension seat with high back,

(dampened, adjustable spring suspension), armrests, and integral safety switch. Adds approximately 1/2 inch (1.3 cm) to seat height.

• Mounting: Hinged seat frame to tilt up seat. Held in tilted position with cable. Adjustable fore and aft on seat tracks.

• Armrests: Molded flip-up armrests.

• Seat Safety Switch:

Integrated seat switch. Time delay seat switch eliminates rough ground cut-outs.

Hydrostatic Ground Drive System

• Two unitized hydrostatic transmissions:

Hydro Gear ZT2800

• Hydraulic Oil Type: Exmark Premium Hydro Oil.

• Hydraulic Oil Capacity: 77 oz (2.3 L) per side

• Hydraulic Filter: P/N 109-3321

• Speeds:

– 0-7 mph (11.3 km/hr) forward.

– 0-4 mph (6.4 km/hr) reverse.

• Drive wheel release valves allow machine to be moved when engine is not running.

Cutting Deck

• Cutting Width:

– 48 inch Deck: (121.9 cm)

– 52 inch Deck: (132.1 cm)

• Discharge: Side

• Blade Size: (3 ea.)

– 48 inch Deck: 16.25 inches (41.3 cm)

– 52 inch Deck: 18.00 inches (45.7 cm)

• Blade Spindles: Solid steel spindles with .67 inch

(17 mm) I.D. bearings.

• Deck Drive: “B” Section belt with self-tensioning idler.

• Electric clutch: 125 ft-lb Mag Stop

• Deck: Full floating deck is attached to out-front support frame. Anti-scalp rollers provide maximum turf protection. Deck design allows for bagging, mulching or side discharge.

– 48 inch Deck: 3 anti-scalp rollers

– 52 inch Deck: 3 anti-scalp rollers

• Deck Depth:

– 48 inch Deck: 4.0 inches (10 cm)

– 52 inch Deck: 4.0 inches (10 cm)

• Cutting Height Adjustment:

Foot activated lever is used to adjust the cutting height from 1 1/2 inch (3.8 cm) to 5 inches (12.7

cm) in 1/4 inch (6.4 mm) increments.

• Mulching Kit: Optional.

17

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals