RemotEye III User Manual – 6233-005

Add to my manuals
167 Pages

advertisement

RemotEye III User Manual – 6233-005 | Manualzz

Table of Contents

About This Manual ..............................................................................................................2

Contacting TOSHIBA’s Customer Support Center .........................................................3

Important Notice ..................................................................................................................4

Important Safety Instructions ............................................................................................4

General Safety Instructions ................................................................................................5

Safety Alert Symbol ........................................................................................................................................5

Special Symbols .............................................................................................................................................6

Equipment Warning Labels ...........................................................................................................................6

Installation Precautions ................................................................................................................................7

Introduction ..........................................................................................................................10

Package Contents ..........................................................................................................................................10

Features .........................................................................................................................................................11

Installation ............................................................................................................................15

System Compatibility .....................................................................................................................................16

Installing RemotEye III ..................................................................................................................................16

Making the Network Connection ...................................................................................................................18

Configuration ................................................................................................................................................19

Configuring via Terminal ..............................................................................................................................21

RemotEye III Configuration Menu Navigation ..............................................................................................23

Configuring the RemotEye III via Telnet .......................................................................................................36

Connecting to the RemotEye III via Telnet ....................................................................................................37

RemotEye III Telnet Menu Navigation ..........................................................................................................37

Configuring the RemotEye III via HTTP .......................................................................................................38

Connecting to the RemotEye III via HTTP ...................................................................................................40

RemotEye III Web Menu Navigation .............................................................................................................41

UPS Monitoring .............................................................................................................................................41

UPS Management ..........................................................................................................................................61

Email Notification..........................................................................................................................................71

EMD (Environmental Monitoring Device) ....................................................................................................73

RemotEye III Management ............................................................................................................................77

History Data & Logs .....................................................................................................................................83

Configuring the Remoteye III via SNMP ..........................................................................95

Connecting to the RemotEye III via SNMP ...................................................................................................100

Connecting to the RemotEye III via MODBUS..............................................................................................102

8 RemotEye III User Manual – 62330-005

Toshiba RemotEye Application Programs ........................................................................103

Toshiba RemotEye Client Software ...............................................................................................................103

Auto Save-Log Software ................................................................................................................................113

Tupgrade Firmware Tool ..............................................................................................................................117

RemotEye III Specifications................................................................................................119

RemotEye III Feature Summary ....................................................................................................................119

System Specifications .....................................................................................................................................120

Firmware Specifications ................................................................................................................................120

LED Key ........................................................................................................................................................121

Jumper Setting ...............................................................................................................................................122

DIP Switch Setting .........................................................................................................................................123

LAN connector (J2) .......................................................................................................................................123

Console connector (J3) ..................................................................................................................................123

Gold Finger GF1 ...........................................................................................................................................124

Appendix A: Install RemotEye Client Shutdown Software on VMware ESXi 5 ..........125

Software Needed ............................................................................................................................................125

Setup Procedure for RemotEye ESXi Client Shutdown Daemon* .................................................................126

Appendix B – Modbus Registers ........................................................................................132

Modbus Input Register for 1600XP: MONITORING ...................................................................................132

Modbus Input Coil for 1600XP: ALARMS and STATUS ..............................................................................143

Modbus Input Register for 4200FA/4300: MONITORING ..........................................................................151

Modbus Input Coil for 4200FA/4300: ALARMS and STATUS .....................................................................161

RemotEye III User Manual – 62330-005 9

Introduction

Congratulations on the purchase of your new Toshiba Uninterruptible Power Supply (UPS) system remote management tool: the RemotEye III! The RemotEye III supplies a 10/100 base-T network card that allows network administrators to monitor and control Toshiba UPS systems remotely via Simple Network Management Protocol

(SNMP), Modbus TCP, and Hypertext Transfer Protocol (HTTP) methods.

This user manual describes the configuration and operation of the RemotEye III. The RemotEye III is a circuit board that is inserted into the option slot of the UPS. The circuit board is connected to the UPS via the RemotEye III card edge connector.

Package Contents

Listed below are the items included in the RemotEye III package:

1. The RemotEye III printed circuit board.

2. PC cable, a DB9 female to RJ45 cable (Workstation COM port to RemotEye III COM port).

3. A CD-ROM containing the following: a. The RemotEye III Quick Installation Guide. b. RemotEye III User Manual c. 1600XP Mib File d. 4200FA/4300 Mib File e. RemotEye III Firmware Upgrade Utility Software Tool f. Shutdown Clients Software g. Auto-Save Log Utility Software Tool

Figure 1: RemotEye III Circuit Card

10 RemotEye III User Manual – 62330-005

Features

The RemotEye III has several support options for managing your Toshiba UPS.

HTTP Web Access

Allow access data from RemotEye III publicly or privately using a web browser. Web access includes Secure Sockets

Layer (SSL) Configurations (See Figure 2: HTTP Web Access Example).

Figure 2: HTTP Web Access Example

SNMP Access

RemotEye III provides enhanced SNMP security with option of SNMPv3, default protocol is SNMPv1. It is compatible with the United States Standard UPS MIB, RFC1628, and Japanese Standard UPS MIB (See SNMP

example using iReasoning MIB Browser Software in Figure 3: SNMP Access Example).

Figure 3: SNMP Access Example

Serial Communication (RS232), Terminal Access

RemotEye III User Manual – 62330-005 11

Allow access RemotEye III configuration settings through a Terminal Emulator Software for example,

HyperTermnianl or Tera Term (See Figure 4: Serial Communication Example).

Figure 4: Serial Communication Example

Telnet, Terminal Access

Allow access to RemotEye III configuration settings through Telnet which includes Secure Shell (SSH) protocol.

This can be done using a Terminal Emulator Software such us HyperTerminal or Tera Term (See Figure 5: Telnet

Access Example).

Additional Features:

12

Figure 5: Telnet Access Example

RemotEye III User Manual – 62330-005

BOOTP/DHCP Requests

The RemotEye III can automatically retrieve its network identity, IP address, from a network server using the Boot

Protocol (BOOTP) or Dynamic Host Configuration Protocol (DHCP).

Real-Time Clock (RTC)

The RemotEye III contains its own RTC which is used for time-stamping data logs and for executing any scheduled events.

UPS Event Notification

The RemotEye III can send out notification of UPS events via Email or SNMP Traps.

UPS Event Notification Filtering

The administrator has the ability to configure which event notifications to receive via Email or SNMP Traps, and which to filter out. NOTE: When configuring the filtering settings, it will affect both Email notifications and SNMP

Traps.

Graphic User Interface (GUI)

User-friendly GUI on the web interface pages and Java applets.

Power Quality Monitor

Java applets provide an on-screen visual indication of power quality through its dynamic graphics (See Figure 6: Java

Applet Example).

Figure 6: Java Applet Example

Versatile Remote UPS Management

Allow monitoring and management of Toshiba UPS via SNMP and HTTP (Web Interface) communication protocols.

Versatile UPS Configuration

RemotEye III has the ability to set the UPS parameters from any SNMP management station or through internet web browsers using HTTP protocol.

Data Log Retention

RemotEye III stores history file containing UPS power events, power quality, UPS status, and battery condition in its non-volatile memory.

Automatic UPS Shutdown

RemotEye III User Manual – 62330-005 13

The RemotEye III provides unattended and on-demand UPS shutdown; either pre-programmed or when the UPS reports a low battery condition, input power failure, overload condition, overheating condition, weekly schedule, special events, and EMD (Environmental Monitoring Device) sold separately, triggered events. NOTE: this feature only available for the 1600XP.

RADIUS Authenication

Allows the RemotEye III to work with a centralized RADIUS server before allowing the user to access monitor or manage the Toshiba UPS.

Additional Software Applicaitons:

Network Firmware Upgrade Tool

RemotEye III Firmware Upgrade Utility is an easy to use network upgrade utility tool that allows user to upgrade to a newer firmware version when available.

Auto Save Log Tool

RemotEye III Save (Auto) Log Application Program is an easy to configure utility tool that allows administrators to automatically save history logs from one to multiple RemotEye IIIs at the same time to a computer’s hard drive.

Toshiba Client Shutdown Software

RemotEye III Windows Clients Shutdown Program is software that is installed onto the client’s computer system.

This allows the RemotEye III to communicate with the Client Software to broadcast system failure messages via an

IP (Internet Protocol) packet and to perform unattended graceful shutdown of up to 250 clients operating under a variety of platforms.

RemotEye III Add-Ons:

Environmental Monitoring Device (EMD) (Sold Separately)

The EMD gives the ability for the RemotEye III to monitor environmental temperature and humidity. It also provides two dry contact closures, which can be used with our RemotEye Sensor Pack (sold separately), that can be set for normally open, normally closed, active high, or active low conditions. When an EMD event is triggered the

RemotEye III can send an email notification and SNMP Trap with the description of the event (See Figure 7: EMD

Module).

Figure 7: EMD Module

RemotEye Sensor Pack for EMD (Sold Separately)

14 RemotEye III User Manual – 62330-005

This sensor package extends the EMD monitoring capabilities (See Figure 8: EMD Sensor Pack). The sensor package

consists of the following:

1. Intrusion Sensor

2. Vibration Sensor

3. Water Sensor

4. Smoke Detector Sensor

Please contact Toshiba directly or a Toshiba vendor for more information.

Figure 8: EMD Sensor Pack

RemotRadar Software (Sold Separately)

Is a real-time monitoring solution software application that allows monitoring up to 5,000 RemotEye II/IIIs all at-

once (See Figure 9: RemotRadar Example). It also has the ability to send SMS and Email notifications when an event

occurs to one of the Toshiba UPS. Please contact Toshiba directly or a Toshiba vendor for more information.

Installation

RemotEye III User Manual – 62330-005

Figure 9: RemotRadar Example

15

System Compatibility

The RemotEye III works with 1600XP, 4200FA, and 4300 Series Toshiba UPS system family:

Installing RemotEye III

Follow these steps to install the RemotEye III card.

1. Turn the UPS off using the proper shutdown procedure as explained in the UPS manual.

2.

3.

Slide the RemotEye III printed circuit board into the extension option slot of the UPS.

Secure the printed circuit board using the UPS supplied screws.(See Figure 10: RemotEye III Location in

1600XP UPS, Figure 12: RemotEye III in 4300 UPS)

Figure 10: RemotEye III Location in 1600XP UPS

16 RemotEye III User Manual – 62330-005

RemotEye III Located on

Inside Left Door of

50kVA model

RemotEye III Located on Deadfront of

15-30kVA model

Figure 11 RemotEye III Location in 4200FA

Figure 12: RemotEye III in 4300 UPS

RemotEye III User Manual – 62330-005 17

Making the Network Connection

Each Ethernet network is different. Therefore, the following steps should be used as an outline for connecting the

RemotEye III to a network (See Figure 13: Network Connection Example):

1. Connect one end of a Category 5 cable to the NETWORK RJ45 receptacle of RemotEye III.

2.

3.

Connect the other end of the Category 5 cable to a designated network switch, hub, or computer. A network administrator will need allocate an available port/IP address.

Verify a network link has been established. Confirm the left-most green LED is illuminated for 100Mbit/s or right-most amber LED is illuminated for 10Mbit/s.

Note: The RemotEye III’s “DHCP/BOOTP” setting comes enable by default. If there is a DHCP/BOOTP server within the network, the DHCP/BOOTP server will allocate (lease) an IP address to the RemotEye III.

This setting has to be disabled if using static IP address by going to “RemotEye III Management” 

“RemotEye III Control” on its web interface.

Cat5

Cable

Figure 13: Network Connection Example

18 RemotEye III User Manual – 62330-005

Configuration

RemotEye III must be configured for proper operation on its network which can be done by three convenient methods.

Preliminary Issues

RemotEye III is a network device. Several items should be considered prior to communicating with RemotEye III over the network. The following sections cover important topics when placing a device on an Ethernet network.

MAC Address

The Media Access Control (MAC) address is an identification number which uniquely identifies each Ethernet device on a network. The MAC address (sometimes called the physical address) is made up of 6 hexadecimal bytes.

A label marked with the MAC address is included with each RemotEye III. This label is affixed at the bottom of

every RemotEye III printed circuit board (See Figure 14: RemotEye III MAC Address Label).

Figure 14: RemotEye III MAC Address Label

For each RemotEye III, the MAC address is created using the following format: 00 E0 D8 LL MM NN. The first half of this code, 00 E0 D8, identifies the manufacturer of the Ethernet board. Since every RemotEye III is produced by the same manufacturer, these 3 hexadecimal bytes remain constant. The LL MM NN characters identify the serial number of the device in hexadecimal form. The serial number is unique for each RemotEye III device.

Default IP Address

The RemotEye III is initially configured with a default Internet Protocol (IP) address. By default, the 4 bytes composing the default IP address are derived from the MAC address in the following way:

172.18.xxx.yyy where xxx is the decimal value of the MM MAC address byte and yyy is the decimal value of the NN

MAC address byte.

Example: A RemotEye III MAC address of 00 E0 D8 0C 01 3F would have a default IP address of 172.18.1.63.

This places RemotEye III on a 172.18.0.0 IP network.

Default Network Mask

RemotEye III User Manual – 62330-005 19

The RemotEye III is initially configured with a default Network Mask. This default value is always: 255.255.0.0.

This places RemotEye III on a Class B network.

Default Gateway

The RemotEye III is initially configured with a Gateway address of 0.0.0.0. This value indicates RemotEye III will not attempt to use a gateway.

20 RemotEye III User Manual – 62330-005

Configuring via Terminal

The RemotEye III can be configured via a Terminal Emulator Software.

Hardware Setup

Direct configuration is accomplished through the provided RJ45 to DB9 female connector PC cable. Follow these

steps to setup the hardware for direct RemotEye III configuration (See Figure 15: Serial Communication Physical

Connection Example):

1. Connect the DB9 female end of the PC cable to the terminal or workstation COM port. NOTE: if no COM port is available, use a USB-to-Serial (RS-232) converter.

2. Connect the RJ45 end of the PC cable to the COM port of RemotEye III.

RJ45 End

RJ45 to DB9

Female

Cable

DB9

Female End

Figure 15: Serial Communication Physical Connection Example

Software Setup

The direct communication can be performed from a workstation that is running a Terminal Emulator Software

(TES) such as HyperTerminal. The direct configuration is accomplished by RS232 communication protocol. If a

Terminal Emulator Software is not available, download “Tera Term” from the internet for free. The serial communication settings are discussed in the next section.

RemotEye III User Manual – 62330-005 21

Establishing Comminication

A direct configuration session can easily be established once the hardware and software are properly set up. Follow these steps to begin configuration:

Terminal Emulator Example

To configure RemotEye III from a Windows platform, use HyperTerminal (Except in Windows Vista, 7, or 8). If

HyperTerminal is not available, download “Tera Term” for free from the internet. (Contact Toshiba for additional information)

HyperTerminal is a standard terminal emulator packaged with all Windows operating systems except in Vista/7.

Launch the HyperTerminal program by navigating to Start

→ Programs → Accessories → Communication →

HyperTerminal, and follow the prompts.

Enter a name (e.g. RemotEye III) and select an icon for the application at the Connection Dialog box.

Select a direct connection to an appropriate COM port listed in the “Connect Using” pull-down menu.

Ensure that the Properties dialog box is setup accordingly.

• Baud Rate — 9600

• Data Bits — 8

• Parity — None

• Stop Bits — 1

• Flow Control —-None

Press [Enter] and the RemotEye III version and Password field will be displayed (See Figure 16).

RemotEye III retains the password of the UPS it is connected to. If the RemotEye is brand new right out of the box the default password is “ADMIN.”

Password (case sensitive): ADMIN

Once connected to the UPS, RemotEye will try to verify the password by using the default. There are two ways this password can be changed on the RemotEye:

1.) Once RemotEye has verified password on UPS; if users manually changed the admin password on the UPS while

RemotEye is still connected then RemotEye will retain the new password.

2.) If password on UPS was changed before RemotEye was connected: users should follow these steps.

a.) Plug RemotEye into the UPS

b.) Open RemotEye html page.

c.) Enter as administrator using the new password.

Once RemotEye enters admin page using the new password, RemotEye will retain this password.

Enter the password and press [Enter] to display the RemotEye III Main Menu.

+===================================================================+

| [ TIC RemotEye III Login Menu ] |

+===================================================================+

Enter Password: ******

Figure 16: Console Login Screen

The seven options provided in the RemotEye III Main Menu provide access to all system RemotEye III configuration parameters. These options and their submenus are discussed in more detail in the next section.

22 RemotEye III User Manual – 62330-005

RemotEye III Configuration Menu Navigation

The main menu of the RemotEye III provides access to configuration parameters. The table below provides an

overview of the entire menu structure (See Table 1: Menu Map for RemotEye III Console). When navigating through

these menus, all alpha-numeric characters are acceptable and are case-sensitive.

RemotEye III Main Menu

(1) TIC RemotEye III

Configuration

(1) System Group

(4) Email Group

(5) EMD Group

(2) Control Group

(3) Parameter Group

RemotEye III Agent Version

Ethernet Address

(1) IP Address

(2) Gateway Address

(3) Network Mask

(4) Date and Time

(5) Dump Modules CRC value

(0) Return to Previous Menu

(1) HTTP Login Username

(2) Community Read-On1y

(3) Community Read/Write

(4) BOOTP/DHCP Control

(5) Telnet Control

(6) Network Upgrade Control

(7) HTTP Security Control

(8) SNMP Version Control

(9) HTTP(s) Authentication

(0) Return to Previous Menu

(1) System Contact

(2) System Name

(3) System Location

(4) Poll Rate

(0) Return to Previous Menu

(1) Mail Server

(2) User Account

(3) User Password

(4) Domain Name

(5) DNS IP Address

(6) Daily Status Report

(7) Mail Receivers

(8) Test Email Configuration

(9) Authentication Method

(0) Return to Previous Menu

(1) Temperature Group

(2) Humidity Group

(3) Alarm-1 Group

RemotEye III User Manual – 62330-005 23

(1) TIC RemotEye III

Configuration (CONT)

(5)EMD Group (CONT)

(2) SNMP Communities

(3) SNMPV3 USM Table

(4) Trap Receiver Table

(5) Reset Configuration to Default

(4) Alarm-2 Group

(5) Device Status

(0) Return to Previous Menu

(6) Web Authentication

Group

(1) RADIUS Group

(0) Return to previous menu

(0) Return to Previous Menu

(1) Modify

(2) Reset

(0) Return to Previous Menu

(1) Modify

(2) Reset

(0) Return to Previous Menu

(1) Modify

(2) Reset

(0) Return to Previous Menu

Reset Configuration (y/n)?

(6) Save and Exit

(7) Save and Restart RemotEye III Restart Agent (y/n)?

Table 1: Menu Map for RemotEye III Console

24 RemotEye III User Manual – 62330-005

Main Menu Description

The Main Menu of the RemotEye III consists of the following options (See

Figure 17: Console Main Menu Description):

1.

2.

3.

4.

Toshiba RemotEye III Configuration

SNMP Communities

SNMPv3 USM Table

Trap Receiver Table

5.

6.

Reset Configuration to Default

Save and Exit.

7. Save and Restart Agent.

Press the number of the associated selection and press [Enter].

+====================================================================+

| [ TIC RemotEye III Main Menu ] |

+====================================================================+

1. TIC RemotEye III Configuration

2. SNMP Communities

3. SNMPV3 USM Table

4. Trap Receiver Table

5. Reset Configuration To Default

6. Save and Exit

7. Save and Restart Agent

Please Enter Your Choice =>

Figure 17: Console Main Menu Description

RemotEye III User Manual – 62330-005 25

TIC RemotEye III Configuration

Main Menu

→ (1) Toshiba RemotEye III Configuration (See

Figure 18: Console Configuration Menu Description).

The Toshiba RemotEye III Configuration option provides access to the following system settings:

1.

2.

3.

4.

5.

6.

System Group

Control Group

Parameter Group

Email Group

EMD Group

Web Authentication Group

0. Return to Previous Menu

+==================================================================+

| [ TIC RemotEye III Configuration Menu ] |

+==================================================================+

1. System Group

2. Control Group

3. Parameter Group

4. Email Group

5. EMD Group

6. Web Authenication Group

0. Return to previous menu

Please Enter Your Choice =>

Figure 18: Console Configuration Menu Description

26 RemotEye III User Manual – 62330-005

System Group

Main Menu

→ (1) Toshiba RemotEye III Configuration → (1) System Group (See

Figure 19: Console System Group Menu Description).

The System Group provides access to the system settings listed below. The settings may be viewed or changed from this screen. When using the Dynamic Host Configuration Protocol (DHCP), items 1 – 3 will be retrieved automatically.

1. IP Address — RemotEye III IP address.

2.

3.

4.

Gateway Address — The gateway IP address (if a router is necessary).

Network Mask — The network mask for the RemotEye III network.

Date and Time — The RemotEye III date and time format is MM/DD/YYYY, and HH:MM:SS respectively. RemotEye III supports the Network Time Protocol (NTP) and NTP. These two features

enable the UPS to synchronize its date and time with a NTP server. (See

5.

Figure 20: Date & Time Menu Description).

Dump modules CRC value

0. Return to Previous Menu.

+====================================================================+

| [ System Group Menu ] |

+====================================================================+

RemotEye III Agent Version : TIC RemotEye III v1.03

Ethernet address : 00 E0 D8 08 80 0D

1. Ip Address : 172.18.1.63

2. Gateway Address : 172.18.1.1

3. Network Mask : 255.255.240.0

4. Date and Time

5. Dump Modules CRC value

0. Return to previous menu

Please Enter Your Choice =>

Figure 19: Console System Group Menu Description

+=================================================================+

| [ Date and Time Menu ] |

+=================================================================+

1. System Date (dd/mm/yyyy) : 03/01/2012

2. System Time (hh:mm:ss) : 12:22:21

3. NTP Server : 0.0.0.0

4. NTP Time Zone : -06:00

5. Daylight Saving Time Control : Enabled

6. NTP Control : Enabled

0. Return to previous menu

Please Enter Your Choice =>

Figure 20: Date & Time Menu Description

RemotEye III User Manual – 62330-005 27

Control Group

NOTE: MODBUS TCP protocol can only be set up via HTTP (web browser). See page 38.

Main Menu

→ (1) Toshiba RemotEye III Configuration → (2) Control Group (See Figure 21: Console Control

Group Menu Description)

The Control Group menu provides access to the system settings listed below. The settings may be viewed and changed from this screen.

1.

2.

3.

4.

5.

6.

7.

8.

HTTP Login Username — The login username grants write access from a web browser (the default setting is TOSHIBA).

Community Read-Only — This common community name provides read-only access to devices within this community. (The default setting is “public”.)

Community Read/Write — This common community name provides read and write access to devices within this community. (The default setting is “admin”.) This value is equivalent to the terminal/telnet login password.

BOOTP/DHCP Control — This parameter is used to enable or disable the BOOTP/ DHCP requests from

RemotEye III. (The default setting is “Enabled”).

Telnet Control — This parameter is used to enable or disable remote RemotEye III configuration through telnet applications. (The default setting is “Enabled”).

Network Upgrade Control — This parameter is used to enable or disable the Trivial File Transfer

Protocol image upgrade. When disabled, RemotEye III will block any attempts to upgrade. (The default setting is “Disabled”.)

HTTP Security Control — This parameter is used to enable or disable the web password protection feature. When enabled, a password is required to access RemotEye III through the web, and write privileges are automatically assumed. When disabled, any machine can access RemotEye III over the web, but a password is required prior to assuming write privileges. (The default setting is “Disabled”.)

SNMP Version Control —This parameter is used to enable and disable the Simple Network Management

Protocol security level. When enabled, administrators has the options to set for SNMPv1 or SNMPv3.

9. HTTP(s) Authentication — This parameter allows the administrators to select what type of authentication is required to gain access to the RemotEye III web content. There are three options Local User, Radius, or both. If “Local User” is selected, the user will be authenticated when accessing the RemotEye III web content. If “Radius” is selected, the user will have to be authenticated first by a RADIUS server in order to access the RemotEye III web content. If “both” is selected, then the user can be either authenticated through Radius or through the RemotEye III web authentication feature. (The default setting is Local

User)

0. Return to Previous Menu

+====================================================================+

| [ Control Group Menu ] |

+====================================================================+

1. HTTP Login Username : TOSHIBA

2. Community Read-Only : public

3. Community Read/Write : *

4. BOOTP/DHCP Control : Enabled

5. Telnet Control : Enabled

6. Network Upgrade Control : Disabled

7. HTTP Security Control : Disabled

8. SNMP Version Control : Disabled

9. HTTP<s> Authenication : Local User

0. Return to previous menu

Please Enter Your Choice =>

Figure 21: Console Control Group Menu Description

28 RemotEye III User Manual – 62330-005

Parameter Group

Main Menu

→ (1) Toshiba RemotEye III Configuration → (3) Parameter Group (See

Figure 22: Console Parameter Group Menu Description)

The Parameter Group provides access to the system settings listed below. The settings may be viewed or changed from this screen.

1.

2.

3.

System Contact — The RemotEye III system administrator. This string can be changed by administrator as desired.

System Name — The alias of the RemotEye III. This string serves as the RemotEye III Client Identifier

(CID) in DHCP systems.

System Location — The RemotEye III physical location. This string can be changed by administrator as desired.

4. Poll Rate — The polling rate in seconds. This determines how frequently RemotEye III updates its data from the Toshiba UPS. (The default setting is 5 seconds)

0. Return to previous menu.

Note: System will label each event email with the system Name and Location, in the format: systemName@SystemLocation

Example: RemotEye III@Toshiba

+====================================================================+

| [ Parameter Group Menu ] |

+====================================================================+

1. System Contact : TIC Local Technical Support

2. System Name : RemotEye III

3. System Location : Toshiba

4. Poll Rate : 5

0. Return to previous menu

Please Enter Your Choice =>

Figure 22: Console Parameter Group Menu Description

RemotEye III User Manual – 62330-005 29

Email Group

Main Menu

→ (1) Toshiba RemotEye III Configuration → (4) Email Group (See

Figure 23: Console Email Group Menu Description)

The Email Group menu provides access to the system settings listed below. The settings may be viewed and changed from this screen.

1. Mail Server — The Simple Mail Transfer Protocol (SMTP) mail server IP address. If a hostname is used, such as smtp.tic.toshiba.com, the Domain Name Server (DNS) IP address is required on setting 5.

2.

3.

User Account — The user account login name for the SMTP mail server.

User Password — The user account password for the SMTP mail server.

Note: Not all servers require login name and password, please check with SMTP administrator.

4.

5.

6.

7.

Domain Name — The domain Name (Network Name) of the mail server (e.g. Tic.Toshiba.com).

DNS IP Address — Domain Name System Server IP address is required if a hostname is used for Mail

Server (If hostname is used in the setting 1). Otherwise, this field can be 0.0.0.0.

Daily Status Report — This parameter is used to set the time to send RemotEye III daily status report that are listed in the “Mail Receivers” setting (7).

Mail Receivers — This Parameter is used to enter up to four recipients email address and select the “Mail

Type” for each recipient. Here is the list on the three different Mail Types: a. None: Disable option to send email to recipients.

8. b. Events – Current events will be sent to recipients. c. Events with Status – Current events, History log and Event log will be sent to email recipients when events occurred.

The recipients include users who use Short Message System (SMS) in Email address format, such as [email protected]

. Check with service carrier for the correct format to receive text messages.

Test Email Configuration — This parameter allows the administrator to send out a test email to verify system operation is configured correctly. If instant email is not received after the test, please check the configuration.

9. Authentication Method

0 Return to Previous Menu

+===================================================================+

| [ Email Group Menu ] |

+===================================================================+

1. Mail Server :

2. User Account :

3. User Password : *

4. Domain Name : 0

5. DNS IP Address : 0.0.0.0

6. Daily Status Report : 00:00

7. Mail Receivers

8. Test Email Configuration

9. Authentication Method:

0. Return to previous menu

Please Enter Your Choice =>

Figure 23: Console Email Group Menu Description

30 RemotEye III User Manual – 62330-005

EMD Group

Main Menu

→ (1) Toshiba RemotEye III Configuration → (5) EMD Group (See Figure 24: Console EMD Group

Menu Description)

The EMD Group menu provides access to the system settings listed below. The settings may be viewed and changed from this screen.

1.

2.

3.

4.

Temperature Group — The Temperature Group provides the options to setup the low and high warning and critical points. Users also have the options to setup the hysteresis and calibration offset from this group.

Humidity Group — The Humidity Group provides the options to setup the low and high warning and critical points. Users also have the options to setup the hysteresis and calibration offset from this group.

Alarm-1 Group — The Alarm-1 Group provides the option to setup this dry contact as normal close, normal open, high active, low active and disabled.

Alarm-2 Group — The Alarm-2 Group provides the option to setup this dry contact as normal close, normal open, high active, low active and disabled.

5. Device Status — The Device Status allows the administrator to allow RemotEye III to auto-detect EMD or to disable. “Auto” will enable the RemotEye III to auto detect the EMD that is connected to its COM port.

Note: These features apply to EMD module only. EMD sold separately.

+================================================================+

| [ EMD Group Menu ] |

+================================================================+

1. Temprature Group

2. Humidity Group

3. Alarm-1 Group

4. Alarm-2 Group

5. Device Status : Auto

0. Return to previous menu

Please Enter Your Choice =>

Figure 24: Console EMD Group Menu Description

RemotEye III User Manual – 62330-005 31

SNMP Communities

Main Menu

→ (2) SNMP Communities (See Figure 25: SNMP Communities Description).

The SNMP Communities lists the status and configuration of access rights that are currently granted and the applicable level of access. The entries in this table are largely responsible for restricting SNMP communication with

RemotEye III.

The configuration of the SNMP communities shall be as follows:

IP Address: IP address of the NMS

Community String: NMS Get/Set Community String.

(Please refer to SNMP Get/Set Criteria on page 100 for a more detailed explanation on Get/Set.)

Access: Select Access Type:

1. Read Only

2. Read/Write

3. No Access

+====================================================================+

| IP Address Community String Access |

+====================================================================+

[1] 0.0.0.0 * No Access

[2] 0.0.0.0 * No Access

[3] 0.0.0.0 * No Access

[4] 0.0.0.0 * No Access

[5] 0.0.0.0 * No Access

[6] 0.0.0.0 * No Access

[7] 0.0.0.0 * No Access

[8] 0.0.0.0 * No Access

COMMANDS -

1. Modify - Modify an entry of table

2. Reset - Reset an entry to default from table

0. Return to previous menu

Please Enter Your Choice =>

Figure 25: SNMP Communities Description

32 RemotEye III User Manual – 62330-005

SNMPv3 USM Table

Main Menu

→ (3) SNMPv3 USM Table (See Figure 26: SNMPv3 USM Menu Description).

The SNMPv3 USM Table lists the status and configuration of access rights that are currently granted and the applicable level of access. The entries in this table are largely responsible restricting SNMPv3 security with

RemotEye III.

The configuration of the SNMPv3 USM table shall be as follows:

User Name: The User ID for the authorized individual.

Authentication Password: The password string for the authorized individual.

Privacy Password: The privacy password string for the authorized individual.

Security: The security level provides the following 3 options:

1. noAuthNoPriv – with no authentication and no privacy passwords

2.

3. authNoPriv – with authentication password but no privacy password authPriv – with authentication password and with privacy password

Authentication format: The authentication format provides the following options:

1.

2.

HMAC-MD5

HMAC-SHA

Status Type: The status shows the authentication status “ready” or “not being used".

+====================================================================+

| User Name Authentication. Password Privacy Password |

| Security Authentication Format Status Type |

+====================================================================+

[1]

noAuthNoPriv HMAC-MD5 Not Use

[2]

noAuthNoPriv HMAC-MD5 Not Use

[3]

noAuthNoPriv HMAC-MD5 Not Use

[4]

noAuthNoPriv HMAC-MD5 Not Use

COMMANDS -

1. Modify - Modify an entry of table

2. Reset - Reset an entry to default from table

0. Return to previous menu

Please Enter Your Choice =>

Figure 26: SNMPv3 USM Menu Description

RemotEye III User Manual – 62330-005 33

Trap Receiver Table

Main Menu

→ (4) Trap Receiver Parameters (see Figure 27: Console Trap Receiver Table Description).

The Trap Receiver Table lists IP addresses of the administrative machines that have been assigned to receive traps.

The configuration of the trap receivers shall be as follows:

IP Address: IP address of the NMS.

Community String: NMS community string.

Trap Type:

1.

2.

3.

None

Toshiba Trap

JEMA Trap

4. IETF Trap

Description: Description of the NMS. This is administrator defined (max 10 characters)

Severity Level:

Informational – The receiver will receive the following trap types “Fault”, “Warning” and “Informational”.

Warning – The receiver will receive the following trap types “Fault” and “Warning”.

Severe – The receiver will receive the following trap type only “Fault”.

+================================================================================+

| IP Address Community String Trap-Type Severity Desc |

+================================================================================+

[1] 192.168.1.50 * Toshiba Trap Informational

[2] 0.0.0.0 * None Informational

[3] 0.0.0.0 * None Informational

[4] 0.0.0.0 * None Informational

[5] 0.0.0.0 * None Informational

[6] 0.0.0.0 * None Informational

[7] 0.0.0.0 * None Informational

[8] 0.0.0.0 * None Informational

1. Modify - Modify an entry of table

2. Reset - Reset an entry to default from table

0. Return to previous menu

Please Enter Your Choice =>

Figure 27: Console Trap Receiver Table Description

34 RemotEye III User Manual – 62330-005

Reset Configuration to Default

Main Menu

→ (5) Reset Configuration to Default.

Selecting this option restores all RemotEye III card settings to its original default values.

Note: This will reset every configuration including the IP settings.

From the Main Menu, press 5 to access the Reset Configuration to the Original Setting screen.

Save and Exit

Main Menu

→ (6) Save and Exit.

When executed, the system saves the RemotEye III configuration and exits the program. The new configuration takes effect immediately.

Save and Restart RemotEye III

Main Menu

→ (7) Save and Restart RemotEye III.

When executed, the system saves the RemotEye III configuration and restarts RemotEye III program.

RemotEye III User Manual – 62330-005 35

Configuring the RemotEye III via Telnet

The RemotEye III can be configured by establishing a telnet session with the device.

Hardware Setup

Telnet configuration is accomplished through a network link. Follow these steps to setup the RemotEye III for a telnet session:

Verify network cable connection to NETWORK port of RemotEye III.

Verify active link to LAN or Network.

For further information on the network connection, refer to “Making the Network Connection” on page 18.

Software Setup

The Telnet configuration is accomplished through a TCP/IP network connection. A telnet connection can be established with RemotEye III by using any Telnet application. Follow these steps to setup the software for Telnet

RemotEye III configuration:

Verify workstation is loaded with Telnet application. If using Windows operating system, “Command Prompt” application software that is packed with Windows can be used. If a Telnet application is not available or Command

Prompt, download “Tera Term” software from the internet for free.

Note: If using Windows 7 or Vista, make sure that Telnet feature is enabled. By default, Windows 7 and Vista

Operating System have this feature disabled for security reasons. To enable this feature, follow these steps:

1. Click on “Start”

2. Go to and click on “Control Panel”

3. Go to and click on “Programs and Features”

4. On the left side column, click on “Turn Windows features on or off” (See Figure 28: Enable Telnet Feature on Windows 7/Vista). Now look for “Telnet Client” and click on the check box to enable. Then click on the

“Ok” button and wait till feature is enabled.

36

Figure 28: Enable Telnet Feature on Windows 7/Vista

RemotEye III User Manual – 62330-005

Verify a valid network path exists between the RemotEye III and the workstation. If performing the Telnet

configuration from a workstation that is located on the same network, then proceed to the next section “

Connecting to the RemotEye III via Telnet” on page 37.

Routing to the RemotEye III

If the workstation is not on the same network as the RemotEye III, the system may require the addition of a network route. This is typically only necessary when RemotEye III is using its default address.

Consult operating system documentation pertaining to the addition of network routes for instruction.

Example Route Addition

Windows operating systems provide the command Route Add for adding network routes.

Assume the default IP Address of the RemotEye III is 172.18.1.63, and assume the IP Address of the workstation is

210.67.192.147. To add the appropriate network route between these two devices, follow these steps:

Turn on the workstation, and setup the TCP/IP protocol (if necessary).

Enter the following command to add a routing condition (e.g. Command Prompt in Windows OS):

Route add 172.18.1.63 210.67.192.147

See the Windows manual for further information on how to add a routing condition to a workstation.

Connecting to the RemotEye III via Telnet

A telnet configuration session can be established once the hardware and software are prepared. Open the Telnet application software and follow these steps to begin configuration:

1. Type telnet followed by the IP address of RemotEye III to a telnet application (e.g. telnet 192.168.1.50).

2.

3.

Press [Enter].

Key in the password when prompted.

Default Password (case sensitive): ADMIN

For more information on using telnet, please refer to telnet application Windows help.

The RemotEye III will only accept 2 telnet clients simultaneously. The telnet connections will time-out after

60 seconds of inactivity.

RemotEye III Telnet Menu Navigation

The configuration menus for telnet configuration are identical to those presented by a direct configuration session.

Refer to page 23 for detailed guidance through configuration menus of RemotEye III.

RemotEye III User Manual – 62330-005 37

Configuring the RemotEye III via HTTP

The RemotEye III can be configured by opening a web session (e.g. Internet Explorer, Firefox, and Google Chrome).

Hardware Setup

Web configuration is accomplished through a network link. Follow these steps to prepare the hardware for HTTP

RemotEye III configuration:

1.

2.

3.

Verify network cable connection to NETWORK port of RemotEye III.

Verify active link to LAN or Network.

For further information on the network connection, refer to “Making the Network Connection” on page

18.

Software Setup

The web configuration is accomplished through a TCP/IP network connection. A web connection can be established with RemotEye III by using any Internet Browser application (for example, Firefox). Follow these steps to setup the software for web-based RemotEye III configuration:

1.

2.

Verify workstation is loaded with web browser application (e.g. Internet Explorer).

Verify a valid network path exists between RemotEye III and the workstation. If performing the web configuration from a workstation that is located on the same network, then proceed to the next section.

Otherwise, refer back to the section entitled “Routing to the RemotEye III” on page 37.

System Setup

To access the RemotEye III via the web, enter the IP address of the RemotEye III in the URL field of the browser and

press Enter (See Figure 29: RemotEye III with Internet Explorer Example). If unable to access the RemotEye III due

to a firewall, contact the network administrator for information on bypassing the firewall of the LAN.

38

Figure 29: RemotEye III with Internet Explorer Example

RemotEye III User Manual – 62330-005

The HTTP Security Control setting may also affect the user’s ability to access the RemotEye III. The HTTP Security

Control setting may be set or viewed from: Main Menu

→ (1) TIC RemotEye III Configuration →(2) Control Group

→ (7) HTTP Security Control (See Figure 30: HTTP Security Control Window).

If the HTTP Security Control setting is Disabled, the user is granted read-only access. If the HTTP Security Control

is Enabled, any attempt to access RemotEye III pages will be met with a request to enter a password (See Figure 30:

HTTP Security Control Window).

Login:

TOSHIBA

Password:

ADMIN

Figure 30: HTTP Security Control Window

Once the password has been entered in the user will be able to not only view the information, but make changes accordingly. The password is the same as the Community Read/Write string (See via Telnet or Serial RS-232 communication: Main Menu

→ (1) Toshiba RemotEye III Configuration → (2) Control Group → (3) Community

Read/Write).

To prevent unauthorized users from configuring the RemotEye III via HTTP, the IP address of the workstation must be entered in the RemotEye III SNMP Communities/HTTP Access Control with no access permissions (via RS232 or

Telnet) or the SNMP/ HTTP Access Control (via Web Browser) of the RemotEye III. Otherwise, the RemotEye III will provide only read access to its parameters.

RemotEye III User Manual – 62330-005 39

Connecting to the RemotEye III via HTTP

A web session can be established once the hardware and software have been prepared. Follow these steps to begin configuration:

1.

2.

Launch the web browser (e.g. Internet Explorer).

Enter the URL for RemotEye III in the browser’s address field. For example, http://172.18.1.63. The

home page of the RemotEye III will be displayed once a connection is established (See Figure 31:

RemotEye III HTTP Page).

Perform the following procedure to setup the RemotEye III Static IP address, protocols and Date/Time using its provided web configuration pages.

1.

2.

Select “RemotEye III Management”

→ “RemotEye III Configuration” to configure RemotEye III.

Click the Become Administrator button at the bottom of the screen. The password is case sensitive.

Login: TOSHIBA

3.

4.

5.

6.

7.

Password: ADMIN

Non-DHCP users continue on to step 3. DHCP users may skip steps 3 to 6.

Enter the RemotEye III IP address.

Enter the RemotEye III Gateway address in the network.

Enter the RemotEye III Network Mask of the network.

Click Set Value to save the settings.

Select “RemotEye III Management”

→ “Date and Time” to set date and time.

8. Enter the appropriate date and time in the specified format.

9. Click Set Value to save the settings.

10. Select “RemotEye III Management”

→ “RemotEye III Control” to enable or disable the network protocols.

Note: Disable “RemotEye III DHCP Control” setting if using static IP.

40

Figure 31: RemotEye III HTTP Page

RemotEye III User Manual – 62330-005

RemotEye III Web Menu Navigation

The RemotEye III home page is comprised of six primary menus:

• UPS Monitoring

• UPS Management

• Email Notification

• EMD

• RemotEye III Management

• History Data and Logs.

The six primary menus provide access to UPS and RemotEye III monitoring and control functions, and each is discussed in detail in the following sections.

UPS Monitoring

This menu allows the user to view the collected data from the UPS measurements. The UPS measured parameters are

listed below and are allowed only to be read (See Figure 32: RemotEye

III Web UPS Monitoring Directory).

1. Comprehensive View

2. UPS Data General

3. UPS Data Display

4. UPS Data Other (Not Available for 4300)

5. Input Parameters

6. Output Parameters

7. Bypass Parameters

8. DC Bus Parameters

9. Battery Parameters

10. Alarm Table

11. Connected Client Table

Figure 32: RemotEye III Web UPS Monitoring Directory

RemotEye III User Manual – 62330-005 41

Comprehensive View

This web page lists the UPS parameters. This page will refresh automatically at a user-defined rate. To change or view the refresh rate setting, select “RemotEye III Management”

→ “HTTP Page Refresh Rates” in the RemotEye III web interface.

Parameter #

1

2

3

4

5

6

7

Object

UPS Mode

Input Voltage (V)

Input Frequency (Hz)

Output Voltage (V)

Comprehensive View Parameters

Description

This field shows the present UPS system mode.

These readings include:

Start-Up, On-Line, Bypass,

Backup, Battery Test, and

Shutdown.

Output Load Percentage (%)

Output Frequency (Hz)

UPS System Temperature (°C)

This field shows the present UPS input voltage in VAC.

This field shows the present UPS input frequency in Hz.

This field shows the present UPS output voltage in VAC.

This field shows the present UPS load in % of kVA.

This field shows the present UPS output frequency in Hz.

This field shows the present UPS temperature in °C.

1600XP

4200FA

4300

This field shows the present UPS battery temperature in °C.

8

UPS Battery Temperature (°C)

  

9

10

11

12

Battery Capacity (%)

Battery Runtime (Mins)

Date On RemotEye III (mm/dd/yyyy)

Time On RemotEye III (hh:mm:ss)

This field shows the present UPS battery capacity in percentage.

This field shows the present UPS battery runtime in minutes.

This field shows the

RemotEye III date setting.

This value is displayed in the mm/dd/yyyy format.

This field shows the

RemotEye III time setting.

This value is displayed in the hh:mm:ss 24-hour format (i.e. 8:30 p.m. is

20:30:00).

UPS Data General

42 RemotEye III User Manual – 62330-005

This web page allows the user to retrieve the UPS identification and revision information.

UPS Data General Parameters

Parameter #

1

2

3

4

5

6

7

8

9

10

11

12

13

14

Object

UPS Manufacture

UPS Typeform

UPS Description

UPS Serial Number

UPS Main Firmware Version

UPS Main Boot Sector Version

UPS Main Boot Loader Version

UPS Job Number

UPS Test Date

UPS Hardware Build Date

UPS EEPROM Version

UPS System Name

UPS Attached Devices

UPS Installation Date

Description

This field shows the name of the

UPS manufacturer.

This field shows the typeform of the UPS to which RemotEye III is presently attached.

This field shows the model description of the UPS to which

RemotEye III is presently attached.

This field shows the UPS manufactured serial number for the UPS which RemotEye III is presently attached.

This field shows the present firmware version for the UPS.

This is for informational

This field shows the present boot sector version for the UPS.

This is for informational purpose.

This field shows the present boot loader version for the UPS.

This is for informational

This field shows the present job number for the UPS. This is for informational purpose.

This field shows the date the

UPS was last tested. This is for informational purpose.

This field shows the date the

UPS was built. This is for informational purpose.

This field shows the present

EEPROM version for the UPS.

This is for informational

This field shows the administrator-configured name of the UPS. For configuration, please refer to UPS

This field shows the administrator configured description of the load devices that attached to the UPS (e.g. computers, communication devices, etc). For configuration, please refer to UPS

Configuration menu.

This field shows the date the

UPS was installed. For configuration, refer to the UPS

Configuration menu.

1600XP

4200FS

4300

RemotEye III User Manual – 62330-005 43

UPS Data Display

This page shows the UPS Display Information. This page will refresh automatically at a user-defined rate. To change or view the refresh rate setting, select “RemotEye III Management”

→ “HTTP Page Refresh Rates” in the RemotEye

III web interface.

Parameter #

1

2

3

4

5

6

7

8

Object

Display Firmware Version

Display Boot Sector Version

Display Boot Loader Version

Display Sleep Timer (Mins)

Display Buzzer Mode

Display Buzzer Status

Display Firmware Built Date

Display Firmware Built Time

UPS Data Display Parameters

Description

This field shows the present firmware version for the display. This is for informational purpose.

This field shows the present boot sector version for the display.

This is for informational

This field shows the present boot loader version for the display.

This is for informational

This field shows the amount of time the display will remain active before it will enter to sleep mode.

This field shows the current buzzer mode. Users can specify at what conditions the buzzer can

This field shows the current status of the buzzer. This will determine if the alarm is silenced or sound if an alarm should

This field shows the

Firmware built date for the display. This is for informational purpose.

This field shows the

Firmware built time for the display. This is for informational purpose.

1600XP

4200FA

4300

44 RemotEye III User Manual – 62330-005

UPS Data – Other

This page shows the UPS states. This page will refresh automatically at a user-defined rate. To change or view the current refresh setting, select “RemotEye III Management”

→ “HTTP Page Refresh Rates” in the RemotEye III web interface.

UPS Data-Other Parameters

Parameter #

1

2

3

4

Object

EPO Contact State

UPS Run Stop Switch Status

UPS Service Port Status

Internal Communication Status

Description

This field shows the current contact state of the

Emergency Power Off

(EPO).

This field shows the current state of the run (On-

Line)/stop (Bbypass) switch on the UPS.

This field shows the current status of the UPS

Service Port on the UPS.

This will inform users if an error has occurred.

This field shows the internal communication status for the UPS. This will inform users if an error has occurred.

1600XP

4200FA

4300

RemotEye III User Manual – 62330-005 45

Input Parameters

This page shows the UPS line voltage input readings. This page will refresh automatically at a user-defined rate. To change or view the current refresh rate setting, select “RemotEye III Management”

→ “HTTP Page Refresh Rates” in the RemotEye III web interface.

Input Parameters

Parameter #

Object 1600XP 4300 4300

1

2

3

4

5

Input Power Supply Configuration

Input Number of Lines input Voltage (V)

Input Voltage Percent (%)

Input Rated Voltage (V)

Description

This field shows the present power supply information at the input for the UPS.

This field shows the number of input lines for the UPS.

This field shows the UPS input voltage in VAC.

This field shows the UPS input voltage in percent.

This field shows the input rated voltage of the UPS. This can be changed by the administrator.

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

Input Current (Amps)

Input Current Percent (%)

This field shows the present UPS input current in Amps.

This field shows the UPS input current in percent.

This field shows the input rated current of the UPS in Amps.

Input Rated Current (Amps)

Input Frequency (Hz)

Input Rated Frequency (Hz)

Input Active Power (Watts)

Input Rated Power (Watts)

Input Rated Power (VA)

VIUV Detection Level (%)

VIOV Detection Level (%)

Input Phase Check

This field shows the UPS input frequency in Hz.

This field shows the input rated frequency of the UPS.

This field shows the present UPS input active power in Watts.

Input Rated Active Power (Watts)

Input Apparent Power (VA) input Power Factor

Input Line to Neutral Voltage (V)

This field shows the present UPS input rated active power in

Watts.

This field shows the present UPS input apparent power in Volt-

Amps.

This field shows the present UPS input power factor.

This field shows the UPS input

Line to Neutral in VAC.

This field shows the rated input

Line to Line voltage in VAC.

Input Rated Line to Line Voltage (V)

Input Rated Line to Neutral Voltage (V)

This field shows the rated input line to neutral voltage in VAC.

This field shows the input rated power in Watts.

This field shows the input rated power in VA.

This field shows the Voltage

Input Under-Voltage detection level in percent.

This field shows the Voltage

Input Over-Voltage detection level in percent.

This field shows the present status of input phase check.

When enabled it detects phase rotation error.

46 RemotEye III User Manual – 62330-005

Output Parameters

This page shows the UPS output voltage source and readings. This page will refresh automatically at a user-defined rate. To change or view the current refresh setting, select “RemotEye III Management”

→ “HTTP Page Refresh

Rates” in the RemotEye III web interface.

Parameter #

1

2

3

4

Object

Output Power Supply Configuration

Output Number of Lines

Output Voltage (V)

Output Rated Voltage (V)

Output Parameters

Description

This field shows the present power supply information at the output for the UPS.

This field shows the present phase of the output of the UPS.

This field shows the UPS output voltage in VAC.

This field shows the output rated voltage of the UPS.

This can be changed by the administrator.

1600XP

4300FA

4300

5

6

7

8

9

Output Under Voltage Level (%)

Output Over Voltage Level (%)

Output Current (Amps)

Output Rated Current (Amps)

Output Load Percentage (%)

This field shows the minimum allowable voltage before it falls into under voltage range.

This field shows the maximum limit of the output voltage before it the UPS enters the over voltage state.

This field shows the present UPS output current in Amps.

This field shows the present UPS output rated current in Amps.

This field shows the UPS load as a percentage of the maximum load setting.

10

11

12

13

14

15

16

17

Output Frequency (Hz)

Output Rated Frequency (Hz)

Output Frequency Synch Range (Hz)

Output Active Power (Watts)

Output Rated Active Power (Watts)

Output Apparent Power (VA)

Output Rated Apparent Power (VA)

Output Rated Power Factor

This field shows the present UPS output requnecy in Hz.

This field shows the present UPS output rated frequency in Hertz.

This field shows the allowable range for synchronizing output frequency.

This field shows the present UPS output active power in Watts.

This field shows the present UPS output rated active power in Watts.

This field shows the present UPS apparent power in VA.

TThis field shows the present UPS output rated apparent power in VA.

This field shows the present UPS output power factor.

RemotEye III User Manual – 62330-005 47

16

25

28

29

30

21

22

23

24

17

18

19

20

31

32

Output Rated Apparent Power (VA)

Output Rated Power Factor

Output Line to Neutral Voltage (V)

Output Voltage Percent (%)

Output Total Current Percent (%)

Output Current Percent (%)

Output Total Active Power (KW)

Output Total Active Power Percent (%)

Output Power Factor

Output Rated Line to Line Voltage (V)

Output Rated Line to Neutral Voltage (V)

Output Rated Power (Watts)

Output Rated Power (VA)

Output Under Voltage Detection Level (V)

Output Over Voltage Detection Level (V)

TThis field shows the present UPS output rated apparent power in VA.

This field shows the present UPS rated output power factor.

This field shows the UPS output line to neutral voltage in VAC.

This field shows the UPS output voltage in percent.

This field shows the present UPS output total current in percent.

This field shows the present UPS output current in percent.

This field shows the present UPS output active power in Kilowatts.

This field shows the present UPS output active power in percent.

This field shows the present UPS output power factor.

This field shows the UPS rated output line to line voltage in VAC.

This field shows the UPS rated output line to neutral voltage in VAC.

This field shows the present UPS output rated power in Watts.

This field shows the present UPS output rated power in VA.

This field shows the minimum allowable voltage before it falls into output under voltage range.

This field shows the maximum limit of the output voltage before the

UPS detect enters the

Output over voltage state.

48

 

RemotEye III User Manual – 62330-005

Bypass Parameters

This page shows the UPS bypass values. This page will refresh automatically at a user-defined rate. To change or view the current refresh setting, select “RemotEye III Management”

→ “HTTP Page Refresh Rates” in the RemotEye

III web interface.

Bypass Parameters

Parameter #

Object 1600XP 4200FA 4300

1

2

3

4

5

6

7

8

9

10

11

12

Bypass Power Supply Configuration

Bypass Number of Lines

Bypass Voltage (V)

Bypass Current (Amps)

Bypass Frequency (Hz)

Bypass Apparent Power (VA)

Bypass Under Voltage Detection (%)

Bypass Under Voltage Recovery (%)

Bypass Over Voltage Detection (V)

Bypass Over Voltage Recovery (V)

Bypass Line to Neutral Voltage (V)

Bypass Voltage Percent (%)

Description

This field shows the present power supply information during bypass for the UPS.

This field shows the number of bypass lines for the UPS.

This field shows the UPS voltage during bypass in

VAC.

This field shows the present UPS bypass current in Amps.

This field shows the present UPS bypass frequency in Hertz.

This field shows the present UPS bypass apparent power in VA.

This field shows the minimum allowable voltage before it falls into bypass under voltage range.

This field shows the allowable voltage that it can recover from under voltage.

This field shows the maximum allowable voltage before it falls into over voltage range.

This field shows the allowable voltage that it can recover from over voltage.

This field shows the present UPS bypass line to neutral voltage.

This field shows the UPS bypass voltage in percent.

13

14

Bypass Under Voltage Detection Level (%)

Bypass Over Voltage Detection Level (%)

This field shows the UPS bypass under voltage detection in percent.

This field shows the UPS bypass over voltage detection level in percent.

RemotEye III User Manual – 62330-005 49

DC Bus Parameters

This page shows the UPS DC Bus values. This page will refresh automatically at a user-defined rate. To change or view the current refresh setting, select “RemotEye III Management”

→ “HTTP Page Refresh Rates” in the RemotEye

III web interface.

DC Bus Parameters

Parameter #

1

2

3

4

Object

DC Bus Total Volatage (V)

DC Bus Positive Voltage (V)

DC Bus Negative Voltage (V)

DC Bus Rated Voltage (V)

Description

This field shows the DC Bus voltage in VDC.

This field shows the positive DC Bus voltage in

VDC.

This field shows the negative DC Bus voltage in

VDC.

This field shows the rated

DC Bus voltage in VDC.

1600XP

4200FA

4300

50 RemotEye III User Manual – 62330-005

Battery Parameters

This page provides the battery status and battery run-time information. This page will refresh automatically at a userdefined rate. To change or view the refresh rate setting, select “RemotEye III Management”

→ “HTTP Page Refresh

Rates” in the RemotEye III web interface.

Parameter #

1

2

3

4

5

6

7

8

9

10

11

12

Object

UPS Battery Status

Elapsed Time on Battery Power (Secs)

Battery Voltage (Vdc)

Calculated Battery Shutdown Voltage (Vdc)

Battery Discharge Current (Adc)

Battery Parameters

Description

This field shows the status of the UPS batteries. These readings include:

Unknown, Normal, Low,

Depleted, Discharging, and

Failure.

This field shows the elapsed time (in seconds) since the UPS switched to battery power.

This field shows the battery voltage in VDC.

This field shows the battery’s shutdown voltage in VDC.

This field shows the battery’s discharge current in Amps.

Battery Charge Status

Number of Discharge

Battery Life Reaming (Month)

Battery Rated Ampere Hour (Ahr)

This field shows the present Battery Charge status.

This field shows the present number of battery discharges.

This field shows the remaining battery life. The maximum battery lifetime is 5 years. This shows the remaining battery lifetime in months.

This field shows the present battery capacity in

Ampere Hour.

Battery in Series

Battery in Parallel

Battery Installation Date

This field shows the number of batteries connected in series.

This field shows the number of batteries connected in parallel.

This field shows the last installation date of the UPS system's batteries. This value is displayed in the dd/mm/yyyy format.

When the UPS batteries are replaced, this value should be adjusted accordingly by the service

1600XP

4200FA

4300

RemotEye III User Manual – 62330-005 51

21

22

23

24

26

27

28

13

14

15

16

17

18

19

20

Battery Voltage Shutdown Level (%)

Battery Low Level (%)

Battery Capacity (%)

Battery Runtime (Mins)

Battery Charge Over Voltage Delay (Secs)

Calculate Low Battery level (Vdc)

External Battery Install Status

External Battery in Series

External Battery in parallel

External Battery Rated Ampere Hour (Ahr).

External Battery C Rate

External Battery Install Date

Equalize Charge Time (Hours)

Float Charge Voltage (Vdc)

Battery Low Detection Level (Vdc)

This field shows the present battery voltage shutdown level in percent.

This field shows the battery low level in

The UPS battery capacity in percent.

The UPS battery runtime in minutes.

This field shows the battery charge over voltage delay in seconds.

This field shows the calculated low battery level in VDC.

This field shows installation status of the external battery. It can be installed or uninstalled.

This field shows the number of external batteries connected in series.

This field shows the number of external batteries connected in parallel.

This field shows the present external battery capacity in Ampere Hour.

This field shows the present external battery C

Rate.

This field shows the installation date of the external battery.

This field shows the battery equaliztion charge time in hours.

This field shows the float charge voltage in Vdc.

This field shows the minimum battery voltage in Vdc.

52 RemotEye III User Manual – 62330-005

Alarm Table

This page provides past and active UPS alarm activity and descriptions. This page will refresh automatically at a

user-defined rate (See Figure 33: RemotEye III Alarm Table Example). To change or view the refresh rate setting,

select “RemotEye III Management”

→ “HTTP Page Refresh Rates” in the RemotEye III web interface.

Figure 33: RemotEye III Alarm Table Example

Number of Present Alarms

This field shows the number of active UPS alarms.

Lastest Alarm

This field shows the last recorded UPS alarm in the format Date, Time, and Information about the alarm.

Alarm ID

This field shows the sequential number associated with the alarm; it indicates the activation sequence of the alarms.

This number will be reset after a RemotEye III reboot.

Alarm Time

This field shows the RemotEye III alarm time stamp. This value is displayed in the hh:mm mm/dd/yyyy format.

Note: The time depends on the RemotEye III clock setting.

Alarm Description

Info: UPS has encountered a change of state condition such as switching from on-line to bypass state.

Warning: UPS has encountered a noncritical abnormal condition that requires attention.

Fault: UPS has encountered a critical abnormal condition and requires attention. Please refer to the UPS manual for possible causes and solutions. If more information is needed or additional assistance is required, contact Toshiba authorized service center for Service.

1600XP Alarm/Trap Table

RemotEye III User Manual – 62330-005 53

2

3

ID Alarm Occur Message

1 upsAlarmFault upsAlarmOpenFuse upsAlarmCurrentLimitFault

4 upsAlarmDCBusOverCurrent

5

6

7 upsAlarmDCOverVoltage upsAlarmDCBusImbalance upsAlarmOutputUnderVoltage

8

9 upsAlarmOutputOverVoltage upsAlarmHeatSinkOverheat

10 upsAlarmBypassOverload

11 upsAlarmChargerOverVoltage

Fault

12 upsAlarmOutputOverCurrent

SNMP Trap Add

upsTrapFault upsTrapOpenFuse upsTrapCurrentLimitFault upsTrapDCBusOverCurrent upsTrapDCOverVoltage upsTrapDCBusImbalance upsTrapOutputUnderVoltage upsTrapOutputOverVoltage upsTrapHeatSinkOverheat upsTrapBypassOverload upsTrapChargerOverVoltage

Fault upsTrapOutputOverCurrent

Level

Fault

Fault

Fault

Fault

Fault

Fault

Fault

Fault

Fault

Fault

Fault

Fault

SNMP Trap Remove

upsTrapFaultClear upsTrapOpenFuseClear upsTrapCurrentLimitFaultClear upsTrapDCBusOverCurrentClea r upsTrapDCOverVoltageClear upsTrapDCBusImbalanceClear upsTrapOutputUnderVoltageCle ar upsTrapOutputOverVoltageClear upsTrapHeatSinkOverheatClear upsTrapBypassOverloadClear upsTrapChargerOverVoltage

FaultClear upsTrapOutputOverCurrentClear

54 RemotEye III User Manual – 62330-005

1600XP Alarm/Trap Table

ID Alarm Occur Message

13

14

15

16

17

18 upsAlarmInputOverVoltage

19 upsAlarmInputUnderVoltage

20 upsAlarmInputFrequencyError

21 upsAlarmBypassOverVoltage

22

23 upsAlarmDCUnderVoltAtBoostUp upsAlarmDCUnderVoltAt Charge upsAlarmBypassOverheat upsAlarmResettableInverter

Overload upsAlarmUnresettableInverter

Overload upsAlarmBypassUnderVoltage upsAlarmBypassFrequency Error

SNMP Trap Add

upsTrapDCUnderVoltAtBoostUp upsTrapDCUnderVoltAtCharge upsTrapBypassOverheat upsTrapResettableInverterOverlo ad upsTrapUnresettableInverter

Overload upsTrapInputOverVoltage upsTrapInputUnderVoltage upsTrapInputFrequencyError upsTrapBypassOverVoltage upsTrapBypassUnderVoltage upsTrapBypassFrequencyError

Level

Fault

Fault

SNMP Trap Remove

upsTrapDCUnderVoltAtBoostUp

Clear upsTrapDCUnderVoltAtCharge

Clear

Fault

Fault upsTrapBypassOverheatClear upsTrapResettableInverter

OverloadClear

Fault upsTrapUnresettableInverter

OverloadClear

Warning upsTrapInputOverVoltageClear

Warning upsTrapInputUnderVoltageClear

Warning upsTrapInputFrequencyErrorClear

Warning upsTrapBypassOverVoltageClear

Warning upsTrapBypassUnderVoltageClear

Warning upsTrapBypassFrequencyError

Clear

24 upsAlarmDCUnderVoltAtBattTest upsTrapDCUnderVoltAtBattTest Warning upsTrapDCUnderVoltAtBattTestClear

25 upsAlarmBatteryLow upsTrapBatteryLow Warning upsTrapBatteryLowClear

26 upsAlarmBatteryAtShutdown level upsTrapBatteryAtShutdownlevel Warning upsTrapBatteryAtShutdownlevel

Clear

27 upsAlarmReplaceBattery

28 upsAlarmChargerOverVoltage

Warning upsTrapReplaceBattery upsTrapChargerOverVoltage

Warning

Warning upsTrapReplaceBatteryClear

Warning upsTrapChargerOverVoltage

WarningClear

29

30

31

32

33 upsAlarmBatteryTestFailed upsAlarmBatteryDepleted upsAlarmBatteryOverheat upsAlarmSystemOverheat upsAlarmOutputOverload Warning upsTrapBatteryTestFailed upsTrapBatteryDepleted upsTrapBatteryOverheat upsTrapSystemOverheat upsTrapOutputOverloadWarning

Warning upsTrapBatteryTestFailedClear

Warning upsTrapBatteryDepletedClear

Warning upsTrapBatteryOverheatClear

Warning upsTrapSystemOverheatClear

Warning upsTrapOutputOverloadWarning

Clear

34 upsAlarmCurrentLimitWarning

35 upsAlarmAsyncOperation

36 upsAlarmServiceUPS

37

38

39 upsAlarmBatteryNear Expiration upsAlarmBatteryExpired upsAlarmDisplayCableError upsTrapCurrentLimitWarning upsTrapAsyncOperation upsTrapServiceUPS upsTrapBatteryNearExpiration upsTrapBatteryExpired upsTrapDisplayCableError

Warning

Warning upsTrapCurrentLimitWarningClear upsTrapAsyncOperationClear

Warning upsTrapServiceUPSClear

Warning upsTrapBatteryNearExpiration

Clear

Warning upsTrapBatteryExpiredClear

Warning upsTrapDisplayCableErrorClear

RemotEye III User Manual – 62330-005 55

1600XP Alarm/Trap Table

ID Alarm Occur Message

40

41

42

43

44

45

46

47

48

49

50 upsAlarmRemotEyeCommError upsAlarmRemotEyeUplink

CommError upsAlarmServicePortComm Error upsAlarmDispCommError upsAlarmSystemTestFailed upsAlarmBypassOn upsAlarmPowerFailure upsAlarmShutdownPending upsAlarmOutputOffAs Requested upsAlarmOutputOff upsAlarmBatteryTestInProgress

51 upsAlarmBatteryOn

52 upsAlarmEMDSensor1Alarm

Triggered

53

54

55

56

57

58 upsAlarmEMDSensor2Alarm

Triggered upsAlarmEMDHumidityAtLow

CiriticalPoint upsAlarmEMDHumidityAtHigh

CiriticalPoint upsAlarmEMDHumidityAtLow

WarningPoint upsAlarmEMDHumidityAtHigh

WarningPoint upsAlarmEMDTemperatureAtLow

CiriticalPoint

SNMP Trap Add

upsTrapRemotEyeCommError upsTrapRemotEyeUplink

CommError upsTrapServicePortCommError upsTrapDispCommError upsTrapSystemTestFailed upsTrapBypassOn upsTrapPowerFailure upsTrapShutdownPending upsTrapOutputOffAsRequested upsTrapOutputOff upsTrapBatteryTestInProgress upsTrapBatteryOn upsTrapEMDSensor1Alarm

Triggered upsTrapEMDSensor2Alarm

Triggered upsTrapEMDHumidityAtLow

CriticalPoint upsTrapEMDHumidityAtHigh

CriticalPoint upsTrapEMDHumidityAtLow

WarningPoint upsTrapEMDHumidityAtHigh

WarningPoint upsTrapEMDTemperatureAtLow

CriticalPoint

Level

Warning

Warning

Warning

SNMP Trap Remove

upsTrapRemotEyeCommError

Clear upsTrapRemotEyeUplink

CommErrorClear upsTrapServicePortCommError

Clear

Warning upsTrapDispCommErrorClear

Warning upsTrapSystemTestFailedClear

Info

Info

Info upsTrapBypassOnClear upsTrapPowerFailureClear

Info

Info upsTrapShutdownPendingClear upsTrapOutputOffAsRequested

Clear upsTrapOutputOffClear

Info

Info

Info

Info

Info

Info

Info

Info

Info upsTrapBatteryTestInProgress

Clear upsTrapBatteryOnClear upsTrapEMDSensor1Alarm

TriggeredClear upsTrapEMDSensor2Alarm

TriggeredClear upsTrapEMDHumidityAtLow

CriticalPointClear upsTrapEMDHumidityAtHigh

CriticalPointClear upsTrapEMDHumidityAtLow

WarningPointClear upsTrapEMDHumidityAtHigh

WarningPointClear upsTrapEMDTemperatureAtLow

CriticalPointClear

59

60

61 upsAlarmEMDTemperatureAtHigh

CiriticalPoint upsAlarmEMDTemperatureAtLow

WarningPoint upsAlarmEMDTemperatureAtHigh

WarningPoint upsTrapEMDTemperatureAtHigh

CriticalPoint upsTrapEMDTemperatureAtLow

WarningPoint upsTrapEMDTemperatureAtHigh

WarningPoint

Info

Info

Info upsTrapEMDTemperatureAtHigh

CriticalPointClear upsTrapEMDTemperatureAtLow

WarningPointClear upsTrapEMDTemperatureAtHigh

WarningPointClear

56 RemotEye III User Manual – 62330-005

1600XP Alarm/Trap Table

ID Alarm Occur Message

62 upsAlarmLogInError

SNMP Trap Add

upsTrapLogInError

Level

Info

SNMP Trap Remove

upsTrapLogInErrorClear

RemotEye III User Manual – 62330-005 57

4200FA/4300 Alarm/Trap Table

ID Alarm Occur Message

1 upsAlarmFault

2 upsAlarmOpenFuse

3 upsAlarmCurrentLimitFault

4 upsAlarmDCBusOverCurrent

5 upsAlarmDCOverVoltage

6 upsAlarmDCBusImbalance

7 upsAlarmOutputUnderVoltage

8 upsAlarmOutputOverVoltage

9 upsAlarmHeatSinkOverheat

10

11 upsAlarmUPSOverload upsAlarmChargerOverVoltage

Fault

12 upsAlarmOutputOverCurrent

13

14 upsAlarmDCUnderVoltAtBoostUp upsAlarmDCUnderVoltAtCharge

SNMP Trap Add

upsTrapFault upsTrapOpenFuse upsTrapCurrentLimitFault upsTrapDCBusOverCurrent upsTrapDCOverVoltage upsTrapDCBusImbalance upsTrapOutputUnderVoltage upsTrapOutputOverVoltage upsTrapHeatSinkOverheat upsTrapUPSOverload upsTrapChargerOverVoltage

Fault upsTrapOutputOverCurrent upsTrapDCUnderVoltAtBoostUp upsTrapDCUnderVoltAtCharge

Level

Fault

Fault

Fault

Fault

Fault

Fault

Fault

Fault

Fault

Fault

Fault

Fault

Fault

Fault

SNMP Trap Remove

upsTrapFaultClear upsTrapOpenFuseClear upsTrapCurrentLimitFaultClear upsTrapDCBusOverCurrentClear upsTrapDCOverVoltageClear upsTrapDCBusImbalanceClear upsTrapOutputUnderVoltageClear upsTrapOutputOverVoltageClear upsTrapHeatSinkOverheatClear upsTrapUPSOverloadClear upsTrapChargerOverVoltage

FaultClear upsTrapOutputOverCurrentClear upsTrapDCUnderVoltAtBoostUp

Clear upsTrapDCUnderVoltAtCharge

Clear upsTrapBypassOverheatClear 15 upsAlarmBypassOverheat

26

27 upsAlarmBatteryMCCBOff upsAlarmBypass upsTrapBypassOverheat upsTrapBatteryMCCBOff upsTrapBypass

Fault

16

17 upsAlarmInputPhaseRotationError upsAlarmBypassPhaseRotationErro r

18 upsAlarmWarning

19 upsAlarmInputOverVoltage

20 upsAlarmInputUnderVoltage

21 upsAlarmBatteryTestFailed

22 upsAlarmSystemTestFailed

23

24

25 upsAlarmBatteryLow upsAlarmBatteryAtShutdownlevel upsAlarmBatteryVoltageNotGood upsTrapInputPhaseRotationError upsTrapBypassPhaseRotationError upsTrapWarning upsTrapInputOverVoltage upsTrapInputUnderVoltage upsTrapBatteryTestFailed upsTrapSystemTestFailed upsTrapBatteryLow upsTrapBatteryAtShutdownlevel upsTrapBatteryVoltageNotGood

Fault

Fault upsTrapInputPhaseRotationErrorClea r upsTrapBypassPhaseRotationErrorCl ear

Warning upsTrapWarningClear

Warning upsTrapInputOverVoltageClear

Warning upsTrapInputUnderVoltageClear

Warning upsTrapBatteryTestFailedClear

Warning upsTrapSystemTestFailedClear

Warning upsTrapBatteryLow

Clear

Warning

Warning upsTrapBatteryAtShutdownlevelClea r upsTrapBatteryVoltageNotGoodClea r

Warning upsTrapBatteryMCCBOff

Clear

Warning upsTrapBypassClear

58 RemotEye III User Manual – 62330-005

4200FA/4300 Alarm/Trap Table

ID Alarm Occur Message

28

29

30

31

32

33

34

35

36

37

38

39

40 upsAlarmInverterOverloadWarning upsAlarmOuputOverloadWarning upsTrapInverterOverloadWarning upsTrapOutputOverloadWarning

41

42

43 upsAlarmRemotEyeUplink

CommError upsAlarmRemotEyeDownlinkCom mError upsAlarmRemotEyeUplinkCommEr ror

44 upsAlarmServicePortCommError

45 upsAlarmROMtoEEPROMError

46 upsAlarmEEPROMtoRAMError

47 upsAlarmMCCBTrip upsTrapRemotEyeUplink

CommError upsTrapRemotEyeDownlinkComm

Error upsTrapRemotEyeUplinkCommErr or upsTrapServicePortCommError upsTrapROMtoEEPROMError upsTrapEEPROMtoRAMError upsTrapMCCBTrip

48 upsAlarmEEUpdateError

49

50 upsAlarmChargerOverVoltage upsAlarmBatteryOverheat upsAlarmBatteryDepleted upsAlarmBatteryOverheat upsAlarmSystemOverheat upsAlarmCurrentLimitWarning upsAlarmAsyncOperation upsAlarmServiceUPS upsAlarmBatteryNearExpiration upsAlarmBatteryExpired upsAlarmDispCommError upsAlarmOnBypass upsAlarmPowerFailure

51 upsAlarmEPOTripped

52 upsAlarmTimedShutdown

53 upsAlarmLANShutdown

54 upsAlarmRemoteShutdown

SNMP Trap Add

upsTrapChargerOverVoltage upsTrapBatteryOverheat upsTrapBatteryDepleted upsTrapBatteryOverheat upsTrapSystemOverheat upsTrapCurrentLimitWarning upsTrapAsyncOperation upsTrapServiceUPS upsTrapBatteryNearExpiration upsTrapBatteryExpired upsTrapDispCommError upsTrapEEUpdateError upsTrapOnBypass upsTrapPowerFailure upsTrapEPOTripped upsTrapTimedShutdown upsTrapLANShutdown upsTrapRemoteShutdown

Level SNMP Trap Remove

Warning upsTrapChargerOverVoltageClear

Warning upsTrapBatteryOverheatClear

Warning upsTrapBatteryDepletedClear

Warning upsTrapBatteryOverheatClear

Warning upsTrapSystemOverheatClear

Warning

Warning upsTrapInverterOverloadWarning

Clear upsTrapOutputOverloadWarningClea r

Warning upsTrapCurrentLimitWarningClear

Warning upsTrapAsyncOperationClear

Warning upsTrapServiceUPSClear

Clear

Warning upsTrapBatteryNearExpirationClear

Warning upsTrapBatteryExpiredClear

Warning

Warning upsTrapDispCommError

Clear upsTrapRemotEyeUplink

CommErrorClear

Warning

Warning

Warning

Info upsTrapRemotEyeDownlinkCommE rrorClear upsTrapRemotEyeUplinkCommError

Clear

Warning upsTrapServicePortCommErrorClear

Warning upsTrapROMtoEEPROMErrorClear

Warning upsTrapEEPROMtoRAMErrorClear

Warning upsTrapMCCBTripClear upsTrapEEUpdateError

Clear upsTrapOnBypassClear

Info

Info

Info

Info

Info upsTrapPowerFailure

Clear upsTrapEPOTrippedClear upsTrapTimedShutdownClear upsTrapLANShutdownClear upsTrapRemoteShutdownClear

RemotEye III User Manual – 62330-005 59

4200FA/4300 Alarm/Trap Table

ID Alarm Occur Message

55 upsAlarmDelayStartup

56 upsAlarmRemoteSwitch

57 upsAlarmAutoReTransfer

58 upsAlarmProtectiveCharging

59 upsAlarmEqualizedCharging

60 upsAlarmManualMode

61 upsAlarmOutputFrequency

62 upsAlarmInverterStartup

63 upsAlarmBatteryTestInProgress

64 upsAlarmForcedBypass

65 upsAlarmLocalRun

66 upsAlarmRemoteRun

67 upsAlarmFirmwareUpdate

68 upsAlarmBypassEnable

69 upsAlarmBatteryTestDisabled

70 upsAlarmDefaultCalibration

71 upsAlarmShutdownPending

72 upsAlarmOutputOffAsRequested

73 upsAlarmOutputOff

74 upsAlarmBatteryOn

SNMP Trap Add

upsTrapDelayStartup upsTrapRemoteSwitch upsTrapAutoReTransfer upsTrapProtectiveCharging upsTrapEqualizedCharging upsTrapManualMode upsTrapOutputFrequency upsTrapInverterStartup upsTrapBatteryTestInProgress upsTrapForcedBypass upsTrapLocalRun upsTrapRemoteRun upsTrapFirmwareUpdate upsTrapBypassEnable upsTrapBatteryTestDisabled upsTrapDefaultCalibration upsTrapShutdownPending upsTrapOutputOffAsRequested upsTrapOutputOff upsTrapBatteryOn

Info

Info

Info

Info

Info

Info

Info

Info

Info

Info

Info

Info

Info

Level

Info

Info

Info

Info

Info

Info

Info

SNMP Trap Remove

upsTrapDelayStartupClear upsTrapRemoteSwitchClear upsTrapAutoReTransferClear upsTrapProtectiveCharingClear upsTrapEqualizedChargingClear upsTrapManualModeClear upsTrapOutputFrequencyClear upsTrapInverterStartupClear upsTrapBatteryTestInProgressClear upsTrapForcedBypassClear upsTrapLocalRunClear upsTrapRemoteRunClear upsTrapFirmwareUpdateClear upsTrapBypassEnableClear upsTrapBatteryTestDisabledClear upsTrapDefaultCalibrationClear upsTrapShutdownPendingClear upsTrapOutputOffAsRequestedClear upsTrapOutputOffClear upsTrapBatteryOnClear

60 RemotEye III User Manual – 62330-005

Connected Client Table

This page lists the protected registered clients of the RemotEye III that are running during the execution of the

RemotEye III Shutdown application (See Figure 34: RemotEye III Client Table Web Page). Go to section “Toshiba

RemotEye Client Software” on page 103 for more details on the software application. This page will refresh

automatically at a user-defined rate. To change or view the current refresh rate setting, select “RemotEye III

Management”

→ “HTTP Page Refresh Rates” in the RemotEye III web interface.

Figure 34: RemotEye III Client Table Web Page

Connected Client Number

This field shows the total number of RemotEye III-UPS clients running Shutdown Application Software which are presently registered with the RemotEye III. Up to 250 clients may be registered at one time.

Index

This field shows the serialized index numbers of the RemotEye III registered clients that are running during the execution of the RemotEye III Shutdown application.

IP Address

This field shows the IP addresses of the registered clients of the RemotEye III.

Client Name

This field shows the computer/Server names of the registered clients of the RemotEye III.

Connected Time

This field shows how long each registered client has been connected to RemotEye III.

Shutdown Delay

This field shows the shutdown delay of the RemotEye III registered client machines.

Note: To download the Shutdown software application please visit the following web link: http://www.toshibaups.com

UPS Management

RemotEye III User Manual – 62330-005 61

This menu contains the control parameters of the UPS system connected to the RemotEye III.

UPS Configuration General

This section shows the identification, installed date, input and output electrical parameters of the UPS. This page also allows the administrator to select which Alarm E-Mail notifications/SNMP Traps to receive.

UPS Confgiuration General

Parameter #

Object Description

This field shows the specific name to identify a particular UPS.

1600XP 4200FA 4300

1

UPS Sytem Name

  

2

3

4

5

UPS Attached Devices

UPS Instalation Date

Input Rated Voltage (V)

Ouput Rated Voltage (V)

This field allows the administrator to assign a description of load devices that attach to the UPS or to view the current setting.

This field allows the administrator to change the date the UPS was installed.

This field shows the input rated voltage of the UPS. This can be changed by the administrator.

This field shows the output rated voltage of the UPS.

6 UPS Service Comm Port Setting

This field shows the external communication port settings of the UPS.

The 4300 Series default Comm Port

Setting is set to 57600.

  

7

8

9

10

11

Input Frequency Setp when Error

Battery Rated Backup Time (Mins)

Battery in Series

Battery In Parallel

Battery Rated Ampere Hour (Ahr)

This field shows the frequency to set if the UPS cannot determine the input frequency after 3 seconds. This can be changed by the administrator. Users can only input 50.0 Hz or 60.0 Hz

This field allows the administrator to configure the estimated battery backup time (in minutes) during power failure at 100% load. The default is 0 minutes.

This field allows the administrator to configure the total number of batteries in series of the UPS system.

This field allows the administrator to configure the the total number of batteries in parallel of the UPS system.

This field allows the adminstrator to configure the Battery Rated Ampere

Hour (Ahr).

62 RemotEye III User Manual – 62330-005

UPS Alarm E-Mail/SNMP Trap Configuration

This section allows the administrator to select which faults, warnings, and informational notifications to receive via

E-mail or SNMP Traps. If a checkbox is not filled, RemotEye III will not send that particular alarm. By default, all of

the alarms are turned ON (See Figure 35: RemotEye III Selectable E-mail/SNMP Traps Notifications).

Figure 35: RemotEye III Selectable E-mail/SNMP Traps Notifications

UPS Configuration Display (Applicable to 1600XP Only)

This section shows the display parameters of the UPS.

Display Sleep Timer (Mins)

This field shows the amount of time the display will remain active before it will go to “sleep”.

Display Buzzer Mode

This field shows the Buzzer status as Enabled or Disabled.

RemotEye III User Manual – 62330-005 63

UPS Control for 1600XP

This page shows the adjustable settings of the 1600XP UPS.

Output Voltage Adjust

This field shows the manual voltage adjustment for the output of the UPS.

Range – -5 to +5 (One increment ~1Vrms)

Default Value = 0

UPS Enable RMTI-3 To Control Mode

This field shows the present mode of the control that the RemotEye III has on the UPS. This allows the RemotEye to enable or disable control the UPS Bypass and On-Line mode. It is set by the administrator.UPS Mode Change Delay

(secs)

0 – Disable

1 – Enable

Default Value = Enable

UPS Mode Change Delay (secs)

This field shows the amount of time, in seconds, before the UPS will change state.

Range – 0 to 800 seconds

Default Value = 0

UPS Mode Change Request

This field shows the mode the UPS can switch to. Users can notify the UPS to switch to Shutdown, Bypass, On-Line, using this feature. Choices are:

1- Shutdown Request

2- Bypass Request: UPS Enable RMTI-3 To Control Mode must be Enabled in order to function.

3- On-Line Request: UPS Enable RMTI-3 To Control Mode must be Enabled in order to function

Default Value = None

UPS Start Up Delay Enable

This field shows the present state of the UPS Start Up delay. It can be enabled or disabled. It is set by the administrator.

0 – Disable

1 – Enable

Default Value = Disable

UPS Start Up Delay (secs)

This field shows the time delay, in seconds, before UPS Start Up immediately following a shutdown. It is set by the administrator.

Range – 0 to 800 seconds: UPS Start Up Delay Enable must be Enabled in order to function.

Default Value = 0

UPS Start Up Delay Mode

This field shows the mode at which to enter following the start-up delay. It can either enter Bypass state or On-Line state. It is set by the administrator.

0- Bypass: UPS Start Up Delay Enable must be Enabled in order to function.

1- On-Line

Default Value = Bypass

64 RemotEye III User Manual – 62330-005

UPS Restart After Battery Shutdown Enable

This field shows the present mode set for UPS input power detection immediately after a shutdown while on batteries. It is set by the administrator.

0 – Disable

1 – Enable

Default Value = Enable

UPS Restart After Battery Shutdown Delay (secs)

This field shows the time delay, in seconds, before UPS Start Up immediately following a shutdown while on batteries. It is set by the administrator.

Range – 0 to 800 seconds: UPS Restart After Battery Shutdown Enable must be Enabled in order to function.

Default Value = 10

UPS Restart Mode

This field shows the mode at which to enter when UPS is restarted. It can either enter Bypass state or On-Line state.

It is set by the administrator.

0- Bypass: UPS Restart After Battery Shutdown Enable must be Enabled in order to function.

1- On-Line

Default Value = On-Line

UPS Auto Transfer Enable

This field shows the present mode for the auto transfer of the UPS. This allows the UPS to transfer from On-Line to

Bypass or vise-versa. It can be enabled or disabled. It is set by the administrator.

0 – Disable

1 – Enable

Default Value = Enable

UPS Auto Retransfer Delay (secs)

This field shows the time period to wait after fault occurrence before attempting transfer back On-Line. It is set by the administrator.

Range – 0 to 600 seconds: UPS Auto Transfer Enable must be Enabled in order to function.

Default Value = 3

Remote Contact Shutdown State

This field shows the present state of the remote contacts shutdown control. It can be open or closed.

0 – Open (Software Defined)

Invert Remote Contact Shutdown Logic

This field shows the logic state of the remote contact shutdown. It can be non-inverted or inverted. It is set by the administrator.

0 – Not Inverted

1 – Inverted

Default Value = Not Inverted

Remote Contact Shutdown Mode Selection

This field shows the mode of the remote contact shutdown. It is set by the administrator.

0 – Bypass

1 – Shutdown while contact closed

Default Value = Bypass

RemotEye III User Manual – 62330-005 65

Dry Contact LAN Shutdown Enable

This field shows the present mode for Dry Contact LAN Shutdown. It is set by the administrator.

0 – Disable

1 – Enable

Default Value = Enable

Dry Contact LAN Shutdown Delay (secs)

This field shows the time delay between actual event occurrence and dry contact closure. It is set by the administrator.

Range – 0 to 800 seconds: Dry Contact LAN Shutdown Enable must be Enabled in order to function

Default Value = 600

Dry Contact On Battery Delay Timer (secs)

This field shows the time delay between actual event occurrence and dry contact closure. It is set by the administrator.

Range – 0 to 800 seconds

Default Value = 10

Dry Contact Low Battery Delay Timer (secs)

This field shows the time delay between actual event occurrence and dry contact closure. It is set by the administrator.

Range – 0 to 800 seconds

Default Value = 0

66 RemotEye III User Manual – 62330-005

UPS Control for 4200FA/4300

This page shows the adjustable settings of the 4200FA/4300 UPS.

UPS Auto Restart

This field shows the mode at which to enter when UPS is restarted. It can be enabled or disabled. It is set by the administrator.

0-Disable

1-Enable

UPS Remote Bypass Switch

This field allows the user to remotely transfer the UPS to bypass. It can be enabled or disabled. It is set by the administrator.

0-Disable

1 – Enable

Note: UPS must be in On-Line mode before this feature can be enabled.

UPS Auto Retransfer

This field shows the present mode for the auto retransfer function of the UPS. It can be enabled or disabled. It is set by the administrator.

0 - Disable

1 - Enable

Battery Auto Test

This field shows the present status for the UPS battery auto test function. It can be enabled or disabled. It is set by the administrator.

0 - Disable

1 - Enable

Battery Auto Test Interval

This field shows the test interval at which UPS should automatically test the batteries. It can be set daily, weekly, or monthly. It is set by the administrator.

0 - Daily

1 - Weekly

2 - Monthly

Battery Test at Start Up

This field shows the present mode for the UPS battery test at startup function. It can be enabled or disabled. It is set by the administrator.

0 - Disable

1 - Enable

Battery Power Fail Equalize Duration (secs)

This field shows the minimum amount of time, in seconds, required for the UPS to remain in battery backup mode before it will trigger equalize charge mode.

Range - 60 to 315 seconds

Battery Start Equalize Charge

This field shows the present mode of the UPS Battery Start Equalize Charge function. It can be enabled or disabled.

It is set by the administrator.

0 - Disable

1 - Enable

RemotEye III User Manual – 62330-005 67

UPS Battery Test (Applicable to 1600XP Only)

This page shows history, results, and configuration for UPS battery test.

Last Test Start Time – Displays the date and the time when the last battery test was initiated.

Last Test Elapsed Time – Displays the duration of the battery test.

Last Test Result – Displays whether the battery test passed or failed.

Battery Test Command: o

None - No action. o

Quick Test (10 sec) - Quick test for 10 seconds. o Cancel Test - Cancel the current battery test. o

Clear Test Result - Clear the last battery test result recorded by RemotEye III.

UPS Startup Batt Test Enable

This field allows the RemotEye to force a battery test when UPS starts following a shutdown. It is enabled by the administrator.

UPS Battery Test Enable

This field allows the RemotEye to enable or disable a battery test. It is set by the administrator.

UPS Battery Test Condition Status

This field specifies the availability of the battery test feature. Note: the battery test can only be done once a day.

UPS Battery Test Schedule (Applicable only to 1600XP)

This page allows configuring the battery test schedule for the UPS.

Index

This field shows the battery test number.

Test Day

This field allows the administrator to set the day of the week that the battery test is to be performed or to view the current setting.

Test Time

This field allows the administrator to set the time that the battery test is to be performed or to view the current setting.

This value is displayed in hh:mm format.

Actions

This field shows the battery test type option.

• None – No action

• Quick Test (10 Sec) – Quick test for 10 seconds

68 RemotEye III User Manual – 62330-005

UPS Shutdown Events (Applicable to 1600XP only)

This page allows the administrator to modify the output shutdown parameters of the UPS that depends on the event.

UPS Output Shutdown Delay (secs)

This field allows the administrator to configure or view the delay (in seconds) of the UPS switching from the Run

(Inverter) mode to the Output Shutdown mode after receiving the Output Shutdown command.

The “UPS output shutdown delay” time count down will be synchronized with the output shutdown delay time

setting in the Toshiba RemotEye Client Shutdown Software program for all connected clients (See page 103

Toshiba RemotEye Client Software for more information). To avoid improper shutdown of the clients, the “UPS

output shutdown delay” time setting in the RemotEye III should always be greater than the Toshiba RemotEye

Client Shutdown Software Service program's shutdown delay setting.

UPS Event

This field column shows the event attributed to a shutdown action.

Input Power Failure – This field shows the action taken upon detection of an input power failure. Default:

Client Warning

Battery Low – This field shows the action taken upon detection of a battery low condition.

Default: Client Warning

UPS Overload – This field shows the action taken upon detection of a UPS Overload condition:

Default: Client Warning

UPS System Overheat – This field shows the action taken upon detection of a UPS over temperature condition.

Default: Client Warning

EMD Temperature Over Threshold – This field shows action taken upon detection of a EMD

Temperature Over Threshold condition.

Default: Disabled.

EMD Alarm-1 - This field shows action taken upon detection of a EMD Alarm-1 condition.

Default: Disabled.

EMD Alarm-2 – This field shows action taken upon detection of a EMD Alarm-2 condition.

Default: Disabled.

Recurring On/Off Schedule – This field shows the programmed Recurring On/Off Schedule setting.

Default: Disabled.

Non-Recurring On/Off Schedule – This field shows the programmed Non-Recurring On/Off Schedule setting.

Default: Disabled.

Action

This field allows the administrator to set a course of action to be taken in the event of a fault that are listed in the

“UPS Event” column.

Disable - Action is disabled; no action will be taken.

Client Warning - A warning message will be broadcasted to the connected clients. Note: The Toshiba RemoteEye

Client Shutdown Software has to be installed on the client.

Client Shutdown - A warning message will be broadcasted and the shutdown command will be sent to the connected clients. Note: The Toshiba RemoteEye Client Shutdown Software has to be installed on the client.

UPS Output Shutdown - A warning message will be broadcasted and the shutdown command will be sent to the connected clients, and the UPS output will be shutdown.

RemotEye III User Manual – 62330-005 69

Action Delay (mins)

This field allows the administrator to set the delay (in minutes) of the output shutdown message broadcasted or to view the current setting.

Broadcast Notification Interval (secs)

This field allows the administrator to set the broadcasted interval (in seconds) of the warning message or to view the current setting.

Recurring On/Off Schedule (Applicable only to 1600XP)

This page allows the administrator to create a recurring UPS shutdown and restart schedule. Ensure that the

Recurring On/Off Schedule option is enabled in the “UPS Shutdown Events” web menu (See UPS Shutdown Events

on page 69 for more information) in order to activate any scheduled events.

Event Index

This field shows the index numbers for the table entries.

Output Shutdown & Restart Day

This field allows the administrator to set the day of the week to output shutdown & restart the UPS, or to view the current setting. The schedules are configured in the same-day format.

Output Shutdown Time (hh:mm)

This field allows the administrator to configure the UPS output shutdown time or to view the current settings. This value is displayed in the hh:mm 24-hour format (e.g., 8:30 p.m. is 20:30).

Restart Time (hh:mm)

This field allows the administrator to configure the restart time of the UPS or to view the current settings. This value is displayed in the hh:mm 24-hour format (e.g., 8:30 p.m. is 20:30).

Note: to turn off this feature for a particular date type 99:99 in the time fields.

Non-Recurring On/Off Schedule (Applicable to 1600XP Only)

This page allows the administrator to set the output shutdown/restart for non-recurring schedule for the UPS.

Event Index

This field shows the reference number for the output shutdown/restart event.

Output Shutdown Date (mm/dd/yyyy)

This field allows the administrator to configure the specific date of the UPS output shutdown or to view the current setting.

Output Shutdown Time (hh:mm)

This field allows the administrator to set the UPS shutdown time. This value is displayed in the hh:mm 24-hour format (e.g. 8:30 p.m. is 20:30).

Restart Date (mm/dd/yyyy)

This field allows the administrator to configure the UPS restart date or to view the current setting.

Restart Time (hh:mm)

This field allows the administrator to configure the restart time of the UPS or to view the current setting. This value is displayed in the hh:mm 24-hour format (i.e. 8:30 p.m. is 20:30).

Note: to turn off this feature for a particular date type 99:99 in the time fields.

70 RemotEye III User Manual – 62330-005

Email Notification

This page allows the administrator to set the RemotEye III email notification configuration parameters.

Mail Server

This field allows the administrator to set the IP Address or Hostname of a Simple Mail Transfer Protocol (SMTP) mail server that will be used to send email messages from RemotEye III. If entering a Hostname, the Domain Name

Server (DNS) IP address is required in the DNS field.

User Account

This field allows the administrator to enter User Account login name of the SMTP mail server.

User Password

This field allows the administrator to enter User Account password of the SMTP mail server.

Note: Not all SMTP Server requires login name and password. Please check with SMTP administrator.

Domain Name

This field allows the administrator to set the domain name of the LAN for example, tic.toshiba.com.

DNS Address

This field allows the administrator to set the IP address of the network DNS server if a Hostname is entered for the

Mail Server. Otherwise, this field can be 0.0.0.0.

Mail Daily Status Report At (hh:mm)

This field allows the administrator to set the time to send a Daily Status report to the email address recipients that are selected to receive Daily Status Reports. The time is set in a 24-hour format hh:mm.

Choose the attached log data file for Daily Status Report

This field allows the administrator to select which logs to send daily to the user’s mail account which is set in the Email recipient account table.

Records Options are:

1. General Records

2. RemotEye III Events Log

3. Test Records (Not available for 4200FA/4300)

4. Backup Records

5. Fault Records

6. Operation Mode Records

7. Warning Records (Not available for 4200FA/4300)

8. System Setting Change Record (Not available for 4200FA/4300).

Choose the attached log data file for Event Status Report

This field allows the administrator to select which logs to send to the user’s mail account which set in E-mail recipient account table, when it encounters an event condition.

Records Options are:

1. General Records

2. RemotEye III Events Log

3. Test Records (Not available for 4200FA/4300)

4. Backup Records

5. Fault Records

6. Operation Mode Records

7. Warning Records (Not available for 4200FA/4300)

8. System Setting Change Record (Not available for 4200FA/4300).

E-mail Account Recipients Table

RemotEye III User Manual – 62330-005 71

The second table lists the E-mail recipients’ accounts and the level of reporting they will receive.

Mail Account

This field allows the administrator to set the E-mail address of the recipients who will receive the events or/add the daily status reports.

Description

This field allows the administrator to set the description of the recipients.

Mail Type

This field allows the administrator to select the mail type:

• None – Disable option to send email to recipients.

• Events – Current events will be sent to recipients.

NOTE: System will label each event email with the system Name and Location, in the format:

systemName@SystemLocation (“systemName” and “SystemLoaction” can be set in the RemotEye III

Configuration menu, see “RemotEye III Configuration” on page 78)

• Daily Status – Logs selected by administrator will be sent daily to the email recipients at the designated

time (See “Choose the attached log data file for Daily Status Report” on page 71).

• Events with Status – Events along with logs selected by the administrator will be sent to email recipients

when events occur (See “Choose the attached log data file for Event Status Report” on page 71).

Info Level

This field allows the administrator to select

Informational: Refers to changes in the state of the UPS. This is based on which “Informational” alarms are selected in the “UPS Configuration General” page.

Warning: UPS has encountered a non-critical abnormal condition that requires attention. This is based on which

“Warning” alarms are selected in the “UPS Configuration General” page.

Fault: UPS has encountered a critical abnormal condition and requires attention. This is based on which “Fault” alarms are selected in the “UPS Configuration General” page. Please refer to the manual for possible causes and solutions.

72 RemotEye III User Manual – 62330-005

EMD (Environmental Monitoring Device)

The Environmental Monitoring Device (EMD) is a monitoring device that provides real time comprehensive remote monitoring of environment temperature, environment humidity, and other environmental conditions via a web browser and SNMP. The EMD also provides two users defined dry contacts for additional environmental monitoring.

These dry contacts can be used with devices that provide normally-open or normally-closed results, such as door sensors, smoke detectors, motion detectors, and liquid detectors. The EMD is connected to the RemotEye III using an

Ethernet cable. One end, of the Ethernet cable, is connected to the RJ45 port of the EMD and the other end to the

“COM” port of the RemotEye III. Note: The EMD module is separate device which can be purchased from a Toshiba

UPS distributor.

EMD Installation

This section will explain the how to setup/install the EMD to RemotEye III.

1) Use the Cat5 (straight) cable and connect one end to the “010101” port on the EMD.

2) Now connect the other end of the Cat5 (straight) cable to the “COM” port of the RemotEye III.

3) Make sure that the “Communication Status” green LED blinks periodically. If the LED does not blink, verify that the Cat5 cable if functional.

5) Check the “Device Status” under the “EMD Configuration” page and make sure that it is set to “Auto” (See “EMD

Configuration” on page 75).

Figure 36: EMD RemotEye III Installation

EMD Parameter

RemotEye III User Manual – 62330-005 73

This page gives a snapshot of all EMD parameters; the parameters will be updated automatically every 5 seconds.

The text color of the parameter indicates its status based on the administrator-configurable threshold.

The list below indicates the parameter status.

• GREEN: “normal” status

Figure 37: EMD Green Web Status (Normal)

• YELLOW: “warning” status

Figure 38: EMD Yellow Web Status (Warning)

• RED: “critical” status

74

Figure 39: EMD Red Web Status (Critical)

• GREY: “unknown” value

RemotEye III User Manual – 62330-005

Figure 40: EMD Gray Web Status (Unknown)

The EMD provides the measurements for room (ambient) temperature, room (ambient) humidity, and two alarms

(two dry contacts). The warning/critical thresholds can be setup via the "EMD Setup" page.

The table Comprehensive View shows the following parameters:

EMD Name - This field displays the EMD Status as followed:

• “EMD-HT” – When the EMD is connected and working correctly.

“Disable” – Whenever the EMD is connected but the “Device Status” is disabled in the EMD configuration settings

(See “

• EMD Configuration” in page 75).

• “Unknown” – Whenever the EMD is not connected to the RemotEye III.

EMD Temperature (

°C) - This field displays the temperature in Celsius degrees.

EMD Humidity (%) - This field displays the humidity in %.

EMD Alarm-1 - This field displays the Alarm-1 status.

EMD Alarm-2 - This field displays the Alarm-2 status.

EMD Configuration

This page allows administrator to configure all necessary parameters/settings of an EMD.

Sensors

The sensors column parameters consist of the following:

1. Temperature (°C)

2. Humidity (%)

3. Alarm-1 (Sec)

4. Alarm-2 (Sec)

5. Device Status

Set Point (Low)

The low threshold(s) at which the sensor (temperature or humidity) will trigger an alarm(s). The EMD can be configured to activate at two set points on the low limit Warning, and Critical. If the checkbox is not filled, the threshold is disabled and the alarm will not be triggered. The valid range for the Temperature threshold setting is 5

°C to 65

°C, and for Humidity threshold setting is 5% to 95%.

RemotEye III User Manual – 62330-005 75

Set Point (High)

The high threshold(s) at which the sensor (temperature or humidity) will trigger an alarm(s). The EMD can be configured to activate two high set points Warning, and Critical. If the checkbox is not filled, the threshold is disabled and the alarm will not be triggered. The valid range for the Temperature threshold setting is 5

°C to 65°C, and for Humidity threshold setting is 5% to 95%.

Hysteresis

A sensors value could float around its threshold triggering multiple nuisance alarms. Setting the hysteresis will help to prevent the alarm bouncing between active and inactive. For example, if the High Warning threshold set point is

40

°C and hysteresis is 3, then the alarm will activate when the value reaches 40°C but it will not become inactive again until the sensor value reaches 37

°C.

For the contact alarm sensors (Alarm-1 and Alaarm-2), the hysteresis can be used to adjust the sensitivity of an alarm.

The alarm will be active or inactive only after the alarm stays in the same state for the duration of the hysteresis value

(in seconds). For example, if the hysteresis is 5 for an alarm, the alarm will NOT activate until the same state has persisted for 5 seconds. This ruling also applies in reverse so that the alarm has to stay in an inactive state for 5 seconds before the sensor status is recorded as normal.

Calibration Offset

If the measurement value of a sensor does not, for whatever reason, comply with the actual environment, the

“Calibration Offset” setting can be configured to adjust the final value of the sensor. For example, if a sensor reports

43% humidity for a 45% humidity environment, the administrator can configure the humidity offset as 2% so the sensor can then adjust its final value to 45%.

Alarm-1 (Sec) & Alarm-2 (Sec)

If an alarm sensor (water leak, security, etc) is connected to the EMD, the administrator can configure the alarm as

“Disabled”, “Normal Open”, “Normal Close”, “High Active”, or “Low Active”. A “Disabled” setting will mean the alarm is inactive.

“Normal Open” and “Normal Close” are used for a two-wire detector that will emulate an open/close state. When the wires are closed to “loopback” (the signal for the sensor), the sensor will detect the state as closed. The sensor will

NOT activate the alarm for 'Normal Close' in this case, although the alarm will be activated if configured as “Normal

Open”.

“High Active” and “Low Active” can be configured when a “contact closure” type detector is attached. The administrator should connect the wire to the right side of the alarm (marked as arrow-in), and 8 to 12 VDC should be able to be detected by the EMD as “high” state.

Device Status

The EMD can be configured as “Disabled” or “Auto”. The setup should be configured as “Disabled” if an EMD is not attached to the port or would like to turn of the EMD feature. The EMD type will be auto detected by the

RemotEye III if configured as “Auto” and if the EMD is plugged into the COM port.

76 RemotEye III User Manual – 62330-005

RemotEye III Management

This menu allows the administrator to view the RemotEye III settings/control parameters. The security levels are as followed: Users have read-only privileges, whereas the administrators have read/write access.

Date and Time

This page shows the Date & Time options setting/parameters for RemotEye III.

Date On RemotEye III (mm/dd/yyyy)

This field show the current date stored in the RemotEye III. Please see the following sections that explain how to change RemotEye III’s date. The date value is displayed in the MM/DD/YYYY format (i.e., Aug 18, 2012 is

08/18/2012).

Time On RemotEye III (hh:mm:ss)

This field shows the current time stored in the RemotEye III. Please see the following sections that explain how to change RemotEye III’s time. The time value is displayed in the hh:mm:ss 24-hour format (i.e., 8:30 p.m. is 20:30:00).

Synchronize with computer time (Computer Date & Computer Time)

If this option is selected, the administrator is allowing the RemotEye III’s date and time to be synchronized with the end user’s computer date and time.

Synchronize with NTP Server (IP Address)

If this option is selected, an NTP (Network Time Protocol) server IP address must be entered and select the correct time zone to activate this option. After configuration, the RemotEye III will synchronize its time and date with the server periodically.

Set Manually (Date (mm/dd/yyyy) & Time (hh:mm:ss))

If this option is selected, will allow the administrator to configure the RemotEye III’s date and time manually,

Time Zone

This field allows the administrator to set the local time zone and compensate for Daylight Savings Time when setting the RemotEye III date and time manually or via an NTP server.

RemotEye III User Manual – 62330-005 77

RemotEye III Configuration

This page shows the configurable settings/parameters of the RemotEye III.

RemotEye III Software Revision

This field shows the software revision of RemotEye III.

RemotEye III Hardware (MAC) Address

This field shows the RemotEye III MAC address. MAC address format is 00 E0 D8 XX XX XX.

RemotEye III IP Address

This field allows the administrator to set the IP address of the RemotEye III or to view the current setting (i.e.,

192.168.1.20).

RemotEye III Gateway Address

This field allows the administrator to set the IP address of the gateway or to view the current setting (i.e.,

192.168.1.1). This is used to allow the RemotEye III to communicate to another network. If no gateway is used,

0.0.0.0 can be entered to this field.

RemotEye III Subnet Mask

This field allows the administrator to set the subnet mask of the RemotEye III or to view the current setting (i.e.,

255.255.255.0). This identifies the network address that the RemotEye III belongs too.

RemotEye III Installation Date

This field shows the date the RemotEye was installed.

RemotEye III Install Status

This field notifies to the UPS that an external device is connected to the UPS.

RemotEye III Data Link

This field will display two different possibilities between RemotEye III and the UPS:

• Link Down: Disconnected

• Link Up: Connected

RemotEye III Network Link

This field will display two different possibilities between RemotEye III and the Network:

• Link Down: Disconnected

• Link Up: Connected

RemotEye III Polling Rate (secs)

This field allows the administrator to set the time interval of the RemotEye III updates that are received from the

UPS.

RemotEye III Baud Rate (bps) (Not avilable for the 4200FA/4300)

This field shows the data transmission rate between the UPS and the RemotEye III.

RemotEye III General Records Logs Frequency (secs)

This field allows the administrator to set the polling time (in seconds) of the Input Voltage, Output Voltage, Output

Load, Battery Voltage, Input Frequency, and the UPS Output Source. The readings will be stored into the UPS history log. The longer the polling rate the longer the time frame of records.

RemotEye III System Name

This field allows the administrator to set the value in System name that is defined in MIB-II or to view the current setting. This string also serves as the RemotEye III Client Identifier (CID) in DHCP systems (e.g.

SystemName.tic.toshiba.com)

78 RemotEye III User Manual – 62330-005

RemotEye III System Contact

This field allows the administrator to set the value in System Manager (System Contact) that is defined in MIB file or to view the current setting.

RemotEye III System Location

This field allows the administrator to set the value in System installation place (System Location) that is defined in

MIB file or to view the current setting.

NOTE: System will label each event email with the system Name and Location, in the format: systemName@SystemLocation

RemotEye III User Manual – 62330-005 79

RemotEye III Control

This page allows the administrator to Enable/Disable the available RemotEye III communication protocols. In addition, it allows the administrator to restart or reset (default settings) the RemotEye III.

RemotEye III DHCP Control

This field allows the administrator to Enable/Disable the Boot Protocol (BootP)/Dynamic Host Configuration

Protocol (DHCP) support or to view the current settings. These protocols are Internet standards and are used to obtain a dynamic IP address from a BootP/DHCP server.

RemotEye III Telnet Control

This field allows the administrator to Enable/Disable the terminal-to-server application (Telnet) control process (i.e., telnet 192.168.1.20).

RemotEye III TFTP Network Upgrade Control

This field allows the administrator to Enable/Disable the Trivial File Transfer Protocol (TFTP) upgrade control or to

view the current setting. The Windows firmware upgrade utility, Tugrade (See “Network Firmware Upgrade Tool” on page 14), is used to upgrade the RemotEye III to the latest firmware when enabled.

SNMP Version

This field allows the administrator to enable and disable the Simple Network Management Protocol security level.

When enabled, administrators have the option to set for SNMPv1 or SNMPv3.

HTTP(s) Autehnication

This field allows the administrator to select from Local User or RADIUS. If “Local User” is selected, the user will be authenticated by the RemotEye III stored credentials. If “RADIUS” is selected, the RemotEye III will communicate with a RADIUS server to verify the user’s credentials.

RemotEye III Reset to Default

This field allows the administrator to Enable/Disable the RemotEye III Reset function. When enabled, all parameters in the RemotEye III will be reset to default setting (includes network settings, password, etc.).

RemotEye III Restart

This field allows the administrator to Enable/Disable the RemotEye III Restart function. When enabled, the

RemotEye III may be restarted.

80 RemotEye III User Manual – 62330-005

RADIUS Configuration

This page allows the administrator to input the RADIUS server parameters. RADIUS is networking protocol that provides a centralized authentication to use its network service. The RemotEye III has the ability to communicate with a RADIUS server which will determine if the user has access to RemotEye III services. Here are the parameters required to enable the Radius feature:

RADIUS UDP Port

This field shows the default UDP port for RADIUS Authentication. (Read-Only)

Primary RADIUS Server

This field allows the administrator to set the IP address of the primary RADIUS server.

Secondary RADIUS Server

This field allows the administrator to set the IP address of the secondary RADIUS server, in case the primary server does not respond.

Share Secret of Primary Server

This allows the administrator to input the case-sensitive text sting (password) into the text field to access the

RADIUS server.

Share Secret of Secondary Server

This allows the administrator to input the case-sensitive text sting (password) into the text field to access the

RADIUS server.

Packet Timeout Interval (sec)

User can set the Packet Timeout Interval in seconds.

Packet Retry Times

User can set the packet retry times.

Modbus TCP Configuration

Node ID

Node ID can be any number from 1 to 255.

Port Number

Default Modbus TCP port number is 502.

SNMP TRAP Receivers

This page lists the parameters for SNMP trap receivers (for SNMP Network Management).

Index

This field shows the index numbers for the table entries (8 Max).

IP Address

This field allows the administrator to set the IP Address of the NMS station to which the traps should be sent or to view the current setting.

Community String

This field allows the administrator to set the community string of the trap's PDU (Protocol Data Unit) to be sent or to view the current setting. The maximum length of the string is 19 characters.

Trap Type

This field allows the administrator to set the types of traps to be received or to view the current settings.

Setting options are:

None: The specified NMS will not receive traps.

Toshiba Trap: Traps are received based on the Toshiba MIB.

RemotEye III User Manual – 62330-005 81

JEMA Trap: Traps are received based on the JEMA MIB.

IETF Trap: Traps are received based on the RFC 1628 MIB.

Info Receiving Severity level

Informational: Refers to changes in the state of the UPS. Please see UPS manual for additional information

Warning: UPS has encountered a noncritical abnormal condition that requires attention. Please refer to the UPS manual for possible causes and solutions.

Fault: UPS has encountered a critical abnormal condition that requires attention. Please refer to the UPS manual for possible causes and solutions. If more information is needed or additional assistance is required, contact Toshiba authorized service center for Service.

Description

This field shows the administrator description string (text).

SNMP Communities /HTTP Access Control

This page displays a list of the Network Management Stations (NMS) that have RemotEye III read or write access.

Index

This field shows the index numbers for the table entries (8 Max).

NMS IP Address

This field allows the administrator to set the management station's IP address or to view the current settings.” 0.0.0.0” means entry not configured. (i.e., an entry of 192.168.1.255 indicates clients with IP address within the range of

192.168.1.0 to 192.168.1.255 are valid network management stations set by the user).

Community String

This field allows the administrator to set the low level password of the associated IP address or to view the current setting.

Note: An entry of 255.255.255.255 grants the user access rights to all IP addresses.

Access Mode

This field allows the administrator to set the access type for the client machines (NMS) or to view the current setting.

• No Access

• Read Only

• Read/Write

HTTP Page Refresh Rates

This page allows the administrator to set the HTTP page refresh interval rate (in seconds) of the following pages or to view the current setting.

• Comprehensive Page (secs)

• Input Parameter (secs)

• Output Parameter (secs)

• Bypass Parameter (secs)

• DC Bus Parameter (secs)

• Battery Parameter (secs)

• Alarm Table (secs)

• Connected Client Table (secs)

82 RemotEye III User Manual – 62330-005

History Data & Logs

This menu allows the user to view UPS & RemotEye III log messages, such as the UPS History Summaries. The log messages are displayed in chronological order and are used to help detect and diagnose UPS problems with the

RemotEye III.

UPS History Summary

This page shows various UPS historical information. This information is based on the data accumulating since the start of the UPS

UPS History System Operation Time (Secs)

This field specifies how long the UPS has been operating (includes On-Line, Bypass, Backup) in seconds.

UPS History Inverter Operation Time (Secs)

This field specifies how long the UPS has been running in Inverter (On-Line) mode in seconds.

UPS History Backup Operation Time (Secs) (Not available for 4200FA/4300)

This field specifies how long the UPS has been running in battery backup mode in seconds.

UPS History Lifetime Remaining (Month) (Not available for 4200FA/4300)

This field specifies the remaining lifetime of the UPS in month.

UPS History Highest System Temp (

°C) (Not available for 4200FA/4300)

This field shows the highest system temperature recorded of the UPS in Celsius.

UPS History Highest Battery Temp (Not available for 4200FA/4300)

This field shows the highest battery temperature recorded of the UPS in Celsius.

UPS History Total Number Input Under Voltage (Not available for 4200FA/4300)

This field shows the total number of times the UPS has entered under voltage state.

UPS History Total Number Overload (Not available for 4200FA/4300)

This field shows the total number of times the UPS has overloaded.

UPS History Total Number Test (Not available for 4200FA/4300)

This field shows the total number of tests that has been conducted on the UPS.

UPS History Total Number Backup

The field shows the total number of times the UPS has switched to battery backup mode.

UPS History Total Number Faults

This field shows the total number of faults the UPS has encountered.

UPS History Total Number Operation Mode Change

This field shows the total number of operational mode change the UPS has encountered.

UPS History Total Number Warnings (Not available for 4200FA/4300)

This field shows the total number of warnings the UPS has encountered.

UPS History Total Number System Settings Changed (Not available for 4200FA/4300)

This field shows the total number of UPS system setting changes the UPS has encountered.

UPS History Total Number Resets (Not available for 4200FA/4300)

This field shows the total number of resets occurred on the UPS.

RemotEye III User Manual – 62330-005 83

General Records

This page lists the fundamental UPS parameters. Consolidation intervals may be changed by the administrator by

modifying the variable General Records Log Frequency from the RemotEye III Configuration page (See “RemotEye

III General Records Logs Frequency (secs)” on page 78). The existing values are overwritten when the maximum

number of entries has been reached. The log data may be cleared from the Clear & Save Log Data menu (See “Clear

& Save Log Data” on page 90).

General Records Log Index Page

This index lists the system status records as a series of blocks each containing up to 32 records. Each block is named

“From (date) (time) To (Date) (Time).” The RemotEye will record up to a maximum of 1870 records, and then each additional new record will replace the oldest stored General Record.

Click on any index listing to see the UPS History Log Data Table for that period.

The 1600XP General Records Log Data Table has the following headings:

• Log Date (mm/dd/yyyy) - This field shows the date of the recording

• Log Time - This field shows the time that the values were recorded. Time is displayed in the hh:mm:ss 24hour format (i.e., 8:30 p.m. is 20:30:00).

• Input Voltage (V)

• Input Frequency (Hz)

• Output Voltage (V)

• Battery Voltage (Vdc)

• Output Status

• Output Frequency (Hz)

• Output Current (Amps)

The 4200FA/4300 General Records Log Data Table has the following headings:

• Log Date (mm/dd/yyyy) - This field shows the date of the recording

• Log Time - This field shows the time that the values were recorded. Time is displayed in the hh:mm:ss 24hour format (i.e., 8:30 p.m. is 20:30:00).

• Input Voltage (V) (V1, V2, V3)

• Input Power (%)

• Output Voltage (V) (V1, V2, V3)

• Battery Voltage (Vdc)

• Output Status

• Output Power Total (%)

• Output Current Total (%)

Test Records (Applicable to 1600XP Only)

This table lists the detail history of test that has occurred on the UPS. The Log can store a maximum of 680 records.

If more events are recorded, the new record replaces the oldest record.

1. Log Date – This field shows the date of the recording.

2. Log Time - This field shows the time that the values were recorded. Time is displayed in the hh:mm:ss 24hour format (i.e., 8:30 p.m. is 20:30:00).

3. Record Number - Maximum number of records is 255.

84 RemotEye III User Manual – 62330-005

4. System Input Type

5. System Output Type

6. Input Voltage (%)

7. Output Voltage (%)

8. Output Load (%)

9. DC Input Voltage (%)

10. Battery Voltage

11. Test Type

12. RSV

13. PASS

14. Trigger Source

Backup Records

This table lists the detail history of backup that has occurred on the UPS. The Log can store a maximum of 680 records. If more events are recorded, the new record replaces the oldest record.

1600XP Backup Record Log Format

• Log Date – This field shows the date of the recording.

• Log Time - This field shows the time that the values were recorded. Time is displayed in the hh:mm:ss 24hour format (i.e., 8:30 p.m. is 20:30:00).

• Record Number - Maximum number of records is 255.

• System Input Type

• System Output Type

• Input Voltage (%)

• Output Voltage (%)

• Output Load (%)

• DC Input Voltage (%)

• Battery Voltage start (%)

• Battery Voltage end (%)

• Trigger Source

• Backup Duration

4200FA/4300 Backup Record Log Format

• Log Date – This field shows the date of the recording.

• Log Time - This field shows the time for backup record. Time is displayed in the hh:mm:ss 24-hour format

(i.e., 8:30 p.m. is 20:30:00).

• Record Number - Maximum number of records is 255.

• VBAT End – Battery Voltage recorded at the end of the event.

• Factor – Description of the event that occurred.

• Backup Time (Sec) – The amount of the time the UPS remained in battery backup.

Fault Records

This table lists the detailed history of faults that have occurred on the UPS. The Log can store a maximum of 680 records. If more events are recorded, the new record replaces the oldest record.

1600XP Fault Records Log Format

• Log Date – This field shows the date of the recording.

• Log Time - This field shows the time that the values were recorded. Time is displayed in the hh:mm:ss 24hour format (i.e., 8:30 p.m. is 20:30:00).

RemotEye III User Manual – 62330-005 85

• Record Number - Maximum number of records is 255.

• System Input Type

• System Output Type

• Input Voltage

• Output Voltage

• Output Load

• DC Input Voltage

• Battery Voltage

• Slot Location

• Fault

4200FA/4300 Fault Records Log Format

• Log Date – This field shows the date of the recording.

• Log Time - This field shows the time that the values were recorded. Time is displayed in the hh:mm:ss 24hour format (i.e., 8:30 p.m. is 20:30:00).

• Record Number – Maximuan number of record is 255.

• Fault 1 – Description of fault detected.

• Fault 2 – Description of fault detected.

Following is a table of the possible UPS fault codes and their meanings. Please refer to UPS manual for more specific details.

Fault Code

FSOPEN

CL

DCOC

DCOV

DCIB

VOUV

VOOV

DVCOH

BYPOL

CHRGOV

OOC

DCUVBS

DCUVC

BYPOH

INVOLRSTAOK

INVOLRSTNOK

OH

DCUB

OL

PHIRER

PHBRER

EPO

Description

Fuse opened

Current limit fault occurred

DC bus over current fault occurred

DC bus over voltage occurred

DC bus imbalance occurred

Output voltage undervoltage occurred

Output voltage overvoltage occurred

Device overheat occurred

Bypass overload occurred

Charger overvoltage occurred

Output overcurrent occurred

DC bus under voltage occurred at boostup UPS state

DC bus under voltage occurred at charging of UPS state

Bypass overheat occurred

Inverter overload occurred and it is resettable

Inverter overload occurred and it is NOT resettable

UPS Overheat

DC Imbalance

UPS Overlaod

Phase Error

Bypass Phase Error

Emergency Power Off

Table 2: UPS Fault Codes

Operation Mode Records

86 RemotEye III User Manual – 62330-005

This table lists the detail history of operation mode changes that has occurred on the UPS. The Log can store a maximum of 680 records. If more events are recorded, the new record replaces the oldest record.

1600XP Operation Mode Records Log Format

• Log Date – This field shows the date of the recording.

• Log Time - This field shows the time that the values were recorded. Time is displayed in the hh:mm:ss 24hour format (i.e., 8:30 p.m. is 20:30:00).

• Record Number - Maximum number of records is 255.

• System Input Type

• System Output Type

• Input Voltage (%)

• Output Voltage (%)

• Output Load (%)

• DC Input Voltage (%)

• Battery Voltage (%)

• From

• To

• Branch (Used for Technical Support)

• Cause (Used for Technical Support)

4200FA/4300 Operation Mode Records Log Format

• Log Date – This field shows the date of the recording.

• Log Time - This field shows the time that the values were recorded. Time is displayed in the hh:mm:ss 24hour format (i.e., 8:30 p.m. is 20:30:00).

• Record Number – Maximaum Number of records is 255.

• Next – State of the UPS.

o

• Condition 1: List of possible conditions:

conditions: o

Input voltage undervoltage o

Input voltage overvoltage o Input voltage out of spec o

Bypass Voltage Undervoltage o

Bypass Voltage Overvoltage o

Output Voltage Undervoltage o

Output Voltage Overvoltage o

DC Bus Undervoltage

• Condition 2: List of possible conditions: o

DC bus out of spec o

Battery Voltage low o

Battery voltage reached shutdown level o Power Failure o

DC Bus low o Battery voltage out of spec

List of

• Status: List of possible conditions: o

Input Frequency Detection o

Input Phase Rotation Error o

Input Frequency Error

RemotEye III User Manual – 62330-005 87

o Feedback Detection o

Bypass Phase Rotation Error o

Feedback Error o

Output Frequency Detection o Synchronous

Warning Records

This table lists the detail history of warnings that has occurred on the UPS. The Log can store a maximum of 680 records. If more events are recorded, the new record replaces the oldest record.

1600XP Warning Records Log Format

• Log Date – This field shows the date of the recording.

• Log Time - This field shows the time that the values were recorded. Time is displayed in the hh:mm:ss 24hour format (i.e., 8:30 p.m. is 20:30:00).

• Record Number - Maximum number of records is 255.

• System Input Type

• System Output Type

• Input Voltage (%)

• Output Voltage (%)

• Output Load (%)

• DC Input Voltage (%)

• Battery Voltage (%)

• Slot Location

• Warning

4200FA/4300 Warning Records Log Format

• Log Date – This field shows the date of the recording.

• Log Time - This field shows the time that the values were recorded. Time is displayed in the hh:mm:ss 24hour format (i.e., 8:30 p.m. is 20:30:00).

• Record Number - Maximum number of records is 255.

• System Input Type

• System Output Type

• Input Voltage (%)

• Output Voltage (%)

• Output Load (%)

• DC Input Voltage (%)

• Battery Voltage (%)

• Slot Location

• Warning

Following is a table of the possible UPS warning codes and their meanings.

88 RemotEye III User Manual – 62330-005

Warning Code

CL

ASYN

CALL

BATLFNEAR

BATLFEND

DCER

REYEERR

REYEUPERR

RS232ERR

DCANERR

SYSTSTFAIL

VIOV

VIUV

FIERR

VBYPOV

VBYPUV

FBYPERR

DCUVBST

VBATLOW

VBATSD

BATRPL

CHRGOV

BTSTFAIL

BATDEPL

BATOH

SYSOH

OL110

Description

Current limit occurred

Input and output are not synchronized

UPS needs servicing

Battery life near to end

Battery life end

Display cable error occurred

RemotEye communication error (RS232)

RemotEye communication error (NET)

Service port communication error

Display CAN communication error

System test fail

Input over voltage occurred

Input under voltage occurred

Input frequency error occurred

Bypass overvoltage occurred

Bypass undervoltage occurred

Bypass frequency error occurred

DC bus uvdervoltage at battery test

Battery voltage low

Battery voltage has reached shutdown level

Battery replace event occurred

Charger overvoltege occurred

Battery test failed

Battery depleted

Battery overheat occurred

System overheat occurred

Overload occurred

Table 3: UPS Warning Codes

RemotEye III User Manual – 62330-005 89

System Setting Change Record (Applicable to 1600XP Only)

This table lists the detail history of system changes that has occurred on the UPS. The Log can store a maximum of

680 records. If more events are recorded, the new record replaces the oldest record.

• Log Date – This field shows the date of the recording.

• Log Time - This field shows the time that the values were recorded. Time is displayed in the hh:mm:ss 24hour format (i.e., 8:30 p.m. is 20:30:00).

• Record Number - Maximum number of records is 255.

• System Input Type

• System Output Type

• Input Voltage (%)

• Output Voltage (%)

• Output Load (%)

• DC Input Voltage (%)

• Battery Voltage (%)

• Block

• Item

• Written

• Trigger Source

RemotEye III Events Log

This table lists the RemotEye III events since the table was last cleared. If changes have been made by the administrator, it will display if it was made through “Telnet” or “HTTP” communication following with the IP address of the user. The existing values are overwritten when the maximum number of entries has been reached.

• Event Date

• Event Time

• Event Description

Clear & Save Log Data

This allows the administrator to save the RemotEye III log data to a file. The saved files are given a .csv extension, which allows it to be opened using Microsoft© Excel. Specific log data may be cleared by the administrator or the entire log data record may be cleared after saving the .csv file.

Clear Log Data

This field allows the administrator to the clear log data by checking the applicable box and clicking the Clear button.

Clear Log Data after saving the log file

The log data may be cleared after saving the file as a .CSV file by clicking YES at the Clear Log Data after saving the log radio button.

Save Log Data

The log data may be saved as a .CSV file by clicking General Records, RemotEyeIII Events Log, UPS Events

Log, Test Records, Backup Records, Fault Records, Operation Mode Records, Warning Records or System

Setting Change Record.

Note: If the option “Clear Log Data after saving the log file” is selected, once the “Save Log Data” is clicked, the clear log function will be performed even if the user cancels the “Save Log Data” action. To clear any of the logs, must be logged in as an administrator.

90 RemotEye III User Manual – 62330-005

These are the available logs for the 4200FA/4300 UPS:

General Records

Operation Mode Records

Backup Records

RemotEye III Events Log

Fault records

Figure 41: 4200FA/4300 Clear and Save Log Data

RemotEye III User Manual – 62330-005 91

These are the available logs available for the 1600XP UPS:

General Records

Fault records

Test Records

Operation Mode Records

System Setting Change Record RemotEye III Events Log

Backup Records

Warning Records

Figure 42: 1600XP Clear and Save Log Data

92 RemotEye III User Manual – 62330-005

Managing the UPS Via Java

The RemotEye III provides real-time graphical user interfaces written in Java Applet to provide a means to monitor a

Toshiba UPS over a LAN or a WAN.

• Monitor — Displays the UPS key parameters graphically.

• History — Displays the UPS history log graphically.

Monitor

Clicking the Monitor button at the top-left side of the RemotEye III home page will open the UPS Monitor screen in a

separate window (See Figure 43: RemotEye III Web Interface Buttons).

Figure 43: RemotEye III Web Interface Buttons

The Monitor applet provides a visual representation of the UPS system. It contains a status bar that can display the current UPS status, an alarm window that can display the current UPS alarms, and a display of the following UPS key

parameters (See Figure 44: HTTP Monitor Screen):

System Name

Date and Time

UPS Model

Input Voltage, Input Frequency

Output Voltage, Output Frequency UPS Load

UPS Output Estimated Battery Backup Time

Operation Status Alarm Status

Serial Number

UPS Temperatures

Battery Voltage

Battery Backup Operation

Communication Status

Figure 44: HTTP Monitor Screen

RemotEye III User Manual – 62330-005 93

History

Clicking the History button at the top-left side of the RemotEye III home page (See Figure 43: RemotEye III Web

Interface Buttons), Figure 45: HTTP History Data Screen on page 94 will open in a separate window. This screen

displays the UPS history log as a line graph. By default, all of the UPS parameters will be displayed on the same graph. The user may select any combination of parameters to be displayed on the graph by clicking the check box beside a parameter on the monitor screen and clicking the Refresh button.

• Display Point — Displays the log interval on the graph.

• Refresh — Click the Refresh button after changing any settings on the History page for the changes to take effect.

• Reload — Updates the History page and resets the right display margin.

• Exit — Closes the History window

Refresh Reload Exit

Figure 45: HTTP History Data Screen

94 RemotEye III User Manual – 62330-005

Configuring the Remoteye III via SNMP

The RemotEye III supports SNMP. Any workstation with SNMP management software can manage/monitor a

Toshiba UPS through RemotEye III.

Note: This section will focus entirely on RemotEye III operation.

System Requirements

There are two components of an SNMP system: an Agent and a Manager. The Agent collects information about a network node. The Manager collects information from the Agent.

The RemotEye III provides an Agent for a Toshiba UPS (1600XP, 4200FA, or 4300). The Manager is a software application that is provided separately. A workstation running Manager Software is considered a Network

Management Station (NMS).

There are many Manager Applications available. Some commonly used applications are listed below:

• RemotRadar V3.00 (Visit www.ToshibaUPS.com

for more information)

• Cabletron Spectrum

• DEC Polycenter

• HP OpenView

• IBM NetView

• Novell Managewise

• SunNet Manager

Preliminary Issues

There are several pieces of information to collect before setting up the RemotEye III and an NMS. As a bare minimum, know the following prior to system setup:

• The IP Address of the RemotEye III.

• The Gateway Address of the RemotEye III.

• The IP Address of the Network Management Station.

RemotEye III (Agent) Settings

Before using the RemotEye III in an SNMP environment, the RemotEye III must be programmed to coordinate with a particular NMS.

Examining Network Pathway

Several RemotEye III parameters determine the networks available for RemotEye III data transmission. These parameters are the IP Address, the Gateway Address, and the MIB System Group.

The IP Address of RemotEye III must place it on the same network as the NMS. If the two elements are not located on the same network, a gateway between the RemotEye III and the NMS must exist.

The Gateway Address indicated in RemotEye III must identify a network device providing access to the network of

the NMS. For instruction on defining which gateway RemotEye III uses, consult the System Group section on page

27.

The MIB System Group of RemotEye III must match that of the NMS (see the section titled System Group on page

27 for further information). This parameter will allow an NMS within the group to access RemotEye III data.

RemotEye III User Manual – 62330-005 95

Granting Write Access

The RemotEye III controls permissions for workstations. Any workstation attempting to alter UPS parameters through RemotEye III must have permission.

By default, the RemotEye III will allow any workstation the ability to write new configuration information to

RemotEye III and its attached Toshiba UPS. This is accomplished through SNMP “sets” using the default read/write community string.

To restrict access to only NMS machines, the SNMP Communities and Control Group of RemotEye III must be

programmed accordingly. See the section entitled SNMP Communities on page 32 for details on adding workstations

to the SNMP Communities.

If the IP address of the NMS is not added to the SNMP Communities with Read/Write permissions, the NMS software can only read the status of the UPS, and changes to UPS parameters will be prohibited.

NMS (Manager) Settings

There are two areas of consideration when coordinating an NMS with a RemotEye III. First, the Manager software on the NMS must be prepared to handle the RemotEye III Management Information Base (MIB), and second, the

Manager must be configured to receive any traps the RemotEye III sends.

Importing the MIB File

The MIB file is contained on the included CD-ROM. This file describes the information that is attainable from a

Toshiba UPS.

The Toshiba MIB file must be manually entered (imported or compiled) into the Manger database. For instruction on incorporating private MIB files into the Manager, consult the Manager Software documentation.

MIB Import Example

This example shows how to incorporate the Toshiba MIB into the Manager application HP OpenView Workgroup

Node Manager. The software runs on the Windows platform.

Launch HP OpenView Workgroup Node Manager.

From the Control pull down menu, click SNMP Manager

→ Manage Database → Select → (map to the MIB file,

ToshibaRMTI3.mib, on the included CDROM)

→ click ADD.

Click “Close” to close the SNMP Manager Database.

Specifying Trap Receivers

To send traps to an NMS, the NMS must be designated as a trap receiver of the RemotEye III. See Trap Receiver

Table section on page 34 for instruction on defining a trap receiver.

Configuring the Trap Receiver

The trap handler of a Manager application varies between software developers. For specific information about a trap handler, consult the Manager Software documentation.

Follow the following steps to setup trap receivers.

96 RemotEye III User Manual – 62330-005

1. Open RemotEye III on internet browser and go to RemotEye III Management -> RemotEye III Control to check

SNMP version

Figure 46: SNMP Version Menu

2. Go to RemotEye III Management -> SNMP TRAP Receivers and Become Administrator

Figure 47: SNMP Trap Receivers Menu

RemotEye III User Manual – 62330-005 97

3. Enter trap receiver IP address and select Trap Type as Toshiba or JEMA or IETF then set value.

Figure 48: SNMP Trap Type Menu

98 RemotEye III User Manual – 62330-005

Trap Example

Following shows an example of a trap trigger by Battery Test Command as “Quick Test (10 Sec)”. Note: Battery Test feature not available for 4200FA/4300 Series UPS.

Figure 49: RemotEye III Trap Example

User will receive battery test in progress trap

Figure 50: SNMP Trap Example

Note: If SNMP version is SNMPv1, SNMP tool must be SNMPv1 compatible.

RemotEye III User Manual – 62330-005 99

Connecting to the RemotEye III via SNMP

Executing SNMP Gets and Sets

Besides receiving traps, an NMS can perform the valuable functions of SNMP gets and sets through RemotEye III.

An SNMP get entails retrieving information. This is a request from a Manager to an Agent for information the Agent has collected.

An SNMP set entails configuring a device parameter. This is a command from a Manager to an Agent instructing the

Agent to change some setup parameter. The setup parameter may apply to the agent or the agent’s network device for which it is responsible.

SNMP Get/Set Criteria

Successful SNMP gets and sets from an NMS depend upon RemotEye III settings. The RemotEye III acts as a shield, refusing access to machines that do not meet its setup criteria. If the RemotEye III provides an NMS with

Read access, SNMP gets are allowed, if RemotEye III provides NMS with Write access, both SNMP gets and SNMP sets are allowed.

The RemotEye III uses the community values listed in the RemotEye III Control Group and the entries listed in the

SNMP Communities to render get/set requests from network machines. The evaluation techniques are described in the following sections.

NMS Unlisted in SNMP Communities

If an NMS is not listed in the SNMP Communities, the global RemotEye III communities are used for evaluation.

The global communities are set within the Control Group table of the RemotEye III. If a get request matches either the Community Read-Only or the Community Read/Write values, the request is honored. A set, however, is only allowed if the request includes the Community Read/Write value.

NMS Listed in SNMP Communities

If the NMS appears in the SNMP Communities with Read or Read/Write Access rights, the corresponding community name and privileges listed within this table, in conjunction with the global community values, are used to evaluate the request.

If the NMS community listing matches any of the global communities, the SNMP Communities table listing will override the permissions established by the global listings. First, the SNMP Communities entry negates both global values, and second, the permissions for this entry will apply to requests from the NMS.

If the NMS appears in the SNMP Communities multiple times, using the same community, the entry with the highest priority (lowest line number) is used to evaluate the request though this community name.

If a NoAccess listing for the NMS appears anywhere in the table, the permissions assigned by the global community names are negated. Any request from the NMS using the global community names will be refused. In addition, only

SNMP Communities entries with higher priority are applicable. To complete SNMP get or sets from this NMS, an entry above the NoAccess line must assign the NMS Read or Read/Write permissions.

If the highest priority listing for an NMS in the SNMP Communities labels the machine with access rights as

NoAccess, no get/set requests from this machine, regardless of its community string, are permitted.

SNMP Get/Set Examples

The following scenarios can be used to provide guidelines when configuring RemotEye III. In all the examples, assume the Control Group settings are:

Community Read-Only: ronly

Community Read/Write: rwrite

Also, assume the NMS has the IP Address 172.18.63.1.

Case #1: NMS is not listed in the SNMP Communities

Assume the SNMP Communities Table is empty.

100 RemotEye III User Manual – 62330-005

Analysis: Any NMS get request will be honoured when using ronly or rwrite community string. Any NMS set requests will be honoured only when using rwrite community string.

Case #2: NMS is listed in SNMP Communities with additional community strings

SNMP Communities settings:

[1] 172.18.63.1 foobar Read/Write

[2] 172.18.63.1 reading Read

Analysis: Get requests from the NMS with IP 172.18.63.1 will be honoured when using the reading, foobar, rwrite or the ronly community strings. The NMS will have set ability when using either the foobar or the rwrite community strings.

Case #3: NMS is listed in the SNMP Communities using one of the global community strings.

SNMP Communities settings:

[1] 172.18.63.1 ronly Read/Write

Analysis: Both get and set requests from this NMS will be honoured when using the ronly community string. Any requests from NMS using rwrite, however, will be denied.

Case #4: NMS is listed in the SNMP Communities multiple times using the same community string.

SNMP Communities settings:

[1] 172.18.63.1 foobar Read

[2] 172.18.63.1 foobar Read/Write

Analysis: The NMS will only be allowed to use SNMP gets when using the community string foobar. This NMS can still use global community strings ronly for gets or rwrite for gets and sets as well.

Case #5: NMS is listed in the SNMP Communities under No Access.

SNMP Communities settings:

[1] 10.0.7.31 foobar Read

[2] 10.0.7.31 public No Access

Analysis: The NMS can perform only gets using the community string foobar. No other set or get requests will be honoured.

Case #6: NMS’s first listing is in the SNMP Communities under NoAccess

Community Read-Only: ronly

Community Read/Write: rwrite

[1] 10.0.7.31 foobar No Access

[2] 10.0.7.31 public Read/Write

Analysis: All NMS get or set requests are refused.

Toshiba MIB

The MIB is a set of objects that are processed via a network protocol. These objects determine what UPS parameters may be monitored and controlled using SNMP requests.

The RemotEye III communication implements standard MIB III and the following MIBs for TOSHIBA UPS:

1) Toshiba Enterprise RMTI-3 1600XP MIB File

2) Toshiba Enterprise RMTI-3 4200FA/4300 MIB File

3) Toshiba Japanese JEMA-Compliant MIB File

RemotEye III User Manual – 62330-005 101

Connecting to the RemotEye III via MODBUS

Executing SNMP Gets and Sets

Log into the RemotEye III using the HTTP interface. Verify the Modbus configuration as follows:

1. On the RemotEye III Main Screen, open RemotEye Management.

2. Click on Modbus TCP Configuration. The Modbus configuration window will open. See Fig. 50.

Figure 51: RemotEye III Modbus TCP Configuration

3. Verify the Modbus configuration is correct. The default settings are show in Figure 50. If unsure of the available options, click the HELP button.

4. Click on Set Values.

5. Click on Back to return to the Main screen.

6. RemotEye III is now ready for Modbus.

The Input Registers and Input Coils tables are listed in Appendix B.

Figure 52 Modbus Configuration HELP Screen

102 RemotEye III User Manual – 62330-005

Toshiba RemotEye Application Programs

Toshiba RemotEye Client Software

The Toshiba RemotEye Client Software runs on servers/PCs and connects to a designated RemotEye III. When the servers/PCs start up the RemotEye III scans for the UPS status. When UPS power events are detected, the RemotEye

III broadcasts a Shutdown command to the workstation. The Toshiba RemotEye Client Software will broadcast

warning messages (on the screen of the servers/PCs) and then shut down the server/PCs gracefully. See page 69, for

more details on the Shutdown Events configurations.

Install RemotEye III Client Shutdown software on VMware ESXi 5

See Appendix A for details of installing the Clinet Shutdown Software on VMware ESXi servers

.

Installation of RemotEye III Client using Windows 9x/2000/NT/XP/Vista/7/8 or

Windows Server 2003/2008/2012

Insert the RemotEye CD-ROM into the CD-ROM drive.

Run the Installer program (on the CD-ROM).

A configuration window box will be displayed on the screen, type in the IP address of the designated RemotEye, its

Client Name, and its Shutdown Delay Time. Click the Def. button to enter the workstation’s name as the Client Name

setting (see Figure 53: Toshiba RemotEye Client Software).

Upon completion of the setup screen’s entries, click OK and the RemotEye service will connect to the RemotEye automatically.

Figure 53: Toshiba RemotEye Client Software

RemotEye III User Manual – 62330-005 103

UPS Configuration

IP Address: Input RemotEye III IP address.

Local Configuration

This allows the administrator to set the client’s name and how it will handle a shutdown command sent by the

RemotEye III.

Client Name: Allows the administrator to enter the client’s name or to click the “Def.” button to capture the system’s “Computer Name”.

Shutdown Delay: Allows the administrator to type how many seconds till the actual client system shuts down if no script is being executed. NOTE: Make sure that the “UPS Output Shutdown Delay (secs)” under the “UPS

Management  UPS Shutdown Events” is longer than the seconds typed into this field. This will help avoid an unwanted system shutdown format.

Force Shutdown Delay: Allows the user to input another delay after the “Shutdown Delay” has expired. During this time delay the tool will execute the script that has been uploaded. When the “Force Shutdown Delay” expires it will force shutdown the client.

Script File: The administrator can upload their script file so that it can be executed after shutdown delay time is expired (e.g. close database).

Warn Speaker: Allows the administrator to enable the “beep” sound alarm whenever there is a warning.

Ignore Shutdown Request: Allows the administrator to cancel any shutdown command sent from RemotEye III.

Sleep: Allows the administrator to send the client system to hibernate instead of shutting down. (Administrator must first enable hibernation setting in the O.S.)

Enable POP Message: Allows the administrator to enable or disable the POP up warning messages.

Shutdown Events

This section allows the administrator to check the boxes on which conditions should the client system to be shutdown. When setting this make sure that these are also enabled in the RemotEye III “UPS Shutdown Events”

(UPS Management  UPS Shutdown Events, see page 69) section. These are the following conditions:

• AC Fail

• Battery Low

• UPS Overload

• UPS Over Temperature

• Weekly and Special Day Schedule shutdown

• EMD Temperature Over Threshold

• EMD Alarm-1

• EMD Alarm-2

Note: The client local shutdown delay must not be greater than the UPS shutdown delay configured in RemotEye

III.

104 RemotEye III User Manual – 62330-005

View the Connected Client via HTTP

Run the Web Browser on any machine.

Type in the RemotEye III’s IP address in the URL.

For example, type http://172.18.1.63

Select Connected Client Table from UPS Monitoring of the main menu and the list of the connected devices will be

shown on the screen Figure 54: HTTP Connected Client Table

Figure 54: HTTP Connected Client Table

Note: The client local shutdown delay must not be greater than the UPS shutdown delay configured in RemotEye III.

RemotEye III User Manual – 62330-005 105

Shutdown Process in Windows 9x/NT/2000/XP//Vista/7/8 & Server 2003/2008/2012

When RemotEye detects a power event, for example, AC power failure, the RemotEye will send the shutdown command to its connected clients. The clients will post a dialog box to notify the user that the system will be shutting down. Only checked events in the RemotEye III Client Configuration - Shutdown Events box will trigger a pop-up message and shutdown the Client. See the flow chart below for a graphical view of the interactions of the shutdown delays. Note: UPS Output Shutdown Delay not applicable to 4200FA/4300 UPS series.

Figure 55: Toshiba RemotEye Client Software

The user can select "Shutdown Now" to start the shutdown process or "Close" to minimize the shutdown window message. Toshiba RemotEye Client Software will proceed with the shutdown process and the host or server will be shutdown automatically if nothing is selected after the counter has counted down to zero.

106 RemotEye III User Manual – 62330-005

Figure 56: Toshiba RemotEye Client Software Shutdown Warning Message

There are five kinds of state for Toshiba RemotEye Client Software.

UPS Connection OK. (Green Background)

Trying to locate UPS. (Blue Background)

Local machine is about to shutdown. (Red Background)

The service is suspended. (Green Background)

Remote UPS is about to shut down or has shut down. (Grey Background)

NOTE: to cancel the shutdown process, right mouse click the red “battery” icon that is located in the bottom right side on the taskbar during the “local machine is about to shutdown” state and select the cancel shutdown option.

Uninstalling Toshiba Remoteye III Client Software

To uninstall the Toshiba RemotEye Client Software, the following procedure should be followed.

1.

2.

3.

Right mouse click the “battery” icon in the taskbar and select "Exit” to stop the shutdown service.

Select the "Add/Remove programs" icon from the Control Panel.

Select the "RemotEye", and then double click to remove the software.

RemotEye III User Manual – 62330-005 107

Installation of RemotEye Client using UNIX

Introduction

RSH is a software daemon which is able to get/set specific command from/into RemotEye. The major intention of this software is to shutdown the local machine before the UPS runs out of power. This program is composed by shell scripts, written in bash, and virtually portable under any UNIX operating system. The program consists of three phases: the installation phase, the execution phase, and the configuration phase.

• The installation phase will help the user setup the program properly by asking a few questions.

• The execution phase will keep track of the status of a UPS via RemotEye.

• The configuration phase will guide user to reconfigure the setting that is made in installation phase.

Program Overview

When installing this program, the shutdown shell application will check the target machine’s Operating System (OS) and determine whether it is a predefined OS from the recognized OS list. If it is not, the user will be prompted to answer some questions regarding system information (such as cmd name, path, etc). During the configuration phase, the program will ask user for information regarding the RemotEye (such as its IP address, name, etc). The reconfiguration phase allows the user to change the settings for later use. After installation, users can execute the program immediately or during the next system reboot.

Supported Operating System

1.

2.

3.

4.

Red Hat Advance Server release 2.1 AS

Sun Solaris 8 (x86)

Sun Solaris 8 (SPARC)

HP-UX (PA-RISC)

108 RemotEye III User Manual – 62330-005

Installation

During the installation phase, the following steps are taken to help users install this program:

The program will automatically detect the target machine’s OS and OS’s distribution. User needs to select the correct item by entering the item number:

1. Please choose your OS:

2. Please choose your OS_Name:

If the target system is NOT on the predefined OS-list, the user will be prompted the following questions (questions

3~8)

3. “/dev” is your system device directory: [y/n] o If “n” is selected,

4. Input device directory: o

Using “rsh” for remote shell:[y/n] o

If “n” is selected,

5.

6.

7.

8.

Input remote shell: o

Using “/sbin/init0” to shut down your system:[y/n] o

If “n” is selected,

Input shut down command: o

Please input your system’s initial directory at boot time: o

Please input run level’s directory to boot into: o

Do you have other run levels that need input?[y/n] o

If “n” is selected,

Please input run level directory: o

Install to folder /etc[y/n] o

If “n” is selected,

Input install folder: o

Do you want to start the daemon now?[y/n]

RemotEye III User Manual – 62330-005 109

Execution

After successful installation of the program, users can use the uGuard.sh script to perform the following action.

Usage: ./uGuard.sh -[h][v][s][S][u][U][d][l][e][g] where h: This manual page. v: Show revision information. s: Start the program now.

S: Start the program at next boot up time. u: Unload program.

U: Unload program, don’t restart at next boot time. d: Suspend program. l: List configurations. e: Modify configurations. g: See log [/var/log/usha/ug_usha.log].

Configuration

In this phase, users are able to change the parameters for the program. Users can change the setting to fit their needs at any time by executing “uGuard.sh –e”. After the first configuration process, this phase will show the last setting value as a default setting.

Input USHA IP Address:

Input Client Name:

Warning Beep On? [y/n]

Shutdown delay time is 120 seconds?[y/n]

If “n” is selected,

Input shut down delay time:

Shut down script is loaded?[y/n]

If “n” is selected,

Input shut down script:

Force shut down delay time is 120 seconds?[y/n]

If “n” is selected,

Input force shut down delay time:

Shut Down Enable?[y/n]

110 RemotEye III User Manual – 62330-005

Toshiba UPS Power Management

RemotEye III can help further protect critical load systems connected to a UPS by initiating automated shutdowns on that equipment. RemotEye III can shutdown servers/clients upon detection of three UPS events: Input power failure, low battery, overload. Also, RemotEye III can be used to coordinate automatic system shutdowns during weekends or holidays. This section highlights the manners in which RemotEye III can be used in conjunction with a UPS to manage power to UPS loads.

UPS Shutdown Events

RemotEye III can initiate output shutdown upon the occurrence of nine different UPS events Input Power Failure,

Low Battery, UPS Overload, UPS System Overheat, EMD Temperature Over Threshold, EMD Alarm-1, EMD

Alarm-2, Recurring On/Off Schedule and Non-recurring On/Off Schedule. Users can view the current setting of

these events on

UPS Shutdown Events page in UPS Management menu. To alter these settings, log in as an administrator, and

configure the UPS shutdown events action and delay times accordingly. Click the Set Value button when finished.

(See Pg. 69 for details)

Scenario:

Shutdown Event:

Status:

Delay (Min):

Warning Interval (sec):

UPS Output Shutdown Delay (Sec):

UPS Events - AC failed

22 : 20 : 00 22 : 27 : 00 22 : 30 : 00

AC Failed

Client Shutdown

7 (default)

30 (default)

180 (default)

22:20:00

INVERTER

OUTPUT

SHUTDOWN

Client’s local shutdown delay (Sec):

22 : 20 : 00 22 : 27 : 00 22 : 29 : 00

CLIENT ON

CLIENT OFF

120(default)

RemotEye III User Manual – 62330-005 111

Managing the UPS Recurring & Non-recurring Schedule (Applicable to 1600XP Only)

RemotEye III supports two output shutdown schedule – (1) Recurring Schedule; (2) Non-recurring Schedule.

Note: Before managing the UPS Shutdown Schedule, please make sure that the Date and Time configured in

RemotEye III is correct.

Scenario

Shutdown Event:

Status:

Delay (Min):

Recurring Schedule

UPS Output shutdown

10(default)

Warning Interval (sec):

UPS Shutdown Delay (Sec):

Shutdown & Restart day & time:

Shutdown & Restart day & time:

60(default)

180(default)

Monday 22:20:00 ----- 99:99:99

Tuesday 99:99:99 ----- 09:00:00

Note: 99:99:99 indicates the RemotEye III will ignore the Restart Time on Monday, and the Shutdown time on

Tuesday.

Monday

Tuesday

22 : 20 : 00 22 : 30 : 00 22 : 33 : 00 09:00:00

INVERTER

OUTPUT

SHUTDOWN

112 RemotEye III User Manual – 62330-005

Auto Save-Log Software

Save-Log is utility software which is able to save logs from one or more RemotEyes at the same time. It also has the capability to save logs periodically. These logs are useful in identifying problems with the UPS. There are different

types of logs, each with their own functionality. Information on these types of logs is found in pages 83.

The Auto Save log software will automatically save the RemotEye list and settings. This eliminates having to reenter the information again after the program is closed or when the workstation running the software is shutdown.

Installation of Save-Log

1. The software for the Auto Save log is loaded on the CD included in the RemotEye package. It also be downloaded from the Toshiba website at www.toshiba.com/ind and clicking on the following path:

RemotEye III Download RemotEye Files Save Log.

2.

3.

Download the software from the CD or the internet and run the program Savelog_install.exe and follow the setup installation instructions.

After installation has finished click on the icon, TOSHIBA_AutoSaveLog under the All Programs start menu in order to execute.

Basic Layout

When opening the Save Log utility software, it will display a window like the one shown below. This window displays a top row of tabs listing the UPS product lines and an Overview tab.

Toolbar ID

4

5

6

1

2

3

Item Name

Save Log Setting

Browse

Add

Delete

Edit

Discover

Description

The saving history log settings

Using default browser to open homepage of selected device

Pop-up Add dialog to add one device

Delete selected device which one or more

Pop-up Edit dialog to input correct account and password

Discover all devices on the network

Figure 57: Save Log Utility RemotEye – Auto Save Log Tab

RemotEye III User Manual – 62330-005 113

Selecting

Unit must be selected then Save Log Settings, Acquire, Browse, Delete, Edit and Open File become available.

Figure 58: RemotEye Save Log Utility - RemotEye – Selecting

Device List

Display the number of devices in the list.

114

Figure 59: RemotEye Save Log Utility – Device List

RemotEye III User Manual – 62330-005

Status

Green color indicates good connection and red color indicates disconnect.

Figure 60: RemotEye Save Log Utility – Status

Save Log Setting

When the unit has been selected and clicked Save Log Settings button becomes available.

Figure 61: RemotEye Save Log Utility – Settings

Once the Save Log Setting is clicked, the save items will appear. The history logs displayed depends on UPS model selected.

RemotEye III User Manual – 62330-005 115

Figure 62: RemotEye Save Log Utility – Set Page

116 RemotEye III User Manual – 62330-005

Tupgrade Firmware Tool

General information

To perform a firmware upgrade, the RemotEye III must be connected to the same network as the workstation from which the upgrade file is to be sent. In the RemotEye III make sure the Network Upgrade Control is enabled, under

RemotEye III Control, and that users have the Admin login and Password string information.

Here is the way to manually upgrade RemotEye Firmware:

1) Web Interface: Go to RemotEye III Management RemotEye III Control menu then Enable Network

Upgrade Control.

Note: To enable the Network Upgrade user has to change the security level to administrator by logging in

as Administrator.

2) Open the Tupgrade application software and click on the Discover icon. If no RemotEye units auto populate the list, press on the + icon and enter the IP, Username, and Password. If it still does not appear check your network security and your computer firewall.

3) Select the check box right next to the RemotEye that will be updated.

4) Select the Edit button and enter the Username and Password.

5) Select the Open File button and select the firmware to be uploaded.

6) Select the Upgrade Firmware button to start the upgrade process.

Figure 63: Tupgrade Utility – Opening Display

Table 4: Tupgrade Toolbar Functions

Toolbar ID Icon Name

1 Set IP

2

3

Acquire

Browse

4

5

6

7

8

9

Add

Delete

Edit

Discover

Open file

Description/Function

Manually set found device IP address, subnet mask and gateway

Get all device parameters. This generates a config file.

Use default browser to open homepage of selected device

Pop-up Add dialog to add one device

Delete one or more selected devices.

Pop-up Edit dialog to modify a device configuration.

Discover all RemotEye devices on the network.

Open the location (directory) of uploaded file.

Upgrade Firmware Upgrade firmware after unit selected and file uploaded

RemotEye III User Manual – 62330-005 117

Used in conjunction with the RemoteConfig Tool, the Tupgrade Tool can push/save a RemotEye Config file to one or more selected RemotEyes simultaneously, making for a quick system setup.

To save RemotEye III Config file:

1) Discover or Manually add the RemotEye III to the list.

2) Select the check box of the RemotEye III to acquire config file.

3) Press the Edit button and enter administrator login credentials.

4) Press the Acquire button and select the config file destination.

Load Config file to RemotEye III:

1) Discover or Manually add the RemotEye III to the list.

2) Select the check box of the RemotEye III to load the config file.

3) Press the Edit button and enter administrator login credentials.

4) Press the Open file button and select the config file to be uploaded.

5) Press the Upgrade Firmware button to upload the selected config file.

Upgrading RemotEye III Firmware from UNIX

The RemotEye III firmware may be upgraded from a Unix platform by performing the procedure below. To upgrade the firmware using a UNIX operating system, the tftp command must be installed on the system.

To upload the new firmware to the RemotEye III, execute the following command line:

# tftp tftp> binary tftp> connect <host> tftp> put <filename> upgrade@<password>@<username> where:

binary

<host>

: Binary data download mode.

: RemotEye III IP address.

Example: 172.168.1.18. put : PUT command.

<filename> : Name of the file containing the firmware image.

Example: \TSB100.bin. upgrade : Upgrade key word.

@ : Character separator.

<password> : Community Read/Write string.

<username> : HTTP login user name.

118 RemotEye III User Manual – 62330-005

RemotEye III Specifications

RemotEye III Feature Summary

CPU

Memory

Network

Serial Communication

Serial Connection

Jumper

DIP Switch

LED

Reset Button

RTC

16-Bits AC1106 Fast Ethernet RISC Processor

2MB(1Mbit x16) TFBGA Flash ROM

2MB (1Mbit x16) SDRAM

Support 10/100 Mbits

RJ45 LAN Connector

Two UART Channels, one RJ-45, one Gold finger.

Console - RJ45 Connecter (FULL Function /RS-232 Level)

UPS - Gold finger (TXD, RXD/RS-232 Level)

Two bits for upgrade mode configure.

Two bits for operating mode configure.

Power x1 (Green)

Status x1 (Yellow)

LAN 10 Link/Activity x 1 (Yellow)

LAN 100 Link/Activity x 1 (Green)

One Push Button

Real time clock

RemotEye III User Manual – 62330-005 119

System Specifications

Description

Power Input

Power Consumption

Temperature Operating

Temperature Non-operating

Humidity Operating

Humidity Non-operating

Board dimension

Weight

Regulation

Specification

+8V ~ +15VDC

3.0 Watts Maximum

+8V DC 1.56 Watts

+15V DC 1.7 Watts

0

∘C ~ +60∘C

-10

∘C ~ +70∘C

10 ~ 80 %

5 ~ 95 %

65.8x 60 x 15.2 mm (LxWxH)

45 gm

CE,FCC class B

Firmware Specifications

Network Protocols

SNMP

UPS Protocol

SNMP over UDP/IP, HTTP over TCP/IP

ARP, RARP , DHCP, DNS, BOOTP, SMTP, SNTP, TFTP,

SSL, SSH, PPP, ICMP, RADIUS

RFC 1628, JEMA MIB, TOSHIBA MIB

TOSHIBA UPS protocol

120 RemotEye III User Manual – 62330-005

LED Key

Front

Figure 64: RemotEye III/Internal Top View

4 3 2 1

Figure 65: Front View – LED location

(1) Status LED (Yellow)

J2

(2) Power LED (Green)

(3) LAN 10 Link/Activity LED (Yellow)

Table 3. LED define list

RemotEye III User Manual – 62330-005 121

Jumper Setting

2

1

4

3

J4 Jumper

Pin1/2 Pin3/4 Function

1

1

0

1

0

1

Reserved

Clear Password

Reserved

0 0

1: Jumper short ; 0 : Jumper open

Reserved

Table 4. J4 Jumper Setting Table

※ Example: Setup Serial Upgrade Z-modem Mode (S1 DIP Switch must Setup: S1-1 on, S1-2 off)

Pin1/2: Jumper open.

Pin3/4: Jumper short.

122

2

1

4

3

RemotEye III User Manual – 62330-005

DIP Switch Setting

1 2

O

N

S1-1(PIN1/4) S1-2(PIN2/3) Function

ON ON Manufacturing Diagnostic Mode

OFF

ON

OFF

ON

OFF

OFF

Debug Mode

Serial Upgrade Mode

Operational Mode (Default)

Table 5. S1 DIP Switch Setting Table

LAN connector (J2)

Pin

3

4

5

1

2

6

7

8

Signals

TX+ / TDP

TX- / TDN

RX+ / RDP

NC

NC

RX- / RXN

NC

NC

Function

OUTPUT +

OUTPUT -

INPUT +

NO CONNECT

NO CONNECT

INPUT -

NO CONNECT

NO CONNECT

Table 6. RJ45 LAN connector pin descriptions

Console connector (J3)

RemotEye III User Manual – 62330-005 123

Pin

4

5

6

7

8

1

2

3

Signals

RTSPC#

DTRPC#

TXDPC#

COM

DCDPC#

RXDPC#

DSRPC#

CTSPC#

Function

Request To Send – RS232 level

Data Terminal Ready – RS232 level

Serial Data Out (to PC) – RS232 level

GND

Data Carrier Detector – RS232 level

Serial Data In (from PC) – RS232 level

Data Set Ready – RS232 level

Clear To Send– RS232 level

Table 7. RJ45 Console connector pin descriptions

Gold Finger GF1

PIN Num.

7

8

5

6

3

4

1

2

9

10

Signals

NC

NC

NC

D+

GND

UPSVCC

TXDUPS(to UPS) – RS-232 level

RXDUPS(from UPS) – RS-232 level

GND

D-

Table 8. Gold finger GF1 pin descriptions

Note

8~15Vdc

Detect+

Detect-

124 RemotEye III User Manual – 62330-005

Appendix A: Install RemotEye Client Shutdown Software on

VMware ESXi 5

The following steps detail how to install and configure the Remote Shutdown Client software to work with ESXi

servers. Figure 0-1 shows an array of ESXi servers hosting a variety of Guest OS which are shut down gracefully by

the vMA Guest which is controlled by the RemotEye.

Software Needed

Toshiba Provided:

• RemotEye II Firmware v4.10 or higher.

• RemotEye III Firmware v1.05 or higher

• RemotEye ESXi Client Shutdown Daemon (TAR file)

Customer Provided:

• ESXi 5 OS (Operating System) – Full or Evaluation Version (not the Free version)

• VMware vSphere Client for Windows (Allows Windows access to ESXi)

• vSphere Management Assistant (vMA) Operating System

• WinSCP

• Basic knowledge of UNIX/Linux commands

RemotEye Shutdown Commands

RemotEye

II/III

VMA

Guest OS1

Virtual

Guest OS2

Virtual

Guest OS3

Toshiba

UPS 1

VMware ESXi Server 3

Virtual

Guest OS1

Virtual

Guest OS2

Virtual

Guest OS3

Toshiba

UPS 2

RemotEye

II/III

VMware ESXi Server 3

Virtual

Guest OS1

Virtual

Guest OS2

Virtual

Guest OS3

VMware ESXi Server 3

Figure 0-1 Network with RemotEye and ESXi Servers

RemotEye III User Manual – 62330-005 125

Setup Procedure for RemotEye ESXi Client Shutdown Daemon*

* Daemon – A program on Unix/Linux-like operating systems that runs unobtrusively in the background, waiting to be activated by the

occurrence of a specific event or condition.

1. Confirm that ESXi is a Full or Evaluation version. (The Free version does not support this function.)

2. If vMA is already installed in ESXi skip to Step 7. Otherwise, download vMA OS (SUSE OS) from the

Downloads section of the VMware website, www.vmware.com

.

3. Install vMA OS (SUSE OS) on ESXi server by navigating to File > Deploy OVF Template and follow the instructions.

4. Run vMA OS.

Note: Default username is vi-admin. When prompted for the password, just press the Enter key.

5. Change the vMA settings. Ensure RemotEye has access to the vMA network. (Example: Assign the IP to

10.2.0.11)

6. Create the Super User password:

6.1. Type “sudo passwd” into the command line prompt and press Enter. Follow the instructions to create the root password.

6.2.

Type “su root” into command prompt and press Enter. Follow the instructions to log in as root. Note:

When logged in as Super User, text color turns

RED

. (See Figure 0-2)

Figure 0-2 Text turns RED in Super User Mode

7. Add the server to vMA using “vfip addserver [ESXi Server IP]”, then enter the ESXi password. (Example:

IP=10.1.10.220) (See Figure 0-3)

Figure 0-3 Add Server to vMA

8. Confirm ESXi was added to vMA: On the command line type “vifp listservers and press Enter. The

command returns: 10.1.10.220 ESXi (See Figure 0-4)

Figure 0-4 ESXi Added to VMA

9. Enable SSH in vMA (if not Enabled).

9.1. On the command line prompt type: “vi /etc/hosts.allow” and press Enter.

9.2. Type “l” and press Enter. (edits file)

9.3. Type “sshd: ALL: ALLOW” and press Enter.

9.4. Press the ESC key.

126 RemotEye III User Manual – 62330-005

9.5. Type “w” and press Enter. (writes to file)

9.6. Type “q” and press Enter. (exits file)

10. Connect to vMA using WinSCP software to transfer the RemotEye Client shutdown software.

Open WinSCP and select either SFTP or SCP for the file protocol, and enter the vMA IP address/Host

Name, User name, and Password. (Example: Host Name - 10.2.0.11.) Then click the Login button.

(See Figure 0-5)

Figure 0-5 WinSCP Login Screen

10.1. Locate SD_ESXi_TSB_V100.tar file (left side), then select the directory where you want it stored on the

vMA (right side) and press the F5 key. (See Figure 0-6)

RemotEye III User Manual – 62330-005 127

Figure 0-6 WinSCP vi-admin Screen

10.2. Close WinSCP program.

11. Return to the vMA command prompt and change the directory where the SD_ESXi_TSB_V100.tar was placed in step 10.

12. Extract the software: Type “tar xvf SD_ESCi_V100.tar” in the command prompt and press Enter.

13. Go to the newly created folder SD_ESXi_TSB: Type “cd SD_ESXi_TSB” and press Enter.

14. Install the software: Type “sh install.sh” in the command prompt and press Enter. Follow the instruction

prompts. (See Figure 0-7)

128 RemotEye III User Manual – 62330-005

Figure 0-7 Install Screen Shot

15. Verify that RemotEye and ESXi server are communicating. Go to RemotEye web interface and look for

the "Connected Client Table" web page. Open the Connected Client Table web page. (See Figure

0-8)

Figure 0-8 Connected Client Table in RemotEye III

16. Go back to VMware vSphere Client program and select the ESXi server IP address -> Configuration ->

Virtual Machine Startup/Shutdown -> Properties… to set up Client OSs (guests) to shut down before the

vSphere Management Assistant (vMA) as shown in Figure 0-9.

Make sure that the check box for Allow virtual machines to start and stop automatically with the system is

checked and the Shutdown Action is set to Guest Shutdown. (See Figure 0-9)

RemotEye III User Manual – 62330-005 129

1

2

4

3

Figure 0-9 vSphere Management Asistant Screen Shot

17. Install WMware Tools for the client OSs by going to Inventory -> Virtual Machine -> Guest ->

Install/Upgrade VMware Tools.

NOTE: If VMware Tools are not installed, the graceful system shutdown will not be carried out properly.

18. Enter UPS Shutdown Events in RemotEye. This designates those UPS Events whose occurrence trigger the

RemotEye to send the shutdown command to the ESXi server.

18.1. Open RemotEye II/III and click on UPS Agent > UPS Management > UPS Shutdown.

18.1.1. In the UPS Shutdown Events table, select the action (Disable, Client Warning, or Client

Shutdown) and Shutdown Delay (if applicable), for each event listed in the UPS Event column. (See

and Error! Reference source not found. and Figure 0-10)

18.1.2. Click the Set Values button when completed.

130 RemotEye III User Manual – 62330-005

Figure 0-10 RemotEye III UPS Shutdown Events Table

19. Test it. (See Figure 0-11)

NOTE: Testing the SHUT DOWN function will shut down all affected servers.

Figure 0-11 RemotEye III Main Display with Shutdown Test Buttons

RemotEye III User Manual – 62330-005 131

30006

30007

30008

30009

30010

30011

30012

30013

30014

30015

30016

30017

30018

30019

30020

30021

Appendix B – Modbus Registers

Modbus Input Register for 1600XP: MONITORING

NOTE: Items Lined out (e.g. Lined Out) are not supported at this time.

Registers Data Type Size Description

30001 Unsigned Integer 16-Bit RemotEye III Software Version

30002

30003

30004

30005

Unsigned Integer 16-Bit RemotEye III Slave ID Number

Unsigned Integer 16-Bit IP Address First Byte

Unsigned Integer 16-Bit IP Address Second Byte

Unsigned Integer

16-Bit

Read

Only

IP Address Third Byte

Unsigned Integer 16-Bit IP Address Fourth Byte

Unsigned Integer 16-Bit Subnet Mask First Byte

Unsigned Integer 16-Bit Subnet Mask Second Byte

Unsigned Integer 16-Bit Subnet Mask Third Byte

Unsigned Integer 16-Bit Subnet Mask Fourth Byte

Unsigned Integer 16-Bit Gateway IP Address First Byte

Unsigned Integer 16-Bit Gateway IP Address Second Byte

Unsigned Integer 16-Bit Gateway IP Address Third Byte

Unsigned Integer 16-Bit Gateway IP Address Fourth Byte

Unsigned Integer 16-Bit RemotEye III Installation Date

Unsigned Integer 16-Bit RemotEye III Installation Date

Unsigned Integer 16-Bit RemotEye III Installation Date

Unsigned Integer 16-Bit Date on RemotEye III

Unsigned Integer 16-Bit Date on RemotEye III

Unsigned Integer 16-Bit Date on RemotEye III

Unsigned Integer 16-Bit Time on RemotEye III

Units

Firmware

ID

IP Address

IP Address

IP Address

IP Address

Subnet Mask

Subnet Mask

Subnet Mask

Subnet Mask

IP Address

IP Address

IP Address

IP Address

Month

Day

Year

Month

Day

Year

Hour

Multiplier Comments

X 0.01

X 1

X 1

X 1

Example: Value received is 103

Example: "192" from 192.168.1.150

Example: "168" from 192.168.1.150

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

Example: "1" from 192.168.1.150

Example: "150" from 192.168.1.150

Example: "255" from 255.255.255.0

Example: "255" from 255.255.255.0

Example: "255" from 255.255.255.0

Example: "0" from 255.255.255.0

Example: "192" from 192.168.1.1

Example: "168" from 192.168.1.1

Example: "1" from 192.168.1.1

Example: "1" from 192.168.1.1

Month Format: MM

Day Format: DD

Year Format: YYYY

Month Format: MM

Day Format: DD

Year Format: YYYY

Hour Format: HH

132 RemotEye III User Manual – 62330-005

Registers

30022

30023

30024

30025

30026

30027

Data Type Size Description

Unsigned Integer 16-Bit Time on RemotEye III

Unsigned Integer 16-Bit Time on RemotEye III

ASCII String

ASCII String

16-Bit

16-Bit

Manufacture (first two characters)

Manufacture (third and fourth characters)

ASCII String 16-Bit

Manufacture (fifth and sixth characters)

ASCII String 16-Bit Manufacture (seventh character)

30028

30029

30030

30031

30032

30033

30034

30035

30036

30037

30038

30039

30040

ASCII String

ASCII String

ASCII String

ASCII String

ASCII String

ASCII String

ASCII String

ASCII String

ASCII String

ASCII String

ASCII String

ASCII String

ASCII String

Units

Minute

Seconds

Characters

Characters

Characters

Characters

16-Bit UPS Typeform (first two characters) Characters

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

UPS Typeform (third and fourth characters)

UPS Typeform (fifth and sixth characters)

UPS Typeform (seventh and eighth characters)

UPS Typeform (ninth and tenth characters)

UPS Typeform (eleventh and twelve characters)

UPS Typeform (thirteen and fourteen characters)*

UPS Typeform (fifteen and sixteen characters)*

UPS Serial Number (first two characters)

UPS Serial Number (third and fourth characters)

UPS Serial Number (fifth and sixth characters)

UPS Serial Number (seventh and eighth characters)

UPS Serial Number (ninth and tenth characters)

Characters

Characters

Characters

Characters

Characters

Characters

Characters

Characters

Characters

Characters

Characters

Characters

None

None

None

None

None

None

None

None

None

None

None

None

None

None

None

Multiplier Comments

X 1 Minute Format: MM

X 1

None

Seconds Format: SS

Constant: "To" from To shiba

None Constant: "sh" from To sh iba

Constant: "ib" from Tosh ib a

Constant: "a" from Toshib a

UPS Typeform Example:

UH 3G2L036C61TPA3

UPS Typeform Example:

UH 3G 2L036C61TPA3

UPS Typeform Example:

UH3G 2L 036C61TPA3

UPS Typeform Example:

UH3G2L 03 6C61TPA3

UPS Typeform Example:

UH3G2L03 6C 61TPA3

UPS Typeform Example:

UH3G2L036C 61 TPA3

UPS Typeform Example:

UH3G2L036C61 TP A3

UPS Typeform Example:

UH3G2L036C61TP A3

Serial # Example: 20 12101234567891

Serial # Example: 20 12 101234567891

Serial # Example: 2012 10 1234567891

Serial # Example: 201210 12 34567891

Serial # Example: 20121012 34 567891

RemotEye III User Manual – 62330-005 133

30044

30045

30046

30047

30048

30049

30050

30051

30052

30053

30054

30055

30056

30057

30058

30059

30060

30061

30062

30063

30064

30065

30066

Registers

30041

30042

30043

Data Type Size Description

ASCII String

ASCII String

ASCII String

16-Bit

16-Bit

16-Bit

UPS Serial Number (eleventh and twelve characters)

UPS Serial Number (thirteen and fourteen characters)

UPS Serial Number (fifteen and sixteen characters)

Unsigned Integer 16-Bit UPS Capacity

Unsigned Integer 16-Bit UPS Installation Date

Unsigned Integer 16-Bit UPS Installation Date

Unsigned Integer 16-Bit UPS Installation Date

Unsigned Integer 16-Bit UPS Hardware Build Date

Unsigned Integer 16-Bit UPS Hardware Build Date

Unsigned Integer 16-Bit UPS Hardware Build Date

Unsigned Integer 16-Bit UPS Test Date

Unsigned Integer 16-Bit UPS Test Date

Unsigned Integer 16-Bit UPS Test Date

Unsigned Integer 16-Bit UPS System Temperature

Unsigned Integer 16-Bit UPS System Temperature

Unsigned Integer 16-Bit UPS Battery Temperature

Unsigned Integer 16-Bit UPS Battery Temperature

Unsigned Integer 16-Bit Input Numbers of Phases

Unsigned Integer 16-Bit Input Voltage

N/A N/A N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

Unsigned Integer 16-Bit Input Voltage Percent

N/A N/A N/A

Units

Characters

Characters

Characters kVA

Month

Day

Year

Month

°C

°F

°C

°F

Day

Year

Month

Day

Year

Phase

Volts

N/A

N/A

N/A

N/A

N/A

%

N/A

Multiplier Comments

None Serial # Example: 2012101234 56 7891

None

None

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

N/A

N/A

N/A

N/A

N/A

X 1

N/A

Serial # Example: 201210123456 78 91

Serial # Example: 20121012345678 91

Month Format: MM

Day Format: DD

Year Format: YYYY

Month Format: MM

Day Format: DD

Year Format: YYYY

Month Format: MM

Day Format: DD

Year Format: YYYY

RemotEye Converts °C to °F

RemotEye Converts °C to °F

134 RemotEye III User Manual – 62330-005

30084

30085

30086

30087

30088

30089

30090

30091

30092

30093

30075

30076

30077

30078

30079

30080

30081

30082

30083

Registers

30067

30068

30069

30070

30071

30072

30073

30074

Data Type

N/A

Size Description

N/A N/A

Unsigned Integer 16-Bit Input Rated Voltage (V)

N/A N/A N/A

Unsigned Integer 16-Bit Input Current

Unsigned Integer 16-Bit Input Current Percent

Unsigned Integer 16-Bit Input Rated Current

Unsigned Integer 16-Bit Input Frequency

N/A N/A N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A N/A N/A

Unsigned Integer 16-Bit Input Rated Frequency

Unsigned Integer 16-Bit Input Active Power (Part 1 of 2)

Unsigned Integer 16-Bit Input Active Power (Part 2 of 2)

Unsigned Integer 16-Bit Input Rated Active Power

Unsigned Integer 16-Bit Input Apparent Power (Part 1 of 2)

Unsigned Integer 16-Bit Input Apparent Power (Part 2 of 2)

N/A N/A N/A

Unsigned Integer 16-Bit Input Power Factor

Unsigned Integer 16-Bit Output Number of Phases

Unsigned Integer 16-Bit Output Voltage

N/A N/A N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

PF

Phase

Volts

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

Hz

Watts

Watts

KWatts

VA

VA

Units

N/A

Volts

N/A

Amps

%

Amps

Hz

N/A

N/A

X 1

X 1

X 1

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

X 0.1

X 1

X 1

X 1

X 1

X 1

Multiplier Comments

N/A

X 1

N/A

X 1

X 1

X 0.1

X 0.1

N/A

Use this formula: (Register (30079) *

0x10000) + Register (30080)

Use this formula: (Register (30082) *

0x10000) + Register (30083)

RemotEye III User Manual – 62330-005 135

30111

30112

30113

30114

30115

30116

30117

30118

30119

30120

30102

30103

30104

30105

30106

30107

30108

30109

30110

Registers

30094

30095

30096

30097

30098

30099

30100

30101

Data Type

N/A

Size Description

N/A N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A N/A N/A

Unsigned Integer 16-Bit Output Under Voltage Level

Unsigned Integer 16-Bit Output Over Voltage Level

Unsigned Integer 16-Bit Output Rated Voltage

Unsigned Integer 16-Bit Output Current

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A N/A N/A

Unsigned Integer 16-Bit Output Load Percentage

Unsigned Integer 16-Bit Output Rated Current

Unsigned Integer 16-Bit Output Frequency

N/A N/A N/A

N/A N/A N/A

Unsigned Integer 16-Bit Output Frequency Synch Range

Unsigned Integer 16-Bit Output Rated Frequency

Unsigned Integer 16-Bit Output Active Power (Part 1 of 2)

Unsigned Integer 16-Bit Output Active Power (Part 2 of 2)

N/A N/A N/A

Unsigned Integer 16-Bit Output Rated Active Power

Amps

Hz

N/A

N/A

Hz

Hz

Watts

Watts

N/A

KWatts

Volts

Amps

N/A

N/A

N/A

N/A

N/A

N/A

%

Units

N/A

N/A

N/A

N/A

N/A

N/A

%

%

X 0.1

X 0.1

N/A

N/A

X 0.1

X 0.1

X 1

X 1

N/A

X 1

X 1

X 0.1

N/A

N/A

N/A

N/A

N/A

N/A

X 1

Multiplier Comments

N/A

N/A

N/A

N/A

N/A

N/A

X 1

X1

Use this formula: (Register (30117) *

0x10000) + Register (30118)

136 RemotEye III User Manual – 62330-005

Registers

30121

Data Type Size Description Units

Unsigned Integer 16-Bit Output Apparent Power (Part 1 of 2) VA

30122

30123

30124

30125

30126

30127

30128

30129

30130

30131

30132

30133

30134

30135

30136

30137

30138

30139

30140

30141

30142

30143

30144

30145

Unsigned Integer 16-Bit Output Apparent Power (Part 2 of 2) VA

Unsigned Integer 16-Bit Output Rated Apparent Power

N/A N/A N/A

Unsigned Integer 16-Bit Output Rated Power Factor

Unsigned Integer 16-Bit Bypass Number of Phases

Unsigned Integer 16-Bit Bypass Voltage

N/A N/A N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

Unsigned Integer 16-Bit Bypass Under Voltage Detection

N/A N/A N/A

Unsigned Integer 16-Bit Bypass Under Voltage Recovery

Unsigned Integer 16-Bit Bypass Over Voltage Detection

Unsigned Integer 16-Bit Bypass Over Voltage Recovery

%

Volts

Volts

Unsigned Integer 16-Bit Bypass Current

Unsigned Integer 16-Bit Bypass Frequency

N/A

N/A

N/A

N/A

N/A

N/A

Amps

Hz

N/A

N/A

Unsigned Integer 16-Bit Bypass Apparent Power (Part 1 of 2) VA

N/A

N/A

N/A

N/A

N/A

N/A

N/A

%

N/A

KVA

N/A

PF

Phase

Volts

N/A

Multiplier Comments

X 1

Use this formula: (Register (30121) *

0x10000) + Register (30122)

X 1

N/A

N/A

N/A

N/A

N/A

N/A

N/A

X 1

N/A

X 1

N/A

X 1

X 1

X 1

N/A

X 1

X 1

X 1

X 0.1

X 0.1

N/A

N/A

X 1 Use this formula: (Register (30145) *

RemotEye III User Manual – 62330-005 137

30163

30164

30165

30166

30167

30168

30169

30170

30171

30172

30154

30155

30156

30157

30158

30159

30160

30161

30162

Registers

30146

30147

30148

30149

30150

30151

30152

30153

Data Type Size Description Units

Unsigned Integer 16-Bit Bypass Apparent Power (Part 2 of 2) VA

Unsigned Integer 16-Bit DC Bus Total Voltage

Unsigned Integer 16-Bit DC Bus Positive Voltage

Unsigned Integer 16-Bit DC Bus Negative Voltage

Unsigned Integer 16-Bit DC Bus Rated Voltage

Unsigned Integer 16-Bit Battery Installation Date

Unsigned Integer 16-Bit Battery Installation Date

Unsigned Integer 16-Bit Battery Installation Date

Volts

Volts

Volts

Volts

Month

Day

Year

Unsigned Integer 16-Bit Estimated Battery Runtime

Unsigned Integer 16-Bit Number of Discharges

Unsigned Integer 16-Bit Elapsed Time on Battery Power

Unsigned Integer 16-Bit Estimated Battery Life Remaining

Unsigned Integer 16-Bit Battery Voltage

Minutes

Times

Seconds

Months

Vdc

Unsigned Integer 16-Bit Battery Capacity

Unsigned Integer 16-Bit Battery Discharge Current

%

Adc

Unsigned Integer 16-Bit Battery Charge Over Voltage Delay Seconds

N/A N/A N/A N/A

N/A

N/A

N/A

N/A

N/A

N/A

Unsigned Integer 16-Bit Rated Low Battery Voltage

Unsigned Integer 16-Bit Rated Low Battery Level

Unsigned Integer 16-Bit Rated Battery Shutdown Voltage

Unsigned Integer 16-Bit Rated Voltage Shutdown Level

Unsigned Integer 16-Bit Rated Battery Ampere Hour

Unsigned Integer 16-Bit Batteries in Series

Unsigned Integer 16-Bit Batteries in Parallel (Strings)

Unsigned Integer 16-Bit External Battery Installation Date

N/A

N/A

Vdc

%

Vdc

%

Ahr

Batteries

Strings

Month

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 0.1

X 1

N/A

N/A

N/A

X 1

Multiplier Comments

X 1

0x10000) + Register (30146)

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

Month Format: MM

Day Format: DD

Year Format: YYYY

Month Format: MM

138 RemotEye III User Manual – 62330-005

Registers

30173

30174

30175

Data Type

Unsigned Integer

Unsigned Integer

Size

16-Bit

16-Bit

Description

External Battery Installation Date

External Battery Installation Date

Units

Day

Year

Unsigned Integer 16-Bit External Battery Rated Ampere Hour Ahr

30176

30177

30178

Unsigned Integer 16-Bit External Battery C Rate

Unsigned Integer 16-Bit External Batteries in Series

Unsigned Integer 16-Bit

External Batteries in Parallel

(Strings)

C

Batteries

Batteries

30179 ASCII String 16-Bit

Battery Cabinet 1 Serial Number

UH 23XXX1

Serial #

30180

30181

30182

30183

30184

30185

30186

30187

30188

ASCII String 16-Bit

Battery Cabinet 1 Serial Number

UH 23 XXX1

Serial #

ASCII String

ASCII String

16-Bit

16-Bit

Battery Cabinet 1 Serial Number

UH23 XX X1

Battery Cabinet 1 Serial Number

UH23XX X1

ASCII String

ASCII String

16-Bit

16-Bit

Battery Cabinet 1 Firmware Version ex.

00 0015

Battery Cabinet 1 Firmware Version ex. 00 00 15

ASCII String

Signed Integer

16-Bit

16-Bit

Battery Cabinet 1 Firmware Version ex. 0000 15

Unsigned Integer 16-Bit Battery Cabinet 1 Charger Current

Unsigned Integer 16-Bit Battery cabinet 1 Charger Voltage

Battery Cabinet 1 Ambient

Temperature

Serial #

Serial #

FW Ver.

FW Ver.

FW Ver.

Amps

Volts

°C

Multiplier Comments

X 1 Day Format: DD

X 1 Year Format: YYYY

X 1

X 1

X 1

X 1

X 1 First two character of serial number

X 1

X 1

X 1

X 1

X 1

X 1

X 0.01 x 0.1

X 1

Third and fourth characters of serial number

Fifth and sixth characters of serial number

Last two characters of serial number

First two characters of Firmware

Version

Third and fourth characters of Firmware

Version

Last two characters of Firmware Version

RemotEye III User Manual – 62330-005 139

Registers

30189

30190

30191

30192

30193

30194

30195

30196

30197

30198

30199

30200

Data Type

Signed Integer

ASCII String

ASCII String

ASCII String

ASCII String

ASCII String

Size Description

16-Bit

Battery Cabinet 1 Ambient

Temperature

16-Bit

Battery Cabinet 2 Serial Number

UH 23XXX1

16-Bit

16-Bit

16-Bit

16-Bit

Battery Cabinet 2 Serial Number

UH 23 XXX1

Battery Cabinet 2 Serial Number

UH23 XX X1

Battery Cabinet 2 Serial Number

UH23XX X1

Battery Cabinet 2 Firmware Version ex.

00 0015

ASCII String

Signed Integer

16-Bit

16-Bit

Battery Cabinet 2 Firmware Version ex. 00 00 15

ASCII String

Signed Integer

16-Bit

16-Bit

Battery Cabinet 2 Firmware Version ex. 0000 15

Unsigned Integer 16-Bit Battery Cabinet 2 Charger Current

Unsigned Integer 16-Bit Battery cabinet 2 Charger Voltage

Battery Cabinet 2 Ambient

Temperature

Battery Cabinet 2 Ambient

Temperature

Units

°F

Serial #

Serial #

Serial #

Serial #

FW Ver.

FW Ver.

FW Ver.

Amps

Volts

°C

°F

30201 Signed Integer 16-Bit Temperature in Celsius °C

30202 Signed Integer 16-Bit Temperature Fahrenheit °F

30203 Signed Integer 16-Bit Humidity %

Multiplier Comments

x 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 0.01 x 0.1

X 1

First two character of serial number

Third and fourth characters of serial number

Fifth and sixth characters of serial number

Last two characters of serial number

First two characters of Firmware

Version

Third and fourth characters of Firmware

Version

Last two characters of Firmware Version x 1

X 1

X 1

X 1

Note: "-1" means disabled or not connected

Note: "-1" means disabled or not connected

Note: "-1" means disabled or not connected

140 RemotEye III User Manual – 62330-005

30208

30209

30210

30211

30212

30213

30214

30215

30216

30217

30218

Registers

30204

30205

30206

30207

30219

Data Type Size Description Units

Unsigned Integer 16-Bit UPS History System Operation Time Days

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

Unsigned Integer 16-Bit

UPS History Inverter Operation

Time

Days

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

Unsigned Integer 16-Bit UPS History Backup Operation Time Mins

Unsigned Integer 16-Bit UPS Lifetime Remaining

N/A N/A N/A

N/A

N/A

N/A

N/A

N/A

N/A

Months

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

Signed Integer 16-Bit

UPS History Highest System

Temperature

°C

30220 Signed Integer 16-Bit

UPS History Highest System

Temperature

°F

30221

30222

30223

30224

Signed Integer

Signed Integer

Unsigned Integer

Unsigned Integer

16-Bit

16-Bit

16-Bit

16-Bit

UPS History Highest Battery

Temperature

UPS History Highest Battery

Temperature

UPS History Total Number Input

Under Voltage

UPS History Total Number

Overloads

°C

°F

Times

Times

RemotEye III User Manual – 62330-005

Multiplier Comments

X 1 RE3 Convert Seconds -> Days

N/A

N/A

X 1 RE3 Convert Seconds -> Days

N/A

N/A

X 1

X 1

N/A

N/A

N/A

N/A

N/A

N/A

N/A

X 1

RE3 Convert Seconds -> Minutes

X 1

X 1

X 1

X 1

X 1

141

Registers

30225

30226

30227

30228

30229

30230

30231

Data Type Size Description

Unsigned Integer 16-Bit UPS History Total Number Tests

Units

Times

Unsigned Integer 16-Bit UPS History Total Number Backup Times

Unsigned Integer 16-Bit UPS History Total Number Faults Times

Unsigned Integer

Unsigned Integer

Unsigned Integer

16-Bit

16-Bit

16-Bit

UPS History Total Number

Operation Mode Change

UPS History Total Number

Warnings

UPS History Total Number System

Settings Changed

Unsigned Integer 16-Bit UPS History Total Number Resets

Times

Times

Times

Times

Multiplier Comments

X 1

X 1

X 1

X 1

X 1

X 1

X 1

142 RemotEye III User Manual – 62330-005

Modbus Input Coil for 1600XP: ALARMS and STATUS

NOTE: Items Lined out (e.g. Lined Out) are not supported at this time.

Registers Data Type Size Description Units

10001 Discrete 1-Bit RemotEye III Data Link True/False (1/0)

Comments

0 = Link Up; 1 = Link Down

10002

10003

10004

10005

10006

Discrete

Discrete

Discrete

Discrete

1-Bit RemotEye III Network Link

1-Bit Startup Mode

1-Bit Online Mode

1-Bit Backup Mode

Discrete 1-Bit Bypass Mode

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

0 = Link Up; 1 = Link Down

Reflects Bypass Mode when: BYP Normal, BYP Init, & BYP

Shutdown

10007

10008

10009

10010

10011

10012

10013

10014

Discrete 1-Bit Shutdown Mode

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

1-Bit Battery Test Mode

1-Bit UPS Battery Status Unknown

1-Bit UPS Battery Status Normal

1-Bit UPS Battery Status Low

1-Bit UPS Battery Status Depleted

1-Bit UPS Battery Status Discharging

1-Bit UPS Battery Status Failure

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

Reflects Shutdown Mode when: Shutdown, Initial Charge, &

Boost up

RemotEye III User Manual – 62330-005 143

Registers Data Type Size Description

10015 N/A N/A N/A

10016 N/A

10017

10018

Discrete

Discrete

N/A N/A

1-Bit

1-Bit

Battery Charger Status Normal

Charging

Battery Charger Status Preventative

Charging

10019 Discrete

Units

N/A

N/A

True/False (1/0)

True/False (1/0)

1-Bit Battery Charger Status Stop Charging True/False (1/0)

Comments

10020 N/A N/A N/A N/A

10021 Discrete 1-Bit Battery Test in Progress

10022 Discrete 1-Bit Ok to Perform Battery Test

10023 Discrete 1-Bit Last Battery Test Result

True/False (1/0)

True/False (1/0)

1 = Currently Testing; 0 = Not Testing

1= Ok to perform; 0 = Test prohibited

True/False (1/0)

1 = Passed; 0 = Failed (If no test has been performed it should be blank)

10024 Discrete 1-Bit External Battery Install Status True/False (1/0) 1 = Installed; 0 = Uninstalled

144 RemotEye III User Manual – 62330-005

Registers Data Type Size Description

10025 Discrete 1-Bit Battery Cabinet 1 Enabled

Units Comments

True/False (1/0) 1 = Enabled; 0 = Disabled

10026 Discrete 1-Bit Battery Cabinet 2 Enabled

10027

10028

Discrete 1-Bit EMD Enabled

Discrete 1-Bit EMD Alarm-1

True/False (1/0) 1 = Enabled; 0 = Disabled

True/False (1/0)

True/False (1/0) 0 = no Alarm; 1 = Alarm Triggered

10029

10030

10031

10032

10033

10034

10035

10036

10037

10038

10039

10040

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

1-Bit EMD Alarm-2 True/False (1/0)

1-Bit General Alarm Fault

1-Bit Open Fuse Fault

1-Bit Current Limit Fault

1-Bit Output Overcurrent Fault

1-Bit DC Bus Overcurrent Fault

1-Bit DC Bus Overvoltage Fault

1-Bit DC Bus Imbalance Fault

1-Bit

1-Bit

DC Bus Under Voltage During Boostup Fault

DC Bus Under Voltage During

Charging Fault

1-Bit Charger Overvoltage Fault

1-Bit Output Under voltage Fault

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

0 = no Alarm; 1 = Alarm Triggered

1 = One or more fault reported, see below for cause; 0 = No

Faults

RemotEye III User Manual – 62330-005 145

10051

10052

10053

10054

10055

10056

10057

10058

10059

10060

10061

10062

Registers Data Type Size Description

10041

10042

Discrete

Discrete

1-Bit

1-Bit

Output Overvoltage Fault

Heatsink Overheat Fault

10043

10044

10045

10046

10047

10048

10049

10050

N/A

Discrete

Discrete

Discrete

Discrete

N/A

N/A

N/A

N/A

1-Bit

1-Bit

1-Bit

1-Bit

N/A

N/A

N/A

N/A

Bypass Overload Fault

Resettable Inverter Overload Fault

Un-Resettable Inverter Overload Fault

Bypass Overheat Fault

N/A

N/A

N/A

Units

True/False (1/0)

True/False (1/0)

N/A

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

N/A

N/A

N/A

10063

10064

10065

Discrete

Discrete

Discrete

N/A

Discrete

Discrete

Discrete

N/A

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

1-Bit

1-Bit

1-Bit

N/A

1-Bit

1-Bit

1-Bit

N/A

1-Bit

1-Bit

1-Bit

Input Overvoltage Warning

Input Under voltage Warning

Input Frequency Error Warning

N/A

Bypass Overvoltage Warning

Bypass Under voltage Warning

Bypass Input Frequency Error Warning

N/A

Output Overload Warning

Current Limit Warning

Battery Test Failed Warning

1-Bit Low Battery Level Reached Warning

1-Bit

Shutdown Battery Level Reached

Warning

1-Bit Replace Battery Warning

1-Bit Battery Overheat Warning

True/False (1/0)

True/False (1/0)

True/False (1/0)

N/A

True/False (1/0)

True/False (1/0)

True/False (1/0)

N/A

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

10066 Discrete 1-Bit

Battery Near Expiration Warning

(Replace batteries soon)

True/False (1/0)

Comments

146 RemotEye III User Manual – 62330-005

Registers Data Type Size Description

10067

10068

10069

10070

10071

10072

10073

10074

10075

10076

10077

10078

Discrete

N/A

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

N/A

Discrete

Discrete

Discrete

Units

1-Bit

Battery Expired Warning (Replace

Batteries)

N/A N/A

1-Bit Battery Depleted Warning

1-Bit Charger Overvoltage Warning

True/False (1/0)

N/A

True/False (1/0)

True/False (1/0)

1-Bit

1-Bit

DC Bus Under Voltage During Battery

Test Warning

1-Bit System Test Failed Warning

1-Bit System Overheat Warning

1-Bit Asynchronous Operation Warning

N/A N/A

1-Bit Service UPS Soon Warning

1-Bit Display Cable Error Warning

Display and UPS Communication Error

Warning

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

N/A

True/False (1/0)

True/False (1/0)

True/False (1/0)

10079 Discrete 1-Bit

UPS and RemotEye Communication

Error Warning

True/False (1/0)

10080

10081

10082

10083

10084

Discrete

Discrete

N/A

N/A

N/A

1-Bit

RemotEye and Network

Communication Error Warning

1-Bit

UPS and Service Port Communication

Error Warning

N/A N/A

N/A N/A

N/A N/A

True/False (1/0)

True/False (1/0)

N/A

N/A

N/A

10085 Discrete 1-Bit EMD Sensor 1 Alarm Triggered True/False (1/0)

Comments

10086 Discrete 1-Bit EMD Sensor 2 Alarm Triggered True/False (1/0)

RemotEye III User Manual – 62330-005 147

10105

10106

10107

10108

10109

10110

10111

10097

10098

10099

10100

10101

10102

10103

10104

Registers Data Type Size Description

10087

10088

10089

10090

10091

10092

10093

10094

10095

10096

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

N/A

1-Bit

1-Bit

EMD Humidity is at Low Critical Point

EMD Humidity is at High Critical

Point

Units

True/False (1/0)

True/False (1/0)

1-Bit EMD Humidity at Low Warning Point True/False (1/0)

1-Bit EMD Humidity at High Warning Point True/False (1/0)

1-Bit

1-Bit

1-Bit

1-Bit

EMD Temperature at Low Critical

Point

EMD Temperature at High Critical

Point

EMD Temperature at Low Warning

Point

EMD Temperature at High Warning

Point

1-Bit Input Power Failure

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

N/A N/A N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A N/A

N/A N/A

N/A N/A

N/A N/A

N/A N/A

N/A N/A

N/A N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

Comments

148 RemotEye III User Manual – 62330-005

Registers Data Type Size Description

10112

10113

10114

N/A

Discrete

Discrete

N/A

1-Bit

1-Bit

N/A

UPS Output Shutdown in Progress

UPS Output is Off

10115

10116

10117

10118

10119

10120

10121

10122

10123

10124

10125

10126

10127

10128

10129

10130

10131

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Units

N/A

True/False (1/0)

True/False (1/0)

1-Bit

Unsuccessful Login

(Username/Password incorrect)

True/False (1/0)

1-Bit

1-Bit

1-Bit

1-Bit

1-Bit

1-Bit

1-Bit

Battery Cabinet 1 String 1

Disconnected

Battery Cabinet 1 String 2

Disconnected

Battery Cabinet 1 String 3

Disconnected

Battery Cabinet 1 String 1 Loose HCT

Connection

Battery Cabinet 1 String 2 Loose HCT

Connection

Battery Cabinet 1 String 3 Loose HCT

Connection

Battery Cabinet 1 Over Temperature

Warning

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

1-Bit Reserved

1-Bit

1-Bit

Battery Cabinet 1 Charger Over

Voltage Fault

Battery Cabinet 1 Charger Over

Current Fault

True/False (1/0)

True/False (1/0)

True/False (1/0)

1-Bit Battery Cabinet 1 Lost Communication True/False (1/0)

1-Bit

1-Bit

1-Bit

1-Bit

Battery Cabinet 2 String 1

Disconnected

Battery Cabinet 2 String 2

Disconnected

Battery Cabinet 2 String 3

Disconnected

Battery Cabinet 2 String 1 Loose HCT

Connection

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

1-Bit Battery Cabinet 2 String 2 Loose HCT True/False (1/0)

Comments

RemotEye III User Manual – 62330-005 149

Registers Data Type Size Description

Connection

10132

10133

10134

10135

10136

10137

Discrete

Discrete

Discrete

Discrete

Discrete

Discrete

Units

1-Bit

1-Bit

Battery Cabinet 2 String 3 Loose HCT

Connection

Battery Cabinet 2 Over Temperature

Warning

True/False (1/0)

True/False (1/0)

1-Bit Reserved

1-Bit

1-Bit

Battery Cabinet 2 Charger Over

Voltage Fault

Battery Cabinet 2 Charger Over

Current Fault

True/False (1/0)

True/False (1/0)

True/False (1/0)

1-Bit Battery Cabinet 2 Lost Communication True/False (1/0)

Comments

150 RemotEye III User Manual – 62330-005

Modbus Input Register for 4200FA/4300: MONITORING

NOTE: Items Lined out (e.g. Lined Out) are not supported at this time.

Registers Data Type

30001 Unsigned Integer

30002 Unsigned Integer

30003 Unsigned Integer

30004 Unsigned Integer

30005 Unsigned Integer

30006 Unsigned Integer

30007 Unsigned Integer

30008 Unsigned Integer

30009 Unsigned Integer

30010 Unsigned Integer

30011 Unsigned Integer

30012 Unsigned Integer

30013 Unsigned Integer

30014 Unsigned Integer

30015 Unsigned Integer

30016 Unsigned Integer

30017 Unsigned Integer

30018 Unsigned Integer

30019 Unsigned Integer

30020 Unsigned Integer

30021 Unsigned Integer

Size

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

Description

RemotEye III Software Version

RemotEye III Slave ID Number

IP Address First Byte

IP Address Second Byte

IP Address Third Byte

IP Address Fourth Byte

Subnet Mask First Byte

Subnet Mask Second Byte

Subnet Mask Third Byte

Subnet Mask Fourth Byte

Gateway IP Address First Byte

Gateway IP Address Second Byte

Gateway IP Address Third Byte

Gateway IP Address Fourth Byte

RemotEye III Installation Date

RemotEye III Installation Date

RemotEye III Installation Date

Date on RemotEye III

Date on RemotEye III

Date on RemotEye III

Time on RemotEye III

30022 Unsigned Integer 16-Bit Time on RemotEye III

30023 Unsigned Integer 16-Bit Time on RemotEye III

Units

Firmware

ID

IP Address

IP Address

IP Address

IP Address

Subnet Mask

Subnet Mask

Subnet Mask

Subnet Mask

IP Address

IP Address

IP Address

IP Address

Month

Day

Year

Month

Day

Year

Hour

Minute

Seconds

Multiplier Comments

X 1

X 1

X 1 Example: "192" from 192.168.1.150

X 1 Example: "168" from 192.168.1.150

X 1

X 1

X 1

X 1

X 1

Example: "1" from 192.168.1.150

Example: "150" from 192.168.1.150

Example: "255" from 255.255.255.0

Example: "255" from 255.255.255.0

Example: "255" from 255.255.255.0

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

Example: "0" from 255.255.255.0

Example: "192" from 192.168.1.1

Example: "168" from 192.168.1.1

Example: "1" from 192.168.1.1

Example: "1" from 192.168.1.1

Month Format: MM

Day Format: DD

Year Format: YYYY

Month Format: MM

Day Format: DD

Year Format: YYYY

X 1 Hour Format: HH

X 1 Minute Format: MM

X 1 Seconds Format: SS

RemotEye III User Manual – 62330-005 151

Registers Data Type

30024 ASCII String

30025 ASCII String

30026 ASCII String

30027 ASCII String

30028 ASCII String

30029 ASCII String

30030 ASCII String

30031 ASCII String

30032 ASCII String

30033 ASCII String

30034 ASCII String

30035 ASCII String

30036 ASCII String

30037 ASCII String

30038 ASCII String

30039 ASCII String

30040 ASCII String

30041 ASCII String

152

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

Size

16-Bit

Description

Manufacture (first two characters)

Manufacture (third and fourth two characters)

Manufacture (fifth and sixth characters)

Manufacture (seventh characters)

UPS Typeform (first two characters)

UPS Typeform (third and fourth characters)

UPS Typeform (fifth and sixth characters)

UPS Typeform (seventh and eighth characters)

UPS Typeform (ninth and tenth characters)

UPS Typeform (eleventh and twelve characters)

UPS Typeform (thirteen and fourteen characters)*

UPS Typeform (fifteen and sixteen characters)*

UPS Serial Number (first two characters)

UPS Serial Number (third and fourth characters)

UPS Serial Number (fifth and sixth characters)

UPS Serial Number (seventh and eighth characters)

UPS Serial Number (ninth and tenth characters)

UPS Serial Number (eleventh and twelve characters)

Units

Characters

Characters

Characters

Characters

Characters

Characters

Characters

Characters

Characters

Characters

Characters

Characters

Characters

Characters

Characters

Characters

Characters

Characters

None

None

None

None

None

None

None

None

None

None

None

None

None

None

None

None

None

Multiplier Comments

None Constant: "To" from To shiba

Constant: "sh" from To sh iba

Constant: "ib" from Tosh ib a

Constant: "a" from Toshib a

UPS Typeform Example:

43 10F3F500FAXXXX

UPS Typeform Example:

43 10 F3F500FAXXXX

UPS Typeform Example:

4310 F3 F500FAXXXX

UPS Typeform Example:

4310F3 F5 00FAXXXX

UPS Typeform Example:

4310F3F5 00 FAXXXX

UPS Typeform Example:

4310F3F500 FA XXXX

UPS Typeform Example:

4310F3F500FA XX XX

UPS Typeform Example:

4310F3F500FAXX XX

Serial # Example: 20 12101234567891

Serial # Example: 20 12 101234567891

Serial # Example: 2012 10 1234567891

Serial # Example: 201210 12 34567891

Serial # Example: 20121012 34 567891

Serial # Example: 2012101234 56 7891

RemotEye III User Manual – 62330-005

Registers Data Type

30042 ASCII String

30043 ASCII String

30044 Unsigned Integer

30045 Unsigned Integer

30046 Unsigned Integer

30047 Unsigned Integer

30048 Unsigned Integer

30049 Unsigned Integer

30050 Unsigned Integer

30051 N/A

30052 N/A

30053 N/A

30054 N/A

30055 N/A

30056 N/A

30057 N/A

30058 Unsigned Integer

30059 Unsigned Integer

30060 Unsigned Integer

30061 Unsigned Integer

30062 Unsigned Integer

30063 Unsigned Integer

30064 Unsigned Integer

30065 Unsigned Integer

Size

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

N/A

N/A

N/A

N/A

N/A

N/A

N/A

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

Description

UPS Serial Number (thirteen and fourteen characters)

UPS Serial Number (fifteen and sixteen characters)

UPS Capacity

UPS Installation Date

UPS Installation Date

UPS Installation Date

UPS Display Firmware Built Date

UPS Display Firmware Built Date

UPS Display Firmware Built Date

N/A

N/A

N/A

N/A

N/A

N/A

N/A

Input Numbers of Phases

Input Voltage Phase A (L-L)

Input Voltage Phase B (L-L)

Input Voltage Phase C (L-L)

Input Voltage Phase AB (L-N)

Input Voltage Phase BC (L-N)

Input Voltage Phase CA (L-N)

Input Voltage Percent Phase A

Volts

Volts

Volts

Volts

Volts

Volts

%

Units

Characters

Characters kVA

Month

Day

Year

Month

Day

Year

N/A

N/A

N/A

N/A

N/A

N/A

N/A

Phase

X 1

X 1

X 1

X 1

X 1

X 1

X 1

Multiplier Comments

None Serial # Example: 201210123456 78 91

Serial # Example: 20121012345678 91 None

X 1

X 1

X 1

X 1

X 1

X 1

X 1

N/A

N/A

N/A

N/A

N/A

N/A

N/A

X 1

Month Format: MM

Day Format: DD

Year Format: YYYY

Month Format: MM

Day Format: DD

Year Format: YYYY

N/A

N/A

N/A

N/A

N/A

N/A

N/A

RemotEye III User Manual – 62330-005 153

Registers Data Type

30066 Unsigned Integer

30067 Unsigned Integer

30068 Unsigned Integer

30069 Unsigned Integer

30070 Unsigned Integer

30071 N/A

30072 Unsigned Integer

30073 Unsigned Integer

30074 Unsigned Integer

30075 Unsigned Integer

30076 Unsigned Integer

30077 Unsigned Integer

30078 N/A

30079 N/A

30080 N/A

30081 Unsigned Integer

30082 N/A

30083 N/A

30084 Unsigned Integer

30085 N/A

30086 Unsigned Integer

30087 Unsigned Integer

30088 Unsigned Integer

30089 Unsigned Integer

30090 Unsigned Integer

30091 Unsigned Integer

Size

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

N/A

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

N/A

N/A

N/A

16-Bit

N/A

N/A

16-Bit

N/A

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

Description

Input Voltage Percent Phase B

Input Voltage Percent Phase C

Input Rated Voltage (L-L)

Input Rated Voltage (L-N)

Input Current

N/A

Input Rated Current

Input Frequency Phase A

Input Frequency Phase B

Input Frequency Phase C

Voltage Input Under Voltage

Detection Level

Voltage Input Over Voltage Detection

Level

N/A

N/A

N/A

Input Rated Active Power

N/A

N/A

Input Rated Apparent Power

N/A

Output Number of Phases

Output Voltage Phase A (L-L)

Output Voltage Phase B (L-L)

Output Voltage Phase C (L-L)

Output Rated Voltage (L-L)

Output Voltage Phase AB (L-N)

%

N/A

N/A

N/A

KWatts

N/A

N/A

KVA

N/A

Phase

Volts

Volts

Volts

Volts

Volts

Units

%

%

Volts

Volts

Amps

N/A

Amps

Hz

Hz

Hz

%

154

X 1

X 1

N/A

X 1

X 1

X 1

X 1

X 1

X 1

N/A

N/A

N/A

X 1

N/A

N/A

Multiplier Comments

X 1

X 1

X 1

X 1

X 1

N/A

X 0.1

X 0.1

X 0.1

X 0.1

X 1

RemotEye III User Manual – 62330-005

Registers Data Type

30092 Unsigned Integer

30093 Unsigned Integer

30094 Unsigned Integer

30095 Unsigned Integer

30096 Unsigned Integer

30097 Unsigned Integer

30098 Unsigned Integer

30099 Unsigned Integer

30100 N/A

30101 N/A

30102 N/A

30103 Unsigned Integer

30104 Unsigned Integer

30105 Unsigned Integer

30106 Unsigned Integer

30107 Unsigned Integer

30108 Unsigned Integer

30109 Unsigned Integer

30110 N/A

30111 Unsigned Integer

30112 Unsigned Integer

30113 Unsigned Integer

30114 Unsigned Integer

30115 N/A

30116 N/A

30117 N/A

30118 Unsigned Integer

N/A

16-Bit

16-Bit

16-Bit

16-Bit

N/A

N/A

N/A

16-Bit

N/A

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

Size

16-Bit

16-Bit

16-bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

N/A

N/A

Description

Output Voltage Phase BC (L-N)

Output Voltage Phase CA (L-N)

Units

Volts

Volts

Output Rated Voltage (L-N)

Output Voltage Phase A

Output Voltage Phase B

Output Voltage Phase C

Volts

%

%

%

Output Under Voltage Detection Level Volts

Output Over Voltage Detection Level Volts

N/A

N/A

N/A

N/A

N/A

Output Current Phase A

Output Current Phase B

Output Current Phase C

Output Current Phase A

Output Current Phase B

Output Current Phase C

Output Total Current

N/A

Output Rated Current

Output Frequency Phase A

Output Frequency Phase B

Output Frequency Phase C

N/A

N/A

N/A

Output Total Active Power

N/A

Amps

Hz

Hz

Hz

N/A

N/A

N/A

KWatts

%

%

%

%

N/A

Amps

Amps

Amps

N/A

X 1

X 0.1

X 0.1

X 0.1

N/A

N/A

N/A

X 1

N/A

X 1

X 1

X 1

X 1

X 1

X 1

X 1

Multiplier Comments

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

N/A

N/A

RemotEye III User Manual – 62330-005 155

Registers Data Type

30119 Unsigned Integer

30120 Unsigned Integer

30121 N/A

30122 N/A

30123 Unsigned Integer

30124 Unsigned Integer

30125 N/A

30126 Unsigned Integer

30127 Unsigned Integer

30128 Unsigned Integer

30129 Unsigned Integer

30130 Unsigned Integer

30131 Unsigned Integer

30132 Unsigned Integer

30133 Unsigned Integer

30134 Unsigned Integer

30135 Unsigned Integer

30136 Unsigned Integer

30137 Unsigned Integer

30138 N/A

30139 N/A

30140 N/A

30141 N/A

30142 Unsigned Integer

30143 Unsigned Integer

30144 Unsigned Integer

30145 N/A

Size

16-Bit

16-Bit

N/A

N/A

16-Bit

16-Bit

N/A

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

N/A

N/A

N/A

N/A

16-Bit

16-Bit

16-Bit

N/A

Description

Output Total Active Power Percent

Output Rated Active Power

N/A

N/A

Output Rated Apparent Power

Output Power Factor

N/A

Bypass Number of Phases

Bypass Voltage Phase A (L-L)

Bypass Voltage Phase B (L-L)

Bypass Voltage Phase C (L-L)

Bypass Voltage Phase AB (L-N)

Bypass Voltage Phase BC (L-N)

Bypass Voltage Phase CA (L-N)

Volts

Volts

Volts

Volts

Bypass Voltage Phase A

Bypass Voltage Phase B

%

%

Bypass Voltage Phase C

Bypass Under Voltage Detection

Level

%

%

Bypass Over Voltage Detection Level %

N/A

N/A

N/A

N/A

N/A

N/A

N/A

Bypass Frequency Phase 1

Bypass Frequency Phase 2

Bypass Frequency Phase 3

N/A

N/A

Hz

Hz

Hz

N/A

Units

%

KWatts

N/A

N/A

KVA

PF

N/A

Phase

Volts

Volts

156

X 1

N/A

N/A

N/A

N/A

X 0.1

X 0.1

X 0.1

N/A

Multiplier Comments

X 1

X 1

N/A

N/A

X 1

X 0.01

N/A

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

RemotEye III User Manual – 62330-005

Registers Data Type

30146 N/A

30147 Unsigned Integer

30148 N/A

30149 N/A

30150 N/A

30151 Unsigned Integer

30152 Unsigned Integer

30153 Unsigned Integer

30154 N/A

30155 N/A

30156 Unsigned Integer

30157 N/A

30158 Unsigned Integer

30159 N/A

30160 Unsigned Integer

30161 N/A

30162 Unsigned Integer

30163 Unsigned Integer

30164 Unsigned Integer

30165 N/A

30166 N/A

30167 N/A

30168 N/A

30169 Unsigned Integer

30170 Unsigned Integer

30171 Unsigned Integer

16-Bit

N/A

N/A

N/A

N/A

16-Bit

Size

N/A

16-Bit

N/A

N/A

N/A

16-Bit

16-Bit

16-Bit

N/A

N/A

16-Bit

N/A

16-Bit

N/A

16-Bit

N/A

16-Bit

16-Bit

16-Bit

16-Bit

Description

N/A

DC Bus Total Voltage

N/A

N/A

N/A

Battery Installation Date

Battery Installation Date

Battery Installation Date

N/A

N/A

Elapsed Time on Battery Power

N/A

Battery Voltage

N/A

Battery Discharge Current

N/A

Battery Low Detection Level

Float Charge Voltage

Equalize Charge Time

N/A

N/A

N/A

N/A

Battery Rated Ampere Hour

Batteries in Series

Batteries in Parallel

Hours

N/A

N/A

N/A

N/A

Ahr

Units

N/A

Volts

N/A

N/A

N/A

Month

Day

Year

N/A

N/A

Seconds

N/A

Vdc

N/A

Adc

N/A

Vdc

Vdc

Batteries

Batteries

X 1

N/A

X 1

N/A

X 1

N/A

X 1

X 1

Multiplier Comments

N/A

X 1

N/A

N/A

N/A

X 1

X 1

X 1

N/A

N/A

Month Format: MM

Day Format: DD

Year Format: YYYY

X 1

N/A

N/A

N/A

N/A

X 1

X 1

X 1

RemotEye III User Manual – 62330-005 157

Registers Data Type

30172 N/A

30173 N/A

30174 N/A

30175 N/A

30176 N/A

30177 N/A

30178 N/A

30179 N/A

30180 N/A

30181 N/A

30182 N/A

30183 N/A

30184 N/A

30185 N/A

30186 N/A

30187 N/A

30188 N/A

30189 N/A

30190 N/A

30191 N/A

30192 N/A

30193 N/A

30194 N/A

30195 N/A

30196 N/A

30197 N/A

30198 N/A

158

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

Description

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

Size

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

Units

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

Multiplier Comments

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

RemotEye III User Manual – 62330-005

Registers Data Type

30199 N/A

30200 N/A

30201 Signed Integer

30202 Signed Integer

30203 Signed Integer

30204 Unsigned Integer

30205 Unsigned Integer

30206 Unsigned Integer

30207 Unsigned Integer

30208 Unsigned Integer

30209 Unsigned Integer

30210 N/A

30211 N/A

30212 N/A

30213 N/A

30214 N/A

30215 N/A

30216 N/A

30217 N/A

30218 N/A

30219 N/A

30220 N/A

30221 N/A

30222 N/A

30223 N/A

30224 N/A

30225 N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

16-Bit

N/A

N/A

N/A

N/A

N/A

N/A

N/A

Size

N/A

N/A

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

16-Bit

Description

N/A

N/A

Units

N/A

N/A

Temperature in Celsius

Temperature Fahrenheit

°C

°F

Humidity %

UPS History System Operation Time Days

UPS History System Operation Time Hours

UPS History System Operation Time Mins

UPS History Inverter Operation Time Days

UPS History Inverter Operation Time Hours

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

UPS History Inverter Operation Time Mins

N/A N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

RemotEye III User Manual – 62330-005

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

X 1

N/A

N/A

N/A

N/A

N/A

N/A

N/A

Multiplier Comments

N/A

N/A

X 1

X 1

X 1

X 1

X 1

X 1

X 1

X 1

159

Registers Data Type

30226 Unsigned Integer

30227 Unsigned Integer

30228 Unsigned Integer

30229 N/A

30230 N/A

30231 N/A

Size

16-Bit

16-Bit

16-Bit

N/A

N/A

N/A

Description Units

UPS History Total Number of

Backups

Times

UPS History Total Number of Faults Times

UPS History Total Number Operation

Mode Change

Times

N/A

N/A

N/A

N/A

N/A

N/A

Multiplier Comments

X 1

X 1

X 1

N/A

N/A

N/A

160 RemotEye III User Manual – 62330-005

Modbus Input Coil for 4200FA/4300: ALARMS and STATUS

NOTE: Items Lined out (e.g. Lined Out) are not supported at this time.

Registers Data Type

10001 Discrete

Size Description

1-Bit RemotEye III Data Link

Units

True/False (1/0)

10002 Discrete

10003 N/A

10004 Discrete

10005 Discrete

10006 Discrete

10007 Discrete

10008 N/A

10009 Discrete

10010 Discrete

10011 Discrete

10012 Discrete

10013 Discrete

10014 Discrete

10015 Discrete

10016 Discrete

10017 N/A

10018 N/A

10019 N/A

1-Bit RemotEye III Network Link

N/A N/A

1-Bit Online Mode

1-Bit Backup Mode

1-Bit Bypass Mode

1-Bit Shutdown Mode

N/A N/A

1-Bit UPS Battery Status Unknown

1-Bit UPS Battery Status Normal

1-Bit UPS Battery Status Low

1-Bit UPS Battery Status Depleted

1-Bit UPS Battery Status Discharging

1-Bit UPS Battery Status Test Failure

1-Bit Protective Charging Set

1-Bit Equalized Charging Set

N/A

N/A

N/A

N/A

N/A

N/A

True/False (1/0)

N/A

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

N/A

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

N/A

N/A

N/A

Comments

0 = Link Up; 1 = Link Down

0 = Link Up; 1 = Link Down

RemotEye III User Manual – 62330-005 161

Registers Data Type

10020 Discrete

10021 Discrete

10022 N/A

10023 N/A

10024 N/A

10025 N/A

10026 N/A

10027 Discrete

10028 Discrete

10029 Discrete

10030 Discrete

10031 Discrete

10032 Discrete

10033 N/A

10034 Discrete

10035 Discrete

10036 Discrete

10037 Discrete

10038 Discrete

10039 Discrete

10040 Discrete

10041 Discrete

10042 Discrete

10043 Discrete

10044 N/A

10045 N/A

Size Description

1-Bit Battery Test Disabled

1-Bit Battery Test in Progress

N/A

N/A

N/A

N/A

N/A N/A

Units

True/False (1/0)

True/False (1/0)

N/A

N/A

N/A

N/A N/A

N/A N/A

1-Bit EMD Enabled

1-Bit EMD Alarm-1

1-Bit EMD Alarm-2

1-Bit General Alarm Fault

1-Bit Open Fuse Fault

1-Bit Current Limit Fault

N/A N/A

1-Bit DC Bus Overcurrent Fault

1-Bit DC Bus Overvoltage Fault

1-Bit DC Bus Imbalance Fault

1-Bit

1-Bit

DC Bus Under Voltage During Boostup Fault

DC Bus Under Voltage During

Charging Fault

1-Bit Charger Overvoltage Fault

1-Bit Output Under Voltage Fault

1-Bit Output Overvoltage Fault

1-Bit Heatsink Overheat Fault

1-Bit UPS Overload Fault

N/A N/A

N/A N/A

N/A

N/A

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

N/A

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

N/A

N/A

N/A

N/A

Comments

0 = no Alarm; 1 = Alarm Triggered

0 = no Alarm; 1 = Alarm Triggered

0 = No Faults, 1 = One or more fault reported, see below for cause;

162 RemotEye III User Manual – 62330-005

Registers Data Type

10046 N/A

10047 Discrete

10048 Discrete

10049 Discrete

10050 Discrete

10051 Discrete

10052 Discrete

10053 N/A

10054 Discrete

10055 Discrete

10056 Discrete

10057 Discrete

10058 Discrete

10059 Discrete

10060 Discrete

10061 Discrete

10062 Discrete

10063 Discrete

10068 Discrete

10069 N/A

10070 Discrete

10071 N/A

10072 Discrete

10073 Discrete

10076 N/A

10078 N/A

10079 Discrete

10087 Discrete

Size

N/A

Description

N/A

1-Bit Bypass Overheat Fault

1-Bit Output Overcurrent Fault

1-Bit Input Phase Rotation Error

1-Bit Bypass Phase Rotation Error

1-Bit Input Overvoltage Warning

1-Bit Input Under voltage Warning

Units

N/A

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

N/A N/A

1-Bit Input MCCB Tripped Warning

1-Bit Bypass Overvoltage Warning

1-Bit Bypass Under voltage Warning

N/A

True/False (1/0)

True/False (1/0)

True/False (1/0)

1-Bit

Bypass Input Frequency Error

Warning

1-Bit Inverter Overload Warning

True/False (1/0)

1-Bit Output Overload Warning

1-Bit Current Limit Warning

1-Bit Battery Test Failed Warning

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

1-Bit Low Battery Level Reached Warning True/False (1/0)

1-Bit

Shutdown Battery Level Reached

Warning

True/False (1/0)

1-Bit Battery MCCB is Off Warning

N/A N/A

1-Bit Charger Overvoltage Warning

N/A N/A

1-Bit System Test Failed Warning

1-Bit System Overheat Warning

N/A

N/A

N/A

N/A

1-Bit

UPS and RemotEye Communication

Error Warning

1-Bit

EMD Humidity is at Low Critical

True/False (1/0)

N/A

True/False (1/0)

N/A

True/False (1/0)

True/False (1/0)

N/A

N/A

True/False (1/0)

True/False (1/0)

Comments

N/A

RemotEye III User Manual – 62330-005 163

Registers Data Type

10088 Discrete

10089 Discrete

10090 Discrete

10091 Discrete

10092 Discrete

10093 Discrete

10094 Discrete

10095 Discrete

10096 Discrete

10100 Discrete

10101 Discrete

10102 Discrete

10103 Discrete

10104 Discrete

10105 Discrete

10106 Discrete

10107 Discrete

10108 Discrete

10113 N/A

10114 Discrete

Size Description

Point

Units

1-Bit

EMD Humidity is at High Critical

Point

True/False (1/0)

1-Bit EMD Humidity at Low Warning Point True/False (1/0)

1-Bit

1-Bit

1-Bit

EMD Humidity at High Warning

Point

EMD Temperature at Low Critical

Point

EMD Temperature at High Critical

Point

True/False (1/0)

True/False (1/0)

True/False (1/0)

1-Bit

1-Bit

EMD Temperature at Low Warning

Point

EMD Temperature at High Warning

Point

1-Bit Input Power Failure

1-Bit EPO has Tripped

1-Bit

UPS is Waiting at a Specified Time by

User before Start-up

1-Bit Remote Switch Control Enabled

1-Bit Auto Re-Transfer Enabled

1-Bit Manual Mode Selected

1-Bit

UPS has Immediately switch to inverter at startup

1-Bit UPS has been forced to Bypass

1-Bit Local Run Command Issued

1-Bit Remote Run Command Issued

1-Bit Firmware has been Updated

N/A N/A

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

True/False (1/0)

N/A

1-Bit UPS Output is Off True/False (1/0)

Comments

164 RemotEye III User Manual – 62330-005

INDUSTRIAL DIVISION

13131 West Little York Rd., Houston, TX 77041

Tel: 713/466-0277 Fax 713/466-8773

US 877/867-8773 Canada 800/872-2192 Mexico 01/800/527-1204 www.toshiba.com/ind

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents