ADJUSTMENT. Kenwood TS-2000 X
The TS-2000 X is an all-mode multi-band transceiver that incorporates an IF/AF DSP for satellite communication. It also features an independent FM/AM sub-receiver for the VHF and UHF bands. The main band side has an independent front end for each of the HF, 50MHz, 144MHz, 430MHz and 1.2GHz bands. The sub-band receiver is not used during satellite operation, but it can receive signals while the main band receiver is sending a signal. In addition to the standard features of a transceiver, the TS-2000 X also includes features such as a noise blanker, a digital IF filter, and a digital AGC. It also has a speaker separation function that allows you to output the audio to two separate speakers or headphones. The TS-2000 X is a powerful and versatile transceiver that is suitable for a wide variety of applications, including satellite communication, HF and VHF/UHF operation, and contesting.
Advertisement
Advertisement
TS-2000/X
ADJUSTMENT
Required Test Equipment
1. DC Voltmeter (DC V.M)
1) Input resistance : More than 1M
Ω
2) Voltage range : 1.5 to 1000V AC/DC
Note : A high-recision multimeter may be used. However, accurate readings can not be obtained for highimpedance circuits.
2. DC Ammeter
1) Current range : 100mA, 1.5A, 15A, high-precision ammeter may be used.
3. RF VTVM (RF V.M)
1) Input impedance : 1M
Ω
and less than 3pF, min.
2) Voltage range : 10mV to 300V
3) Frequency range : 10kHz to 500MHz
4. AF Voltmeter (AF V.M)
1) Frequency range : 50Hz to 10kHz
2) Input resistance : 1M
Ω
or greater
3) Voltage range : 10mV to 30V
5. AF Generator (AG)
1) Frequency range : 200Hz to 5kHz
2) Output : 1mV or less to 1V, low distortion
6. AF Dummy Load (DM. SP)
1) Impedance : 8
Ω
2) Dissipation : 3W or greater
7. Oscilloscope
Requires high sensitivity, and external synchronization capability (150MHz or greater).
8. Sweep Generator (Sweep G.)
1) Center frequency : 50kHz to 140MHz
2) Frequency deviation : Maximum
±
35kHz
3) Output voltage : 100mV or greater
9. Standard Signal Generator (SSG)
1) Frequency range : 50kHz to 60MHz
2) Output : –133dBm/0.1
µ
V to 7dBm/1V
3) Output impedance : 50
Ω
4) AM and FM modulation can be possible
Note : Generator must be frequency stable.
10. Frequency Counter (f. counter)
1) Minimum input voltage : 50mV
2) Frequency range : 150MHz or greater
11. Noise Generator (Noise G.)
Must generate ignition noise containing harmonics beyond 30MHz.
12. RF Dummy Load
1) Impedance : 150
Ω
and 50
Ω
2) Dissipation : 150W or greater
13. Linear Detector
1) Frequency range : 60MHz or greater
14. Power Meter
1) Impedance : 50
Ω
2) Dissipation : 300W continuous or greater
3) Frequency limits : 60MHz or greater
15. Spectrum Analyzer
1) Frequency range : 100kHz to 140MHz or greater
2) Bandwidth : 1kHz to 3MHz
16. Detector
1) For adjustment of BPF
IN
To RF unit
OUT
10P 1N60
OUT
To Oscilloscope
IN
2) For adjustment of PLL/VCO BPF
IN
To PLL unit
OUT
5P 1N60
17. Directional Coupler
18. Monitor Receiver
R-1000 class
19. Microphone
MC-43S or MC-60S8
20. Tracking Generator
21. Distortion Meter
22. Double Signal Pad (50
Ω
)
OUT
To Oscilloscope
IN
98
TS-2000/X
ADJUSTMENT
Preparation
Unless otherwise specified, knobs and switches should be set as follows.
POWER ........................................................................... ON
MANUAL BC ............................................................... Center
MAIN RF GAIN ............................................................ MAX
MAIN AF GAIN .............................................................. MIN
NAIN SQL ..................................................................... MIN
SUB AF GAIN ................................................................ MIN
SUB SQL ....................................................................... MIN
■ Front panel
PF
F LOCK A
ATT
PRE
LEVEL
LEVEL
VOX
PROC
ANT1/2
SEND
AT
PHONES LEVEL
N.R.
MIC
LEVEL
A.N.
MANUAL
B.C.
LO/
WIDTH
MAIN
CH1/REC
1
TONE/SEL
4
.
CH2/REC
2
METER
5
CH3/REC
3
CTCSS/SEL
6
NB/LEVEL
7
AGC/OFF
8
SHIFT/OFFSET
0
FINE/STEP
9
ENT
HI/
SHIFT
F
U
N
C
CAR
MIC
TX MONI
PWR
DELAY
KEY
REV
CW
FSK
NAR
FM
AM
AUTO
LSB
USB
CLR
DISP
SEL
1MHz
HF/VHF/UHF ALL MODE MULTI BANDER TS-2000
MENU
SUB
CALL C.IN
CW TUNE
RIT
ALT
XIT
_
CLEAR
P.C.T
SET
QUICK MEMO
MR
M.IN
MANUAL
BC
RF
MAIN
GAIN
TF-
SET
9.6k STA CON
RIT/SUB
MULTI
CH
+
CTRL
MAIN SUB
SG.SEL
SCAN
M/S
A/B
VFO/CH
VFO/M
MG.SEL
M VFO
SA
TL
REV
SPLIT
TRACE
A=B
M.IN
MAIN
AF
SQL
SUB
■ Rear panel
ANT 2
COM
2 1
ANT 1
GND
KEY PADDLE ANT
430
PANEL
EXT. SP2
8
Ω
EXT. SP1
8
Ω
EXT. CONT ACC2 REMOTE
AT
ANT
144
ANT 1.2G
DC
13.8V
HF
RX ANT
99
TS-2000/X
Service Jig
A. Lead wire with minipin plug
(E37-0878-05)
About 56cm
■ How to use
A. Lead wire with minipin plug
CN49
B. Flat cable (16P)
CN10
CN18
CN1
ADJUSTMENT
B. Flat cable (16P)
(E37-0572-05)
About 17cm
Adjustment Mode
■ Outline
1. The TS-2000/X can be adjusted manually (by turning a coil, trimmer, etc.) or by setting the service adjustment mode (adjustment with panel keys). In the service adjustment mode (simply referred to as the adjustment mode below), adjustments items are shown in menu
No.00 to 126 and all data are saved in the EEPROM (X53-
391: IC7).
2. To enter adjustment mode, the user firmware in the main unit must be rewritten with adjustment firmware. (The user firmware is factory-set.)
■ Diagram of uploading the adjustment firmware
1. Checksum confirmation
Switch the transceiver on while pressing and hold [N.R.] and [MIC/CAR] keys.
2. Preparation of uploading the data
1) Access Menu No. 56 and select 9600 bps, then switch the transceiver OFF.
Turn the transceiver ON again.
2) Back up the user data in the transceiver (Menu configuration and Memory channel data)
Run the programming software (W05-0855-00), then select
“Menu/MRch READ from RADIO”
Name the file that can be identified easily.
(Such as a serial number)
3. Uploading the adjustment firmware
1) Turn the switch (S1) ON in TX-RX1 unit (X57-605 A).
2) Upload the adjustment firmware, using “ADJUST FIRM-
WARE WRITE” menu.
3) Turn the switch (S1) OFF in TX-RX1 unit (X57-605 A).
4) Turn the transceiver ON while pressing [A=B] key to perform the full reset.
Refer to the uploading procedure
1~8.
4. Repair and adjustment
5. Uploading the user firmware
1) Turn the switch (S1) ON in TX-RX1 unit (X57-605 A).
2) Upload the user firmware, using “USER FIRMWARE
WRITE” menu.
3) Turn the switch (S1) OFF in TX-RX1 unit (X57-605 A).
4) Turn the transceiver ON while pressing [A=B] key to perform the full reset.
Refer to the uploading procedure 9.
6. Checksum confirmation
Switch the transceiver on while pressing and hold [N.R.] and [MIC/CAR] keys.
If the user firmware has not changed, the checksum is same as the value in step 1.
If the user firmware has been updated, the checksum should match the new checksum.
Refer to the uploading procedure 10.
7. Uploading the user firmware
1) Turn the transceiver ON while pressing [A=B] key to perform the full reset.
2) Run the programming software (W05-0855-00), then select
“Menu/MRch WRITE to the RADIO”
100
TS-2000/X
ADJUSTMENT
■ Procedure for writing adjustment firmware (for
both user and adjustment firmware)
1. Remove the lower case and set the slide switch (S1) of the TX-RX 1 unit (X57-605A) to ON (move the switch toward the front).
2. Connect the RS-232C port of the personal computer with the COM port of the main unit with a D-SUB (9-pin) straight cable (female-female).
3. Connect the external power supply (13.8V) to the main unit and turn the power supply ON. The main unit does not turn on any indicators, but it is ready to rewrite firmware. Do not operate the power switch on the main unit.
4. Write firmware using writing software. (See the help of the software for information on how to write it.)
5. After writing the firmware, turn the external power supply OFF and remove the RS-232C cable.
6. Set the slide switch (S1) of the TX-RX 1 unit (X57-605A) to OFF (move the switch toward the rear).
7. Turn the external power supply ON.
8. Turn the main unit ON and confirm that the indicator lights. Then, perform all reset (hold down [A=B] key and press the [POWER] key) and confirm that the initial state is displayed.
9. After adjustment, rewrite adjustment software back to user firmware using the writing software. (See the help of the software for information on how to write it.)
10. After rewriting user software, check the checksum (hold down the [N.R.] and [MIC/CAR] keys and press the
[POWER] key. Menu No.125). Then , perform all reset.
Notes :
1. When adjustment software is loaded and the main unit is turned ON, a beep sounds to indicate the adjustment mode. This does not indicate a failure.
When any key (except [PF] key) is pressed after a frequency is displayed, the beep stops.
2. Do not return the TS-2000/X that contains adjustment firmware to the user.
■ Adjustment mode operation procedure
1. Start the adjustment mode.
Hold down the [N.R.] and [MIC/CAR] keys and press the
[POWER] key. The adjustment mode is set and a menu number is displayed below the M.CH on the main band side (left) of the display.
MENU No.
2. Select adjustment mode menu No.
Turn the [MULTI CH] knob to change the menu No.
3. Change adjustment mode setting data.
Setting data can be changed with [+] or [–] key.
4. Write adjustment mode data.
Press [+] or [–] key on the main unit or [UP] or [DOWN] key on the microphone on menu No. 124.
5. Cancel adjustment mode.
Press the [CLR] key to return to the normal VFO mode.
Note:
When the power is turned OFF in the middle in the adjustment mode, it is canceled.
CN24
S1
OFF
ON
Adjustment Mode Menu (Menu No. 00~126)
27
28
29
30
23
24
25
26
31
32
19
20
21
22
15
16
17
18
11
12
13
14
07
08
09
10
03
04
05
06
No.
00
01
02
Adjustment item
ALC reference voltage
Item
14.1M
146M BPF center voltage (Main) 146M
Variable capacitor voltage 142M
Variable capacitor voltage
Variable capacitor voltage
144M
148M
Variable capacitor voltage 152M
435M BPF center voltage (Main) 440M
Variable capacitor voltage
Variable capacitor voltage
450M
430M
Variable capacitor voltage 420M
146M BPF center voltage (Sub) 146M
Variable capacitor voltage
Variable capacitor voltage
Variable capacitor voltage
Variable capacitor voltage
118M
132M
160M
174M
Frequency Mode
14.1M
USB
145.99M
USB
142.00M
USB
144.00M
USB
148.10M
USB
151.90M
USB
440.00M
USB
449.80M
USB
430.00M
USB
420.00M
USB
146.00M
FM
118.00M
FM
132.00M
FM
160.00M
FM
173.90M
FM
440M BPF center voltage (TX) 435M
Variable capacitor voltage 420M
Variable capacitor voltage
Variable capacitor voltage
440M
450M
Variable capacitor voltage (HF TX)
10.695M IF filter window
455k IF filter window
SSB IF gain
14M
10.695M
1.83M
455k
435.10M
420.10M
439.99M
449.90M
14.1M
1.83M
SSB start 14.2M
USB
USB
USB
USB
USB
USB
USB
USB
SSB S1
SSB S9
SSB S-full scale
FM S1
FM S-full scale
SSB IF gain
SSB S1
SSB S9
SSB S-full scale
FM S1
SSB S1
SSB S9
FM S1
FM full
SSB S1
SSB S9
14.2M
14.2M
SSB S full 14.2M
29.2M
29.2M
SSB start 50.2M
50.2M
50.2M
SSB S full 50.2M
FM S1 50.2M
USB
USB
USB
FM
FM
USB
USB
USB
USB
FM
101
TS-2000/X
ADJUSTMENT
76
77
78
79
72
73
74
75
68
69
70
71
64
65
66
67
80
81
82
83
84
85
60
61
62
63
56
57
58
59
52
53
54
55
48
49
50
51
44
45
46
47
40
41
42
43
36
37
38
39
No.
33
34
35
Adjustment item
FM S-full scale
SSB IF gain
SSB S1
SSB S9
SSB S-full scale
FM S1
FM full scale
FM S1 (SUB)
FM full scale (SUB)
AM S1
AM S-full scale
SSB IF gain
SSB S1
SSB S9
SSB S-full scale
FM S1
FM S-full scale
FM S1 (SUB)
FM S-full scale (SUB)
SSB IF gain
SSB S1
SSB S9
SSB S-full scale
FM S1
FM S-full scale
ALT voltage
ALT voltage
SQ threshold voltage
SQ threshold voltage
SQ tight voltage (144M)
SQ threshold voltage (144M)
Item
FM full
Frequency Mode
50.2M
FM
SSB start 144.2M
USB
SSB S1 144.2M
USB
SSB S9 144.2M
USB
SSB S full 144.2M
USB
FM S1
FM full
145.8M
145.8M
FM
FM
FM S1
FM full
AM S1
AM full
145.8M
145.8M
FM
FM
120.2M
AM
120.2M
AM
SSB start 438.2M
USB
SSB S1 438.2M
USB
SSB S9 438.2M
USB
SSB S full 438.2M
USB
FM S1
FM full
FM S1
FM full
438.2M
438.2M
438.2M
438.2M
FM
FM
FM
FM
SSB start 1270.2M
USB
SSB S1 1270.2M
USB
SSB S9 1270.2M
USB
SSB S full 1270.2M
USB
FM S1 1270.2M
FM
FM full 1270.2M
FM
Center 1270.2M
FM
Center 145.8M
FM
FM
FM
FM
FM
50.2M
145.8M
145.8M
145.8M
FM
FM
FM
FM
SQ tight voltage (144M)
SQ threshold voltage (430M)
SQ threshold voltage (430M)
SQ threshold voltage (1200MHz)
FM
FM
FM
FM
145.8M
438.2M
FM
FM
438.2M
FM
1270.2M
FM
Power (POC)/Power meter 100W/20W 14.1M
Power (POC)/Power meter 50W/10W 14.1M
Power (POC)/Power meter 25W/5W 14.1M
Power (POC)/Power meter 10W/2W 14.1M
USB
USB
USB
USB
Power (POC)/Power meter 5W/1W
TX gain for band 1.8M
TX gain for band
TX gain for band
3.5M
7M
TX gain for band
TX gain for band
TX gain for band
TX gain for band
10M
14M
18M
21M
14.1M
1.83M
3.51M
7.01M
10.1M
14.1M
18.1M
21.1M
USB
USB
USB
USB
USB
USB
USB
USB
TX gain for band
TX gain for band
TX gain for band
HF TX gain for power
HF TX gain for power
HF TX gain for power
24M
28M
24.9M
28.1M
52M 50.1M
50W/10W 14.1M
25W/5W 14.1M
10W/2W 14.1M
USB
USB
USB
USB
USB
USB
89
90
91
92
No.
86
87
88
Adjustment item
HF TX gain for power
ALC meter start
ALC meter zone max
Item
5W/1W
Frequency Mode
14.1M
USB
Start 14.1M
Zone max 14.1M
USB
USB
FM modulation deviation Wide dev 29.1M
FM modulation deviation Narrow dev 29.1M
FM
FM
Power (POC) / Power meter 100W/20W 145.9M
USB
Power (POC) / Power meter 50W/10W 145.9M
USB
93
94
95
96
Power (POC) / Power meter 25W/5W 145.9M
USB
Power (POC) / Power meter 10W/2W 145.9M
USB
Power (POC) / Power meter 5W/1W 145.9M
USB
TX gain for band 146M 145.9M
USB
97
98
144M TX gain for power
144M TX gain for power
99 144M TX gain for power
100 144M TX gain for power
50W/10W
25W/5W
10W/2W
5W/1W
145.9M
145.9M
145.9M
145.9M
USB
USB
USB
USB
101 Power (POC) / Power meter 50W/20W 438.1M
USB
102 Power (POC) / Power meter 25W/10W 438.1M
USB
103 Power (POC) / Power meter 12.5W/5W 438.1M
USB
104 Power (POC) / Power meter 5W/1W 438.1M
USB
105 TX gain for band
106 440M TX gain for power
107 440M TX gain for power
108 440M TX gain for power
440M
25W/10W
12.5W/5W
5W/1W
438.1M
438.1M
438.1M
438.1M
USB
USB
USB
USB
109 Power (POC) / Power meter
110 Power (POC) / Power meter
10W
5W
111 Power (POC) / Power meter 2.5W
112 Power (POC) / Power meter 1W
113 TX gain for 1.2G band
114 TX gain for band
115 TX gain for 1.2G band
116 1.2G TX gain for power
1.2G
1.2G
1.2G
2.5W
1270.1M
1270.1M
1270.1M
1270.1M
1240.1M
1270.1M
1299.9M
1270.1M
USB
USB
USB
USB
USB
USB
USB
USB
117
118
119
120
121
122
123
1.2G TX gain for power
SWR protection
SWR meter (VSWR : 3.0)
SWR meter (VSWR : 3.0)
SWR protection
SWR protection
SWR protection
124 EEPROM write
125 Checksum
126 Display check / Activate all the AT relay contacts
1W
HF
14M
52M
1270.1M
USB
14.1M
CW
14.1M
50.1M
FM
CW
146M
440M
145.9M
438.1M
CW
CW
1270.1
1270.1M
CW
You can confirm the settings of Menu No. 125 and 126 even if you are not in the adjustment mode.
■ Menu No. 125 checksum display
Main CPU DSP1 DSP2
102
TS-2000/X
ADJUSTMENT
Display Check
Item
1. All reset
Condition
1) DC IN : 13.8V
Hold down [A=B] key and press the [POWER]key.
Measurement
Testequipment
Unit Terminal
Adjustment
Specifications/Remarks
Unit Parts Method
Front LCD After displaying panel “HELLO”, the
Display should be normal.
Should be at the reset display is reset as frequency.
follows;
Main band side
DISP f. : 14.000.00
Mode : USB
ANT1, PTT, CTRL,
AGC, PRE
Sub band side
DISP f. : 144.000.00
Mode : FM
PRE, TNC
Check LCD all segments light.
2. LCD all segments light
1) Menu No. : 126
PLL Section
Item Condition
1. 31.2MHz
level
1) Display f. : 14.100MHz
Mode : USB
Receive
2. Lock voltage 1) HF REF VCO
Display f. : 2.000MHz
Mode : FM
Display f. : 12.990MHz
2) HF1 MAIN PLL
Display f. : 30.00kHz
Mode : FM
Display f. : 16.990MHz
3) HF2 MAIN PLL
Display f. : 17.00MHz
Mode : FM
Display f. : 36.990MHz
4) HF3 MAIN PLL
Displat f. : 37.00MHz
Mode : FM
Display f. : 60.000MHz
5) HF LO2 PLL
Display f. : 24.00MHz
Mode : FM
Display f. : 29.000MHz
6) VHF REF PLL
Display f. : 142.00MHz
Mode : FM
Display f. : 151.990MHz
Measurement
Testequipment
Unit Terminal Unit
Adjustment
Parts Method
Oscilloscope TX-RX2 W503 TX-RX2 L422 Level max.
(B/11) (B/11) L427
DC V.M
Spectrum analyzer
TP501 TX-RX2 TC403 1.5V
(D/11)
Check
TP502 TX-RX2 TC408 1.45V
(J/11)
Check
TX-RX2 TC410 1.45V
(J/11)
Check
TX-RX2 TC409 1.45V
(J/11)
Check
TX-RX2 TP505 TX-RX2 TC402 1.5V
(C/11) (I/11)
Check
TX-RX2 TP512 TX-RX2 TC406 2.0V
(B/11) (E/11)
Check
Specifications/Remarks
–3dBm or more
±
0.5V
4.6V or less
±
0.05V
6.3V or less
±
0.05V
6.3V or less
±
0.05V
6.3V or less
±
0.05V
4.6V or less
±
0.5V
4.6V or less
103
TS-2000/X
ADJUSTMENT
Item Condition
7) VHF MAIN PLL
Display f. : 142.00MHz
Mode : FM
Display f. : 152.000MHz
8) UHF PLL
Display f. : 449.990MHz
Mode : FM
Display f. : 420.000MHz
9) SUB1 PLL
Display f. : 154.495MHz
Mode : FM
Display f. : 220.000MHz
10) SUB2 PLL
Display f. : 173.995MHz
Mode : FM
Display f. : 135.000MHz
Measurement
Testequipment
Unit Terminal Unit
Adjustment
Parts
DC V.M
TX-RX2 TP503 TX-RX2 TC405 1.0V
Spectrum (B/11) (H/11) analyzer
Check
Method
TP504 TX-RX2 TC404 6.0V
(G/11)
Check
TX-RX2 TP506 TX-RX2 TC400 5.5V
(C/11) (K/11)
Check
TX-RX2 TC401 5.5V
(K/11)
Check
Specifications/Remarks
±
0.03V
4.6V or less
±
0.05V
1.5V or more
±
0.2V
1.0V or less
±
0.5V
1.0V or less
Receiver Section
Item
1. HF BPF
Condition
1) Display f. : 7.200MHz
Mode : AM
Spectrum analyzer setting
Center f. : 7.000MHz
Frequency span : 5MHz
XdB/DIV : 10dB
RBW : 30kHz
VBW : 30kHz
2) Display f. : 14.200MHz
Spectrum analyzer setting
Center f. : 14.000MHz
3) Display f. : 50.000MHz
Spectrum analyzer setting
Center f. : 54.000MHz
2. RX trap
(E type only)
1) Display f. : 11.700MHz
Mode : AM
PRE-AMP : ON
2) Display f. : 15.501MHz
Measurement
Testequipment
Unit Terminal
Tracking Rear ANT1 generator panel
Unit Parts
TX-RX1 L23
(A/9) L24
L25
Adjustment
Method
Adjust the coils to obtain the frequency response as shown.
Spectrum TX-RX1 CN5 analyzer (A/9)
Specifications/Remarks
7.000
(MHz)
L32
L33
L34
L45
L46
L44
TC1
TC2
Adjust the coil to get a null point at
68.985MHz as shown.
Adjust the trimmer to get a null point at
11.7MHz.
Adjust the trimmer to get a null point at
15.501MHz.
14.000
(MHz)
54.000
(MHz)
68.985
104
TS-2000/X
ADJUSTMENT
Item Condition
3. MCF 1) Display f. : 14.000MHz
(69.085MHz) Mode : USB
PRE-AMP : ON
AGC : OFF
Spectrum analyzer setting
Center f. : 69.085MHz
Frequency span : 100kHz
XdB/DIV : 10dB
RBW : 30kHz
VBW : 30kHz
4. MCF 1) Display f. : 18.000MHz
(72.925MHz) Spectrum analyzer setting
Center f. : 72.925MHz
Measurement
Testequipment
Unit Terminal
Tracking Rear ANT1 generator panel
Spectrum analyzer
TX-RX1 TP4
(A/9) (CN6)
TP5
(CN9)
Unit Parts
TX-RX1 L54
(A/9) L62
L63
L64
L68
Adjustment
Method
Adjust the coils to obtain the frequency response as shown.
L65
L66
L67
Specifications/Remarks
69.085
(MHz)
72.925
(MHz)
• Perform the following in the adjustment mode. Item 5, 6, 10~12, 16, 17 and 21~38.
To terminate the adjustment menu in the middle, save your settings with Menu No. 124.
5. MAIN
VHF BPF
1) Sub band f. : 144.000MHz
Mode : USB
PRE-AMP : ON
AGC : ON
Spectrum analyzer setting
Center f. : 146.000MHz
Frequency span : 50MHz
XdB/DIV : 5dB
RBW : 100kHz
VBW : 30kHz
Tracking generator
Rear panel
ANT144 TX-RX2 L163
Spectrum TX-RX2 CN19 analyzer (A/11)
(A/11) L164
Adjust the coils to obtain the frequency response as shown.
2) Menu No. : 01
Display f. : 146MHz
CN15
3) Menu No. : 02
Display f. : 142MHz
Front [+] key After setting the panel or adjustment value to
[–] key 160, adjust each coil
TX-RX2 L23 to obtain the fre-
(A/11) L34
L47
L55 quency response as shown.
Front [+] key Change the adjustpanel or ment values to get
[–] key the highest peak points as shown.
142
146 152
(MHz)
146MHz
142MHz
4) Menu No. : 03
Display f. : 144MHz
144MHz
5) Menu No. : 04
Display f. : 148MHz
148MHz
6) Menu No. : 05
Display f. : 152MHz
152MHz
105
TS-2000/X
ADJUSTMENT
Item
6. MAIN
UHF BPF
Condition
1) Trap default
2) Menu No. : 06
Display f. : 440MHz
Spectrum analyzer setting
Center f. : 440.000MHz
Frequency span : 100MHz
XdB/DIV : 5dB
RBW : 100kHz
VBW : 30kHz
Measurement
Testequipment
Unit Terminal Unit Parts
Tracking Rear ANT430 TX-RX2 TC9 generator panel (A/11)
Adjustment
Method
Adjust the trimmer to get a null point at
366MHz as shown.
Spectrum TX-RX2 CN19 analyzer (A/11)
Front [+] key After setting the panel or adjustment value to
[–] key 145, adjust each
TX-RX2 TC1 trimmer to obtain
(A/11) TC2
TC3 the frequency response as shown.
3) Menu No. : 07
Display f. : 449.8MHz
Front [+] key Change the adjustpanel or ment values to get
[–] key the highest peak points as shown.
Specifications/Remarks
366MHz
440MHz
449.8MHz
4) Menu No. : 08
Display f. : 430MHz
430MHz
5) Menu No. : 09
Display f. : 420MHz
7. HF RX
IF gain
8. 1st mixer balance
1) Display f. : 14.201MHz
Mode : USB
PRE-AMP : OFF
AF output : 0.63V/8
Ω
SSG f. : 14.201MHz
SSG output : –113dBm/0.501
µ
V
SSG
Oscilloscope
AF V.M
DM. SP
Rear ANT1 panel
EXT. SP
TX-RX1 L69
(A/9) L71
L613
L614
L87
1) Display f. : 100kHz
Mode : USB
PRE-AMP : OFF
SSG output : OFF
VR1
AF output max.
Noise min.
9. Gain balance 1) Display f. : 9.000MHz
Mode : USB
SSG f. : 9.001MHz
SSG output : –116dBm/0.35
µ
V
VR4 Set the AF output voltage to 0.63V at
8,999.99kHz. Then adjust VR4 to obtain the voltage 0.63V at
9.000MHz when the transceiver is in the receive mode.
(If you would not get the specified voltage, adjust
3. MCF and
4. MCF again.)
106
420MHz
TS-2000/X
ADJUSTMENT
Item Condition
Measurement
Testequipment
Unit Terminal
10. 10.695MHz 1) Menu No. : 20
IF filter SSG1 f. : 1.8330MHz
SSG1
SSG2
SSG1 output : –33dBm/5010
µ
V 2 signal pad
Rear pnel
ANT2
SSG2 f. : 1.8301MHz
SSG2 output : –33dBm/5010
µ
V Oscilloscope TX-RX1 TP1
Disconnect the cable from (A/9)
CN23.
2 signal pad
SSG1
ANT
SSG2
Unit
Adjustment
Parts Method
Front [+] key Change the adjustpanel or ment values to get
[–] key the waveform as shown.
Specifications/Remarks
11. 455kHz
IF filter
1) Menu No. : 21
Connect the cable to CN23.
TP2
12. SSB IF gain 1) Menu No. : 22
(AGC start Display f. : 14.201MHz
level) Mode : USB
SSG output : –110dBm/0.707
µ
V
SSG
2) Menu No. : 28
Display f. : 50.201MHz
SSG outut : –114dBm/0.446
µ
V
13. NB gain
ANT1
1) Display f. : 14.200MHz
Mode : USB
PRE-AMP : ON SSG
SSG f. : 14.200MHz
SSG output : –103dBm/1.58
µ
V AF V.M
AGC : ON Oscilloscope
NB : ON
2) NB : OFF
→
ON
DC V.M
TX-RX1 TPNB
(A/9)
Rear ANT1 panel
EXT. SP
DM. SP
Noise G.
TX-RX1 L81
(A/9) L82
Change the adjustment values within the range of 1 to 5 on the display.
Voltage min.
Adjust output of Noise should disappear noise generator to when NB is on.
S1 and S9, and check each.
AF distortion min.
3% or less 14. FM 1) Display f. : 29.2MHz
discriminator Mode : FM coil (HF) AF output : 0.63V/8
Ω
SSG f. : 29.2MHz
SSG output : –53dBm/501
µ
V
MOD : 1kHz
DEV : 3kHz
TX-RX1 L83
(A/9)
15. RX IF gain 1) Display f. : 145.991MHz
(VHF) Mode : USB
AF output : 0.63V/8
Ω
SSG
Oscilloscope
SSG f. :145.991MHz
AF V.M
SSG output : –120dBm/0.22
µ
V DM. SP
Rear ANT144 TX-RX2 L80 panel (A/11) L82
EXT. SP L86
16. SSB IF gain 1) Menu No. : 34
(AGC start level)
Display f. : 144.201MHz
Mode : USB
SSG output : –116dBm/0.35
µ
V
2) Menu No. : 44
Display f. : 438.20MHz
SSG output : –116dBm/0.35
µ
V
ANT430
AF output max.
Front [+] key Change the adjustpanel or ment values within
[–] key the range of 1 to 5 on the display.
107
TS-2000/X
ADJUSTMENT
Item Condition
Measurement
Testequipment
Unit Terminal Unit Parts
17. Sub band
BPF
1) Menu No. : 10
Display f. : 146MHz
SSG Rear ANT144 TX-RX2 L28 panel (A/11) L44
L52 Mode : FM Oscilloscope
SSG output : –110dBm/0.707
µ
V AF V.M
MOD : 1kHz
EXT. SP
DM. SP TX-RX2 SSM
DEV : 3kHz (A/11)
Adjustment
Method
After setting the adjustment value to
90, adjust each coil to obtain the specified values.
Specifications/Remarks
S-meter voltage max.
2) Menu No. : 11
Display f. : 118MHz
Mode : FM
MOD : 1kHz
DEV : 3kHz
3) Menu No. : 12
Display f. : 132MHz
Mode : FM
MOD : 1kHz
DEV : 3kHz
Front [+] key Change the adjust(1.04V) panel or ment values to have
[–] key the highest readings of S-meter voltage.
(1.13V)
(1.17V) 4) Menu No. : 13
Display f. : 160MHz
Mode : FM
MOD : 1kHz
DEV : 3kHz
5) Menu No. : 14
Display f. : 174MHz
Mode : FM
MOD : 1kHz
DEV : 3kHz
18. FM 1) Display f. : 145.800MHz
discriminator Mode : FM coil AF output : 0.63V/8
Ω
(VHF)
Sub band
SSG f. : 145.800MHz
SSG output : –53dBm/501
µ
V AF V.M
MOD : 3kHz
DC V.M
TX-RX2 CN1
(A/11)
SSG
Oscilloscope
Rear panel
ANT144
EXT. SP
DM. SP
19. Trap frequency
(UHF)
1) SSG1 f. : 439.8MHz
Mode : FM
SSG1 output : –108dBm/0.9
µ
V
MOD : 1kHz
DEV : 3kHz
SSG2 f. : 356.01MHz
TX-RX2 L93
(A/11)
ANT430 TX-RX TC9
(A/11)
Mode : FM
SSG2 output : –30dBm/7070
µ
V
MOD : 400Hz
DEV : 3kHz
20. S/N check 1) Display f. : Next page
(Reference) AF output : 0.63V/8
Ω
AGC : FAST
SSG f. : Next page
However, USB : +1kHz
PRE-AMP : ON
ATT : OFF
SSG
AF V.M
Oscilloscope
Distortion meter
DM. SP
Rear ANT panel
EXT. SP
AF output max.
Check the AF distortion
SINAD max.
(1.11V)
3% or less
108
TS-2000/X
ADJUSTMENT
Item Condition
Measurement
Testequipment
Unit Terminal
Adjustment
Unit Parts Method
Specifications/Remarks
SUB
MAIN
MAIN
MAIN
SUB
SUB
SUB
Band
MAIN
MAIN
MAIN
MAIN
MAIN
MAIN
SUB
Frequency (K) Frequency (E) Mode SSG RF level (dBm) SSG MOD
550kHz 550KHz AM –85
DEV
1kHz 60%
→
OFF
14.200MHz
18.200MHz
14.200MHz
18.200MHz
USB
USB
–119
→
OFF
–119
→
OFF
OFF
OFF
OFF
OFF
52.200MHz
52.200MHz
146.200MHz
145.200MHz
FM
AM
–118
–106
1kHz 3kHz
1kHz 60%
→
OFF
Measurement Spec.
S/N
S/N
S/N
SINAD
S/N
>10dB
>10dB
>10dB
>12dB
>10dB
146.200MHz
145.200MHz
FM –121 SINAD >12dB
118.200MHz
146.200MHz
–
145.200MHz
AM
FM
–85
–117
1kHz 3kHz
1kHz 60%
→
OFF
1kHz 3kHz
S/N
SINAD
>10dB
>12dB
440.200MHz
435.200MHz
FM
430.200MHz
430.200MHz
FM
–122
–121
1kHz
1kHz
3kHz
3kHz
SINAD
SINAD
>12dB
>12dB
449.200MHz
439.200MHz
FM
444.200MHz
430.200MHz
FM
438.200MHz
435.200MHz
FM
449.200MHz
439.200MHz
FM
–121
–117
–117
–117
1kHz
1kHz
1kHz
1kHz
3kHz
3kHz
3kHz
3kHz
SINAD
SINAD
SINAD
SINAD
>12dB
>12dB
>12dB
>12dB
21. SSB
S-meter
S1 (HF)
S9
1) Menu No. : 23
Display f. : 14.201MHz
Mode : USB
AGC : ON
PRE-AMP : ON
SQL : Counterclockwise max.
(Level min.)
RF GAIN : Clockwise max.
SSG f. : 14.201MHz
SSG output : –107dBm/1
µ
V
SSG
AF V.M
Oscilloscope
DM. SP
Rear ANT1 panel
EXT. SP
Front [+] key 1 push panel or
[–] key
2) Menu No. : 24
SSG output : –81dBm/19.9
µ
V
Full scale
(Lights up all)
3) Menu No. : 25
SSG output : –21dBm/19900
µ
V
22. FM
S-meter
S1 (HF)
1) Menu No. : 26
Display f. : 29.2MHz
Mode : FM
SSG f. : 29.2MHz
SSG output : –117dBm/0.316
µ
V
MOD : 1kHz
DEV : 3kHz
Full scale
(Lights up all)
2) Menu No. : 27
SSG output : –95dBm/3.98
µ
V
23. 50MHz 1) Menu No. : 29
SSB S-meter Display f. : 50.2MHz
S1 Mode : USB
SSG output : –111dBm/0.63
µ
V
S9 2) Menu No. : 30
SSG output : –85dBm/12.6
µ
V
Full scale
(Lights up all)
3) Menu No. : 31
SSG output : –25dBm/12600
µ
V
S-meter lights up to S1 level.
S-meter lights up to S9 level.
S-meter lights up all.
S-meter lights up to S1 level.
S-meter lights up all.
S-meter lights up to S1 level.
S-meter lights up to S9 level.
S-meter lights up all.
109
TS-2000/X
ADJUSTMENT
Item Condition
Measurement
Testequipment
Unit Terminal
24. 50MHz FM 1) Menu No. : 32
S-meter Display f. : 50.2MHz
S1
SSG
Mode : FM AF V.M
SSG output : –117dBm/0.316
µ
V Oscilloscope
MOD : 1kHz DM. SP
DEV : 3kHz
Rear ANT1 panel
EXT. SP
Unit
Adjustment
Parts Method
Front [+] key 1 push panel or
[–] key
Full scale
(Lights up all)
2) Menu No. : 33
SSG output : –95dBm/3.98
µ
V
25. 144MHz 1) Menu No. : 35
SSB S-meter Display f. : 144.2MHz
S1 Mode : USB
SSG output : –113dBm/0.501
µ
V
S9 2) Menu No. : 36
SSG output : –93dBm/5.01
µ
V
Full scale
(Lights up all)
3) Menu No. : 37
SSG output : –43dBm/1580
µ
V
26. 144MHz
FM S-meter
S1
1) Menu No. : 38
Display f. : 145.8MHz
Mode : FM
SSG output : –117dBm/0.316
µ
V
MOD : 1kHz
DEV : 3kHz
ANT144
Full scale
(Lights up all)
2) Menu No. : 39
SSG output : –95dBm/3.98
µ
V
27. 120MHz
SUB AM
S-mete
S1
1) Menu No. : 42
Display f. : 120.2MHz
Mode : AM
SSG output : –105dBm/1.26
µ
V
MOD : 1kHz
DEV : 60%
Full scale
(Lights up all)
2) Menu No. : 43
SSG output : –85dBm/12.6
µ
V
28. 144MHz
SUB FM
S-mete
S1
1) Menu No. : 40
Display f. : 145.8MHz
Mode : FM
SSG output : –117dBm/0.316
µ
V
MOD : 1kHz
DEV : 3kHz
Full scale
(Lights up all)
2) Menu No. : 41
SSG output : –95dBm/3.98
µ
V
29. 440MHz 1) Menu No. : 45
SSB S-meter Display f. : 438.2MHz
S1 Mode : USB
SSG output : –113dBm/0.501
µ
V
S9 2) Menu No. : 46
SSG output : –93dBm/5.01
µ
V
Full scale
(Lights up all)
3) Menu No. : 47
SSG output : –43dBm/1580
µ
V
ANT430
110
Specifications/Remarks
S-meter lights up to S1 level.
S-meter lights up all.
S-meter lights up to S1 level.
S-meter lights up to S9 level.
S-meter lights up all.
S-meter lights up to S1 level.
S-meter lights up all.
S-meter lights up to S1 level.
S-meter lights up all.
S-meter lights up to S1 level.
S-meter lights up all.
S-meter lights up to S1 level.
S-meter lights up to S9 level.
S-meter lights up all.
ADJUSTMENT
Item
30. 440MHz
FM S-meter
S1
Condition
Measurement
Testequipment
Unit Terminal
1) Menu No. : 48
Display f. : 438.2MHz
SSG
Mode : FM AF V.M
SSG output : –117dBm/0.316
µ
V Oscilloscope
MOD : 1kHz DM. SP
DEV : 3kHz
Unit
Adjustment
Parts Method
Rear ANT430 Front [+] key 1 push panel panel or
EXT. SP [–] key
Full scale
(Lights up all)
2) Menu No. : 49
SSG output : –95dBm/3.98
µ
V
31. 440MHz
SUB FM
S-mete
S1
1) Menu No. : 50
Display f. : 438.2MHz
Mode : FM
SSG output : –117dBm/0.316
µ
V
MOD : 1kHz
DEV : 3kHz
Full scale
(Lights up all)
2) Menu No. : 51
SSG output : –95dBm/3.98
µ
V
32. 144MHz
FM SQL threshold
1) Menu No. : 61
Display f. : 145.8MHz
Mode : FM
SSG output : OFF
MOD : 1kHz
DEV : 3kHz
33. 144MHz
FM SQL tight
34. 144MHz sub band
FM SQL threshold
35. 144MHz sub band
FM SQL tight
1) Menu No. : 62
Display f. : 145.8MHz
Mode : FM
SSG output : –113dBm/0.501
µ
V
MOD : 1kHz
DEV : 3kHz
1) Menu No. : 63
Display f. : 145.8MHz
Mode : FM
SSG output : OFF
MOD : 1kHz
DEV : 3kHz
1) Menu No. : 64
Display f. : 145.8MHz
Mode : FM
SSG output : –113dBm/0.501
µ
V
MOD : 1kHz
DEV : 3kHz
36. 50MHz
FM SQL threshold
37. 430MHz
FM SQL threshold
1) Menu No. : 60
Display f. : 50.2MHz
Mode : FM
SSG output : OFF
MOD : 1kHz
DEV : 3kHz
1) Menu No. : 66
Display f. : 438.2MHz
Mode : FM
SSG output : OFF
MOD : 1kHz
DEV : 3kHz
ANT144
ANT1
ANT430
TS-2000/X
Specifications/Remarks
S-meter lights up to S1 level.
S-meter lights up all.
S-meter lights up to S1 level.
S-meter lights up all.
111
TS-2000/X
ADJUSTMENT
Item Condition
SSG
Measurement
Testequipment
Unit Terminal
AF V.M
Oscilloscope
DM. SP
Unit
Adjustment
Parts
38. 430MHz sub band
FM SQL threshold
1) Menu No. : 65
Display f. : 438.2MHz
Mode : FM
SSG output : OFF
MOD : 1kHz
DEV : 3kHz
• Writing data : After items 5, 6, 10~12, 16, 17 and 21~38 have been adjusted;
1) Menu No. 124
2) [+] or [–] key : Push once time. Display “rEAdy”
→
“good” (If “nG” is displayed, enter data again.)
3) [CLR] key : Push once time.
Method
Rear ANT430 Front [+] key 1 push panel panel or
EXT. SP [–] key
Specifications/Remarks
Transmitter Section
Item
1. Final idling 1) Display f. : 14.100MHz
current
(HF/VHF)
Mode : USB
Final unit (A/2)
VR1, 2 : MIN
Transmit
Condition
DC. A
Measurement
Testequipment
Unit
Rear panel
Terminal
DC
Unit
Final
(A/2)
Adjustment
Parts Method
Check the default current (Io).
VR1
VR2 I
Io + 700mA = I
A
+ 500mA
VR102 Io + 1000mA
A
2. 29.1MHz
frequency
3. Final idling 1) Display f. : 430MHz current
(UHF)
2) Display f. : 145.900MHz
Mode : USB
VR102 : MIN
Transmit
1) Display f. : 29.100MHz
Mode : FM
Transmit
Mode : USB
Final unit (B/2)
VR901, 902 : MIN
Transmit f. counter
DC. A
TX-RX1 CN14
(A/9)
Rear panel
DC
TX-RX1 TC3
(A/9)
Final
(B/2)
29.10000MHz
Check the default current (Io).
VR901 Io + 300mA = Ic
VR902 Ic + 300mA
4. TX BPF
(VHF)
1) Display f. : 144.9MHz
Mode : CW
Disconnect the cable from
CN4 and insert a cable from the spectrum analyzer.
Transmit
After the adjustment, connect the cable to CN4.
Spectrum TX-RX2 CN4 analyzer (A/11)
TX-RX2 TC12
(A/11)
• Perform the following in the adjustment mode. Item 5~8 and 12~28.
To terminate the adjustment menu in the middle, save your settings with Menu No. 124.
TC13
IF output max.
TC14 229MHz spurious level min.
Specifications/Remarks
±
20mA
±
10Hz
±
20mA
112
TS-2000/X
ADJUSTMENT
Item
5. TX BPF
(UHF)
.
Condition
1) Menu No. : 15
Display f. : 435.1MHz
Mode : USB
Disconnect the cable from
CN3 and insert a cable from the spectrum analyzer.
Transmit
Measurement
Testequipment
Unit Terminal
Spectrum TX-RX2 CN3 analyzer (A/11)
Unit
Adjustment
Parts Method
Front [+] key After setting the panel or adjustment value to
[–] key 131, adjust the
TX-RX2 L90 trimmers and coils
(A/11) L91
TC4
TC5
TC6 to have a maximum
IF output.
TC8
TC10
Specifications/Remarks
8dBm or more
2) Menu No. : 16
Display f. : 420.1MHz
(K type only) 3) Menu No. : 17
Display f. : 439.99MHz
Front [+] key Output gain max.
panel or
[–] key
6. ALC reference voltage
7. TX IF gain
(HF)
8. TX IF BPF
(HF)
4) Menu No. : 18
Display f. : 449.9MHz
After the adjustment, connect the cable to CN3.
1) Menu No. : 00
Display f. : 14.1MHz
Mode : USB
Transmit
1) Menu No. : 78
Display f. : 18.1MHz
Mode : USB
Transmit
1) Menu No. : 19
Display f. : 14.1MHz
Mode : USB
Transmit
DC V.M
50
Ω
dummy
Oscilloscope
Spectrum analyzer
TX-RX1 TP3
(A/9)
CN14
Front [+] key Set the adjustment 2.7V
±
0.05V
panel or value within the
[–] key limit of the specified voltage.
TX-RX1 L109 Drive output level
(A/9) L108 max.
L105
L103
L102
L100
L99
L98
L96
–4dBm or more
Front [+] key Change the adjust3dBm or more panel or ment values to get
[–] key the peak reading to
TX-RX1 L100 a maximum output.
(A/9) L99
L98
L96
L102
VR3
TX-RX1 VR2
(A/9)
68.985MHz
spurious level min.
9. TX mixer balance
10. Maximum 1) Display f. : 438.110MHz
power Mode : CW
UHF Transmit
VHF 2) Display f. : 145.9MHz
Mode : CW
Transmit
11. Null
1) Display f. : 50.1MHz
Mode : CW
Transmit
1) Display f. : 14.1MHz
Mode : CW
Transmit
Power meter Rear
DC V.M
panel
Power meter Rear panel
Final
Oscilloscope (A/2)
ANT430 Final
(B/2)
ANT144 Final
ANT1
CN11
(A/2)
Filter
TC901 Power output max.
TC101
TC102
TC1 VSR voltage min.
63W or more
100W or more
0.3V or less
113
TS-2000/X
Item Condition
12. Power frequency
1) Menu No. : 68
Display f. : 14.1MHz
characteristic Mode : USB
(HF) Transmit
2) Menu No. : 120
Display f. : 51.99MHz
Transmit
3) Menu No. : 68
Display f. : 14.1MHz
Transmit
13. HF power 1) Menu No. : 68
POC Display f. : 14.1MHz
(100W/20W) Mode : USB
SQL : MIN
RF GAIN : MAX
Transmit
(50W/10W) 2) Menu No. : 69
Transmit
(25W/5W) 3) Menu No. : 70
Transmit
(10W/2W) 4) Menu No. : 71
Transmit
(5W/1W) 5) Menu No. : 72
Transmit
14. Band TGC 1) Menu No. : 73
1.8MHz
Display f. : 1.83MHz
Mode : USB
Transmit
3.5MHz
2) Menu No. : 74
Display f. : 3.51MHz
Transmit
7.0MHz
10MHz
3) Menu No. : 75
Display f. : 7.01MHz
Transmit
4) Menu No. : 76
Display f. : 10.1MHz
Transmit
14MHz
18MHz
21MHz
5) Menu No. : 77
Display f. : 14.1MHz
Transmit
6) Menu No. : 78
Display f. : 18.1MHz
Transmit
7) Menu No. : 79
Display f. : 21.1MHz
Transmit
114
ADJUSTMENT
Measurement
Testequipment
Unit Terminal
Power meter Rear ANT1 panel
DC V.M
Final CN11
Oscilloscope (A/2)
Unit Parts
Filter VR1
Adjustment
Method
Set it at the center position.
Specifications/Remarks
Front [+] key Set the adjustment 100W
±
3W panel or value within the
[–] key limit of the specified power.
Filter VR1 100W
±
3W
Check 100W
±
5W
Power meter Rear ANT1 panel
Front [+] key Set the adjustment 100W
±
3W panel or value within the
[–] key limit of the specified power.
50W
±
2W
25W
±
1W
10W
±
0.5W
5W
±
0.3W
100W
±
3W
Item Condition
24MHz
28MHz
8) Menu No. : 80
Display f. : 24.9MHz
Transmit
9) Menu No. : 81
Display f. : 28.1MHz
Transmit
52MHz
15. Power PGC 1) Menu No. : 83
50W/10W Display f. : 14.1MHz
Mode : USB
Transmit
25W/5W
10) Menu No. : 82
Display f. : 50.1MHz
Transmit
10W/2W
2) Menu No. : 84
Transmit
3) Menu No. : 85
Transmit
5W/1W 4) Menu No. : 86
Transmit
16. VHF power 1) Menu No. : 91
POC Display f. :145.9MHz
100W/20W Mode : USB
Transmit
50W/10W 2) Menu No. : 92
Transmit
25W/5W 3) Menu No. : 93
Transmit
10W/2W
5W/1W
4) Menu No. : 94
Transmit
5) Menu No. : 95
Transmit
17. VHF band 1) Menu No. : 96
TGC Display f. : 145.9MHz
Mode : USB
Transmit
18. VHF power PGC
50W/10W
1) Menu No. : 97
Display f. : 145.9MHz
Mode : USB
Transmit
25W/5W
10W/2W
2) Menu No. : 98
Transmit
3) Menu No. : 99
Transmit
5W/1W 4) Menu No. : 100
Transmit
TS-2000/X
ADJUSTMENT
Measurement
Testequipment
Unit Terminal
Power meter Rear ANT1 panel
Adjustment
Specifications/Remarks
Unit Parts Method
Front [+] key Set the adjustment 100W
±
3W panel or value within the
[–] key limit of the specified power.
ANT144
50W
±
2W
25W
±
1W
10W
±
0.5W
5W
±
0.3W
100W
±
3W
50W
±
2W
25W
±
1W
10W
±
0.5W
5W
±
0.3W
100W
±
3W
50W
±
2W
25W
±
1W
10W
±
0.5W
5W
±
0.3W
115
TS-2000/X
ADJUSTMENT
Item Condition
19. UHF power POC
50W/20W
1) Menu No. : 101
Display f. : 438.1MHz
Mode : USB
Transmit
25W/10W 2) Menu No. : 102
Transmit
12.5W/5W 3) Menu No. : 103
Transmit
5W/1W 4) Menu No. : 104
Transmit
20. UHF band 1) Menu No. : 105
TGC Display f. : 438.1MHz
Mode : USB
Transmit
21. UHF power PGC
25W/10W
1) Menu No. : 106
Display f. : 438.1MHz
Mode : USB
Transmit
Measurement
Testequipment
Unit
Power meter Rear panel
Terminal
ANT430 Front
12.5W/5W 2) Menu No. : 107
Transmit
5W/1W 3) Menu No. : 108
Transmit
22. ALC meter 1) Menu No. : 87 start point Display f. : 14.1MHz
Mode : USB
Transmit
Zone max.
2) Menu No. : 88
Transmit
23. FM DEV
Wide
Narrow
1) Menu No. : 89
Display f. : 29.1MHz
Mode : FM
Transmit
2) Menu No. : 90
Transmit
ANT1
24. HF SWR protection
1) Menu No. : 118
Display f. : 14.1MHz
Mode : CW
Transmit
150
Ω
dummy connection
: Use a cable that is 1m long
Through type Rear ANT2 power meter panel
150
Ω
dummy
25. SWR meter 1) Menu No. : 119
(SWR : 3) Display f. : 14.1MHz
Mode : FM
Transmit
150
Ω
dummy connection
: Use a cable that is approx. 10cm long
26. 50MHz
SWR meter
(SWR : 3)
1) Menu No. : 120
Display f. : 50.1MHz
Mode : CW
Transmit
Unit
panel
Adjustment
Parts Method
[+] key Set the adjustment or value within the
[–] key limit of the specified power.
[+] key 1 push
[+] key Set the adjustment or value within the
[–] key limit of the specified power.
[+] key 1 push
Specifications/Remarks
50W 2W
25W
±
1W
12.5W
5W
12.5W
5W
±
50W
25W
±
(ALC meter lights up to 1)
(ALC meter zone max.)
4.3kHz
2.2kHz
40W
±
0.3W
±
±
0.3W
±
±
±
±
±
0.5W
2W
2W
0.5W
0.05kHz
0.05kHz
1W
116
TS-2000/X
ADJUSTMENT
Item Condition
Measurement
Testequipment
Unit Terminal Unit
Adjustment
Parts Method
27. VHF SWR 1) Menu No. : 121 protection Display f. : 145.9MHz
Mode : CW
ANT : Short
Transmit
28. UHF SWR 1) Menu No. : 122 protection Display f. : 438.1MHz
Mode : CW
ANT : Open
Transmit
ANT430
• Writing data : After items 5~8 and 12~28 have been adjusted;
1) Menu No. 124
2) [+] or [–] key : Push once time. Display “rEAdy”
→
“good” (If “nG” is displayed, enter data again.)
3) [CLR] key : Push once time.
Filter VR2 29. AT detection balance
1) Display f. : 51.99MHz
Mode : CW
Power : 10W
Transmit
Oscilloscope Filter TP1
(AMD)
Power meter Rear ANT1 panel
Turn the VR2 to the point where the waveform on the oscilloscope changes from high to low.
(Threshold point)
8A
Specifications/Remarks
Ammeter Rear ANT144 Front [+] key Set the adjustment 11A panel panel or value within the limit
[–] key of the specified current.
1200MHz Unit PLL Section
Item
1. PLL reference level
Condition
1) Display f. : 1268.60MHz
Mode : FM
2. PLL reference spurious
4. LO level
(Local osc)
1) Display f. : 1268.60MHz
Mode : FM
3. VCO control 1) Display f. : 1299.99MHz
voltage
2) Display f. : 1240.00MHz
1) Display f. : 1270.00MHz
Mode : CW
Power : 1W
Carrier : 0
Measurement
Testequipment
Unit Terminal
Spectrum TX-RX3 CN16 analyzer
Unit
Adjustment
Parts Method
Specifications/Remarks
TX-RX3 L338 Output level max.
–35dBm or more at 39.6MHz.
L339
L340
L341
L342
VR1
VR2 Level min. at
31.2MHz.
DC V.M
TP2 TC301 4.5V
Check
The output level difference between 39.6MHz and
31.2MHz is 75dB or more.
±
0.05V
1V or more
Spectrum Rear ANT1.2G
analyzer panel
Set the carrier level at 100mV.
Level max.
TX-RX3 L42
L43
L45
117
TS-2000/X
ADJUSTMENT
1200MHz Unit Receiver Section
Item Condition
Measurement
Testequipment
Unit Terminal Unit Parts
1. RX IF gain 1) Display f. : 1270.00MHz
Mode : FM
SSG Rear panel
ANT1.2G TX-RX3 L22
SSG f. : 1270.00MHz
Spectrum TX-RX3 CN5
SSG output : –70dBm/70.7
µ
V analyzer (12RIF)
L24
L25
L29
Adjustment
Method
Level max.
2. MCF 1) Display f. : 135.495MHz
(135.495MHz) Level : –10dBm
Spectrum analyzer setting
Center f. : 135.495MHz
Frequency span : 50kHz
XdB/DIV : 2dB
RBW : 1kHz
VBW : 1kHz
Tracking generator
Spectrum analyzer
CN8
CN7
L26
L27
L28
Specifications/Remarks
Adjust the coils to obtain the frequency response as shown.
Max. 3dB Max. 3dB
7.5kHz 7.5kHz
• Perform the following in the adjustment mode. Item 3~7.
To terminate the adjustment menu in the middle, save your settings with Menu No. 124.
3. 1.2G SSB
IF gain
(AGC start level)
4. 1.2G SSB
S-meter
S1
1) Menu No. : 52
Display f. : 1270.20MHz
Mode : USB
AGC : ON
RF GAIN : MAX
SSG output : –116dBm/0.35
µ
V
SSG Rear panel
ANT1.2G Front panel
[+] key Change the adjustor ment values within
[–] key the range of 1 to 5 on the display.
1) Menu No. : 53
Display f. : 1270.20MHz
SSG
Mode : USB AF V.M
SSG f. : 1270.20MHz
Oscilloscope
SSG output : –113dBm/0.501
µ
V DM. SP
Rear ANT1.2G Front [+] key 1 push panel panel or
EXT. SP [–] key
S-meter lights up to S1 level.
S-meter lights up to S9 level.
S9 2) Menu No. : 54
SG output : –93dBm/5.01
µ
V
Full scale
(Lights up all)
3) Menu No. : 55
SSG output : –43dBm/1580
µ
V
5. 1.2G FM
S-meter
S1
1) Menu No. : 56
Display f. : 1270.20MHz
Mode : FM
SSG f. : 1270.20MHz
SSG output : –117dBm/0.316
µ
V
Full scale
(Lights up all)
3) Menu No. : 57
SSG output : –95dBm/3.98
µ
V
6. 1.2G ALT
7. 1.2G
FM SQL threshold
1) Menu No. : 58
Display f. : 1270.20MHz
Mode : FM
SSG output : –53dBm/501
µ
V
1) Menu No. : 67
Display f. : 1270.20MHz
Mode : FM
SSG output : OFF
S-meter lights up all.
S-meter lights up to S1 level.
S-meter lights up all.
• Writing data : After items 5~8 and 12~28 have been adjusted;
1) Menu No. 124
2) [+] or [–] key : Push once time. Display “rEAdy”
→
“good” (If “nG” is displayed, enter data again.)
3) [CLR] key : Push once time.
118
TS-2000/X
ADJUSTMENT
1200MHz Unit Transmitter Section
Item
1. TX IF gain
Condition
1) Display f. : 1270.00MHz
Mode : CW
Carrier : 0
Transmit
Measurement
Testequipment
Unit Terminal Unit
Spectrum Rear ANT1.2G TX-RX3 analyzer panel
Power meter
Adjustment
Parts Method
Set the carrier level at approx. 100mW.
L2
L3
L9
Power max.
Specifications/Remarks
2. MCF 1) Disconnect the cable from CN5.
Tracking
(135.395MHz) Display f. : 135.395MHz
generator
Spectrum analyzer setting
Center f. : 135.395MHz
Frequency span : 50kHz
XdB/DIV : 2dB
Spectrum analyzer
RBW : 1kHz
VBW : 1kHz
Transmit
Connect the cble to CN5.
CN15
CN14
L320 Adjust the coils to
L321 obtain the frequency
L5 response as shown.
Max. 3dB Max. 3dB
7.5kHz 7.5kHz
• Perform the following in the adjustment mode. Item 3~6.
To terminate the adjustment menu in the middle, save your settings with Menu No. 124.
3. 1.2G
power POC
10W
5W
1) Menu No. : 109
Display f. : 1270.10MHz
Mode : USB
Transmit
2) Menu No. : 110
Transmit
Power meter Rear ANT1.2G Front [+] key Set the adjustment 10W
±
0.3W
panel panel or value within the
[–] key limit of the specified power.
5W
±
0.2W
2.5W
3) Menu No. : 111
Transmit
2.5W
±
0.1W
1W 4) Menu No. : 112
Transmit
1W
±
0.1W
10W
±
0.3W
4. Band TGC 1) Menu No. : 113
1240MHz Display f. : 1240.10MHz
Mode : USB
Transmit
1270MHz 2) Menu No. : 114
Display f. : 1270.10MHz
Transmit
1299MHz
5. 1.2G
power PGC
2.5W
1W
3) Menu No. : 115
Display f. : 1299.9MHz
Transmit
1) Menu No. : 116
Display f. : 1270.10MHz
Mode : USB
Transmit
2) Menu No. : 117
Transmit
6. 1.2G
protection
1) Menu No. : 123
Display f. : 1270.10MHz
Mode : CW
ANT : Open
Transmit
Ammeter
2.5W
1W
7A
±
±
±
0.1W
0.1W
0.1A
If the current is less than 7A, the value is calculated as a maximum current –0.2A.
• Writing data : After items 3~6 have been adjusted;
1) Menu No. 124
2) [+] or [–] key : Push once time. Display “rEAdy”
→
“good” (If “nG” is displayed, enter data again.)
3) [CLR] key : Push once time.
119
TS-2000/X
Adjustment Points (Upper Side)
ADJUSTMENT
FILTER UNIT
(X51-315)
TC1
VR1
TP1
(AMD)
VR2
FINAL UNIT
(X45-360) (A/2)
VR102
TC101 TC102
VR1
VR2
CN11
VSR
FRONT
FILTER UNIT
TC1 : Null
VR1 : Power frequency characteristic
VR2 : AT detection balance
FINAL UNIT (A/2)
TC101,102 : VHF Maximum power
VR1,2,102 : Final idling current (HF/VHF)
120
TS-2000/X
ADJUSTMENT
Adjustment Points (Lower Side)
J2
KEY
J1
PADDLE
CN906
430ANT
G/11
TP504
UCV
TC404
H/11
TP503
VCV
TC405
E/11
TP512
VRCV
TC406
TP502
HCV
TC408
D/11
TP501
HRCV
TC410
TC409
J/11
TC403
W503
VULO2
GND
L422
L427
TX-RX 2 UNIT
(X57-606) (B/11)
TX-RX 2 UNIT
(X57-606) (C/11)
TP505
HCV2
I/11
K/11
TC400
TC402
TP506
BCV
TC401
L163
L164
CN19
ADJ
TC9
L23
TC1
L34
TC2
L47
TC3
L55
CN15
ADJ
L80
L82
L86
TX-RX 2 UNIT
(X57-606) (A/11)
FRONT
SSM
L28
L44
L52
L91
L90
TC12
TC10
L93
TC13
TC5
TC4
TC14
TC6
TC8
CN4
14TX
TX-RX 2 UNIT (B/11)
L422,427 : 31.2MHz level
TX-RX 2 UNIT (D/11)
TC403 : Lock volatge (HF REF VCO)
TX-RX 2 UNIT (E/11)
TC406 : Lock volatge (VHF REF VCO)
TX-RX 2 UNIT (G/11)
TC404 : Lock volatge (UHF PLL)
TX-RX 2 UNIT (H/11)
TC405 : Lock volatge (VHF MAIN PLL)
TX-RX 2 UNIT (I/11)
TC402 : Lock voltage (HF LO2 PLL)
TX-RX 2 UNIT (J/11)
TC408 : Lock voltage (HF1 MAIN PLL)
TC409 : Lock voltage (HF3 MAIN PLL)
TC410 : Lock voltage (HF2 MAIN PLL)
VR902
VR901
TC901
FINAL UNIT
(X45-360) (B/2)
TX-RX 2 UNIT (K/11)
TC400 : Lock volatge (SUB1 PLL)
TC401 : Lock voltage (SUB2 PLL)
TX-RX 2 UNIT (A/11)
L23,34,47,55,163,164 : MAIN VHF BPF
L28,44,52 : Sub band BPF
L80,82,86 : RX IF gain (VHF)
L90,91,TC4~6,8,10 : TX BPF (UHF)
L93 : Sub band FM discriminator coil (VHF)
TC1~3,9 : MAIN UHF BPF
TC9 : Trap frequency (UHF)
TC12~14 : TX BPF (VHF)
FINAL UNIT (B/2)
VR901,902 : Final idling current (UHF)
TC901 : UHF maximum powe
121
TS-2000/X
ADJUSTMENT
Adjustment Points (Lower Side)
J6
PANEL
J5
D-SUB
J3
SP2
J2
SP1
J7
EXT. CONT
J8
ACC2
J4
REMOTE
CN9
(TP5)
CN6
(TP4)
L64
L63 L62
L54
VR1
CN5
L68
L67 L66 L65
L69
L71
VR4
VR3
VR2
L102
L103
L100 L99
L105
TP3
L108
L98 L96
L109
L614
TP1
TC3
L613
L83
S1
L87
TP2
L46 L45 L44
L34
L25
L33 L32
L24 L23
J1
EXT RX
ANT
TC1
TC2
CN14
HFTX
TX-RX 1 UNIT
(X57-605) (A/9)
L81
TPNB
L82
TX-RX 1 UNIT (A/9)
L23~25,32~34,44~46 : HF BPF
L54,62~64,68 : MCF (69.085MHz)
L65~67 : MCF (72.925MHz)
L69,71,87,613,614 : HF RX IF gain
L81,82 : NB gain
FRONT
L83 : FM discriminator coil (HF)
L96,98~100,102,103,105,108,109 : TX IF gain (HF)
L96,98,99,100,102,VR3 : TX IF BPF (HF)
VR1 : 1st mixer balance
VR2 : TX mixer balance
VR4 : Gain balance
TC1,2 : RX trap (E type only)
TC3 : 29.1MHz frequency
122
ADJUSTMENT
1200MHz Adjustment Points
FRONT
IC2
IC3
L399
L338
VR2
VR1
TP2
L340
L341
L342 CN16
CN15
TC301
L42
L43
L45
CN11
CN13
L320
L321
L9
L5
L3
CN5
12TIF
GND
12RIF
GND
L2
L25
L27
L26
CN14
L22 L24
L28
L29
CN7 CN12
CN8
TX-RX 3 UNIT
L2,3,9 : TX IF gain
L5,320,321 : MCF (135.395MHz)
L22,24,25,29 : RX IF gain
L26~28 : MCF (135.495MHz)
L42,43,45 : LO level (Local osc)
L338~342,VR1 : PLL reference level
VR2 : PLL reference spurious
TC301 : VCO control voltage
TS-2000/X
TX-RX 3 UNIT
(X57-607)
CN4
12ANT
CN14
GND
123
Advertisement
Key features
- Satellite communication
- Independent FM/AM sub-receiver
- Noise blanker
- Digital IF filter
- Digital AGC
- Speaker separation function
- IF/AF DSP
- Triple conversion
- Quadruple conversion
