- No category
advertisement
Operation
Barrier Film
2
Contamination of the ScanX Swift
Use a new Barrier Film for each patient.
13.4 Single Plate Processing Scanner Preparation
Apply a barrier film to the ScanX Swift input guide making sure to align the opening in the film center with the slot of the inlet guide.
See Figure 13-2.
Figure 13-2.
Applying barrier film
Loss of image data
Image data on the plate will be lost when exposed to light. Transfer the PSP from the Barrier Envelope to the Plate Guide slot quickly. Always keep the sensitive side away from any light source to minimize image loss.
Make sure that the user-supplied imaging software is set to scan, the green control LED on the scanner is lit and the Swift Barrier Film is applied
13.5 Feeding Single Plates.
Refer to Figure 13-3 and process a single plate as follows.
1. Disinfect and Dry the Barrier Envelope (with plate still inside).
2. Hold the plate above the inlet guide with the printed side facing you and the notch of the envelope on the bottom as shown.
3. Tear the envelope lengthwise starting at the bottom notch while lowering the plate into the inlet guide.
4. Press the plate all the way down until the unit takes over and moves the plate on its own.
5. Remove and discard the envelope. The plate will drop into the bottom outlet pad when processing is completed.
6. View and save each scanned image using the user-supplied imaging software.
View A View B
Air Techniques, Inc.
View C
View D
Figure 13-3. Single Plate Feeding and Scanning
Page 19
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 1. General
- 4 General Notes
- 4 Equipment Disposal
- 4 Medical Device
- 4 Correct Usage
- 5 Incorrect Usage
- 5 Using Plates and Barrier Envelopes
- 5 Using Software
- 5 2. Safety
- 5 General Safety Notes
- 5 Electrical Safety Instructions
- 6 3. Warnings and Symbols
- 6 Instruction Manual
- 6 ScanX Swift
- 7 4. Delivery Contents
- 7 System Components
- 7 Unpacking and Inspection
- 8 5. Functional System Description
- 8 6. Functional Layout
- 9 Controls and Indicators
- 10 7. Computer System Requirements
- 10 Computer System Required Components
- 10 Recommended Components
- 11 System Properties
- 11 8. Set-up
- 11 Room for Set-up
- 11 Counter/Table Top Set-up
- 11 Monitor
- 12 9. Software Installation
- 12 10. ScanX Swift Connection Procedure
- 14 11. Barrier Envelope
- 14 11.1 Barrier Envelope Use
- 14 11.2 Barrier Envelope Handling
- 14 12. Plates
- 14 12.1 General
- 15 12.2 Working with Plates
- 15 12.3 Storing Plates
- 16 12.4 Cleaning Phosphor Storage Plates
- 16 12.5 Disinfecting the Phosphor Storage Plates
- 16 12.6 Disposal of Phosphor Storage Plates
- 16 12.7 Preparing Intraoral Plates for Patient Use
- 17 12.8 Take an X-ray Image
- 17 13. Plate Scanning with Swift
- 17 13.1 Changing the Inlet Guide
- 18 13.2 Scanner Start Up
- 18 13.3 Scanner Plate Processing Options
- 19 13.4 Single Plate Scanner Processing Preparation
- 19 13.5 Feeding Single Plates
- 20 13.6 Preparing Multiple Exposed Plates for Batch Scanner Processing
- 21 13.7 Scanning Multiple Plates
- 21 13.8 Erasing the Image Data
- 22 14. Disinfection and cleaning
- 22 15. Maintenance
- 22 15.1 Yearly Scheduled Maintenance
- 22 15.2 Phosphor Storage Plates
- 23 16. Technical Data
- 23 16.1 Scanx Swift Power Unit Electrical Details
- 23 16.2 Ambient Conditions
- 24 17. Troubleshooting
- 26 18. Device Shutdown And Storage
- 26 18.1 Powering Down System
- 26 18.2 Protective Dust Cover Installation
- 26 19. Replacement and Accessory Parts
- 26 19.1 Replacement Parts
- 26 19.2 Accessory and Consumable Parts
- 27 19.3 Transfer Storage Box
- 27 19.4 Intraoral Phosphor Storage Plates
- 27 19.5 Barrier Envelopes and PSP Cleaning Wipes
- 27 19.6 VISIX Imaging Software, 5 licenses, order number
- 28 A-1. Scanning Times
- 28 A-2. File Size (uncompressed)