- No category
advertisement
Setting Up Printers
Adding a Local TCP/IP Printer
To add a local printer with TCP/IP port:
1. Perform steps 1-6 as described in the previous section.
The Select the Printer Port window is displayed.
64 FSMS Developer Guide version 8.4.6
Setting Up Printers
The Add Standard TCP/IP Printer Port Wizard start-up window is displayed.
5. Confirm that the printer is turned on and you are connected to a configured network.
To continue, click Next.
The Add Port window is displayed. adding. queue name for the port your printer is connected to on the TCP/IP Print Server.
FSMS Developer Guide version 8.4.6 65
Setting Up Printers
The Additional Port Information Required window is displayed.
9. Select the port type from the Device Port pull-down list. This example uses Port 1
(Parallel) as the sample port type.
10. Click Next.
The Completing the Add Standard TCP/IP Printer Port Wizard window is displayed, summarizing the information you added during printer installation.
66
11. If you want to make changes to this configuration, click Back. To accept the port installation as displayed in this window, click Finish.
FSMS Developer Guide version 8.4.6
The Add Printer Wizard window is displayed.
Setting Up Printers
12. Click Have Disk.
The Install From Disk window is displayed.
13. Click Browse.
FSMS Developer Guide version 8.4.6 67
Setting Up Printers
The Locate File window is displayed.
14. Navigate to the folder where the printer drivers are stored, such as C:/W2K
Drivers/Printer/Zebra/2348Plus.
15. Click Open.
The Install From Disk screen is displayed showing the path where the drivers are located.
16. Click OK.
68 FSMS Developer Guide version 8.4.6
Setting Up Printers
The Add Printer Wizard window shows the manufacturers and printers information.
17. In the Manufacturers pane, select the manufacturer of the printer.
18. In the Printers pane, select the printer model.
19. Click Next.
The Add Printer Wizard window displays Name Your Printer information.
20. If the default value in the Printer name box is not the name of the printer you want to use, click in the box and change the printer name.
21. To set this printer as your default printer, click Yes. Otherwise accept the default value of No and continue to the next step.
FSMS Developer Guide version 8.4.6 69
Setting Up Printers
22. Click Next.
The Add Printer Wizard window displays the Printer Sharing information.
23. Click Share as.
24. Accept the default value or enter a new printer name in the Share as field.
Note: This name becomes part of the UNC name. The UNC name consists of the computer name or computer IP address and the printer share name
(\\computer\zebra234 or \\192.168.0.5\zebra234). If you use more than 12 characters, or you use spaces, in the name, the following message window is displayed:
25. If this message window displays, click Yes. Otherwise click Next.
70 FSMS Developer Guide version 8.4.6
Setting Up Printers
The Location and Comment window allows the printer to be identified with a location.
26. Enter a location or comment, or leave the boxes blank.
27. Click Next.
The Add Printer Wizard window displays Print Test Page information.
28. Click No. Printing a test page is not necessary and, in the case of some label printers, may not work.
29. Click Next.
FSMS Developer Guide version 8.4.6 71
Setting Up Printers
The Completing the Add Printer Wizard window is displayed, summarizing the information you added during printer installation.
30. To make changes to the configuration, click Back. To accept the settings, click
Finish.
If the driver is not found, the Files Needed window is displayed.
31. Click Browse to navigate to the WinNT folder for the driver file.
72 FSMS Developer Guide version 8.4.6
The Locate File window is displayed.
Setting Up Printers
32. Open the WinNT folder. Click the appropriate driver.
33. Click Open.
The Files Needed window shows the new path.
34. Click OK.
The Printers window shows the printer you just added, with a hand under the printer indicating that it is shared.
35. Close the Printers window.
FSMS Developer Guide version 8.4.6 73
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 5 Introduction
- 5 Document Organization
- 6 Installing FSMS
- 6 System Requirements
- 6 Minimum System Requirements
- 6 FedEx-Tested System Requirements
- 7 Supported Thermal Printers
- 7 Supported Dot Matrix Printers
- 7 Supported Laser Printers
- 7 Supported Servers
- 8 Supported Scales
- 8 Network Connection Requirements
- 9 Pre-Installation Checklist
- 10 Recommendations
- 10 Your FedEx Account
- 11 Administrator User Rights
- 11 File Transfer Protocol
- 11 Network Connections
- 11 CSP Installations and Solutions Type
- 12 Uploading Revenue Files Before Upgrades
- 12 Post-Installation Checklist
- 13 How to Install FSMS
- 13 Passwords
- 13 Installing FSMS
- 23 How to Uninstall FSMS
- 24 Configuring FSMS
- 25 Starting the Configuration Utility
- 28 Shipper Settings
- 28 Managing Meter Numbers
- 29 Adding a Child Meter Number to an Existing FSMS Installation
- 30 Adding a Master Meter to a New FSMS Installation
- 31 Deleting a Child Meter
- 32 Configuring a New Meter
- 34 Remote Configuration
- 34 Adding an IP Address
- 35 Editing an IP Address
- 35 Deleting an IP Address
- 36 Connecting to an IP Address
- 37 Report Settings
- 40 Selecting a Printer for FSMS Reports
- 41 Selecting a Reports Directory
- 41 Changing Paper Size and Number of Copies
- 41 Saving Changes to the Printer Settings
- 42 Label Settings
- 46 Doc-Tab Settings
- 47 System Settings
- 49 IPD / IED / IDF Settings
- 50 Tracking Numbers Settings
- 51 Meter Settings
- 51 Express Options
- 52 Ground Options
- 53 SmartPost Options
- 53 Software ID Data Capture
- 54 Handling Charges Configuration
- 55 Handling Charge Calculation
- 55 Handling Charge Level
- 55 Handling Charge Amount
- 56 Managing Your Handling Charge Entries
- 56 Configuring Meter Settings Using the 070 Meter Query Request
- 57 Advanced Settings
- 59 Setting Up Printers
- 59 Adding a Local Printer
- 68 Adding a Local TCP/IP Printer
- 78 Windows 2000 Additional Configuration Needed
- 80 Adding a Windows Network Printer
- 82 Printing to a Windows-Based Print Share Network
- 83 Adding a FEDEXUSER Account to a Printer
- 85 Windows Print Manager Driver Support
- 85 Printer Troubleshooting
- 86 Index